Search Documents

By M. Mirnezami

Pentlandite samples were obtained as Ni concentrate from three Canadian plants and one specimen sample from Ward?s Scientific Establishment. The samples were upgraded using gravity and magnetic separation techniques. Nickel concentration was determined by atomic absorption spectroscopy. Microprobe analysis identified a range in Co and Cu lattice substitutions. All samples exhibited similar zeta potential-pH trend with isoelectric points from 2 to 3, and similar responses to copper activation and addition of xanthate. The similar trends indicate that the variations in lattice substitution identified have no significant effect on electrokinetic properties; that is, samples from any source likely yield results that can be generalized.

Sep 1, 2012

By S. M. Bradshaw, C. Dorfling, F. Ngandu

"Selenium removal and platinum group metal (PGM) recovery from copper sulfate leach solutions form an integral part of platinum producers’ base metal refinery operations. Recent studies found that substantially higher PGM recoveries can be achieved if excess thiourea instead of sulfurous acid is used as precipitation reagent; however, the impact of the proposed process on downstream processes was unknown. The objective of the current study was therefore to investigate the effects that excess thiourea and residual selenium present in the rich copper sulfate electrolyte have on copper electrowinning. This was achieved by performing cyclic voltammetry tests using a platinum rotating disk as working electrode, a graphite auxiliary electrode and a saturated calomel reference electrode. A synthetic copper sulfate electrolyte containing 0.01 M Cu2+, 1 M H2SO4 and varying amounts of selenium (20 – 150 mg/L) and thiourea (10 mg/L and 100 – 300 % excess) was used. The results obtained have shown that both thiourea and selenium interact with the cupric ion cathodic reduction reaction. Thiourea polarized the working electrode and lowered the efficiency of the cupric reduction reaction. Tests on the solutions with high selenium concentration showed simultaneous reduction of copper and selenium, which led to copper selenide formation. Nodule formation on the deposit surface also became significant at higher selenium concentrations. Based on these results, it was concluded that precipitation of PGMs from the copper sulfate solution with excess thiourea is not feasible due to the detrimental effect on downstream electrowinning operations.INTRODUCTION During the high pressure oxidative leaching stage in a typical base metal refinery (BMR) circuit, selenium, tellurium and some platinum group metals (PGMs) are dissolved along with the desired copper ions. The impurities (selenium and tellurium) may pass to the copper electrowinning circuit where it can result in the formation of nodular copper electrodeposits or reduced current efficiency. The presence of PGMs in solution, on the other hand, increases the precious metal inventory and potential losses of the operation. Currently, sulfurous acid is widely used for selenium and tellurium precipitation from copper sulfate leach solutions. Sulfurous acid is capable of reducing cupric ions to cuprous ions; the generated cuprous ions then react with Se4+ and Se6+ to precipitate selenium as a copper selenide (Bello, Dorfling, 2014). Recent studies have, however, proposed the use of excess thiourea as a precipitating agent for the removal of selenium and tellurium; it has the advantage of improved PGM recovery in the Se/Te precipitation step (Lottering, Eksteen et al., 2012; Mulwanda, Dorfling, 2015)."

Jan 1, 2018

By Anuttam Patra, Romain Bordes, Andreas Fredriksson, Tommy Karlkvist, Krister Holmberg, Kota Hanumantha Rao

The present investigation aims to develop and distinguish mineral specific reagents with two functional groups for use in flotation of calcium containing minerals. For this purpose, a series of dicarboxylate-based surfactants with varying length between the carboxylate groups (one, two or three methylene groups) were synthesized. As reference, a surfactant with the same alkyl chain length but with only one carboxylate group in the polar part was synthesized. The adsorption behavior of these new reagents on pure apatite and calcite mineral surfaces was studied using Hallimond tube flotation, FTIR and ? potential measurements. The relation between the adsorption behavior of a given surfactant on a specific mineral surface and its molecular structure over a range of concentration and pH values, as well as the region of maximum recovery were established. It was found that one of the reagents, with a specific distance between the carboxylate groups, was much more selective for a particular mineral surface than the other homologues synthesized. This selective adsorption of a given surfactant to a particular mineral surface relative to other mineral surfaces as evidenced in flotation studies is substantiated by ? potential and infra-red spectroscopy data.

Jan 1, 2014

By David I. Verrelli, Boris Albijanic

"Froth flotation is an exceedingly complex physicochemical process. The convenience of distilling much of the complexity of the bubble-particle interactions into a single parameter has led to the continuing popularity of the classical ‘induction time’ to quantify the threshold for bubble-particle attachment to occur. Despite this popularity and the simplicity of the concept, there is no single universal method of evaluating the induction period. In this paper, we begin with a critical review of the available techniques for estimating the induction period. These are: back-calculation from experimental (micro) flotation tests; pushing a particle toward a stationary bubble (or vice versa) using an atomic force microscope (AFM); pushing a bubble toward a stationary bed of particles in the ‘Induction Timer’; pushing a bubble toward a stationary solid surface using the ‘integrated thin film drainage apparatus’ (ITFDA); and dropping particles onto a submerged stationary bubble using the ‘Milli-Timer’ device. Each one of these methods has advantages and disadvantages, and the best choice depends on the application. In the experimental section, we present quantitative comparison of the induction periods estimated using two different techniques, namely the Induction Timer and the Milli-Timer. The same particles were tested in each device, under the same conditions. It was found that by tuning the operation of the particle pick-up device, similar estimates of induction period could be obtained to the estimates made by direct observation with the Milli-Timer. In the former device a bubble is driven toward a particle bed at a controlled rate, whereas in the latter a particle’s motion is governed by the hydrodynamics. The potential to match these presents an intriguing prospect for better understanding the bubble-particle interaction, and the possibility to ‘calibrate’ the simpler Induction Timer against direct observations."

Jan 1, 2014

By Katarina Theander, Robert J. Pugh

The generation of froth with a critical degree of stability and height is an important aspect of the froth flotation. In this paper we have studied the synergism and anti-synergism in frothing behaviour in a mixed flotation collector/frother mixture (a model fatty acid; sodium oleate and a model frother; nonionic (polyethyleneoxide alkyl C14E6). Values of the collector / frother molecular interaction parameters (the ß-parameters) were determined from the surface tension data using regular solution theory. The frothing characteristics of the system were evaluated using a glass column equipped with a series of conductivity electrodes, which enabled the water content of the froth to be determined. From these measurements, the dynamic frothability and static froth stability were determined. It was concluded that the synergism/anti-synergism in frothability was depended on the molecular composition of the surfactant system, the diffusion of monomer to the thin film interface and on the breakdown of the mixed nonionic/anionic micelles.

Jan 1, 2003

By Paul W. Weiblen, Louis J. Cabri, Rolando Lastra

"Preliminary tests were done to determine whether comminution by electric-pulse disaggregation, or E-PD (cf. Rudashevsky et al; 1995), was more effective than using conventional crushing for Merensky Reef ore. A hand sample of the Merensky Reef was sawn in two: then one sub-sample was comminuted to .2 mm using E-PD at the University of Minnesota, and the other sub-sample was crushed to .2 mm using a conventional jaw crusher at CANMET.The products of the electric-pulse disaggregation and jaw crusher were fractionated by sieving and by a separation using a heavy liquid with a specific gravity of 3.3, because the proportion of platinum-group minerals (PGM) and sulphides to silicate minerals is very low. Thus, four mineral separates were produced: .2000 + 833 µm, -833 +208 µm, -208-µm float and -208-µm sink. All the mineral separates were studied by image analysis (Lastra et al; 1998). The main objective was to determine the liberation of gangue (silicate minerals), chromite, pyrrhotite, chalcopyrite, pentlandite and PGM. In the case of the PGM, a specific image analysis program was written to search and measure these minerals.The results show that the liberation obtained for gangue was similar (~99%) using either method of comminution. However, the liberation obtained for chromite (~89% vs. ~38%), pentlandite (~50% vs. 1%), pyrrhotite (~56% vs. ~38%), and PGM (~56% vs. ~1%) by E-PD was higher than that obtained by conventional jaw crusher, whereas the liberation obtained for chalcopyrite (~20% vs. ~71%) by E-PD was lower. Nevertheless, the image analysis of the products also showed that the PGM are strongly associated with pentlandite. Thus, for the Merensky Reef, liberation of pentlandite from the gangue minerals and chromite is important to recover more of the PGM. This maybe be significant because, in addition to increased recovery of platinum-group minerals (PGM), Merensky Reef pentlandite also contains significant quantities of valuable platinum-group elements like Pd and Rh (Cabri, 1981; Cabri 1988, Kinloch 1982, Peyerl 1983). Hence, the results indicate that for the Merensky Reef, electric-pulse disaggregation would represent a better comminution operation than a conventional jaw crusher would. In addition, the greatly improved liberation for chromite may find application for the PGM-rich UG2 chromitite."

Jan 1, 2003

By Vladimir F. Skorokhodov, Nikolay N. Melnikov, Svetlana P. Mesyats

"Among the problems of the civilization development, a problem of interaction between man and natural environment can be highlighted. In the twentieth century the human transforming activity had got scales of geological processes and defined the contradiction between the goal to increase the quality of human life and possibilities of the natural environment. Last twenty-five years after the World Summit on the Environment (1992) indicate that the development of civilization is still based on receiving super profits from the natural resources exploitation. This statement is confirmed by economy globalization rates, growing contradictions between consumption and production, depletion and degradation natural environment. A new technological order is formed at the time of growing world population, technological capacities, organizational complexity, from one side, and global scales of geo-resources consumption, on the other side. Sciences, determining the further civilization development, should take on the task to change the social worldview, since the preservation of human population consists in remediating and maintenance of biosphere functions as a regulator of ecological balance. The new worldview in the geo-resources exploitation is based on the Ecological strategy of mining development, which consists in reducing mining-induced loading on natural environment while increasing efficient mineral production and processing, and providing for a comprehensive solution of tasks on mineral deposit development. One of strategic trend of mining development is to increase complexity and completeness of useful component extraction from ore and mining deposits while reducing wastes and decreasing their stockpiled volumes. The implementation of the ecological strategy has shown that the future is determined by reduction of the environmental impact while improving the efficiency of mineral mining and processing.INTRODUCTION The global nature of environmental problems caused by the scale of consumption of natural resources, huge amounts of waste, and intensive man-made impact on the environment requires a revision of the strategy for the natural resources development. Many existing technologies are ineffective in achieving the ultimate goal. Direct output in the raw materials - the end product technological chain rarely exceeds 10%, which implies a huge amount of work to move the soil. In addition, the feature of scientific and technological progress at the present stage is the growth of power-to-weight ratio."

Jan 1, 2018

By Gaurav Soni, Roe-Hoan Yoon

A first principle flotation model has been derived from the basic mechanisms involved in flotation. The model consists of a series of analytical equations for bubble generation, bubble-particle collision, attachment, detachment, and froth phase recovery. The model can predict flotation from both hydrodynamic and surface chemistry parameters such as bubble size, particle size, energy dissipation rate, ?-potentials, contact angles (?), etc. The model predictions have been compared with the results of a series of laboratory flotation tests conducted using mono-sized glass beads of different particle sizes and contact angles under different operating conditions. Some of the experiments were conducted using a 1:9 mixtures if hydrophobic silica and hydrophilic magnetite, so that the product graded could be readily determined by simple magnetic separation. The model predictions are in good agreement with the experimental results both in recovery and grade. A computer simulator developed on the basis of the model is capable of designing a preliminary flotation circuit on the basis of feed characteristics, e.g., size-by-liberation data, and the hydrodynamic information on the flotation cells to be incorporated in the circuit.

Jan 1, 2014

By Marina Nicolova, Irena Spasova, Plamen Georgiev, Stoyan Groudev

Different strains of "silicate" bacteria were used to improve the quality of kaolin by different ways of treatment. All strains formed large slimy capsules consisting of exopolysaccharides and were related to different species of the genus Bacillus, mainly to B. circulans and B. mucilaginosus. It was found that even a short contact of some hours of well developed cultures of these bacteria resulted in improvement of the bending strength and the other ceramic properties of the kaolin. The improvement was connected with the action of some secreted microbial metabolites such as soluble heteropolysccharides, monosugars and organic acids. The best results were achieved by continuous cultivation of bacteria in the presence of kaolin with a high relative humidity and subjected to periodic stirring.

Jan 1, 2014

By Milind Chikhale, Yogesh Reja, Keshav Tyagi

"Using computer models for process design is a well-established practice in the mineral industry. In recent years, there has been emphasis on modeling of processing plant as a whole. This paper covers development of a model for iron ore processing plant. Basic purpose of this model is to use simulation for efficient plant design and help in minimizing risk at the very initial stage of project. Feed to the plant is Hematite iron ore from a deposit located in Eastern India. Major processes in plant include multi-stage crushing, screening, grinding, classification, gravity and magnetic separation. Models for different process equipment were developed using METSIM and Bruno simulation software. Customized black box models and known mathematical models were used for predicting behaviour of processes. Data needed was identified based on the model type. The required data was arranged as per project requirement and processed for development and validation of model. Equipment models were developed and validated on the basis of process design basis, theoretical and empirical data from technical references, and bench scale and pilot scale testwork results. Validated process circuits were assembled to simulate and represent the entire plant process. The result shows expected variation in plant output as a result of variation in the feed. Study concludes by discussing potential applications of the model in plant design."

Jan 1, 2014

Geopolymers are novel engineering materials with the potential to play a highly significant role in the transformation of the construction materials and building products industry in the push to-wards sustainable development. These materials are formed by activation of industrial aluminosilicate waste materials such as coal ash or blast furnace slag with alkaline solutions. Some mineral waste can also be used, either as fillers or as reactive components. The use of waste-based geopolymers results in significant (up to 90%) reduction in carbon dioxide emissions when used in cement replacement applications. In addition to the formation of conventional pre-cast products, these high performance mineral binders are ideally suited to use in the conversion or encapsulation of toxic waste, including radioactive waste, due to their chemical stability and resistance to acid attack. It is the aim of this paper to review recent developments on the science underpinning this ?green? technology, and to discuss the technical and commercial drivers governing the large-scale adoption of the technology. Some of the recent fundamental breakthroughs in the study of geopolymer technology at the University of Melbourne will be presented. Despite the complexity of this reactive sol-id-gel system, progress has been made in the development of a thermochemical reaction kinetic model that has been validated using both calorimetric data and synchrotron kinetic data. Geopolymerization is potentially a disruptive technology, so that it is normal to expect strong resistance from established companies in the construction materials industry. It is increasingly necessary that waste generating industries such as mining collaborate with industries such as construction that could utilize this waste. The world?s first full scale geopolymer plant utilizing waste and re-cycled material has been commissioned recently in Melbourne, Australia, so progress on commercialization will also be presented. The authors frequently present keynote lectures on geopolymer science and technology at materials science, ceramics and construction materials conferences. However, this interdisciplinary technology that is still in its infancy, deserves more attention in the mineral processing and mining industry in view of its potential use in the mining industry, and also in view of the importance of mineral processing techniques in recent advances in geopolymers.

Jan 1, 2014

By D. W. Fuerstenau

Understanding how cationic surfactants affect the interfacial behavior of quartz is important in mineral processing and environmental engineering. This paper presents the results of a study of the effect of the molecular structure of cationic surfactants on the interfacial behavior of finely ground natural quartz. Most of the experimental work involved the determination of zeta potentials and the stability of quartz suspensions. Some measurements of induction times and the flotation response of coarser particles are also included. How these surfactants affect interfacial behavior is discussed in terms of adsorption mechanisms. The molecular structure (number of hydrocarbon chains, type of ionic head group, number of ionic head groups on the molecule) of these reagents was found to significantly affect their surface activity.

Jan 1, 2014

By Megan Becker, Cyril O’Connor, Jenny Wiese, Gaynor Yorath

The effect of particle shape on true flotation has been widely reported. The present paper presents results obtained in investigating the effect of particle shape on the entrainment of particles during the flotation process. Different hydrophilic minerals with particles of varying aspect ratios were used and their shape determined using rheological tests and QEMSCAN. Their entrainment properties showed a close relationship to their shape with the recovery due to entrainment increasing as the aspect ratio of the particles increased. The effect of surface charge, by changing pH, and size of particles showed that the effect of shape was sustained at different pHs and particle sizes. Proposals are made to explain these observations in terms of the known relationships between drag coefficients and terminal velocities and shape. Since it has been previously reported that different milling procedures can affect particle shape, these results indicate that it is possible that such different procedures may result in increased entrainment of hydrophilic minerals.

Jan 1, 2014

By S. Narra

Converting biomass into valuable fuel requires various preprocessing of the raw materials. Biomass densification is one of the conversion processes for its utilization. The aim of densification is to produce biomass pellets, which can withstand regular handling stresses and exhibit high densities with uniform size and shape. Physical properties, such as the particle size distribution after comminution is of highest importance for the binding mechanisms in the pelletisation process. Durability and strength of the pellets play an important role indicating the ability to withstand handling stresses. Particle size distributions of the cereal straws (Rye and Wheat) after specific comminution and liberation processes have been carried out with the help of three different image analysis (Microscope, Camsizer and Fibreshape). The durability of the pellets have been investigated as specified in the standards (ASAE standard S269.4) with a quadratic crate and the strength of the pellets with compression and tension testing machine (Zwick Roell type: ZMART.PRO). The particles size results showed differences in both length and width after different comminution processing. An exact comparison between the particle size analyses with the three different image analyses was not possible. The particle size distribution and the different comminution processes displayed influences on the durability and strength of the produced pellets. The particle size distribution displayed approximately 40 % of fines and 60 % of fibers. The particle size distribution displayed a direct relation to the durability of the pellets. Further durability and strength of the pellets displayed a good correlation.

Sep 1, 2012

By Gülay Bulut, Ünzile Yenial

"Water composition has a significant effect on flotation. A better understand the role of water composition in flotation is very important for process quality and performance. Based on source of process water, the concentrations of the dissolved ions, hardness, contaminants and residual composition of reagents can varied in the process water. The various water resources employed during lead and zinc flotation caused activation, depression or selectivity effects on minerals due to the presence of different ions in solution. Metal ions in these water resources were adsorbed on the ore, whilst ions associated with gangue minerals were released into the flotation pulp.This paper includes a research for the effect of different water compositions on lead and zinc sulphide flotation. Experiments were carried out five types of water such as tap water, recycling water, tailing dam water, underground mine water and sea water. The ore sample was obtained from Esan Balikesir-Balya mine. The mineralogical study of ore sample shows that it contains mainly galena, sphalerite, pyrite, hematite, quartz, diopside, epidote, calcite, and chlorite. It is found that recycling water and tailing dam water has a positive effect on recovery of lead and zinc minerals and detrimental effect on content of both minerals. This result may explain with remaining reagents in these waters. Underground mine water and tap water gave nearly the same recoveries of zinc. Sea water affects the recovery lead and zinc negatively."

Jan 1, 2014

By Seungwoo Park, Gaurav Soni, Roe-Hoan Yoon, Hyunsun Do, Kaiwu Huang

In a flotation froth (and foam), air bubbles become larger due to coalescence, causing bubble size to increase, bubble surface area to decrease, and hence casing less hydrophobic particles to drop off to the pulp phase below. Thus, bubble coarsening provides an important mechanism by which product grades are increased. On the other hand, excessive bubble coarsening results in low recoveries. In the present work, a model describing the process of bubbles becoming coarser in a foam as they rise to the top by deriving a mathematical relation between the Plateau border area, which controls film drainage rate, and the lamella film thickness, which controls bubble-coalescence rate. The model has been derived by assuming that liquid drainage rate increases due to slip at the air/water interface, and that the critical rupture thickness is determined by the capillary waves created by thermal motion. The model developed in the present work can predict the bubble size ratio between the top and bottom of a foam as functions of aeration rate, foam height, and surface tension (frother dosage). The model predictions are in good agreement with the changes in bubble sizes measured using a high-speed camera.

Jan 1, 2014

By Heiko Schiemann, Christoph Beyer, Thomas Pretz

"Due to multiple experiences in the field of planning and engineering of processing plants for secondary materials the Chair for Processing and Recycling of Solid Waste Materials decided to develop a software tool that supports the engineering and the planning of the basic layout of processing plants for secondary material flows. The detailed description of the material flow and its characteristic parameters is one of the main tasks to be worked out and should be considered as the basis for representative simulation results.The description of the material flow and its characteristic parameters is based on a fraction vector containing 12 material fractions. This is a compromise between a detailed material flow description and a compact and therefore time-extensive calculation model. Each material fraction is characterized by 15 parameters, which can be edited with the help of an easily accessible user-interface. In addition to basic parameters like ignition loss, water content and calorific value more parameters like the material fraction-specific particle-size distribution are contained. Using the model library SimuRec, the processing success and the recovery of complex processing plants for secondary materials can be predicted."

Jan 1, 2003

By Fedotov Pavel

"Today the main objective of improving the process of ore dressing is to reduce energy consumption and performance of the basic rule of auxiliary enrichment processes. One of the modern means of ore destruction with a minimum of energy consumption is the interparticle fracturing, for example in the roller press. There still remain the unsolved problems of the energy consumption determination and the particle size distribution of the crushing product .Existing methods for determining these parameters are empirical and require considerable expenses and time. The improved finite element was developed to solve these problems using finite element contact interaction of the rock. Also it was developed to clarify the stress-strain and the rock fracture energy in a layer. These elements are used to study ore destruction in the layer and allows to create a model taking into account the interaction of crushing particles surfaces. The same algorithm was developed determining crushing product particle size distribution in the layer on the base of the Bond’s theory of crushing. The presented finite element model allows to determine the quantity of strain energy and particle size distribution of crushed product during the destruction processes of the material in the roller press with fair accuracy."

Jan 1, 2014

By I. Gombköto

Mining and mineral processing operations are usually generating huge amount of tailings. These tailings often gives lots of maintenance work in order to protect environmental resources from heavy metals slowly leaching out of tailing are due to Acid Rock Drainage (ARD) process. Handling leakage could be active or passive such as using of Permeable Reactive Barriers (PRB). PRB?s are used worldwide treating underground contaminations, using different type of matrix materials. All generally used matrix material has its advantages and disadvantages such as selectivity, sensitivity of precipitation generation or not satisfying hydraulic conductivity. Nowadays cheap and effective matrix material which is ignorant to pore plugging caused by precipitation within the PRB could be one solution to the demands of the industry. The authors have been carried out an investigation at University of Miskolc on lignite as high humid acid containing material for determining the ability of heavy metal adsorption and pore plugging resistance. Moreover, using hydraulic and chemical simulation methods, complete PRB dimensioning protocol based on new lignite matrix had been introduced. Within the frame of this paper the results are going to be discussed.

Sep 1, 2012

By S. Nitta

The present study deals with a new approach in calculating the size of Tower Mills. The method is derived from the application of grinding kinetics theory on the analysis of by-gone operational data. It requires only information on the capacity of the mill to be designed, the product fineness and the Bond?s work index to give an accurate and simple prediction of Tower Mill characteristics. An example illustrates the different steps of calculation.

Jan 1, 2014