Search Documents

By D. Steele, B. Ndlovu

"Adequate characterisation of clays is becoming increasingly important as operating mines move into areas of more complex ores. The processing therefore needs better mineralogical characterisation to identify problematic ores for better planning before issues arise. While a number of instrumental mineral characterisation methods are available, X-ray Diffraction (XRD) is widely recognised as perhaps the best technique for the identification and quantification of minerals, particularly clays. When an appropriate sequential and systematic sample preparation and treatment protocol is employed with instrumental XRD analysis individual clays can be uniquely identified, and the proportions of interstratified clays can also be quantified. The effect of sample preparation on the XRD analysis and identification of clays was investigated in this study. The results showed that sample preparation protocol is indeed critical to accurately analysis and characterisation of clays. For example, both dry grinding and micronizing affected the degree of crystallinity of kaolinite leading to the formation of reactive surfaces or changes in the physicochemical behavior. It was also found that the apparent degree of preferred orientation in platy minerals correlates directly with the amount of force/pressure applied during the preparation of backfilled powder samples. This work showed that manual preparation can produce highly variable peak intensities especially with minerals that show any preferred orientation. KEYWORDS Clay; XRD; kaolinite INTRODUCTION Clays are important in our life and they have numerous applications in modern world from cosmetics to environmental remediation. Therefore, clays have been extensively investigated for many years. Adequate characterisation of clays is becoming increasingly important as the mineral processing industry faces more complex mineralogy with the need for better mineralogical characterisation to identify problematic ores and plan accordingly. In most studies, X-ray diffraction (XRD) method has shown the unique capability to characterise mineralogy, especially for the fine grained size materials. The XRD technique is particularly diagnostic for clays. It is known that under ideal conditions, the peak intensities of an XRD diffractogram are proportional to the concentrations of individual minerals present in the sample. Hence, the qualitative mineralogical data obtained from XRD can be quantified, using either the internal or external standard methods. However, it is also known that clays are particularly sensitive to the influences of sample preparation method due to their physical characteristics (e.g. fine grain size, morphology, relative physical softness, crystallinity, thermal sensitivity) that could be destroyed by inappropriate preparation prior to the analysis. Thermal and mechanical treatment and grinding of clays can change their crystalline structure, and consequently, their characterisation results by XRD analysis. The behaviour of clays in grinding has been widely studied, especially for kaolinite (Miller and Oulton, 1970, Milocevic et al., 1992, Tomasevic-Canovic et al., 1992). With prolonged grinding time, the crystallinity of the clays can decrease (Filipovic-Petrovic et al., 2002). It has been shown that grinding may gradually cause the loss of hydroxyl ions of kaolinite (Gonzalez Garcia et al., 1991)."

Jan 1, 2018

By D. Saramak

Investigations over the application of hybrid comminution circuits with the High-Pressure Grinding Rolls (HPGR), on the main comminution stage on the basis of the lime and cement industry, were presented in the paper. Two crushing circuits were investigated, the first HPGR-based and the other one, with conventional jaw crusher. The results presented in the article confirm that hybrid comminution circuits with the application of HPGR are innovative ones, and they assure achieving the technological and economic competitiveness in the mineral raw materials processing industry. They are much more favorable in terms of the final product fineness and capacity but insignificantly less effective about the unit energy consumption. Technological performance of conventional crushing circuit and HPGR-based one were also compared in lab scale. The circuit with HPGR application gives finer products both on crushing and grinding stages. The average particle size reduction obtained in HPGR-based circuit is as much as twice greater, comparing to the conventional crushing devices. Keywords: comminution, HPGR technology

Sep 1, 2012

By G. K. Nimal Subasinghe

The establishment of grind size that optimally liberates the valuable mineral for efficient down-stream processing is of great importance for most mineral processing operations. Reasonably accurate comminution models as well as models of downstream separation processes may be found in the literature but their use in optimizing grind size is limited without an associated liberation model. In this work, an attempt has been made to address the above shortcoming by demonstrating how the effective parameters of the downstream flotation process may be predicted from the liberation characteristics based on the ore texture data for a disseminated nickel ore. In this regard, the liberation model based on linear intercept distributions of mineral and gangue proposed by King (1979) and its application to predict the flotation performance of an industrial plant demonstrated by Schaap (1979) may be considered useful contributions. However, while the model proposed by Schaap is simplistic enough, it is based on several assumptions due to the non-availability of intercept length measurements on the parent rock, in particular, on the extent of mineral exposure on the surface of comminuted particles. In this work, the linear mineral and gangue intercepts on polished specimens of a binary ore, comprising darker pentlandite as the valuable mineral and lighter barren host rock were measured using an image analyser. The resulting intercept distributions followed negative exponential distributions. Using the mean sizes of mineral and gangue intercepts, the proportion of liberated, compo-site and mineral occluded particles of a given size, the extent of mineral exposure on the surface of particles and their mean mineral contents were calculated using principles of renewal theory. The rock was then crushed and ground and different size fractions were floated. It has been shown that the parameters of observed recovery data based on 1st order kinetics such as the associated rate constant and ultimate recovery agrees well with those predicted from the quantities calculated above. This work has important practical implications since it can indicate variations in flotation performance arising from changes in mineralization within a large ore body.

Jan 1, 2014

By Carlos Rabanal, Levi Guzmán

"The concern regarding grinding media consumption rates is as old as the invention of the tumbling mill. Over the years many materials and grinding media shapes have been tested. Through all this, steel grinding balls have proved to be the most effective media for comminution in tumbling mills. There have been several approaches to be able to the wear of the ball charge in any given mill, all of them based on limited empirical evidence. The mining industry still utilizes the Bond Abrasion test that was developed in the 1960´s. As shown later in this publication, this approach shows error greater than 60%. More recently, in 2007, Radziszewski from Mc Gill University has proposed a different total grinding media wear model; this model is based on decoupling the effects of the abrasion, corrosion and impact wear mechanisms. Also in 2007, Benavente, at the time with Moly-Cop Peru, presented an empirical model relating both ore properties and operational conditions that would affect the wear performance of the grinding media. For the database referred in this article, Benavente’s model shows an average error of ± 12% which represents a higher degree of improvement in comparison with previous approaches. The current paper presents recent research conducted by Moly-Cop Peru to further improve the capability of the empirical model originally developed by Benavente to estimate grinding media wear rates. The work performed included extensive determinations of the Bond Abrasion Index for different types of ores, collected at industrial grinding applications where the corresponding operational information was made available. The results of the research enabled us to build a more robust and confident model for estimating the grinding media wear rate. The average error of this new model is in the order of ± 9% which is a significant improvement over the models previously described."

Jan 1, 2014

By T. C. Sun

Two wasted activated sludges (WAS), from an industrial wastewater treatment and a sewage treatment plant respectively, and 7 collectors are used to investigate the feasibility of air flotation thickening of WAS by adding the collectors used in mineral processing. The collectors experimented include straight chain fat acids with different chain length, sodium oleate, alkyl sodium sulphonate, sodium dedecylsulfonate, and dodecylamine. The results show that the thickening efficiency varied depending on different collectors. Of the collectors experimented, dodecanoic acid and dodecylamine are best collector for thickening both sludges.

Jan 1, 2014

By Yu. Gurevich, M. Teremova, I. Prokopev, A. Razvjaznaya, N. Algebraistova

"The objective of this work is the scientific justification and development of efficient and environmentally-friendly method of bulk concentrate preparation for selection with application of microbiological practices. This research suggests to apply Pseudomonas Japonica bacterial culture to the bulk concentrate before the selection circuit in order to clear the surface of sulphides from the xanthate skin. It is also suggested to apply bacterial consortium Ochrobactrum ?nthropi and Pseudomonas aeruginosa JCM 5962 for desorption of diesel residual concentrations. High-efficient and environmentally friendly method of copper-molybdene and lead-zinc bulk concentrate selection was developed based on theoretical and experimental research work with application of microbiological practices. In comparison with conventional methods (steaming, sodium sulphide washing) the above suggested bio-technological method of bulk concentrate preparation before selection cycle will allow to reduce material and power expenditures, and it is also environmentally friendly. INTRODUCTION High-efficient selection of sulphide bulk concentrate is gained exclusively after collecting agent is removed from mineral surface. Therefore, the problem of bulk concentrate preparing before the selection cycle is acute, since the further technological parameters of the subsequent separation depends on the effectiveness of pulp preparation. Existing traditional ways of bulk concentrate preparation. such as washing or steaming, are characterized by high energy and material costs in industrial conditions [1,2]. The microbiological treatment before separation of the bulk concentrate into different kind of concentrates appear one of perspective processes for treatment of bulk concentrates [3,4]. At the present time, the world practice of processing mineral raw materials demonstrates the wide application of technologies using microorganisms: bacterial leaching and oxidation, purification of industrial wastewater. This is due to the fact that biotechnological methods are environmentally safe, low-cost, and suitable for refining complex ores and raw materials of industrial origin."

Jan 1, 2018

By P. Chris Pistorius, Johannes Sono, Rossouw Sono, J. J. Kobus

Different coal properties are important in SL/RN (coal-based rotary kiln) direct reduction of iron ore, and in electrical smelting of prereduced iron ore. These differences were highlighted when a plant which processes titaniferous magnetite had to change to different coal types after decades of operation. Laboratory simulation was used to evaluate two candidate coals, which were similar in volatile content and rank, but differed in reactive maceral content. Direct reduction was evaluated by isothermal experiments using a packed bed of ore and coal, measuring the off-gas composition to determine reaction rates and departure from equilibrium. These indicated reduction to be under mixed control, and quite sensitive to temperature (confirming that the coal reactivity is of importance). An aspect of electrical smelting was assessed by determining dissolution rates of the coal in molten iron at 1550°C. Dissolution rates did correlate with differences in coal structure, as determined by X-ray diffraction, with the more ordered ("more crystalline") coal dissolving faster. The conclusion is that the coal which is more reactive during direct reduction is less reactive during dissolution. However, it is concluded that controlling the temperature during direct reduction offers a feasible method to reconcile the two process steps.

Jan 1, 2003

By M. Holuszko, I. Mikhalev

"Previous studies described by Galvin et al. (2017) have shown that for Australian bituminous coal fines, both in batch and in continuous process, the new improved oil agglomeration procedure based on the use of high-internal-phase (HIP) emulsions, as compared to the conventional “pure oil” agglomeration process, enables a significant reduction in the amount of oil while reaching a high yield of clean coal (approximately 90% of agglomerates greater than 355 µm in size) in a significantly shorter time. The HIP emulsion used in these experiments comprised up to 95% vol. aqueous solution of sodium chloride (3% wt. concentration) and for the rest, a mixture of kerosene (oil) and sorbitan monooleate (SMO emulsifier) in a 1:1 ratio as a binder. This study evaluates the applicability of the new HIP-oil agglomeration process to treat Canadian bituminous ultra-fine coal and Russian sub-bituminous coal fines and compares results from agglomeration to the flotation response of both coals. Oil agglomeration is known to be sensitive to surface properties of coal. Since surface properties of coals depend not only on the rank of coal but also on their origin (depositional environment) and mineralogical composition, both the applicability of this new improved agglomeration process to the non-Australian coals and its efficiency became the motivation for this study. To evaluate the applicability of the new process to both Canadian bituminous and Russian sub-bituminous coals, a series of bench-scale tests were carried out under conditions similar to those described by van Netten et al. (2016) for the Australian coals. Based on the results obtained in this research, new boundary conditions for the application of the HIP emulsion-based oil agglomeration process have been outlined and conclusions on the viability of the new process to treat ultra-fine coal from Western Canada and Russian sub-bituminous coal fines have been reached.INTRODUCTION In most cases, to meet the market requirements, the mined coal has to be processed to reduce the ash content by the removal of mineral matter and thus to increase the quality of the coal products (van Netten et al., 2016). Generally, flotation is used for processing fines from high rank coals; however, there are high losses of very fine coal due to the inefficiency of this process. Furthermore, difficulty in dewatering the fine coal results in excessive moisture levels causing coal handleability issues, which increases costs in the coal-cleaning industry (Capes & Darcovich, 1984). Much of the development that has occurred in fine coal cleaning has taken place with higher-value coal, often metallurgical (Klima et al., 2012). If the fine coal is deemed to be too difficult or expensive to process, it may be discarded as waste (van Netten et al, 2014). Such disposal not only creates an environmental liability but may also result in the loss of a valuable, high quality product that is better liberated than the coarser fractions of coal."

Jan 1, 2018

By L. Burdukova

"In flotation, depressants are used to reduce the amount of gangue that reports to the concentrate and hence increase the selectivity of the flotation process. At the University of Cape Town extensive batch flotation tests are carried out to evaluate industrial depressants and standard procedures have been developed over the years.This study was conducted in order to develop an improved method for comparing depressants using machine vision as an aid. The modified method of batch flotation involved a test with prolonged intervals between scraping to allow more time for the froth to build up and mature.This method of testing showed increased differences between the flotation performance obtained as represented by grade recovery curves for carboxymethyl cellulose and guar depressants when compared to the standard method of testing with shorter scraping intervals. The improvement was attributed to reduced entrainment resulting from longer drainage time in the froth and therefore yielded a better test for comparing depressants on the basis of true gangue flotation with minimized entrainment. As expected, the sulphide recoveries were unaffected by the change in method. The machine vision system also added to the information obtained during these tests by recording bubble size trends throughout the tests which were later analyzed and related to the amount of flotable gangue in the froth. Modifications are recommended to improve the usefulness of machine vision in batch flotation."

Jan 1, 2003

By Michael. H. Moys, Clayton Bhondayi

An electro-resistive measuring technique developed by the authors was used to study the effects of superficial gas velocity and froth height on froth phase bubble sizes as a function of height above the pulp-froth interface. Flotation tests and the bubble size measurement were carried out in a laboratory mechanical flotation cell that was operated in a pseudo-steady state mode using primary rougher tailings slurry from Lonmin Platinum as feed. The values of intra-bubble impact distances (IIDs) which are the estimates for froth phase bubble sizes obtained from the measurements indicated that as superficial gas velocity was increased, the values of IIDs decreased for the two froth depths tested. Increasing froth height at fixed gas rate resulted in an increase in IID values especially close to the froth surface. Changing froth height and gas rate alters froth residence times; longer froth residence times mean more time for bubbles to coalesce hence larger values of IIDs and vice-versa.

Jan 1, 2014

By Wang Xu, Tao Dongping, Zhang Jie, Tao Youjun

Based on the principle of fly ash triboelectrification, the mineral electrical index and testing method are introduced. The electric differences of various mineral components of fly ash are discussed in view of the results of chemical and mineral composition analysis of the fly ash sample acquired from the Xin-wen power plant. The dielectric constant and charge-mass ratio of carbon and ash in the fly ash are determined. The data were then used along with the rotary triboelectrostatic separator (RTS) testing results to investigate the charging characteristic of fly ash particles in different sizes. The results show that the dielectric constant of fly ash with different particle size decreased with the decrease in particle size, which led to a poor electrical conductivity. Thus particle size has an important effect on conductivity. The charges of carbon and ash particles increased with decreasing particle size. The charge-mass ratio of carbon and ash particles of the same size increased with decreasing particle size. This indicates that finer particle size is more favorable for triboelectrification separation from the charging efficiency point of view. The rotary triboelectrostatic fly ash separation tests show that the best decarbonization performance was achieved with particles in the size range of 0.038-0.074mm with which the decarbonization rate and efficiency index reached 38.93% and 120.83% spectively.

Jan 1, 2014

By Genrich A. Denisov

Principles of ecologically friendly geo-technologies construction are formulated on the basis of the works of the leading scientists in the field of rational processing of mineral resources of the Russian Academy of Sciences. One of these concepts is a new direction in rotational disintegration of mineral and technogenic raw material with the purpose of effective subsequent enrichment. A large amount of practical experience has been accumulated in the industry on selective destruction by application of vibrational method on initial material with consideration of its physical-mechanical properties and mineral structure. This method is successfully realised in a conic inertial pulverisation devices constructed by Mekhanobr Institute (St. Petersburg). A new construction of conical-inertial pulverisation with a modification of disintegration force has been developed recently at Mekhanobr Institute. It allows, in some cases, to increase selectivity of subdivision and to avoid over-disintegration. Advantages of “wet” subdivision methods in conic inertial disintegration devices are proved. The efficiency of such subdivision can be increased due to rational use of the phenomenon of a dislocation-dynamic diffusion. Its advantage is proved by the effect on disintegrated material by frequency-modulated variable electrical fields of low power. It was shown in industrial conditions, that the productivity of the spherical mill can be increased by 10 %, and that it also prevents ecologically harmful surface active substances (SAS) in milling zone and it reduces the dust content in the air. The techniques of tentative estimation of efficiency of various proceedings technogenic materials and their classification are created. The scientific fundaments of rational, ecologically friendly technology of processing and regeneration of various kinds of technogenic raw material are developed. A number of effective technologies on processing of wastes is developed and inculcated in concentration factories and metallurgical factories.

Jan 1, 2003

By Chuanyao Sun, Yang Yu, Zhen Guo Song, Wei. Ming’An

"Carbonate minerals are very important mineral source of extracting metal, radioactive element and rare earth elements. Furthermore,some carbonate minerals, such as calcite and dolomite, are common and important components of sediments and sedimentary rocks. Many flotation processes involve the separation of valuable minerals with carbonate minerals. So it is of great significance to the flotation theory and industrial practice to investigate the flotation behaviors of carbonate minerals. As regulators, metal ions play a major role in minerals flotation. The study of influence law of metal ions on minerals flotation is helpful to eliminate or utilize the effect of metal ions. In this study, calcite and smithsonite laboratory scale flotation, surface analysis and zeta potential determination in the presence of Fe(II) ion were performed to investigate the effect of Fe(II) on carbonate flotation. The results show that Fe(?) depresses the flotation of calcite and smithsonite. The depression effect of Fe species on calcite and calamine flotation can be improved with the increase of Fe(?) concentration. The zeta potential measurements and surface analysis show the existence of iron hydroxide products on mineral surface, which may be link to carbonate site instead of exchanging with calcium on the mineral surface. Fe species on the mineral surface inhibit the interaction between the reagents and calcite/smithsonite through the formation of surface precipitation coating on the calcite/smithsonite surface when the Fe(?) concentration is higher."

Jan 1, 2014

By S. Narra

The importance of bio-products production is enhanced with the abundance and renewability of ligno- cellulosic biomass in comparison to the depleting fossil fuels especially in producing environment friendly energy. Lignin is obtained as a sludge residue from the pulp and paper industries as well as from the bio- ethanol /bio-gas production plants. Lignin is a renewable fuel with a high heating value equivalent to anthracite coal, low ash content and hydrophobic properties. The extracted lignin in paper and pulp mills is usually burnt at the mill directly to cover the energy production costs of the mill. The efficient utilization of lignin can reduce the percentage of lignin sludge used for energy production in comparison to the present situation. Presently the lignin is burnt /incinerated as sludge with minimum of 30 to 50 % moisture content. This high moisture content reduces the energy efficiency and simultaneously utilizes more amount of lignin sludge in producing the required energy. This paper explains a possibility of integrating sludge-pelleting techniques in paper and pulp mills. The integrated sludge-pelleting techniques would lead to an optimal utilization of lignin for energy and would simultaneously save the lignin resource for material utilization. The sludge pelleting process solves also the problem of handling, storage and explosion risks of lignin when compared to the present situation.

Sep 1, 2012

By Erico Tabosa, Meng. Jun, Kym Runge, Matthew Brennan, Weiguo Xie, Dee Bradshaw

Turbulence and its distribution are of great importance in flotation cell design as they affect suspension of particles, air dispersion and particle-bubble collision rates, which in turn determine flotation performance. However, there is no mature technique to measure turbulence in three phase (liquid-solid-gas) systems such as in flotation cells. In this article, the authors present two new approaches that are suitable for measuring turbulence distribution in three phase systems and validate their applicability. The first technique uses a piezoelectric vibration sensor (PVS) to measure fluid kinetic energy standard deviation and the second technique applies electrical resistance tomography (ERT) to measure conductivity variation at a measurement position in a flotation cell. For the PVS technique, calibration of the sensor was performed to determine the values of parameters that were needed to calculate the force applied to the sensor. Then measurement was conducted in a 60L batch flotation cell and the results were compared with LDA measurement. This demonstrated that the piezoelectric sensor signal provides a good representation of fluid kinetic energy standard deviation at the position of measurement. For the ERT technique, conductivity distribution data was processed to give conductivity variations, which were then used to calculate fluid kinetic energy standard deviation at the measurement position. The spatial distribution of turbulence obtained by performing multiple measurements at different positions in the 60 litre batch flotation cell was found to agree with the PVS measurement results. These two techniques are potentially powerful tools for turbulence measurement in flotation environments, enabling a clearer understanding of turbulence’s influence on flotation performance to be determined.

Jan 1, 2014

By E. Ashirbaeva

"Ores of ferrous metals traditionally make up the bulk of recoverable reserves of solid minerals, and iron ore concentrates - in the processing and consumption. To obtain concentrates, three main methods are used: dry and wet magnetic separation, gravity and flotation. But even their integration into complex developed schemes with finishing operations often do not solve the problem of obtaining high-quality concentrates, which are necessary for powder metallurgy and electric steelmaking. Increasing the iron content in the concentrate by removing harmful impurities is the goal of this work. The possibility of reducing the operations of wet magnetic separation twice and completely eliminating concentrating operations in ball mills from the scheme of operations has been established. Selective leaching agents for each type of iron ores have been created, allowing to obtain concentrates with an iron content of not less than 68-69% and negligible concentrations of harmful impurities. Methodical recommendations for long-term storage of bioreagents in the active state, their immobilization and preparation in industrial conditions at the enterprise Nedropolzovatelja are developed. The proposed biotechnology, which allows to obtain high quality iron and conditional concentrates for harmful impurities, is protected by patents (RU 2537684 ""Method for fine-tuning of high-sulfur magnetite concentrate"" for magnetite ores and Pat. RU 2599068. For the industrial implementation of the new technology, organizational and technological measures have been developed in the system with Road maps for types of ores. The developed technology makes it possible to condition noble metal, tin, tungsten, nickel and other concentrates in harmful impurities such as arsenic, antimony, mercury, sulfur, copper, zinc, iron, phosphorus, manganese, in total 30 components that pass into solution under the influence of bioreagents.INTRODUCTION Consumption of various metals is steadily increasing every year, the volume of mining is constantly increasing. Ores of ferrous metals traditionally make up the bulk of the recoverable reserves of solid minerals. Enrichment technologies for iron-containing ores are reduced to the combination of three main methods: wet and dry magnetic separation, gravity and flotation. But even the use of complex advanced technological schemes often does not lead to the production of high-quality concentrates suitable for metallurgical processing. In this case, either lapping operations or effective technical and technological solutions are used in the main enrichment cycle. Widely used in practice methods for improving the quality of iron ore concentrates include the use of finishing operations (fine screening, reverse cation flotation), staging of concentrates, the use of more sophisticated equipment (separators with running magnetic field, magnetic gravity classifiers, column flotation machines)."

Jan 1, 2018

By F. Henríquez

Traditionally, the implementation of an automated control for a ball mill has been a challenging one. First, it must be capable of processing a variable SAG mill feed while at the same time avoiding to become a process bottle neck. Second thing is, it must deliver an adequate quality product (P80) to the process downstream. Then the ball mill itself and its associated classification equipment has problems of its own: it must maintain adequate control of cyclone?s pressure, density and pump-box level with often, less manipulated variables than needed, namely, variable pump speed and the opening/closing of cyclones. Thus, it becomes a non-linear multi-variable type of process with often too multiple and contradictory control objectives to satisfy simultaneously. On top of that, to extend cyclones availability and yet, maintaining their performance, is must both for process and maintenance purposes. Trying to solve the puzzle, Minera Los Pelambres implemented a novel and successful combination of MPC (Multivariable Predictive Control) and advanced control in two of its newest ball mills, reducing considerably process variability while maintaining high throughput and keeping the process well within constraints limits. Because of their differences in processing capacity, size and topology, two different stabilizing-control strategies were developed, tested and tuned. Hence, for both control approaches their implementation process, main results, areas of applicability, limitations and their key performance indicators are discussed further. This paper also discusses the need of such advance control technologies in the mining industry, including the impact of these technologies on best practices for their implementation, operation and long term sustainability

Sep 1, 2012

By Rob Morrison, Andrew Scott

"Long before a modern mine commences operations it has already become a wealth of information. After start up, it can generate enormous quantities of data - especially with semi-automated data acquisition by instrumented mine equipment.However, much of this data is of limited use for evaluation of (potential) performance unless it links in some way to the site business model.An underlying reason for this waste of data is that the different cultures, financial, technical, community, environmental, etc, not only have many areas of interest but also have very different conceptual models by which they evaluate performance.It is too ambitious to attempt to bring all of these cultures together - in a single step.However, the success of the Mine to Mill - project has demonstrated that substantial operational value can be added by using a more integrated approach to comminution. The next logical step is to integrate measurement and then to track performance from ore body model to saleable product and waste disposal. From resource to product also represents a path from very sparse, highly variable data to much more detailed measurement and more representative sampling.However, in both cases the data collected is strongly focused on the technical requirements - not on the business model.This paper considers how to define at least some of the key decision points in terms of some case studies.Performance data from many areas might be used to derive simple models which can then be used for forecasting and optimisation of planning."

Jan 1, 2003

By Gregory Harbort, Sarah K. DeBono, Alan J. Monaghan, Emmanual V. Manlapig

"The Jameson Cell is a type of flotation machine in which air and pulp are brought together in a vertical tube called a downcomer. Within the downcomer the air and pulp are dispersed into a dense foam of fine bubbles, which creates a favourable environment for bubble-particle collision and subsequent collection of hydrophobic particles. The intense collection zone within the downcomer can be considered similar to the zone between the rotor and stator in mechanical flotation cells.Research into the bubble-particle collision and fluid dynamics of mechanical cells rotor-stator zone has been limited by the difficulty of achieving accurate measurements in production sized machines. With the Jameson Cell the downcomer is largely external and separated from the flotation tank, allowing ready access to the primary contacting zone for measurement and analysis.An investigation has been undertaken into the operating characteristics of the downcomer relating to bubble-particle collision. An effective mapping of the downcomer has been made through measurements of void fraction and bubble size taken across cross sections of the downcomer. Analysis of these measurements has provided an interpretation of the variations in the air and fluid dynamics, bubble size and distribution throughout the downcomer chamber.Existing models of bubble-particle collision efficiency are reviewed in respect to the collected information and refinements conducted. The area of maximum bubble-particle collision efficiency is defined. Findings are related to operation within the rotor-stator zone of mechanical flotation cells."

Jan 1, 2003

By P. Harris, D Bradshaw

"Comparison of the two most commonly used classes of depressant in the South African platinum industry is complicated by the fact that these polymers induce different effects on the surfaces onto which they adsorb. The use of carboxymethyl cellulose (CMC), which is ionically charged in solution, can lead to increased particle dispersion in addition to the effect of reduced surface hydrophobicity (depression). Guar is typically only slightly charged in solution. Comparison of these two depressants is complicated since it is uncertain whether differences in their action is a result of either depression of dispersion effects.This work investigates the role of dispersion independently to that of depression in the batch flotation of a platinum bearing ore. An inorganic dispersant, sodium hexametaphosphate (NaHMP) was added in parallel to the uncharged guar depressant to simulate the action of depressants with varying degrees of dispersion. By distinguishing between the material recovered by entrainment and the floatable gangue and by including the effects of froth stability it was possible to decouple the effects of dispersion and depression.The results show that both dispersion and depression led to increased grade of the sulphide minerals. Depression leads to a decreased recovery of floatable gangue minerals. Dispersion leads to an increased recovery rate of these minerals and an accompanying decrease in froth stability."

Jan 1, 2003