Search Documents

By M. Ito

Cobalt-rich ferromanganese crust and nodule ores from seamount areas contain volcanic and sedimentary rocks as substrate or nuclei. These ores require mineral processing to remove the sub-strate/nuclei rock before smelting. This paper reviews experimental results of previous investigations. Observations and analysis of 10 samples from different localities were carried out and it was found that the liberation ratio of crushed product was high even at coarse size fraction, 0.5mm to 4mm. Experimental and calculated results in the smelting stage confirmed that the separation product satisfies the standards of the subsequent smelting process if the substrate/nuclei rock is removed from the 0.5mm to 4mm fraction with high separation efficiency. There was a density difference between the substrate/nuclei rock and the ferromanganese component. Thus the coarse sized sample was treated with gravity separation; air table separation was used as a dry method and jig separation as a wet method and high grade values with high recoveries were obtained by both kinds of gravity separation.

Jan 1, 2014

By L. S. Zhou

Germany-made AFX-100 multi-grade fluidized classifier, with exquisite built-in structure and unique novel design, materializes not only advanced and efficient classification, but also precise particle distribution and safe operation, in addition to lower energy consumption and operational cost. It, simultaneously in place of screw grader, water cyclone, and fine mesh sieve, is equipped with multi-function, and indicates superior advantage in comparison with other else grading facilities. As the third-generation equipment, which is efficient and modern, it, in China and therefore all over the world, will find wide application in processing both fine and ultra-fine iron ore resources. Industrial test, carried out in Benxi Steel?s Waitoushan Iron Mine, shows efficient classification, i.e., ?74µm particle contents in coarse, medium and fine products come to 6.09%,11.82% and 82.73%, respectively, while qualitative and quantitative efficiencies end up by 74.38% and 87.66%, respectively. Its separation efficiencies amount to 2.2 times as many as spiral classifiers, 1.8 times as hydrocyclones, and 1.3 times as vibration high-frequency fine screens. Another industrial test, which was practiced in Anshan Steel?s Donganshan Sinter Plant, indicates that classification qualitative efficiency comes to 65.06%, equal to 1.51 times as many as hydrocyclones; yield, 55.79%; -71µm particle contents in medium and coarse products, 42.02%; -71µm content in fine product, 95.42%; and concentration, 12.33%. Estimated separation indexes are as follows: Yield for concentrate at 31.22%, up 0.22% than that from general processing line; concentrate grade at 66.42%, up 1.13%; recovery ratio comes to 65.84%, up 1.28%, which, based on pilot study, results in 20 million yuan of economic return for Donganshan Floatation Plant.

Jan 1, 2014

By Kazutoshi Haga, Atsushi Shibayama, Altansukh Batnasan

"The aim of this study was to develop a hydromellurgical processing for removal of arsenic from high-arsenic copper sulfide ores and concentrates, providing increase in copper recovery. In this study, three different enargite ore samples containing 28.2–46.7% copper, 1.9–15.0% arsenic and 10.6–27.5% iron were used to determine optimum conditions for the extraction of copper and removal of arsenic. High pressure oxidative leaching process was preformed using various leaching reagents such as sulfuric acid (H2SO4), ferric sulfate (Fe2(SO4)3), hydrochloric acid (HCl), ferric chloride (FeCl3), sodium sulfate (Na2SO4), sodium chloride (NaCl) solutions and distilled water (DW), respectively, under the fixed conditions which were selected to be as follows: NaCl concentration, 0.34 M; concentrations of other leaching reagents, 0.1 M; particle size, -45 ?m; pulp density, 100 g/L; agitation speed, 750 rpm; leaching temperature, 160 ?C; leaching time, 60 min and total pressure (oxygen gas and vapor pressure) into an autoclave, 1 MPa. Results show that under the leaching conditions, more than 90% of copper leaching was achieved with lower than 2% arsenic content as a consequence of the formation of arsenic precipitates in a solution of Fe2(SO4)3–NaCl. It was determined that copper, arsenic and iron concentrations in the pregnant leach solution were 42 g/L, 0.3 g/L and 0.3 g/L, respectively. As a result, it can be concluded that the Fe2(SO4)3 solution in the presence of NaCl or FeCl3 are more efficient leaching media compared to other leaching agents under the high pressure oxidation conditions, because of their high copper recovery and lower arsenic level in the pregnant leach solution.INTRODUCTION Generally, copper is usually produced from copper sulfide ores by a combination of several processes which are flotation and smelting followed by refining [1-3]. Arsenic content in copper sulfide ores tends to increase due to the depletion of high grade copper deposits, hence conventional mineral processing and metallurgical processes cannot effectively treat these ores containing high levels of arsenic to obtain consistently high purity copper concentrates. Because high levels of arsenic in copper ores/flotation concentrates reduces the value of concentrates due to the restriction of smelting process and causes it to be a source of environmental pollution [4-6]. From this point of view, the known way of prevention against high-arsenic copper sulfide concentrates in further metallurgical treatments is to develop economically and environmentally competitive technologies for removal of arsenic impurity from copper sulfide ores before treating the ores/flotation concentrates by the pyrometallurgical routes."

Jan 1, 2018

By F. Karakas

Organo-bentonite production enjoys important applications including solvent based paints and, more importantly, the production of polymer/bentonite nanocomposites. Quarternary ammonium salts in this regard are still considered as the most versatile reagents in the process of hydrophobization. In this study, a purified form of Resadiye region bentonites, which is one of the most significant sodium bentonite deposits in the world, was used. The raw Na-Bentonite was typically characterized by chemical analysis, XRD and DTA analysis and more importantly for its cation exchange capacity (CEC). Other technological properties such as swelling index, pH, apparent viscosity, water absorption, oil absorption were also conducted on the raw bentonite. The mineralogical analysis of the raw bentonite reveals that it contains about 80 % montmorillonite together with other associated gangue minerals including feldspar, quartz, calcite, dolomite, coloured impurities and other clay minerals. The raw bentonite was subjected to two stage processing involving a series of hydrocylones. Different apex and vortex diameters and different pressures were employed in order to produce a bentonite concentrate with 95 meq/100g CEC from a CEC of 71 meq/100 g. This high quality concentrate was used in the production of organo-bentontonite. The modification was performed with two different quaternary amines, i.e. Trimethyl Phenyl Ammonium Chloride (TPAC) and Hexadecyl Trimethyl Ammonium Bromide (HDTMA-Br). In the modification procedure, three parameters, i.e., adsorption density, zeta potential, swelling index and apparent viscosity were studied simultaneous-ly from the same suspension to identify both the mechanism of the process and also the degree of hydrophobicity. Adsorption measurements were made as a function of conditioning period, pH, and reagent concentration. Simultaneous examination of the adsorption density, zeta potential and apparent viscosity enabled us to pinpoint the optimum region of hydrophobicity which was subsequently tested by settling and critical coagulation concentration in both water as polar and toluene as nonpolar solvents. The results are analyzed in the light of experimental data.

Jan 1, 2014

By F. Z. Dong

The paper is mainly about a study on the techniques of separating iron from pyrite cinder of a certain sulfuric acid plant in Shandong province. The main components of the cinder are Fe2O3 and SiO2, and the degree of liberation of iron mineral and gangue is very high. So the iron concentrate with higher degree of iron and lower grade of silicon and sulfur can be achieved by reverse flotation. The iron grade of the concentrate reaches 63% and the recovery of iron is no less than 63%. And the most important influencing factor of the flotation is the temperature of the pulp. A better guideline can be achieved by magnetic separation. The cinder is magnetizing roasted for 15 minutes with temperature of 800?, and the concentrate with the iron grade 64%, sulfur grade 0.2% and iron recovery 85% can be obtained by two stage magnetic separation. A rotary kiln has been built to deal with the pyrite cinder, and the result of the industrial magnetizing experiment and magnetic separation is satisfying.

Jan 1, 2014

By M. D. Vilarinho, W. Xuan, F. Vasconcelos Guimarães

"This article summarises the efforts to reduce the energy consumption in grinding in a magnetite ore beneficiation plant. ArcelorMittal Kryvyi Rih ore beneficiation plant produces magnetite concentrate at 65% Fe and 8% SiO2, of which the D80 is approximately 44µm after three stages of grinding with ball mills and magnetic separation. Characterisation and laboratory scale bench tests performed on samples from the beneficiation plant indicate that the industrial flowsheet could be simplified. After the first stage of grinding and magnetic separation, a significant size fraction of the intermediate concentrate is already well liberated. Therefore, it can be directly concentrated in a second stage magnetic separation without further grinding. If a screen of 150µm size can be implemented after the first stage of grinding-magnetic separation, only the oversize of screening, representing 35% of the material, requires secondary and tertiary grinding and magnetic separation. The combined concentrate from the two fractions already meets the industrial specifications. This new route can provide the same final product, with fewer mills; it saves around 30% in energy consumption only in the grinding step without changing the main structures of the processing plant.INTRODUCTION Comminution, including crushing and grinding, is responsible for at least 40% of total energy usage in mining and mineral processing. This paper shows an example to reduce grinding cost, by changing the flow sheet design strategy in ArcelorMittal Kryvyi Rih (AMKR).AMKR is one of the most important mining and steel complexes in Krivoy Rog basin in Ukraine, which has been studied over 100 years because of mining of iron ores. The iron ores are associated to Banded Iron Formation of the Saksagan suite, with an average iron grade of around 36 percent Fe. The total thickness of the Krivoy Rog Supergroup reaches 5-6 km, whereas that of the iron-ore Saksagan Group comprises up to 1400 m. High-grade iron ore extends to more than 2,000 m below present surface"

Jan 1, 2018

By Kazutoshi Haga, Ryo Kawarabuki, Atsushi Shibayama, Masato Kosugi, Masanobu Kawata, Refilwe S. Magwaneng, Kohei Mitsuhashi, Altansukh Batnasan

"The recovery of copper and iron from carbonaceous sulfide ore is of economic and environmental interest despite its processing difficulty. Hydrometallurgical methods can be used to concentrate sulfide metals of these hard-to treat ores in a simple and eco-friendly manner. In this study, high pressure acid leaching process was comprehensively studied to dissolve metals from an ore with organic carbon and carbonaceous gangue material using autoclave equipment. The sample used for the experiment was reduced to an average particle size of 75 µm after undergoing flotation to reduce carbonaceous gangue minerals. A comparative study on two leaching reagents of sulfuric acid and iron sulfate and their dosage was used to observe dissolution of copper and iron. Other parameters of temperature (90-170 0C), solid-liquid ratio (1:10, 1:5, 1:3 and 1:1) were investigated through kinetic studies to access the influence of organic carbon and carbonaceous material on recovery of copper and iron. Materials balancing analysis was used to evaluate the efficiency of metal dissolution. The effects of parameters on leaching rate and concentration was demonstrated. Results obtained from the experiment indicated low concentrations of copper and iron in pregnant leached solutions, which was attributed to acid consumption by organic carbon and carbonaceous material in feed. However, the high efficiency rates of 92.4% and 86.3 % for copper and iron respectively in sulfuric acid can be concluded that leaching of concentrates of carbonaceous ore is possible provided system control on type of acid, pH and temperature. The purpose of this research is important in understanding mechanism involved in dissolution of copper and iron in concentrates of carbonaceous ore and marks an improvement in leaching of highly contaminated ores."

Jan 1, 2018

By James A. Finch

"Developed countries are in the midst of re-structuring education in minerals-related disciplines as raw materials, once vital to wealth generation, contribute progressively less to the economy. The changing circumstances mean institutions must justify mineral processing by new criteria. After considering what a mineral processor needs to know the ways to deliver are considered. Taking twenty graduates per year to illustrate, one institute could justify this number as a program in a department or school (of whatever grouping of disciplines). A strong research component would make the package additionally attractive. Divide among four institutions and mineral processing is best served in a research centre with delivery taking advantage of multi-centre and distance learning opportunities.INTRODUCTIONThis is one of five plenary lectures at the Congress. I may have preferred a technical subject, as that is what occupies most of my thinking hours, but it is reasonable as an academic that this topic should come to one of us. The fact the topic has not been high on my agenda may provide one advantage: that I can suggest directions free of pre-conceived notions, just as when reviewing the background to a technical article the temptation to select in support of one?s interpretations is resisted. The trick will be to add something new.One reading of the title seems to query whether mineral processing education has a future. (I will refrain at this juncture from defining mineral processing and assume for now we share an understanding of the term.) The proximity of natural and human resources led to the Industrial Revolution and the interaction continues to stimulate and sustain industrial and economic development in many parts of the world. The search for raw materials has historically played a key role in opening frontier areas, with undersea and outer space next. The reason is obvious: raw materials along with food and energy underpin society. Thus mining will remain part of human activity along with the need to pass on the knowledge and skills.What happens over time is resource relocation. Raw materials become exhausted in one area to be replaced by sources elsewhere; the demand for some materials lessens while growing for others. Educational institutions can find themselves with the wrong geography or with staff focussing on the wrong subjects. When this happens the restructuring produces much discussion. This is where we are in parts of the world. Japan, Western Europe and the United States are the prominent examples (Dowd, 1998; Flemings and Suresh, 2001; McDivitt, 2002). Mineral processing is becoming a series of courses in related disciplines: resource engineering, environment engineering or materials engineering. The start of the transition is evident in Canada and Australia, perhaps earlier than expected given the contribution of raw materials to their economies. A common backdrop in the developed countries is social pressure to reduce the impact of the ?untidy? aspects of life, and that includes mining. (This is not new: in classical times the mine face was the preserve of slaves and convicts.) These values are exportable, potentially affecting recruitment into mining schools everywhere."

Jan 1, 2003

By Kari Niiranen, Patrick Krolop, Viktoria Töyrä

Luossavaara-Kiirunavaara AB (LKAB) operates an iron ore mine, three beneficiation plants and three pelletizing plants in Kiruna, Sweden. The current methods of separation in the beneficiation plants are wet low intensity magnetic separation (WLIMS) and reverse apatite flotation, where the WLIMS stage is regarded as the crucial part of silica separation from the ore. Currently, the high-grade iron ore deposit of Kiirunavaara has a low grade of silica in situ, of approximately 3.0% SiO2, but the silica grade is expected to increase in the deeper parts of the deposit with a complex silicate mineralogy. An increasing silica grade will affect especially the production of direct reduction pellets (LKAB DR Oxide Pellets), one of the main products of LKAB in Kiruna with an average silica grade of under 0.75% SiO2. The silica grade in the magnetite concentrate is normally limited to a maximum level of 0.55% SiO2 in order to achieve the required chemical composition in the pelletizing process. In order to study the possibility to reduce silicate content in the magnetite concentrate (pellet feed) in the beneficiation plants in Kiruna obtained by wet low intensity magnetic separation (WLIMS), enlarged mineral processing test work was carried out in the LKAB’s mineral processing laboratories in 2016. The test work consisted of comminution, low intensity magnetic separation and reverse cationic silicate flotation at laboratory scale, complemented by screen analysis, chemical assays and mineralogical investigation. The results of these mineral processing test work showed that the magnetic separation is not sufficient to reduce the silica content in the magnetite concentrate, particularly in the case of the high-SiO2 ore type B2-a. The reverse cationic flotation can be regarded as a possible solution to reduce the silicate content in the magnetite concentrate obtained by WLIMS and to achieve the required silica grade of less than 0.55 % SiO2 in the pellet feed. The results of this study provide a good basis to understand the behaviour of different silicates in the existing beneficiation process. Furthermore, it serves valuable information for development of new beneficiation processes and for investment in new equipment at the beneficiation plants in Kiruna in the future.

Jan 1, 2018

By H. Z. Kuyumcu

Coking of coal blends using high volatile coals with poor coking abilities to produce a high quality coke for blast furnace application can be achieved by compacting the coal blend prior to the carbonization process. Here densification up to a relative material density of 80 %, i.e. a compact density around 1100 kg/m3, has proven to be advantageous. Coal is compacted by stamping, if the so-called stamp charging process applied. Compacting of the coal by pressing is practised in case of the cokemaking with so-called heat-recovery ovens. Stamped and pressed coal cakes require over the cake volume uniform high density and mechanical stability. Besides the aspects of the coal selection, the efficiency of the process is mainly determined by the operating parameters compacting time and compacting energy for coal cake making. At the Department for Mechanical Process Engineering & Solids Processing of the Technical University Berlin the two sub-processes of densification and strengthening during stamping and during pressing are theoretically and experimentally investigated using specially developed lab-scale compacting test units and a strength test device. Describing cake density in terms of coal properties for a given coal and measured compacting energy input then leads to a compacting equation with the so-called Stampability as the integral model parameter for the stamping process. For the pressing process the cake density can be calculated with the measured compacting pressure and the Compressibility factor, respectively. Investigations were carried out to provide evidence of a significant influence of coal type, coal surface moisture, coal granulometric and mechanical properties on the densification process. The overall objective of the work is to establish a comprehensive mathematical model on the compacting behavior of large coal bulk quantities and the optimization of the compacting processes by stamping and by pressing. Keywords: coal compacting, agglomeration, stamping, pressing, cokemaking

Sep 1, 2012

By l. Bokányi

The Tóth adsorption isotherm-model was derived and has been widely used for the inhomogeneous solid surfaces. The three-parameter isotherm incorporates the effect of the interaction between the adsorbed substances as well. All classic isotherms can be clearly derived from this one. Bio sorption is the sequestering of dissolved components, i.e. metals from aqueous environment by living or dead biomass. The mechanism of the bio sorption is rather complex and predominantly refers to the affinity of the chemical functional groups: acetoamido groups of chitin, structural polysaccharides, amino and phosphate groups in nucleic acids, amino, amido sulfhydryl and carboxyl groups in proteins, hydroxyls in polysaccharides, sulphates, etc. towards the soluted substances, i.e. heavy metal ions. The physisorption, as well as the micro precipitation also play a role in the bio sorption mechanism. The description of such a complex process can be done by a model reflecting this complexity. According to our experimental results obtained using algae and immobilised algae for the sorption of heavy metal cations, the most appropriate model for such a description is the Tóth-isotherm, the parameters of which can be interpreted. Flotation process is also a very complex one, the overall result of which depends on the partial results of many micro processes and parameters. The particle interaction which very often takes place in the flotation systems makes the phenomenon even more complex. The flotation kinetic model with particle interaction was already introduced by author in 1994 and further developed in 2000. In this paper based on the experimental results obtained with metallic particles in case of recycling flotation the applicability of the Tóth-equation as an alternative flotation kinetic model for the systems with particle interaction is proved. The applicability of Tóth-model in mineral processing demonstrates again its universal character and the great talent of the late József Tóth, great Hungarian chemist. Keywords : Toth isotherm, biosorption, Langmuir, Freundlich

Sep 1, 2012

By Yi-jun Cao, Jin-cai Ran, Guo-sheng Li, Jiong-tian Liu, Li-jun Deng, Shu-lei Li

A fly ash sample from a power station in Guangdong province has been characterized by size separation, X-ray diffraction, contact angle measurements and X-ray Fluorescence. The ash sample had a loss-on-ignition (LOI) (%) of 15.54% and a large proportion of the unburned carbon was distributed in the +74 µm and -20 µm fractions. Contact angle measurements suggested that the removal of unburned carbon from the fly ash using flotation would present some challenges. The effects of various operating variables on the removal rate of unburned carbon (RUC) (%) and (LOI) (%) were determined using a cyclonic-static micro bubble flotation column (FCSMC). Within the range studied, the optimum diesel oil dosage was 1200 g/t, abies oil (frother) dosage was 600 g/t, pulp density was 20%, superficial gas velocity was 1.4 cm/s and circulating pressure was 0.20Mpa. Column flotation tests indicated that the FCSMC method a viable and effective separation process for removing the unburned carbon from the fly ash. Under the optimized conditions, a clean ash with 2.13% LOI and 94.21% RUC was obtained.

Jan 1, 2014

By P. Oliveira, A. Peres, A. Silva

"The decrease in iron content and increase in contaminants grade, associated with greater participation of compact and semi-compact materials, has impacted the recovery of a mechanical cells flotation circuit in the Iron Quadrangle, Brazil. The recovery decrease in the flotation stage motivated the current conventional flotation circuit reevaluation seeking alternatives to restore the recovery, without affecting the final concentrate quality parameters, with low investment. Sampling, chemical characterization of samples, bench scale flotation experiments, and mass balances were conducted. Analysis of the results showed opportunities to improve the circuit performance. The stages prior to the flotation circuit changes were: rougher, cleaner, recleaner and scavenger. In the previous configuration, recleaner was operated as cleaner scavenger and the iron grade in the scavenger concentrate was 23%, representing 38% of the new feed. After the circuit change, the circulating load was reduced from 38% to 15% and the iron content was upgraded to 42%, resulting in increased residence time. The iron content in the global tailings of the concentrator was decreased from 10.9% (year of 2013 average) to 10.2%, representing gains in both mass and metallurgical recoveries.INTRODUCTIONRegarding plant practice, the year 1972 represents a landmark for the concentration of iron ores in Brazil. VALE started up 28 units of WHIMS (wet high intensity magnetic separators) at the Cauê plant in Itabira, each one producing 1x106 t/year of concentrate. Later 17 WHIMS machines were commissioned at Conceição. During the 80’s decade of last century, changes in the ROM required the addition of a cleaner flotation stage to decrease the silica content in the pellet feed.The first company to use reverse cationic flotation as the only concentration operation of iron ore was SAMARCO (start up in 1977). Since 2015 flotation has been utilized at VALE in Itabira as major concentration process, magnetic separation acting as scavenger stage.The Jones matrix type WHIMS were manufactured for decades under patent by KHD Humboldt Wedag. After the expiration of the Jones patent, Eriez Magnetics took the world leadership regarding WHIMS manufacturing. The Brazilian branch of Eriez is Inbras. Based on plant practice experience at the Fabrica concentrator, the Brazilian company Gaustec was established (RIBEIRO and RIBEIRO, 2010) and is now present in different countries. The mega sized WHIMS GHX-1400 (18.000 Gauss, gaps smaller than 1.5 mm) were developed to face the challenge of huge throughput required by iron ore processing (Ribeiro et al, 2017)."

Jan 1, 2018

By A. V. Bogdanovich

In diamond ores processing, final waste tailings size, rejected to dump, is one of the most important parameters. On one side, it is necessary to minimize losses of diamonds, whose size exceeds 1 mm, on the other side ? to provide for the plant high throughput and sufficiently low capital and energy costs, which is in greater part connected with disintegration process. Extensive laboratory, pilot-scale and commercial-scale dressability studies of different types of diamond ores have been performed at JSC ?Mekhanobr Engineering? in recent years. With that, special consideration was given to determination of the required ores? disintegration size that would provide for a high recovery of diamonds. In diamond ores processing, in order to exclude breaking of large diamonds, stage disintegration is used with regrinding of light fractions and heavy fraction X-ray fluorescent separation tailings. On account of rather weak bonds of diamonds with enclosing minerals, in crushing and grinding of diamond ores, selective disintegration takes place, with aggregates? breakup along plane surfaces of least bonding, which facilitates liberation of diamonds and their transition to free state. Heavy components losses with different sizes of final dump tailings were studied in processing of large samples. It was established, that in order to almost completely exclude losses of heavy components over 1 mm size, light fractions had to be ground to 2.5-3 mm size, while X-ray fluorescent separation heavy tailings of -15+3 mm size do not contain diamonds larger 1 mm in aggregates, and their regrinding does not increase total recovery of diamonds. On the basis of the conducted studies, relationships regarding heavy components and diamonds losses with respect to diamond ores final disintegration size were obtained, providing for more rational organization of the ores disintegration and processing flow sheet. Keywords: diamond, waste tailings size, disintegration process, recovery of diamonds

Sep 1, 2012

By Anand Anupam

Conventionally, beneficiation in Indian coal washeries is done using dense medium cyclones upto the size of 0.5 mm. Coal fines below 0.5 mm size are extensively cleaned by froth flotation. There are many problems associated with flotation of Indian coals, e.g. poor response of coal particles to flotation, misplacement of fine high-ash material to froth, loss of good quality coarser coals (within ?0.5 mm size range) to tailing streams, high cost of reagents, water contamination, etc. In addition, sophisticated control systems for efficient management of the fines washing circuits are needed. Thus, there is an escalation in the capital and processing costs. In view of these facts, studies were carried out to establish the cleaning potential of dense medium cyclones for beneficiation of fine coal down to a size of 0.1 mm, essentially aimed at reducing the load on fine coal circuits mainly comprising of flotation. ROM Coal (in the size range of -2 + 0.1 mm) obtained from JogtaOCM,Jharia coalfield possessing relatively low ash (about 21%) was used in this study. Purpose for using low ash coal was to further lower, its ash content down to 8% which is comparable, to the ash content of imported coal. After characterization studies, nine tests were carried out on the prepared feed sample for its beneficiation using a dense medium cyclone of non-conventional design (very low cone angle and longer barrel), by varying its apex and vortex finder diameters. The efficiency of separation has been evaluated using Tromp curves. It could be established that it is possible to produce a clean coal of 8% ash, with Ep value of 0.044, using Jogta OCM coal by treating it in a modified dense medium cyclone. These results are summarized and discussed in detail in the present paper. Keywords: dense medium, cyclone, fine coal, beneficiation, Jharia coal

Sep 1, 2012

By Ben Murphy, Alejandro Yanez, Tatu Miettinen

"Flotation using large volume cells has grown in importance during recent years, particularly given the increasing demand for minerals whilst ore grades are decreasing. Outotec introduced the TankCell® e300 in 2007 to enable concentrator plants to process these higher tonnages. From the beginning, TankCell® e300s with FloatForce® mixing mechanisms have demonstrated good metallurgical performance with decreased operating costs and high availability. This paper deals with specific engineering challenges that need to be considered when installing these units rather than giving examples of performance. Today there are over 100 TankCell® e300s operational worldwide. As more of these units are installed new technical challenges are encountered and solutions developed to maximize their productivity. Lessons have been learnt by operators, engineering companies and the cell manufacturers on how best to design and layout these cells in modern concentrators to ensure smooth transition from design to installation to operation. This paper presents information on important design considerations and learning that has been obtained through the design, installation and commissioning of the TankCell e300 around the world. Areas pertaining to cells layout such as feed and discharge arrangements along with items of metallurgical concern such as sampling, reagent addition and the potential benefits of installing a variable speed drive on the motor will be covered in depth."

Jan 1, 2014

By I Brum

Brazil and Colombia have large reserves of coal, those reserves in Brazil are located predominantly in the south and Colombia the main reserves are located in the north. Despite the relative ease of exploitation, these resources have been underestimated as a source of energy. Currently, these countries are developing projects and partnerships aiming to qualify this mineral resource, adding quality to the final product of the processing plants. In this scenario the processing of Brazilian and Colombian coal in flotation columns appears as a promising alternative, having been successful in mineral systems containing fine particles This paper aims to study the overall process of column flotation for a specific Brazilian coal and a specific Colombian coal. The material used in this study consists of fine coal from Brazil (Copelmi) and Colombia (Cerrejon). The objective is to recover carbonaceous matter and reduce the ash and contaminants grade. The two coals were floated using a negative bias in a 5 cm diameter conventional flotation column of 5 m high. Flotation parameter investigated included air velocity in the range 0.6 to 1.5 cm/s. For all runs, a constant negative bias of -0.25 cm/s and a pulp concentration of 8% w/w were used. For Cerrejón coal, 300 g/ton of frother and 907 g/ton of collector was used, whereas for Copelmi coal, 600 g/ton of frother and 1815 g/ton of collector was employed. The frother was a commercial Aerofroth 65 (AF65), whereas the collector was Kerosene. For the Colombian coal, in general, yield, organic recovery, ash recovery and water recovery decreased with the increasing air rate. However, for Brazilian coal the air rate had no significant effect. For Colombian coal, the highest yield (60% w/w) and organic recovery (69% w/w) were obtained at the lowest air rate (0,6 cm/s). Keywords: negative bias, column flotation, coal

Sep 1, 2012

By Luis Bergh, Francisco Díaz, Isabel Panire, Juan Yianatos, Luis Vinnett

"In this paper, industrial data of residence time distribution (RTD) in mechanical flotation cells is presented, which were measured in several plants using the radioactive tracer technique. Results include mechanical flotation cells of 100 - 300 m3, which were operated with effective residence times from 2 to 7 min. Tests were developed in forced air and self-aerated cells for liquid and solids (non-floatable) per size classes. Different RTD model structures including perfect mixer, Large and Small Tanks in Series (LSTS) and by-pass flow plus perfect mixer were evaluated and compared for single cells. The actual mixing regime was related to the effective residence times and cell designs based on the model fitting. By-pass flow percentages were typically lower than 10%, therefore the perfect mixer model plus a dead time was a suitable model structure in most cases. On the other hand, the arrangement of cells in series was effective in reducing the bypass flow observed in single cells (by-pass flow percentage greater than 5%). In addition, the N perfectly mixed reactor in series model was used to represent the mixing regime along flotation banks, which were operated with mean residence times in the range of 18 - 53 min. Results showed that N tanks in series plus dead time were closer to the actual values in most cases."

Jan 1, 2014

By Yury V. Kulikov, Rakan Rahbani, Arkady Y. Senchenko

"The relevancy of complex minerals treatment is constantly increasing taking into account mineral resources depletion. Different refractory ores and concentrates, oxidized and polymetallic ores, as well as metallurgical products (slags) can be assigned to such mineral type. The treatment of such products via conventional flowsheets requires considerable capital and operational costs and does not always provide high recovery level of valuable components into a saleable product. Therefore, considerable amount of ores and metallurgical products are not treated, or treated inefficiently. One of the most promising approaches that allows economic treatment of refractory products is their ultrafine grinding down to 5-20 µm with subsequent processing or hydrometallurgy. Horizontal bead mills - the IsaMillTM, developed by Xstrata Technology, received their wide application in mining industry. Standard testing is performed under laboratory conditions in an M4 IsaMillTM (volume - 4 liters) to define the parameters of fine grinding. This mill completely simulates the operation of full scale industrial mills up to 50 m3 in volume (up to 8000 kW motor). The paper describes fine grinding technology performed in bead mills, and the importance of testing according to a certified method for industrial equipment selection. The paper contains description of promising directions of fine grinding technology application for several projects in Russia and Kazakhstan."

Jan 1, 2014

By K. Hori

In this study, the determination of optimal conditions for jig separation has been investigated with a TACUB jig separator. The TACUB jig, from which a Batac jig originated, is a useful gravity separator that is effective to separate crushed solid wastes as well as coarse ores. A mixture of crushed polyethylene (specific gravity 1.3) and polyvinyl chloride (specific gravity 1.5) was separated by a batch TACUB jig by varying the frequency (wavelength) and the amplitude (pulse stroke length). It was found that the sample particle layer in the separation chamber was fluidized without turbulence by the rising water pulse resulting in the separation. However, a too strong water pulse reduced the efficiency of the separation of the particles. The results indicate that the specific velocity of the rising water is necessary to fluidize the particle layer without turbulence to separate the particles. The expansion ratios of the thickness of the particle layer in rising flows were measured in a cylindrical column. The pressure losses by the particle layer were calculated from the expansion ratios and the velocity of the rising flows by Ergun?s equation. The curve of the pressure loss vs. the velocity of rising flow showed a maximum point corresponded to the point of fluidization. The velocity of a rising flow on the point of fluidization provided the optimal separation condition.

Jan 1, 2014