Search Documents

By Amr M. Sallam

In recent years, with the increase of the number of high-rise buildings that are proposed and being built in Central Florida especially in Downtown Orlando, Augered Pressure Grouted Displacement (APGD) piles became a pronounced foundation option. The APGD pile is a bored displacement pile that does not result in drilling spoil. APGD piles are mostly suited for loose to medium granular soils and slightly silty/clayey sandy materials, such as those encountered in Central Florida. The case history presented in this paper involves the APGD piles recommended for a 35-story mixed-use condominium in Downtown Orlando. The subsoil condition was typical for the region; that is loose to medium fine sands underlain by thin layer of plastic sandy clays and plastic clays followed by mixed clayey sands and sandy clays with phosphates and traces of shells transitioned to the weathered limestone. Four APGD test piles were installed and were, statically, tested. Three of the tested piles failed to support the design load. Analysis of load test results showed that the bottom half of the test piles, below the plastic clay deposits, was not effective, which was attributed to structural deficiency resulted from possible pile necking due, in our opinion, to the increase of the porewater pressure within the plastic clays. Three additional test piles were constructed with modified reinforcement cage; that is to extend beyond the plastic clays with tighter stirrups. The additional test piles were, statnamically, tested and were able to sustain the design loads. The construction of the APGD piles through subsoil conditions similar to those of Downtown Orlando, where plastic clayey deposits are encountered, should account for the high porewater pressures that mostly will be developed within the plastic clay, hence, may cause pile necking. Extending the cage to penetrate through and pass the plastic clays reduced the necking potential and improved the test piles performance.

Jan 1, 2006

By Daniel J. Rider

In 1980 the Niagara Frontier Transportation Authority contracted for three miles of cut and cover box structure and station construction in Main Street, Buffalo, New York. Project depths ranged from 30 feet to 60 feet below street grade. Soils, Figure No. 1, consisted of loose to very compact sands and gravels. Ground water level was generally 20 feet below grade. Specifications required a soldier pile and timber lagging support system with external dewatering. Soldier piles were to be installed in prebored holes with bentonite slurry and lean concrete backfill. Conventional pile driving was not allowed due to concerns over excessive noise and vibrations and its effect on nearby historic structures and the surrounding population

Jan 1, 1987

By Marius B. Wechsler

There are considered deep piles which are fixed in blocks of rotating machinery foundations. A mathematical background is developed for determining the behavior of this kind of piles for motions caused by horizontal and vertical oscillations, as well as by roc-king and twisting. It is assumed that the piles come across a top soil layer of depth c, not capable of lateral support, and penetrate over a length b, in a bottom firm soil layer, or in a bottom soft soil layer in which vibrations can produce voids around the piles. With respect to b and c, as well as to the elastic properties of piles and soils, the analysis leads to the maximum bending moments and shear forces subjecting the piles, to the maximum lateral bearing on the bottom soil layer, as well as to the deflection of the pile and the displacement of the foundation block. The results of the performed analysis can be applied to seismic loads too, and they are illustrated by a numerical example.

Jan 1, 1987

By Brian Langdon

The DRIVEN GROUT PILE was developed in 1989 by DeWitt Construction, Incorporated. This piling essentially consists of a cost-in-place concrete piling that reacts on a steel boot that is driven to bearing. This report will describe the driven grout pile, its background and its installation. The advantages and disadvantages of this system are also discussed. Finally, the results of actual field installations are presented and discussed. BACKGROUND The DRIVEN GROUT PILE was developed out of a need for a low-cost high capacity piling (100 ton) that could be installed with ordinary pile driving equipment. This search was motivated by attempting to incorporate the material economy of an auger-cast piling with the "empirical load test" of a driven pile. Typically, the least cost material for piling in the 100 ton range is concrete (grout). A grout shaft with minimal reinforcement can withstand a compressive load of 100 tons for a material cost in the range of $6.00 to $8.00 per lineal foot. A pipe piling with a capacity of 100 tons has a unit material cost ranging to $13.00 per lineal foot. The marriage of these two advantages resulted in the DRIVEN GROUT PILE. A pile that utilizes the economy of a reinforced grout shaft and has the loading confidence of a driven pile.

Jan 1, 1990

By Eiji Kojima

In this research, dynamic and static load tests were performed on permanent foundation piles which had a pile length of 30 m, 800 mm in outer diameter and 15 mm in wall thickness. In this site the dynamic horizontal load test on a smaller test pile, 12 m in length, 500 mm in outer diameter and 12 mm in wall thickness, was also carried out. The static horizontal load versus horizontal displacement derived from the dynamic load test conformed well to that measured in the conventional static horizontal load test of the pile with 800 mm diameter. Then an attempt was made to predict the horizontal load displacement of the pile with 800 mm diameter based on the results of the dynamic horizontal load test of the pile with smaller diameter of 500 mm.

Jan 1, 2006

By M. D. Khattar

The paper describes the salient construction features of the Pile foundation work for the Railway viaducts in Algeria. Six viaducts were constructed for execution of the Railway line between Aintemouchent and Benisaf in Algeria. The work was executed by the Indian Railway Construction Company Limited of India (IRCON) for the Algerian National Railways (S.N.T.F.). These six viaducts had multiple spans of 36M resting on hollow piers of heights upto 69M. Most of the piers were founded on piles of 1 and 1.2M dia bored piles going upto 22M deep through cal­careous rocks and were designed for Railway loading in seismically active area. The work involved 356 piles & constituted a very important aspect of the whole work. The concrete in the piles was made with sulphate resistant cement and the integrity of the concrete was tested with Sonic method so as to ensure the quality. The piles were driven with the help of a hydraulic oscillator and the concrete was laid with a tremie pipe. Problems as encountered during execution have been explained.

Jan 1, 1989

By L. C. Reese

? Good construction and inspection presumed. ? Capacity-computation factors are independent of construction method. ? To account for variable or uncertain site conditions, anticipated construction problems, and/or minimal inspection, increase factor of safety. ? Conduct load tests and/or develop easily implemented design alternates (e.g., straight shaft in case bell can't be formed) to reduce factor of safety.

Jan 1, 1988

By Lin Daoyi

In this paper, we have adopted the high pressure jet-grouting curtains to seal the sea-water, and to consolidate the wall of the well for deep foundation diteh, make a pladge of building and construction of deep foundation was primarily on progress without water. This paper, we have been given a test for pumping water under mainly the circumtances of sealing condition and to report in advance the capacity of seawater seeping into the gam curtains in the process of building and construction of deep foundation.

Jan 1, 1991

By William F. Anderson

A series of pile load tests (maintained load tests, constant rate of penetration tests at different rates, and statnamic tests) was carried out on an instrumented model pile installed in clay beds prepared by consolidation of a slurry in a calibration chamber. The total load, shaft resistance and end bearing during the pile load tests were investigated. Following this, alternative methods of deriving the static load-settlement curve from a Statnamic test in clay taking into account damping effects have been proposed. These methods have then been used to interpret a statnamic test on a full size instrumented pile installed in a stiff glacial till.

Jan 1, 2006

By K. Viking

This article deals with some of the civil engineering related problems to be encountered when offshore wind energy projects transform from prototype offshore wind energy converter farms, developed and installed during the 1990?s, to commercial farms that?s currently planned to be built. The offshore wind energy converter (OWEC) installations encounter a wide range of problems, only partial of these are geotechnical. In Europe both onshore and offshore wind farms have, from a historical point of view, usually been founded by using the monopole technique, installed with traditional impact hammers, or by using gravitational foundations. However, the rapid development of bigger turbines and larger wind farms, together with increasing considerations of fatigue aspects, has lead to financial benefits of developing and exploring other foundation techniques. This paper reviews some Scandinavian experiences regarding critical components of the design phase in relation to connecting the superstructure to the ground, and some of the main considerations of how the loads applied to the structure are transferred to the surrounding soil.

Jan 1, 2013

By Luca de Sanctis

The analysis of piled raft foundations in layered soils may be performed by 3D finite elements or by approximate procedures. Among the latter, the code NAPRA (Russo, 1998) is based on the method of the interaction factors and accounts for soil layering by the so called Steinbrenner approximation. A comparison between the results of 3D FEM and NAPRA for some reference layered soil profiles shows that the approximation is fully acceptable for engineering purposes, provided the stiffness of the single pile is properly selected. The interest of the conclusion lies in the fact that the amount of work needed to model a practical problem by NAPRA is but a fraction of that needed by FEM modelling.

Jan 1, 2002

By K. Viking

This article deals with some of the civil engineering related problems to be encountered when offshore wind energy projects transform from prototype offshore wind energy converter farms, developed and installed during the 1990's, to commercial farms that's currently planned to be built. The offshore wind energy converter (OWEC) installations encounter a wide range of problems, only partial of these are geotechnical. In Europe both onshore and offshore wind farms have, from a historical point of view, usually been founded by using the monopole technique, installed with traditional impact hammers, or by using gravitational foundations. However, the rapid development of bigger turbines and larger wind farms, together with increasing considerations of fatigue aspects, has lead to financial benefits of developing and exploring other foundation techniques. This paper reviews some Scandinavian experiences regarding critical components of the design phase in relation to connecting the superstructure to the ground, and some of the main considerations of how the loads applied to the structure are transferred to the surrounding soil. Keywords: Offshore Wind Turbines, Wind Farms, Foundation, Pile, Gravity Structures

Jan 1, 2005

By Tianfei Liao

Extensive site investigations revealed that abandoned shallow mine workings exist under a site planned for construction of a major new facility. Since the mine voids were susceptible to collapse, they were stabilized by grouting. After completion of the mine remediation, three types of deep foundations (micro-piles, auger-cast piles, and drilled piers) were considered for this site. Micro-piles spread the load via the bond between the pile and the bedrock. Without significant length socketed in rock, the axial load of auger-cast piles and drilled piers has to be concentrated on end bearing. Although spreading the load is preferable in this environment, economic consideration dictated the choice of drilled piers for construction.

Jan 1, 2009

By D. M. Milovic

On the basis of relatively large number of field load tests of piles, the determination of the ultimate bearing capacity have been studied. Using the load settlement curves and the results of the cone or standard penetrat­ion tests, the ultimate bearing capacity was determined by Van der Veen?s, Mazurkiewicz?s and bilinear approximation method. Also, the evaluation of the modulus of deformation and the unit skin friction has been discussed.

Jan 1, 2010

By Evelio N. Horta

The influence of soil improvement replacement area in foundation settlements is discussed for soil improvement methods used in Southeast Florida. A 3D Finite element analysis is used for two typical conditions in the area: foundations bearing on loose sands and foundations bearing on a crust of limestone underlaid by very loose sands. Particular attention is given to Jet Grouting as a soil improvement method. The potential impact of the stiffer jet grout columns on the structural foundation design and quality control issues are also discussed. It is shown that in loose sand conditions 15 to 20% area replacement produces substantial reduction in total settlements. Reduction in total settlements for mixed profile is less significant but the use of the method in those cases is directed to reduce punch through potential.

Jan 1, 2007

By S. Narasimha Rao

Bored cast in situ piles are highly susceptible to construction defects like necking, discontinuity in concreting, poor compaction of concrete, improper end bearing condition due to inadequate cleaning of bore hole, exposure of reinforcement, segregation of concrete etc. There is a necessity to understand the behavior of piles so as to design effective foundation system. In this paper investigations of two field cases were discussed to bring out the effect of defective piles. In one case improper end bearing has been discussed for a concrete pile of length of 45m and diameter equal to 1.2 m and is reinforced with 32 no's of 28mm diameter steel bars and in another case necking of the pile has been discussed. Further model piles with preformed defects have been tested in laboratory to bring out the influence of defective piles.

Jan 1, 1996

By Paul J. Axtell

Two new railroad bridges in Kansas City, Missouri are founded on drilled shafts embedded into the soil and underlying shale. The uncertainty arising from the non-homogeneous, anisotropic nature of most shales, and the variability of shales across the U.S., makes it a difficult material to assign appropriate design properties. As was the case on this project, the uncertainty of foundation performance in shale can lead to overly conservative designs, particularly with drilled shaft foundations. An extensive Statnamic axial testing program was performed to verify that the load-settlement behavior of the drilled shafts would be acceptable for the intended railroad traffic. Axial Statnamic testing was applied in three increasing cycles of 927 kips, 1007 kips, and 3177 kips, respectively. The maximum movements recorded at the shaft head during each of the loadings were 0.052 inches, 0.062 inches, and 0.257 inches, respectively. The loads applied in each of the respective Statnamic tests were not sufficient to reach the capacity of the shaft; so direct comparison of measured and calculated capacities is not possible. However, evaluation of the estimated design capacity can be accomplished based on results from the Statnamic testing program by utilizing normalized load transfer relations presented by O?Neill and Reese (1999). Such comparisons necessarily require extrapolation of the data measured in the Statnamic tests following typical load-displacement response. Results indicate the Kulhawy and Phoon (1993) method for estimating side resistance in Pleasanton shale rock sockets, assuming a smooth socket, appears to agree well with observed behavior during Statnamic testing. Accordingly, the O?Neill and Reese (1999) method for estimating the toe resistance in intermediate geomaterials, assuming cohesive rock with Rock Quality Designation (RQD) between 70 and 100, appears to agree well with observed behavior during Statnamic testing. Finally, based on Statnamic testing at varying load magnitudes and normalized curves developed by O?Neill and Reese (1999), the contribution of side resistance to the capacity of a deep foundation can be determined assuming no load is transferred to the base of the foundation during lower magnitude testing. Furthermore, higher magnitude testing can provide a means to evaluate the accuracy of design end bearing calculations.

Jan 1, 2006

By M. J. Preim

Two case histories are presented on the evaluation of static bearing capacity of piles driven in soils that exhibit time dependent strength changes. Under consideration are a steel and a concrete pile driven into soils generally consisting of silty and clayey fine sand. Pile dynamic measurements and analyses were performed on both piles during initial installation, and also during restrike one week later. This information was used to predict each pile's long term capacity (defined as 14 days after initial drive), which was then compared to that measured with a static load test. Agreement between predicted and measured capacities were remarkably good, with an average error of only 4.5 percent. Two weeks after driving, total pile capacities were three times those at the end of drive. If only the skin friction was considered, however, it increased by an average factor of 16. The increase in pile capacity was determined to be linear over the time period considered.

Jan 1, 1989

By Felix Cheng

Extensions to the Convention Centre in Adelaide, South Australia consisted in part of construction over the existing railway system comprising nine rail lines and passenger platforms. Vibro-pile (Aust) won the design and construct tender with a solution comprising over 500 cast insitu concrete piles. The pile types were 500 to 900mm diameter non-displacement CFA piles and 400mm diameter displacement V-piles. The V-pile is a cast insitu screw pile developed by Vibropile (Aust) Pty Ltd. Both pile types were installed with minimal noise and vibration required for the project, while the displacement V-pile had the advantage over the CFA pile by developing the same pile capacity but with a smaller diameter and with minimal spoil. The latter was important in alleviating spoil removal problems near the railway tracks and disposal of potentially contaminated spoil. The results of dynamic compression load testing and static lateral load testing indicated that the performance of a 400 mm V-pile was equivalent to a 500 mm CFA for this site. The lateral load testing indicated that the surficial soils have a major influence on the load-deflection response, but despite the site containing up to 4 m of filled ground, the piles were found to carry the required lateral loads satisfactorily.

Jan 1, 2002

By D. A. Bruce

The use of small diameter cast-in-place bored piles is becoming increasingly popular in the United States. Such inserts are used as conventional load bearing piles, and are generally referred to as pin piles. The other major application is for the in situ reinforcement of soil slopes or excavations. The paper reviews the applications, construction, design and performance of inserts of each type.

Jan 1, 1989