Search Documents

By Igor E. Mikhaltsev

This paper concerns the continuation of work on the deepwater non-oxygen cycle heat energy generating systems. The 25-kW prototype of a universal deepwater turbine-electric energy source with hydrazine-hydrate as the primary heat production chemical is described in short and its abilities are discussed. The ?hydrazine-hydrate 64? is a catalytically dissociated heat production chemical (H2H4 ? nH2O) with 36% of water. The system was designed for work in any depths of the ocean down to 6000 m. It was built and tested working in the testing chamber in the ambient hydrostatic pressure of 600 bar. Then it was tested in the autonomous programmed regime in the Atlantic Ocean. The privileges of that energy system for any bottom installations or moving devices designed for ocean mining which need high power energy sources (20-100 kW and more) are discussed. The important needed step forward is raising the efficiency of the system which needs some investigation work in known directions. It is supposed that the possibility of getting about 5 kg/kWh with improved battery charging possibilities could be achieved. This might make the system even more profitable for mining operations.

Jan 1, 2001

By Cornel E. J. de Ronde

Brothers volcano (34°51.7?S, 179°03.6?E) is a large caldera volcano that forms part of the active Kermadec arc south of 32° S, NE of New Zealand. It is an elongate edifice striking NW-SE that is ~11-13 km long by 7-8 km across. The caldera has a basal diameter of 3-3.5 km and is surrounded by 350-450 m high walls with the floor 1,850 m deep. A volcanic cone of dacite composition rises 350 m from the caldera floor and partially coalesces with the southern caldera wall. Much of the caldera construction and the location of the hydrothermal vent sites are controlled by intersecting basement structures. Three hydrothermal sites have been recognized at Brothers; NW caldera, SE caldera and cone. Multiple hydrothermal plumes were mapped from the bottom of the caldera upwards to a depth of 900 m and originate from two of the sites; one on the NW caldera wall the other atop the cone. Analyses of these plumes show that the two vent sites are chemically distinct. The cone site itself hosts three distinct vent fields (summit, upper flank, NE flank) that in 1999 had plumes (mainly from the summit) containing relatively high concentrations of gas with a shift of -0.27 pH units (proxy for CO2) and H2S concentrations up to 4,250 nM, particulate Cu (PCu) of 3.4 nM, total dissolvable Fe (TDFe) of 4,720 nM, TDMn up to 260 nM and Fe/Mn values between 4.4 and 18.2. However, in 2002 plumes from the summit vent field had noticeably lower concentrations of PCu (0.3 nM), TDFe (175 nM), and Fe/Mn values of 0.8, although similar TDMn (220 nM) and shift in pH (-0.22) suggesting a state of flux for this site. By contrast, plumes originating from the NW caldera site have much less gas with a pH shift of -0.09 units and no detectable H2S, TDFe up to 955 nM, TDMn up to 150 nM, and Fe/Mn values of 6.4, and have not changed their composition over the same three year interval indicating a more chronic hydrothermal system. Plume d3He results show helium is decoupled from more near-surface vent fluid sources although a shift in R/Ra values from 6.1 ± 0.5 in 1999 for the combined vent sites to 7.2 ± 0.1 in 2002 indicates a less radiogenic input of helium over three years, suggestive of a greater magmatic input to the system.

Jan 1, 2004

An extensive ferromanganese nodule field south of New Zealand (Fig. 1) has existed beneath the flow of the Deep Western Boundary Current (DWBC) and Antarctic Circumpolar Current (ACC) for at least the past 15 m.y. West of 174°E, between 59°S and 48°S, the field is 300-500 km wide, but east of 174°E, where current flow impinges on the eastern slope of the Campbell Plateau, the field narrows from ca. 200 km at 55°S to ca. 120 km at 51°S. This narrowing coincides with deflection of current flow eastwards, and consequent reduction in bottom-current velocity and eddy kinetic energy. Based on sea floor photographs, dredge samples and 3.5 kHz profile data, six distinct seafloor substrates are delineated, forming broadly parallel zones eastwards from the lowermost Campbell Slope (Fig. 2).

Jan 1, 2003

By G. Rehder

The release of methane as free gas from the seafloor into the water-column well within the hydrate stability field is a natural process observed today in various ocean settings, such as the Cascadia margin, the Black Sea, the Guayamas Basin, and the Gulf of Mexico. The subsequent dissolution of gas bubbles into the water-column determines the vertical distribution of aqueous methane in the water-column and the upwards methane flux. Understanding this process not only is essential to describing the impact of natural deep-sea gas seepage, but also to assessing the hazard potential from blowouts and offshore exploitation activities, which are steadily expanding to greater ocean depths. Furthermore, the fate of methane from seeps contributes to scenarios of global change in the past and future involving the large scale destabilization of gas hydrates on a. We recently reported on the extended lifetime of methane bubbles within the hydrate stability field due to the formation of a hydrate skin (Rehder et al., 2002), based on in situ measurements of methane and argon bubble dissolution in the depth range 400 to 800 m. More recently, these observations were extended to depths from 900 to 1500 m. Single bubbles were injected from the ROV Ventana into an attached, back-illuminated, flow-through imaging box. The ascent of individual bubbles within the imaging box was recorded with Ventana?s HDTV camera system by piloting the 3-ton ROV upward, at the bubble rise velocity, for up to 400 m of vertical transit. Observed rise velocities were approximately 30cm/sec for all depths. Post-dive analysis of the HDTV video allowed detailed measurements of the bubble shrinking rates. The results of the earlier and new experiments lead to the following conclusions: (A) Methane bubbles released below the hydrate stability field showed markedly enhanced lifetimes, attributed to hydrate skin formation. The change in radius with time, dr/dt, varied from -7.5 micrometer/s above the hydrate stability field to about -1 micrometer/s at the deepest release depth. (B) Bubble lifetime within the hydrate stability field increased with distance in P-T space from the hydrate phase boundary. (C) Before hydrate skin nucleation, dr/dt for CH4 bubbles was comparable to dr/dt above the hydrate stability field. Although variable, the onset time for the hydrate skin effect to occur generally decreased with distance from the hydrate phase boundary (super-pressurization and super-cooling with respect to hydrate formation). (D) Even before the onset of the hydrate skin effect, a slight decrease of dr/dt with increasing depth was observed.

Jan 1, 2005

By P. C. Hollick

Two marine diamond deposits on concession 2b off Namaqualand along the South African Coast, have been systematically mined over the past year by the mv Moonstar. The two deposits, Smith?s Ulcer and Wedge Point Basin, are comparable in morphology, straddled the same water depths and have similar geology yet have given very different recoveries when compared to their respective grade models. These differences are best ascribed to the different style of mineralisation observed within the two deposits which has been directly controlled by the bedrock morphology. The smith?s Ulcer deposit has been formed in a metagreywacke bedrock displaying a strong north-south trending foliation which dips steeply to the west. Consequently the mineralisation is confined to narrow north-south linear trends with limited lateral extent (less than 5m) making extraction extremely difficult and somewhat variable. RE factors (recovered grade versus estimated grade) for this deposit range from 0.5 to 1.1. The Wedge Point Basin deposit is formed in a micaceous metaquartzite with a conjugate southwest northwest joint set, the southwest lineation being the more prominent, and structural foliation dipping gently to the west. The resultant style of mineralisation is confined to basinal features defined by topographical lows and is fairly lateral in extent (in order of 50m). Extraction of the mineralisation from this deposit is less arduous with recoveries more uniform, RE factors are frequently in the range 2 - 3. This style of mineralisation is more in line with what is to be expected from marine alluvial deposits, the nugget effect of diamond concentration being responsible for the high RE factor. The long narrow linear trends observed in Smith?s Ulcer demonstrably require a specialised approach in successfully sampling, modeling and ultimately mining.

Jan 1, 1998

By Paulo Chaves, Márcia Gonçalves, João R. S. Carvalho, Fernando J. A. S. Barriga, Edgar Carrolo, Tiago Luna, Ricardo Rato, Anabela Bento

INTRODUCTION For the last decades, deep-sea marine resources such as seabed massive sulfides (SMS), polymetallic nodules and ferromanganese crusts (Fe-Mn crusts) have received an ever- increasing amount of attention worldwide for their abundance in critical metals and potential commercial value. This interest has mostly been driven by the growing world demand for raw materials, in particular for high- and green-technology applications (e.g., hybrid and electric cars, batteries, photovoltaic solar cells, cell phones, super magnets), as well as by industrialized countries governments other than BRICS states need to secure a more diversified supply of metals, resulting in a new deep ocean exploration boom. Since the oceans and its resources are increasingly seen as indispensable for humans needs and their challenges in the decades to come, this boom increments pressure on marine areas, either in international or within countries economic exclusive zone (EEZ). Since 2002, the International Seabed Authority (ISA) has signed up 29 contracts with several entities and national governments from multiple countries (e.g., Japan, China, Germany, France, Russia, India, Rep. of Korea, UK, Canada, Brazil) for exploration for deep-sea mineral resources in international waters, either for scientific or commercial proposes, which together cover over 1.3 million km2 [1]. In turn, over 300 exploration licenses, covering more than 650,000 km2, have been granted within the EEZ of Pacific countries such as Papua New Guinea, Tonga, Fiji, Solomon Islands and Vanuatu [2, 3]. This number is expected to increase very rapidly, as 77 countries have proposed to the United Nations the extension of their continental shelf in order to extend their EEZ and jurisdiction over potential deep-sea mineral resources [4]. Its estimated that 42% of the potential areas for SMS occurrences, 54% for cobalt-rich Fe-Mn crusts, and 19% for polymetallic nodules lie within the EEZ of coastal countries [5]. In addition, a huge amount of seafloor is yet to be explored and evaluated. Combined, the size of the granted exploration areas represents less than 10% of the overall area thought as most favorable for the occurrence of the 3 types of deep-sea mineral resources above mentioned. This means that today’s assessments on deep-sea mineral resources are only a rough approximation.

Jan 1, 2018

By Arturo Carranza Edwards

One hundred ninety nine beach face sand samples from an equal number of beaches from the Mexican Pacific were studied. Based on petrological and chemical analysis some locations have been studied in more detail. Black sands from the following areas are discussed: (1) west Baja California Peninsula, where black sands rich in magnetite and ilmenite have maximum values of 50% iron and 14% titanium in the very fine sand fraction; (2) east Gulf of California, in its northern portion, the black sands show maximum values of 43% iron and 5% titanium in the fraction 2 to 4 0;-(3) the south Mexican Pacific, characterized mainly by medium sands, moderately well sorted, show that the fine sand fractions reach values of 35% iron and 41% titanium. X-ray fluorescence applied on selected samples constituted by feldsarenites and lithic feldsarenties, showed the presence of rare elements in some of the studied samples.

Jan 1, 1994

By Seung-Kyu Son

Environmental properties of the northeast Equatorial Pacific along 131.5 degrees west, between 5 degrees and 13 degrees north latitude, were investigated in association with changes in water column structures during the summer seasons of 1998 and 1999. Climatic disturbances such as El Nino and La Nina, should have affected this area during the study period. In 1998, a thermocline where temperatures rapidly decrease with depth, was formed at 90~110 m water depth. However, in 1999, a very fluctuating thermocline was observed with latitudes. As a result of changes in the water column structures, biological and chemical environment also showed fluctuation parallel to the changes in other physical parameters. Inorganic nutrient depleting areas, especially for nitrate+nitrite and phosphate, or oligotrophic regions were extended down to approximately 100 m depth, which coincided with the surface mixed layer depth. In the euphotic zone, depth integrated nitrogen (N) and phosphorus (P) values were 34 g-N/m2 (grams of Nitrogen per square meter of sea floor), 7 g-P/m2 in 1998 and 130 g-N/m2, 18 g-P/m2 in 1999, respectively. The results indicated that nitrogen (96 g-N/m2) and phosphorus (11 g-P/m2) are supported by up-welling and down-welling phenomena with convergence and divergence in the study area. Biological parameters in the water columns were largely determined by the physico-chemical environmental parameters. Subsurface chlorophyll maximum layers were coincided with the formation of seasonal thermocline. Copepods were the dominant group of zooplankton community at three sampling stations (N5, N6, N10) terms of abundance, which was the same results of previous surveys for the past 3 years. Among copepod populations, Oncaea sp., Oithona sp. Clausocalanus sp., Acarocalanus sp. and juvenile copepodites were dominant Appendicularians, foraminiferans and radiolarians were also dominant. To investigate diel vertical migration pattern of zooplankton, repeated samplings from the water depth of 0~50m and 50~200m were conducted at KODOS (Korea Deep Ocean Study) area before and after sunrise. Zooplankton abundance was slightly higher after sunrise than before sunrise in the surface layer. Chlorophyll-a concentrations were relatively low as the concentration of sediment increased in most experiments possibly due to a decrease of grazing pressure of microzooplantkon such as ciliates, which is the efficient grazer on small-sized phytoplankton. Because copepod predation on microzooplankton may be prevented by the high concentration of sediment, resulting in lower grazing pressure on small-sized phytoplankton. The results obtained during the baseline study as a part of KODOS project since 1998.

Jan 1, 2001

By Isobel Yeo, Florent Szitkar, Sven Petersen, Sebastian Graber, Nico Augustin, Marcel Rothenbeck, John Jamieson

"INTRODUCTIONSeafloor massive sulfides (SMS) along mid-ocean ridges are often seen as a possible future contribution to a secure metal supply for global human needs. A growing interest over the past few years resulted in six national exploration licenses and one application pending, covering 10,000 km2 each, that have been brought before the UN International Seabed Authority (ISA) since 2011. Each contractor has to explore these 10,000 km2 within the 15-year runtime of the contract. However, the need to define areas that are not economically interesting is more pressing, as 50% of the 100 license blocks have to be returned to ISA after only eight years - hopefully areas that do not contain large and economically interesting SMS deposits. Current geochemical prospecting technologies, however, have mainly been developed for the search for active hydrothermal systems (e.g. hydrothermal vents and associated black smokers) that can easily be traced through physical and chemical anomalies in the water column (temperature, chemical variations of elements such as Mn, Fe, redox potential, and/or the particle concentration in the water column). Such plume surveys have been a primary tool for exploration of SMS systems, but they only identify active, and therefore mostly young and small hydrothermal systems. In a recent high-resolution AUV survey performed within the EU-FP7 funded project “Blue Mining”, we covered 47 km2 along the TAG segment of the Mid-Atlantic Ridge to test exploration methodology for fast and reliable exploration of larger areas of the seafloor for inactive seafloor massive sulfide occurrences using the autonomous underwater vehicle (AUV) “Abyss”."

Jan 1, 2017

By Mark D. Hannington

Seafloor polymetallic sulfides have been found in diverse volcanic and tectonic settings on the ocean floor at water depths ranging from 3700 meters to <1500 meters. More than 100 occurrences of hydrothermal mineralization have been documented (including Fe-oxide deposits, Mn-crusts, metalliferous sediments, and massive sulfides), but high-temperature hydrothermal activity and large accumulations of polymetallic sulfides are known at fewer than 20 different sites. Chemical analyses of samples from these deposits indicate that they contain important concentrations of Cu, Zn, Ag, and Au, comparable to those of massive sulfide deposits on land. However, the lack of sufficient data concerning the distribution, size, and bulk composition of seafloor deposits precludes a meaningful assessment of their resource potential.

Jan 1, 1994

By Jai-Woon Moon

Lemkein seamount located in the west of the Kuwajleen Atoll of RMI is a relatively samll, simple-shaped, peaked type seamount with its base at 4,500 m and summit at 1,452 m water depths. Ferromanganese crusts were identified in the water depth range between 2,000 m and 2,500 m, and they were mostly observed on the northern slopes of the seamount. Among various substrate rocks, breccia occurred most commonly with crusts and formed the thickest crust layers. Average thickness of the Lemkein crusts was about 5 cm. Their chemical compositions were similar to other crusts found in the RMI area; Mn=25.82%, Fe=15.29%, Co=0.74%, Ni=0.56%. Lemkein crusts were characterized by their four distinctive internal layers; 1) Massive Layer 1; 2)Porous, Fe-stained or sediment infilled Layer 2; 3) Massive to slightly porous Layer 3; and, 4)Massive, Dense, Phosphotized, CFA veined Layer 4. Layers 1 and 2 were generally similar in composition, but highest Co concentrations were measured in Layer 1 while relatively higher concentrations of Al, Rb, Fe, and Ti were observed in Layer 2. Layer 3 showed higher concentrations of Ca and P than Layers 1 and 2. Based on the Co-chronography, the age of Layer 1 is 0¡?6 Ma (growth rate = 1.50 mm/Ma), Layer 2 is 6¡?15 Ma (1.75 mm/Ma), Layer 3 is 15¡?27Ma (1.76 mm/Ma), and Layer 4 is 27¡?45 Ma (2.06 mm/Ma). These preliminary results indicated that high Co contents in Layer 1 resulted from slow growth rates; Layer 2 was formed under relatively strong influence of high terrestrial input; and, Layer 3 was probably affected by a minor phosphatization event occurring in 15 Ma.

Jan 1, 2000

By G. B. Carpenter

The United Nations Law of the Sea (LOS) Convention includes provisions (Article 76) for establishing the outer limits of a coastal State&apos;s continental shelf and for denoting the seaward extent of sovereign rights over natural resources. Determination of a coastal State&apos;s continental margin, according to Article 76, must consider eight factors: 1. The territorial sea baseline 2. The 2,500-meter isobath 3. The foot of the continental slope 4. A line 200 nautical miles seaward of the territorial sea baseline 5. A line seaward of the foot of the continental slope connecting the points where sediment thickness divided by distance to the foot of the slope equals .01 6. A line 60 nautical miles seaward of the foot of the continental slope 7. A line 100 nautical miles seaward of the 2,500-meter isobath 8. A line 350 nautical miles seaward of the territorial sea baseline Figure 1 shows the preliminary limits for each of the Article 76-based definitions for a portion of the U.S. Atlantic continental shelf. The additional areas gained beyond the 200- nautical mile Exclusive Economic Zone (EEZ) are highlighted. The first three factors are baselines from which the distance provisions of Article 76 are measured. Factors 4-8 are distance- from-baseline provisions for establishing the continental shelf limits. Factor 5, also known as the Depth of Sediment Limit or "Irish Formula", was calculated using sediment thickness data from seismic linesand isopach maps. All other factors were determined from digital hydrographic data. The Depth of Sediment Limit is the most advantageous method for the area shown in Figure 1. It is especially useful for introverted coastlines such as the Georgia Embayment and New York Bight areas. The 200-mile line is advantageous for protruding coasts such as those off major capes, e.g., Cape Hatteras. The 2,500-meter isobath plus 100-mile line gains

Jan 1, 1995

By Ian Selby

Resource management is a key factor in the operation of a successful marine aggregates business; it is integral to the development of sustainability, satisfying increasing commercial, quality, and environmental performance standards. Resource management is based on the combination of; (i) a thorough evaluation and understanding of the resources on the sea bed and (ii) a dredging plan targeted to permit the effective and efficient extraction of the resources whilst mitigating impacts and leaving the sea bed ready for recolonisation.

Jan 1, 2004

By A. M. Olivarez

The elucidation of the theory of plate tectonics has provided a conceptual framework for understanding the formation and distribution of different types of ore deposits. For example, we now recognize that certain kinds of mineral deposits are generally associated with a particular type of plate boundary (i.e., massive sulfides often occur along divergent plate boundaries, whereas porphyry copper deposits are typically found along convergent boundaries). During certain geologic time periods, plate reorganization events have changed the relative proportion of different types of plate boundaries. Corresponding changes have been observed in the abundance and distribution of ores deposited during these times. The present study examines the temporal aspects of this relationship; i.e., do plate reorganization events play an active or passive role in ore formation? In other words, do plate reorganizations simply provide a more favorable tectonic setting in which ore formation can occur over significant time periods, or are they directly linked to the mineralization process? We have examined this question by comparing regional tectonic histories with the ages of known massive sulfide and porphyry copper deposits. Because these deposits, in particular massive sulfides, form as a result of hydrothermal activity, we have also compared regional tectonic histories with proxy indicators of this process in the marine sedimentary record. These indicators include increased mass accumulation rates of Ca, Fe, Mn, and opal, characteristic changes in the Sr/Ca and Mg/Ca ratios of biogenous carbonates, and shoaling of the carbonate compenstion

Jan 1, 1988

By Nii Allotey Odunton

One of the primary responsibilities of the International Seabed Authority?s Secretariat (the Secretariat) is to assess the quantities of metals present in seabed polymetallic nodules in the International Seabed Area under the Authority?s jurisdiction. To carry out this responsibility, the Secretariat periodically undertakes an assessment of the reserved areas in the Clarion-Clipperton region of the northeastern Pacific (CCZ) using the data submitted by the registered Contractors and maintained in the Authority?s POLYDAT database. The results of its most recent assessment demonstrated that the information submitted by the Contractors, though satisfactory for some purposes, does not permit the in situ quantities of metals in these areas to be estimated with a degree of confidence that is comparable to many land-based mineral resource estimates. Our strategy is to divide the work into two distinct but closely related efforts; one to draft a Prospector?s Guide that provides a narrative description of the key geological and oceanographic data that may be related to deposit abundance and metal content, and another that we call the Geological Model, that summarizes and documents the quantitative resource assessments accomplished in the project.

Jan 1, 2005

By Freddy Pøhner

The paper describes recent advances in the technology for mapping of the seabed with acoustic instrumentation. These instruments are typically single beam echo sounders, multibeam echo sounders and high resolution sub bottom profiler. For the single beam echo sounders, new features for deep water mapping are described, as well as the possibility for combining investigation of shallow areas with side scan sonar and vertical echo sounding in the same instrument. Multibeam echo sounding technology for deep and shallow water is reviewed, and some new high resolution instruments using dynamic beam focusing is presented. The sediment profiling technology deals with a novel design for high resolution sub bottom profiling, based upon a Mills Cross transducer with resolution as good as 3 degree in its largest configuration and a frequency range of 2,5 ? 7 kHz. Remarkable features of the system are a very high ping rate even for deep water, and the capability to map buried objects or structures by several simultaneous beams. Some results obtained with the first installation on the French research vessel ?Beatemps Beaupré? are presented.

Jan 1, 2003

By Alexander Malahoff

The new ship-submersible system with R/V Ka&apos;imikai-o-Kanaloa as a mothership and the PISCES V as the submersible completed its first season of dives. The dives involved deployment of the PISCES V in the Hawaiian Islands between the months of July and October 1996. Submersible deployments up to depths of 2,000 meters in sea states up to a high three were made. The new hook and clasp deployment and retrieval connection for PISCES V to the telearm was shown to be an effective system for handling the PISCES V with the A-frame. The shipboard multibeam survey and seawater sampling capability proved to be especially effective in re-mapping the summit of the submarine volcano Loihi following a major volcano-tectonic event and for following the source and configuration of the new hydrothermal plume. Following the earthquake swarm of July 17 to August 18,1996, major changes in the geological setting of Loihi submarine volcano took place. Prior to the seismic event, the geology and structure of the summit of Loihi was represented by a platform-like area 8,100 meters long and 5,400 meters wide enclosed by the 1,200-meter depth contour. The summit was characterized by the presence of two prominent pit craters and eastern and western crater located at water depths of 1,100 and 1,370 meters, respectively. A hydrothermally active volcanic cone, named Pele&apos;s Vents, was located at a depth of 960 at the southern edge of the summit. The floor of the summit of Loihi was largely covered by prismatic talus, with interstitial hydrothermal clays. Pillow and tube lavas with volcanic cones 5 to 50 meters high were exposed along the axes of the southern and northern rift zones. The inner margin of the summit displayed fissures and normal faults with the downthrown component towards the center of the summit. The pre-earthquake structural data suggest a pre-caldera structural stage for Loihi. Maximum sustained hydrothermal activity observed on Loihi over the past 10 years existed at Pele&apos;s Vents with other sporadic venting occurs along the summit platform and along the south rift. Following the earthquake swarm, the hydrothermally saturated Pele&apos;s Vents cone gave way and slid into the inner pit crater. Subsequently, the observed above- bottom hydrothermal plume source deepened from 960 to 1,160 meters, possibly emanating from the same intrusive heat source as Pele&apos;s Vents. The observed inward collapse of the summit structures and subsequent opening of fissures gave rise to diffuse venting from the newly formed caldera-like depression with the bottom-hugging hydrothermal pool located at depth between 1,250 and 1,220 meters at the sites of the pit craters.

Jan 1, 1996

By Gary J. Massoth

Wherever hydrothermal fluids vent from the seafloor they will buoyantly rise (up to 100?s of meters) while mixing with seawater before attaining density equilibrium and dispersing laterally as neutrally buoyant plumes commonly 50 to several 100?s of meters in thickness and with order-of-magnitude or greater breadth. Although these plumes are typically >10,000-fold dilutions of vent fluids they can be reliably detected using sophisticated physical sensing and chemical techniques. Hence, hydrothermal plumes are spatially large targets compared to the actual sites of seafloor fluid discharge and resulting mineralization. For this reason plume prospecting techniques evolved over the past 20+ years have been widely used to systematically explore over 10% of the 60,000-km-long system of mid-ocean ridge (MOR) spreading centers for hydrothermal activity. While plume detection and gradient mapping can be used to home in on venting sites, plume chemical signatures provide additional insight regarding the nature of the fluids being discharged on the seafloor. We have applied the systematic plume prospecting techniques developed on MORs to the volcanic frontal arc setting as part of the NZAPLUME (New Zealand American PLUme Mapping Expedition) surveys. NZAPLUME I in March 1999 marked the first systematic reconnaissance of any intra-oceanic arc for submarine hydrothermal activity. Seven of thirteen previously mapped volcanoes that comprise a 260-km-long section of the southern Kermadec arc northeast of New Zealand were confirmed to be hydrothermally active. On average, one hydrothermally active volcano was found along each 35 km of arc front, a rate comparable to slow- and intermediate-rate spreading MORs. During NZAPLUME II in May 2002, thirteen previously unknown volcanoes and 8 satellite cones were first swath mapped for bathymetric detail and then surveyed using plume prospecting techniques. Three active venting sites were discovered along this 580 km-long arc section, bringing the total to 10, or 39% of 26 volcanoes surveyed overall, still an appreciable frequency rate for venting sites compared to MORs. While only chemical results for NZAPLUME I are available, the arc plumes characterized so far are chemically diverse and rich compared to MOR plumes. This diversity and enrichment was most evident as ultra-high concentrations of CO2, sulfur gases (St = SO2 + H2S), and Fe within plumes over several volcanoes. We suggest the fluids discharging from the seafloor at these sites are volcanic fluids, i.e., hybrid fluids comprised of MOR-like hydrothermal fluids evolved from seawater-rock reaction and fluids exsolved from magma as acid volatiles and liquid brines.

Jan 1, 2002

By D. S. Cronan

Based on analogy with the Clarion-Clipperton zone, three main factors appear to influence the occurrence of potentially economic nodules in the study area, (i) elevated biological productivity, mainly above 50gCm-2y-l, (ii.) sea floor depth near or below the CCD, (iii) an absence of turbidite sedimentation. These conditions are fulfilled in parts of the following basins, where available data indicate that high grade and sometimes abundant nodules occur. i) The East Central Pacific Basin west of the Line Islands extending to the East Central Pacific Basin north and east of the Phoenix Islands ii) The West Central Pacific Basin west and northwest of the Phoenix Islands iii) The North Penrhyn Basin north of Penrhyn Island Notwithstanding the similarities between the environmental conditions under which potentially economic nodules occur in the Clarion-Clipperton zone and in the areas listed above, such similarities may relate only to present day conditions. During the possibly long periods of nodule formation, environmental conditions may have varied, and the deposits formed under conditions different from those prevailing at the present day. However, the fact that both present day conditions and the deposits in the two areas do show similarities suggests that applying the same genetic model to them has some validity. Possibly, any changes in environmental conditions during the period of formation of the deposits has been similar in both areas. Such uncertainties can only be resolved by a much fuller evaluation of the evolution of nodule deposits in both areas throughout recent geological time.

Jan 1, 1986

By Olav Rune Godø

We present a science-based infrastructure for continuous online monitoring of the ocean interior including benthic, pelagic and the demersal habitats. It will reduce expensive ship based monitoring costs associated to offshore and coastal industries. We combine established Norwegian cabled observatory technology and German mobile seafloor robotic technology and thus supports the transition from local to spatial ecological monitoring. Both technologies are developed through science - industry partnerships. In Norway, the Institute of Marine Research has worked with Statoil ASA and Metas AS to install and operate the LoVe cabled observatory. The German technology is developed by iSeaMC and Kraken Robotik, two spinoff enterprises of the Helmholtz Alliance “ROBEX”. GEOMAR has recently developed a lander-based deep-sea crawler that operates autonomously based on the original iSeaMC crawler system using the Kraken Autonomy. Combined with the Spanish image processing and modelling expertise in the SME Deusto Sistemas SA the consortium hosts the capacity to establishing a complete semi-autonomous real-time monitoring system. Merging of existing technologies into one operational autonomous product through the unique competence of partners’ support international ambitions (e.g. Blue Growth, GES, Horizon 2020), and renew monitoring that assess impact of human use of the marine environment. The consortium has been invited to contribute to technology/science programs for the Yellow Sea and for European mining and offshore decommissioning industries, which demonstrates the leading role of our consortium. The project is funded through the EU Martera program and started in June this year.

Jan 1, 2018