Search Documents

By Y. M. Ha, T. D. Nguyen, D. T. Nguyen, H. K. Choi

Conventionally, cement deep mixing (CDM) columns are designed to have constant diameters over the improved depth as this facilitates the construction procedures. However, this design pattern may be inefficient in cases of spread footings or shallow foundations. This paper first briefly introduces principles of an improved CDM method that can create head-enlarged CDM (termed PF) columns. A simple analysis approach was introduced to obtain optimal shape of PF columns that results in minimum settlement. The effectiveness of this improved method over the conventional CDM method was then illustrated by settlement analysis for an actual footing in a case study using two recommended analytical methods in the literature. Analysis results from the case indicated that by using the same amount of soil-cement mixed volumes, settlement from a footing on PF columns can reduce up to 10 % compared with that from the same footing on CDM columns. In addition, a material quantity comparison for the case indicated that to have the same settlement values the volume of each PF column can be reduced of around 10% compared with that of the CDM column. INTRODUCTION The cement deep mixing (CDM) method is one of the most popular methods in ground improvement works. Details on the method such as construction procedures, necessary equipment and recommendations are described in many references or manuals (e.g. Bruce et al. 2013, BS EN 2015, Kitazume and Terashi 2013). Conventionally, CDM columns are designed to have constant diameters over the improved depth as this facilitates the construction procedures. However, this design pattern is found inefficient in cases of spread footings or shallow foundations as the upper soil layers are naturally weaker than the deeper ones but are subjected to larger amount of induced stress from the superstructures.

Jan 1, 2019

By Brenton Cook, Daniel Mageau, Larry Applegate, Aaron McCain

"Ground freezing was successfully used to create an impermeable barrier wall along 3,000 feet of the downtown Seattle waterfront as part of the Seattle Seawall Replacement Project. This $360 million re-development involved removing the original 1930-era seawall and replacing it with a new, seismically resistant concrete wall supported on fill soil improved by jet-grout. The replacement wall was one of the largest construction projects in the state of Washington at the time. Ground freezing is typically used as both a structural shoring wall and groundwater cutoff. However, at this project it was used primarily as a cutoff wall to stop groundwater seepage into the 16-foot deep excavation from the landside areas.The project was divided into ten boxes (sections), each typically 200 to 600 feet in length. Only a few boxes were under construction at one time to reduce the impact on tourist-dependent local businesses. Soil conditions in the freeze zone consisted of sand, gravel and silt fill with abundant wood and debris. Tidally influenced groundwater, much of it contaminated, was difficult and expensive to control using wells during initial stages of construction. For all subsequent stages, a frozen soil wall extending to about 35 feet in depth was used to stop groundwater seepage into the excavation. An additional benefit of ground freezing included elimination of potential settlement beneath nearby buildings, utilities, and the Alaskan Way Viaduct that would likely have occurred with the use of conventional dewatering wells. The frozen soil wall crossed more than 130 buried utility locations (including water, sewer, storm, electrical, fiber optic, phone, gas, steam) with no damage. The frozen soil wall was very successful and limited groundwater influx from the landside to the seawall excavation to a negligible amount so that pumping, storage and treatment of contaminated groundwater was essentially eliminated."

Jan 1, 2016

By A. Felipe Uribe-Henao, Camilo Ballesteros, Luis G. Arboleda-Monsalve, David G. Zapata-Medina

Conventional excavation analysis based on total or effective stress methods can result in inaccurate estimation of ground movements when impervious soil conditions or rapid excavation sequences are not found in the excavation (i.e., assumption of undrained response is not valid). The influence of excavation rate, hydraulic conductivity, and excavation geometry on the fully coupled solid-fluid behavior of a braced excavation in cohesive soils are studied parametrically using PLAXIS2D. The coupled excavation analysis is performed using the Hypoplasticity clay model to reproduce the constitutive behavior of soil and the poro-elasticity Biot’s theory to account for changes in pore water pressure due to deformations in the soil skeleton. Results obtained from the parametric studies indicate that excavation rates to hydraulic conductivity ratios, ER/k, smaller than 0.1 and larger than 104 can be used as limits for drained and undrained analyses, respectively. In practical applications, undrained and partially drained excavation analysis with ER/k larger than 102 resulted in a similar ground deformation. However, smaller ER/k ratios demand fully coupled solid-fluid analysis. An analytical method aimed at predicting excess pore water pressures and determining the required type of analysis associated with soil and excavation conditions, e.g., drained, partially drained, and undrained analysis, is proposed herein to accurately estimate the ground movements induced by the excavation.

By David S. Graham, Benjamin Turner, Paul J. Axtell

Seismic challenges were at the forefront of design for two parallel replacement bridge structures over the Arkansas River as part of the I-30 Crossing Project in Little Rock, Arkansas. Although not an area of the country typically associated with high seismicity, proximity to the New Madrid Fault Zone resulted in design ground motions sufficient to trigger liquefaction in alluvial channel and point bar deposits. A detailed post-award subsurface investigation program utilized CPT with complimentary borings to obtain samples for laboratory testing to assess the continuity of potentially liquefiable layers, from which we concluded that continuous zones of liquefaction across the extent of the north approach could lead to lateral spreading towards the river. An overview of the foundation and superstructure design to resist lateral spreading forces in accordance with the latest published design guidelines and research is presented. Other seismic aspects of the design are covered including timber pile ground improvement to mitigate liquefaction at the north approach embankment and foundation input motions that differ from code-based ground surface motions due to foundation stiffness, strength, and geometry. The project showcases an example of successful collaboration between geotechnical and structural designers with contractor input to address seismic challenges in the South Central US. Furthermore, the importance of considering kinematic demands on columns and other superstructure components – not just foundations – is highlighted.

Sep 8, 2021

By KeerthiRaaj Subrmanian, Muthukkumaran Kasinathan

"A railway embankment is under construction between Nagapattinam to Thiruthuraipoondi covering 36.5 km. The sub-soil strata comprises of soft clay extending up to 10 m below existing ground level, which is subjected to stability and settlement problems. A trial stretch covering about 5 kilometer was improved using Prefabricated Vertical Drains (PVD) with surcharge was recommended to accelerate the consolidation settlement. The geotechnical characteristics of the subsoil are examined through laboratory tests on representative soil samples. Recent improvement in the finite element analysis has facilitated modeling of PVD in finite element software for computing the settlement magnitude and time rate of consolidation. In this study the theoretically predicted settlement magnitude and time rate of consolidation from Terzaghi.s vertical consolidation, Barron's radial consolidation are compared with the analyzed FEM results for both the cases with and without PVD improved embankment. The comparative analysis between FEM and predicted data hold good for stresses and the associated deformations. The excess pore water pressure was significantly lower and their dissipation was faster in case of embankment with vertical drains. Thus PLAXIS 2D tool shows fairly convincing results in comparison to the theoretical solutions.1. INTRODUCTIONFrom the earlier times civilization has been developed in a fashion either at the banks of river or near to the shore region, because of the easier availability of food and water. This over centuries made them as huge cities, consequently population rise made the increased necessity of highway, railways, port and even more ground for construction. As a stake researchers are pushed to make a low bearing ground into a massive carrier of skyscrapers, embankment, bridges etc. These low bearing ground suffers from total and differential settlement, slope instability. Hence, numerous ground improvement techniques were followed to eradicate these concerns which include preloading, piling, stone column, vertical drains and geosynthetic reinforcement. Among them Prefabricated vertical drain (PVD) are often used to accelerate consolidation of soft subsoil and has been the main soil improvement method used in improving the soft marine clay deposit (Chu et al.(2004); Chai (2001) and Arulrajah et al.(2003)). Literature review of embankment over soft clay deposit reveals that combination of PVD with preloading is widely considered as an economical and less time consuming ground improvement technique."

Jan 1, 2015

By Martin B. Hudson, Kenneth S. Hudson, Gwendolyn Arreguin

A twin high-rise project site in Century City posed several foundation engineering challenges for the design team. One portion of the twin high-rise project site was required to utilize top-down construction in order to allow a driveway to remain open during construction of the project’s 40-foot deep excavation. The challenge was compounded by the need to utilize a mat foundation to support the high-rise construction and yet have temporary drilled shafts through the mat foundation area that would not create excessive differential settlement. This was accomplished by constructing a deck supported by eight drilled end- bearing drilled shafts with Osterberg load cells and five 7-foot-diameter end-bearing drilled shafts. The Osterberg load cells served to verify the capacity of each of the drilled shafts and preload the soils at the drilled shaft tips. The 7-foot-diameter shafts were constructed with bond breakers to prevent skin friction but instead mobilize end bearing (for settlement compatibility with the surrounding mat foundation). After the drilled shafts were placed, then top-down construction began beneath the driveway, leaving the driveway supported on the drilled shafts. Construction challenges included drilling of the shafts through previously abandoned tieback anchors from an adjacent parking structure basement, as well as cemented layers within the rock materials. The paper describes the use of the various analytical methods used to calculate capacities and check settlement compatibility, the construction and testing methods utilized, and the construction challenges encountered. INTRODUCTION Wood Environment and Infrastructure Solutions, Inc. (hereafter referred to as Wood) performed a geotechnical investigation for the New Century Plaza currently being constructed in the Century City District of Los Angeles, California. The New Century Plaza project consists of the construction of two new towers (designated as North and South Buildings) and the rehabilitation of the existing Hyatt Regency Century Plaza Hotel. The existing hotel tower is 15 stories in height above the existing grade and is underlain by four subterranean basement parking levels. The new North and South Buildings will stand approximately 46 stories in height above the existing grade to accommodate residential use. The new towers are planned west of the existing hotel. The site was previously occupied by the existing hotel subterranean parking structure and overlying podium structure, and a loading dock in the southwest portion of the site. The former western portion of the podium and subterranean parking structure west of the existing hotel building western edge were demolished to allow for new subterranean levels, a new podium structure, and the new towers. The lowest floor of the proposed subterranean level required excavation on the order of 35 to 80 feet.

Jan 1, 2019

By Mark R. Svinkin

"Construction equipment and operations usually produce soil and structural vibrations which may harmfully affect various structures and also the content of buildings and houses. The level of structural vibrations depends on a number of factors such as characterized sources of vibrations, soil conditions, and susceptibility of structures. There are certain knowledge and experience for managing the effects of construction vibrations which require implementation of condition survey of structures, information on construction dynamic sources and soil conditions at a site, evaluation of possible vibration effects on structure, calculation of ground vibrations before construction, use mitigation measures to decrease vibrations, and a choice of appropriate vibration limits. The paper presents the application of known concepts for assessment of vibration effects on structures from bridge constructions.INTRODUCTIONVibrations producing by construction activities such as pile driving, dynamic compaction of loose soils, demolition work, heavy construction equipment and trucks can affect adjacent and remote structures. Vibration effects on structures, sensitive devices and processes may create significant practical problems. Legal actions are often required for solutions of vibration consequences. The level of construction vibrations depends on dynamic sources, soil conditions at a site in particularly availability of soils with settlement potential, distances from the sources, parameters of waves propagating at a site and susceptibility rating of adjacent and remote structures. It is likely that intolerable structural vibrations from direct vibration effects of impact pile driving and resonant floor vibrations from vibratory pile driving may be induced in adjacent structures to construction sites.Foundation settlements resulting from soil vibrations in loose soils usually occur in the proximity of dynamic sources, but it is important that dynamic settlement may happen at various distances from the source. There are such examples. First, Kaminetzky (1991) mentioned a case history of building settlements developed at a distance of about 305 m (1000 ft) away from a pile driving site. Foundations of the buildings were underpinned on piles down to the tip elevation of the new driven piles to prevent building settlements. Second, Lacy and Gould (1985) shows that the peak particle velocity (PPV) of 2.5 mm/s (0.1 in/s) of ground vibrations could trigger dynamic settlements at distances up to 30.5 m (100 ft) from driven piles."

Jan 1, 2016

By Packer M. L

Residual load development in driven precast piles has been widely researched in recent decades, however, cast-in-situ piles are often falsely assumed to be unaffected by this mechanism. In contrast to driven precast piles, driven cast-in-situ (DCIS) piles require adequate time prior to loading for the concrete hydration and curing processes to occur. The concrete-soil interaction is complex with several processes influencing the strains within the concrete pile after installation. DCIS piles are of particular interest given that residual loads can be developed during both the driving and casting phases. This paper present four instrumented end-bearing DCIS piles in which temperature and strains were monitored from installation, with the objective of identifying the processes contributing to the measured strains prior to testing. Strain gauges at all depths recorded a net compression and compressive strains continued to increase up to the commencement of load testing. Residual strains in the test piles were interpreted to be influenced by temperature (concrete and ambient soil and air temperature), consolidation of soils due to dissipation of excess pore water pressure, and swelling from absorption of groundwater. Several residual load interpretive methods are evaluated with the Siegel and McGillivray (2009) approach being consistent with the skin friction full mobilisation theory of the Unified Design method. The full-scale field tests presented herein provide a unique opportunity to examine DCIS pile behaviour, particularly given the lack of presently available published studies on these pile types.

May 1, 2022

By Onur Guvener, Kalaiarasi Vembu, C. Vipulanandan

"Installation procedure and the quality of the material used in the construction have significant effects on the behavior of the Auger Cast in Place (ACIP) piles. In this study, Installation and curing of a 760 mm (30 in.) diameter and 12 m (39 ft) long ACIP pile with a design capacity of 1140 kN (128 tons) in hard clay was investigated. Construction quality was monitored using the automated monitoring system where the volume of grout pumped and the pressures were monitored with depth. The curing of the pile was monitored using axial vibrating wire strain gages at four levels and lateral vibrating wire strain gages at two levels. The residual strain and temperature profile in the curing pile was monitored over a period of week to determine the appropriate time for load testing the pile. Axial behavior of Auger Cast in Place (ACIP) Piles in hard clay was studied using full scale load test on an instrumented pile. The load-settlement and load transfer relationships of the pile was investigated based on the load test results. Development of skin friction in the load test pile and the reaction pile was also investigated.INTRODUCTIONAugered cast-in-place piles (ACIP) are drilled foundation installed by drilling a hole with a continuous flight auger to a predetermined depth. Non-displacement Augered Cast-in-Place (ACIP) piles are increasingly used for supporting building, bridges, sound barrier walls and many other structures around the world. In an ACIP pile, depending on the soil type and rate of the auger advance, ground stresses are maintained near the value that existed before construction by using a continuous flight auger, which is never withdrawn until the cementitious material (fluid Portland cement grout) is placed by pumping the grout beneath the withdrawing auger under pressure through the hollow stem of the auger (Vipulanandan, 2005). ACIP piles are typically installed with diameters ranging from 0.3 to 1.0 m and lengths up to 30 m (Brown, 2005) although longer lengths have occasionally been installed. Comparing to the drilled shafts and driven piles of equivalent size ACIP piles can be installed more rapidly with fewer disturbances to the surroundings in favorable geological conditions. Hence the installation procedure and the quality of material used in the construction have significant effects on the behavior of ACIP piles (Vipulanandan, et al. 2007). In this paper construction quality control technique for ACIP piles was investigated. Load displacement and load transfer behavior of pile in compression and tension in hard clay was also studied. The development of side resistance in compression and tension for the load test piles and the reaction pile were also investigated."

Jan 1, 2017

By Muhannad T. Suleiman

The design of deep foundations supporting heavy buildings, bridges, transmission lines, and highway structures, is governed by lateral loads in many cases. However, due to the use of empirical or semiempirical approaches to develop the soil force-displacement relationships (i.e., p-y curves), a wide range of recommendations are presented in the literature. Recent efforts by the author and co-workers enabled simultaneous direct measurements of soil-pile interaction pressure and lateral movement along the pile length, resulting in p-y curves based on direct measurement. Advanced sensors including sheet pressure sensors and shape acceleration arrays were used in these experiments. The experiments were conducted at the Soil-Structure Interaction (SSI) facility funded by the Major Research Instrumentation Program at the National Science Foundation. This paper focuses on the SSI of single laterally loaded piles. The test pile was 101.6 mm in diameter and 1.42 m long, which were installed in well-graded loose sand. This paper provides a summary of the installation and testing procedures, soil properties, pile instrumentation, measured lateral load-displacement response, strain profile along the pile length, lateral movement along the pile length and the pressures measured at the soil-pile interface. Furthermore, the paper presents measured p-y curves compared to estimated p-y curves using empirical methods available in the literature.

Jan 1, 2011

By Alan G. MacKinnon

The current piling practices in the U. S. have, to a great degree, been influenced by our founding fathers. When our constitution was written by the delegates from the original thirteen colonies, it was a document of compromise. Generally, the individual states retained their sovereign power over those duties that they had historically performed. The concept of States Rights has been tested throughout our history and has been preserved as of today. An example of the extent of this protection is occurring in the State of Ohio where I currently live. Each of the 50 states receives funds for highway construction from the federal government, approximately in proportion to its population. Congress, when it allocates the funds, quite often attaches amendments to the funding bill to exercise their authority. The major amendment prior to the most recent increase in the speed limit to 65 mph from 55 mph was to increase the legal drinking age to 21 from 18 years old. Embodied within the bill was the provision that the Federal government deduct a percentage from the allocation of any state that did not revise its legal drinking age law from 18 to 21. In the State of Ohio, this change in the law was put to a vote of the people and it was defeated. The federal government now is deducting funds

Jan 1, 1987

By Alexandra Weidle, Seffen Leppla, Rolf Katzenbach, Matthias Seip

"A lot of different deep mixing systems have been developed in the last decades for a wide spectrum of applications, e.g. retaining and foundations systems, soil improvement, sealing of toxic substances or dyke strengthening. The paper will deal with special aspects of constructions with deep mixing systems for infrastructures like soil improvement for cyclic loadings and underpinnings in difficult soil conditions by presenting cases from engineering practice.1. DEEP DRY SOIL MIXING FOR SOIL IMPROVEMENT OF RAILWAY TRACKS IN VERY SOFT SOILS1.1 IntroductionRailway tracks are set into vibrations by train passing. In very soft soil this leads to long-term deformations which lead to speed limits, temporary closings and big maintenance efforts. The energy of the dynamic loading is transmitted into the soil by compression and shear waves and at the surface by rayleigh waves (Wood 1968). The expansion of the waves are influenced by•,thickness of the soft soil layer•,density of the soft soil layer•,stiffness of the soft soil layer•,saturation of the soft soil layer•,frequency of the dynamic loadingThe frequency of the dynamic loading depends on the train velocity and the distance of the wheels and wheel sets. If the frequency of the dynamic loading is in the range of the natural frequency of the soft soil layer the vibrations increase extremely (Lieberenz et al. 2003). As a result the long-term deformations will increase as well.To avoid these long-term deformations and the resulting operation restrictions and maintenance efforts an adequate soil improvement is necessary. For the optimization of the soil improvement field tests have been carried out.1.2 Experimental field testsThe field tests have been carried out at a 300 m long test track with five different setups, each 30 m long:•,test track TS 0: no soil improvement•,test track TS 1: soil improvement with single lime-cement-columns 5.9 m deep (Figure 1a)•,test track TS 2: soil improvement with single lime-cement-columns 5.9 m and 10.4 m deep (Figure 1b)"

Jan 1, 2015

By Filippo Leoni, Wesley Schmutzler

"The LPV-111 East Back Levee Improvement Project lies along the Gulf Intracoastal Waterway (GIWW) in Orleans Parish of New Orleans, La., and is an essential component of the New Orleans Hurricane Protection System. The Hurricane Protection Office of the U.S. Army Corps of Engineers (USACE) attributed failure of the New Orleans East levees system to overtopping, erosion and subsequent breaching of LPV-111 along the GIWW, as well as other sections of flood protection during Hurricane Katrina in 2005. The existing levee suffered extensive damages from Hurricane Katrina, such that the USACE elected to provide earth stabilization and to rebuild the levee sections. Due to the adverse geotechnical properties of the foundation soils, the Corps deemed ground improvement necessary to stabilize the new levee and to limit its footprint. Wet Deep Mixing Method (DMM) was selected as the most suitable technology for this task.ChallengesDesign: This reach specifically protects East New Orleans and the Bayou Savage National Wildlife Refuge, the largest urban wildlife refuge in the U.S. and home to several threatened or endangered species of birds as well as many reptiles, amphibians and small mammals. The Corps chose DMM due to the sensitivity of the protected marshlands and because the method limits the footprint of the raised levees. The increase in the load bearing capacity of the treated soil significantly decreases the footprint necessary to attain the required height increase. This limitation required the new levee to have steep slopes, drastically increasing the surcharge on foundation soils characterized by overall poor geotechnical properties (soft clays and peats). The design also considered the increased horizontal stresses on the levees due to the extreme storm surges during a hurricane.The design of the 1.6 m diameter (5.25 ft) DMM elements called for overlapping them to form a double auger element that formed buttresses perpendicular to the levee alignment. The contractor installed the buttresses at a maximum on center spacing of 4.7 m (15.5 ft). One additional double auger DMM element was midway between consecutive buttresses at the centerline of the levee to further help prevent settlement (Figure 1)."

Jan 1, 2013

By Stephan Fisch, Franz-Werner Gerressen

"The use of cut-off-walls (COW) for the open pit coal mines has been used for decades. They have been used to reduce the negative hydraulic impact to the surrounding area caused by the open pit mining. The pile-guided trench cutting system is a worldwide unique technique, originally developed by the engineers of the mining companies themselves. It guarantees a continuous, joint free, COW during a continuous installation process. At this specific site in Welzow, this technique has been pushed to new limits in order to address the local lake region. Depth capability has been designed to about 430 ft (130m), proven are already depth of about 360 ft (110m) at a constant trench width of 39 inch (1000 mm). This project is approximately. 6.8 miles (11 km) long of COW, scheduled to be completed in 12 years period. About 2.05 miles (3.3km) have been installed, which is equivalent of about 3.5 Million ft² (330,000 m²). The system flushes special clay which forms a filter crust at the inner surface of the trench. Only natural clay resources used, in order to achieve the cut-off effect (colmation effect). The paper explains the installation process of the cut-off-wall as well as the equipment systems developed specifically for this project. After a successful start of the first phase of the project, the next step in the advancement of the equipment is already underway to enable the installation of greater depth to approximately 490 ft (150 m +) and beyond. The next generation equipment system is scheduled to start operation around 2018 INTRODUCTIONThis Serbian saying “Bóh je stworil Lužicu a cert je zaryl brunicu – God created Lusatia and the devil buried brown coal underneath it.” captures local communities’ ambivalence towards lignite.Lusatia is an almost entirely flat stretch of land between the Elbe and Neiße rivers dominated by glacial sands. On the surface, the heathland and woodland is hardly noteworthy. However, three large lignite mining regions, two in Brandenburg and one in Saxony, in the east part of Germany, divert the attention to underground level, down to depths of up to 120 meters. Here, seams crisscross the earth like ribbons. They were formed in the Tertiary around 17 million years ago.The mining of the lignite started almost 200 years ago. To enable open pit mining, a suitable dewatering system was required. At first, wells and drainage system were used. With the increasing demand to go deeper to enable full use of the existing resources with greater mining depth, a decision taken back in the 60th of the last century, the amount of water which had to be pumped increased dramatically. In peak times, approx. 1.57 Billion cubic yards per year (1.2 Billion m³/year) had to be pumped. This led to a lowering of the groundwater level for up to 230 ft (70 m), impacting the regional lake landscape. In order to reduce the influence on the water balance, and bring the water level back to pre1970th, a first development took place to implement the use of specific COW system to depth of about 147 ft (45m)."

Jan 1, 2017

By Ganesh Deepak K., Anjana R. K., Dr. Kumar Pitchumani N., Rajasekharam R. M. V. M. S. S.

The Phase 2 of Chennai Metro is being introduced in the city to ease the dependence on the existing transportation systems. Phase 2 is a combination of underground and elevated metro stretches comprising of three corridors. The current study focusses on the underground stretch of Corridor 3 which has a total of 29 underground stations. Construction of the underground cut and cover stations results in ground movements, which in turn impact the structures adjacent to the excavations. The greenfield ground settlement can be evaluated with the help of empirical approach or an approach requiring finite element modelling (FEM). The paper compares empirical and FEM approaches with regards to ground conditions in Chennai. Further, with the predicted ground settlements, building damage assessment is performed. The damage category of a building is defined based on the estimated tensile strains. This paper also compares the building damage assessment with empirical method and finite element modelling.

Nov 1, 2022

By Richard Hanke, Franz-Werner Gerressen

"The twin decked Alaskan Way Viaduct is a passage to Seattle’s downtown waterfront and of great economic importance to the city. In 2001, the Nisqually earthquake damaged the viaduct and led to the redevelopment of this corridor. The project includes two miles of 57.5 ft diameter bored tunnel beneath downtown Seattle and a stretch of new highway and overpass bridges at the southern tunnel entrance. State-of-the-Art special foundation equipment was mobilized for the project to perform a broad range of geotechnical construction. Applications included soil mixing and jet grouting for confinement cells around new bridge foundations, large diameter secant pile walls for the Tunnel Boring Machine launch portal along with an extensive jet grouting regime for ground improvements within the tunnel alignment. This paper will study the evolution and use of advanced special geotechnical construction equipment and describe its application at the Alaskan Way Viaduct Replacement Project.INTRODUCTIONThe evolution of geotechnical construction equipment continues through innovative applications and continued modification or enhancement of machinery. Similarly and in parallel, market expectations continually demand more in terms of construction speed and performance. Together, market demands and contractor innovation have led way to the development of specialty geotechnical construction equipment with capabilities previously not seen feasible or possible. Several examples of this scenario have recently developed during design and construction of the Alaskan Way Viaduct Replacement Project.The Alaskan Way Viaduct Replacement Project is a joint project between the Federal Highway Administration (FHWA), the Washington State Department of Transportation (WSDOT), and the City of Seattle. Three build alternatives were under consideration for replacing the Alaskan Way Viaduct: the Bored Tunnel Alternative, the Cut-and-Cover Tunnel Alternative, and the Elevated Structure Alternative. Ultimately, the bored tunnel option was selected as the best value approach. The project includes two miles of 57.5 ft diameter bored tunnel beneath downtown Seattle and a stretch of new highway and overpass bridges at the southern tunnel entrance. Several other associated improvements tie into this project that will ultimately lead to the complete demolition of the viaduct and redevelopment of Seattle’s waterfront."

Jan 1, 2015

By Morris J. D, Baldwin Z., Wiltcher P. M

21 Moorfields is an oversite development in central London spanning Moorgate tube station. It required the installation of both the highest loaded bearing piles and the highest top loaded static pile test ever undertaken in the UK, at 50.5MN (5,680 tons). The 17-storey building is founded on only 15 large diameter bored piles installed through the roof of the live station. The piles are located in two parallel rows 50 m (164 ft) apart, bridging the underlying train lines and the Crossrail tunnel below. This unique project required a diverse cross-section of skills and experience from the Project Team as we not only pushed the boundaries of design but also those of construction practices. Our team therefore needed to be made up of members from multiple businesses and disciplines. The team worked together, in a highly collaborative environment, for around two years before any work started on site. A key challenge for this project was that there was only one opportunity to construct each pile. If a position had to be abandoned there were no alternative locations and the impact on the project would have been catastrophic. It was therefore vital that all events that may have led to the abandonment of a pile were investigated ahead of commencement on site. Risk elimination and mitigation strategies were developed for all eventualities whether they be associated with the design or construction processes. The successful pile load test, coupled with all contract piles being fully instrumented with state-of-theart fiber optic (CemOptic) cable along their full length, has improved our understanding of the performance of such large and heavily loaded piles. The works piles will all be monitored during the construction of the new building, providing new insight into their real-world performance. Such groundbreaking work has never been undertaken before in the UK and has the potential to significantly influence the industry’s understanding of pile behavior, and design, in the future. This paper will discuss the challenges the team encountered during the design and construction of this highly complex urban project, particularly when adopting, by necessity, a pioneering approach.

By Eleonora Di Mario, Colin B. Turnbull, Matthew G. Mills, Chengbin Miao, Wilhelm S. Degen

"In the past decade, the ‘zero-dredge’ philosophy has become the preferred option for the formation of marine seawalls and reclamations, compared to the partially or fully dredged options, as this solution presents several environmental advantages. Recent relevant project experience is presented herein in order to highlight key design principles and construction issues central to the successful construction and performance of a sloping rubble seawall founded on soft soil improved by stone columns. If designed and installed with proper quality control, correct treatment intensity and sensible construction staging, stone columns are a safe and cost effective method for seawall foundations. This paper provides guidelines with regards to the design, construction and quality control for the correct implementation of stone columns as a foundation element for sloping rubble marine seawalls.INTRODUCTIONBenefits of sloping marine seawalls founded on stone columnsTo suit the current environmental requirements in Hong Kong, recent projects are tending to favour zero-dredge solutions, such as the Hong Kong Boundary Crossing Facility and the forthcoming Three-Runway System. The installation of stone columns allows the underlying deposits, generally consisting of very soft to soft clay and silt (soft soil), to improve in strength to the extent that the seawall can be directly placed on the seabed. This negates the need to dredge the soft soil and, therefore, this ground improvement technique represents an ideal solution for zero-dredge projects.Stone columns can also provide several other beneficial effects, including: accelerated drainage, reduced settlement, increased slope stability and soil reinforcement in the event of an earthquake. Stone columns, in contrast to competing cementitious methods, are a very ductile foundation method. This ductile behaviour is part of the design concept of stone columns in soft soil. Past projects located in Hong Kong and elsewhere, with an improved soft soil layer thickness of over 15m, have shown that stone columns can remain fully functional in terms of both drainage and horizontal reinforcement, even after settlements of over 3m and lateral displacements of up to 1m have occurred."

Jan 1, 2017

By David Guy, John Stanbury, Gilbert Tallard

"In 2009, storm surge from Hurricane Sandy inundated the Bay Park Sewage Treatment Plant located at El. +4 to +12 (+1.2 to +3.6 m) in East Rockaway, Long Island, NY. With all systems down, raw sewage water mixed in the floodwaters. A recurrence of such an event being unacceptable, and in view of rising future sea levels, a flood protection project was developed by Nassau County with funding coming in large part from the federally funded Sandy Rescue Fund. Designed by Arcadis/Hazen & Sawyer Engineers J.V., the protection took the form of a perimeter barrier capable of withstanding future storm surge. Due to limitations imposed by property lines and existing facilities, a levee design with three different types of cross section was developed to adapt to each location, adding construction complexity. The Long Island subsurface is characterized by beach sand extending to great depth. The clay required for the core and levee cover therefore had to be brought in from out of state. A thin silty clay layer at El. -23 to -25 (-7.0 to -7.6 m) served as an aquitard. The under-seepage was reduced by a hanging cut-off wall designed as a vibrated beam thin wall and filled with a salt water resistant, low permeability, self-hardening slurry.INTRODUCTIONOn October 29, 2009, Hurricane Sandy hit New York City, with a devastating effect on the region. The low lying Bay Park Sewage Treatment Plant (STP) (Fig. 1) serving Nassau County on Long Island was submerged (Fig. 2). All basements and underground mechanical facilities were flooded (Fig. 3) and millions gallons of effluent were released into the waters of the nearby Hewlett Bay which connects via other small waterways to the Atlantic Ocean."

Jan 1, 2016

Jan 1, 2001