Search Documents

By Frank Rausche

Why testing What tests can be done Dynamic load testing Loading device Measurements Analysis Examples

Jan 1, 2001

By Rudolph P. Frizzi

The current trend of increasing augered cast-in-place (ACIP) pile diameter, length, and load carrying capacities demonstrates improvements in installation equipment, increased acceptance, and that quality control is being successfully implemented by the parties involved in the ACIP pile construction process. Quality control is essential for ACEP piles since 24- to 36-in-dia (610-to 915-mm-dia) piles are currently being constructed to sustain design compressive loads of 800 to 900 kips (3555 to 4000 kN). This paper presents a summary of ACIP pile quality control procedures and methods beginning in the design and bid process, through ACIP pile installation, to post-construction. The results of a recent survey of contractors, engineers, equipment suppliers, and researchers routinely involved with ACIP piles in the United States, Europe, and the Middle East are included to address current trends in ACIP piles and quality control.

Jan 1, 2001

By Chaz Weaver, James Sheahan, Michael Mo

"The Virginia Department of Transportation (VDOT) undertook a program to replace four bridges along approximately 4 mi (6.4 km) of US 340 in Northwest Virginia. Two of these bridges, which span Compton Creek and the Norfolk Southern Railroad respectively, are the subject of this article. HDR provided roadway and structural design as well as geotechnical engineering services for the Norfolk Southern Railroad Bridge while their subconsultant, Saeed Associates, provided structural engineering services in support of the HDR roadway and geotechnical team for the Compton Creek Bridge.The project is located in the Valley and Ridge Geologic Province of Virginia, on an alignment that is adjacent to the Shenandoah River. The project lies within the Beekmantown Group consisting of limestone and dolostone that are prevalent and prone to karstic activity in a band that passes through the project area and north into Central and Eastern Pennsylvania. This area has been impacted by karst limestone conditions where caves and sinkhole activity is common. Caves at Luray and Front Royal, located to the south and north of the project, respectively, are popular public attractions.Since the potential for variability of subsurface conditions can be, and often is, greater in karst terrain, the need to develop a design that provides as much flexibility as possible during construction, and then to be prepared to efficiently review and respond to construction questions is heightened. Coordination and communication among the design staff, VDOT’s design and construction staff, and the contractor was a key factor in completion of this project.Compton Creek BridgeThe alignment for the new Compton Creek Bridge is located about 125 ft (38 m) west of the existing bridge, placing it between that bridge and the existing Norfolk Southern Railroad Bridge. No information about the foundations was available for the existing bridges. Borings in the Compton Creek valley encountered extensive voids (some clay filled and some open) with numerous boulders, rock ledges and pinnacles, particularly on the north side of the creek. Geophysical and geotechnical investigations indicated that below a poor and variable upper zone of rock was a layer of more competent and consistent limestone, which appeared to contain little or no voids."

Jan 1, 2017

By Dan Brown

Improvements in construction equipment and techniques in recent years have made possible the use of drilled shaft foundations in diameters and lengths not previously considered practical or feasible. Many highway bridge and other structures are now routinely founded on drilled shafts which are 8 to 12 feet in diameter and extending over 200 feet in depth below grade. There are unique challenges associated with constructing such large and deep cast-in-place foundations and engineers should be aware of the special needs associated with site investigation, construction specifications, material requirements, and quality assurance. This paper outlines a number of special considerations for these foundations, along with strategies that may be employed to improve the reliability and quality of large drilled shaft foundations.

Jan 1, 2013

By Mario Mauro

Tuttle Creek Dam was constructed by the U.S. Army Corps of Engineers in the 1950?s on the Big Blue River in north-east Kansas. Since the dam is located in a seismic area, the safety of the dam was re-evaluated under the national U.S. Army Corps of Engineers Dam Safety and Assurance Program. After a series of studies and analyses performed by the Kansas City District of the U.S. Army Corps of Engineers, in 2003 the Department of the Army authorized the implementation of the plan ?Stabilize Foundation Soil without Drawdown Alternative?, during a 7-10 year construction period. As part of this plan, in 2006 Treviicos South carried out a large scale jet grouting and deep mixing test program downstream the dam. The test program included the installation of twenty-seven double and triple-fluid jet grout columns and twenty-seven jet-assisted deep mix columns. The jet grout columns were constructed at different levels of specific energy and cement content. The deep mix columns ranged in diameter between 3 ft and 6 ft. During column placement, the drilling and grouting parameters, pore pressures, and soil movements were instrumented in real-time. The downstream test area was enclosed by a cement-bentonite wall extended to bedrock, which allowed a 35-ft deep open excavation around the 45-ft deep columns. The exposed jet grout columns measured up to 15 ft in diameter, exceeding the anticipated target diameter. In addition to coring, some of the jet grout and soil mix test columns were saw-cut along the group axis, providing useful information on the internal column structure.

Jan 1, 2008

By Alan Alhadeff

Why is mediation being hailed as the wave of the future? The high cost of putting on a trial, over-crowded court calendars and long trial delays have resulted in what prominent attorneys and leading jurists are calling a litigation crisis. In no segment of the legal world are these pressures greater felt than in the trial of the serious construction case. Furthermore, the siege mentality of both the plaintiff and defense bar often leads to a reluctance by either side to make the first reasonable offer for fear of showing weakness. Attorneys operating in the serious construction case arena express concerns that there exist insufficient opportunities for the parties to meet, tell their stories, and negotiate settlement prior to the eve of trial. Mediation, by opening lines of effective communication and encouraging meaningful settlement negotiation, has proven to be a very effective antidote to the litigation crisis.

Jan 1, 1990

By Osama A. Safaqah

Driven plate anchors can be used to hold in place large bridge caissons during floating construction. Their small size and simple method of installation make them a very cost effective alternative to other direct-embedment, gravity, and drag anchors. The geotechnical design of plate anchors involves the anchor geometry, embedment, drivability, and proof testing. This paper describes the experience gained with plate anchors used during construction of the new Tacoma Narrows Bridge. For this project, the anchors had to be driven in dense to very dense sands, and had to resist large forces from 7-9 knot currents.

Jan 1, 2013

By Joel L. Volterra

Since 1910, Mueser Rutledge Consulting Engineers (MRCE) has regularly provided professional engineering services including inspection of pile load tests. Historically, such services included on-site inspection of the driving of test piles and subsequent static load tests by qualified Geotechnical Engineers. Load testing procedures are specified by local or State Building Codes, locally the 1968 Building Code of the City of New York (1968 BCCNY). Between 1968 and 2008, the 1968 BCCNY required a minimum 48-hour hold period for standard loads per pile type, an extended 96-hour hold period for higher capacity piles, and a settlement criterion that the pile maintain a test load equal to two times the design load with less than 0.012 inches of settlement over the last 48 hours of the hold period. Effective July 2008, the new 2008 BCCNY shortened the hold period and relaxed the settlement criteria to that which is more similar to other governing codes and standards such as the International Building Code (IBC 2006) and the American Society for Testing and Materials (ASTM). MRCE implemented an automated load test monitoring system to reduce costs and to alleviate or minimize overnight and off-hour staffing for load test readings. Initially, a series of linear variable differential transformers (LVDTs) and data loggers were included in the Contractor?s load test setup to electronically record pile head settlement and where applicable, settlement of telltales installed to varying depths in the pile. A pressure gage was subsequently added in the hydraulic line, then a load cell, strain gages, and remote access using modems. The ease of the setup and modular adaptive nature of this system have proven it to be a useful tool and improved our ability to better serve our clients and manage our pile load testing services.

Jan 1, 2008

Jan 1, 1993

By Dennis Nottingham

The need for deep compaction of submerged granular soils has led to improvements in this area. In 1971, L.B. Foster Company personnel patented a method of deep compaction using a vibratory pile hammer and pile probe. The technique had some success, but did not produce consistent results and thus found its way to obscurity. Other patents attempted to modify the technique by various probe modifications, but again without measurable improvement from a practical point of view. Solutions to economical deep compaction up to 100 foot depths particularly in saturated granular soils would have a great impact on the construction industry and new bulkhead structures being developed, thus PND was prompted into related research and development. The advent of higher horsepower vibratory hammers, coupled with PND engineers? experiments, observations and measurements, led to an ?H? pile probe design which has produced measured soil density improvements up to 250% using SPT ?N60? values as a measure.

Jan 1, 2013

By Silas C. Nichols

FHWA Interest is due to: ? An increase in successful projects in the U.S. private sector and in other countries ? Cost effective and more efficient in many circumstances ? Agency Priorities - FHWA "Vital Few" AASHTO TIG

Jan 1, 2005

By Frank Rausche

Introduction and Background Testing -Pile Preparation -Data Processing -Data Interpretation/Case Studies Case Studies - Existing Piles Stories from around the world

Jan 1, 2001

By Ashraf M. Eid

Most research dealing with the problem of laterally loaded piles has been the response of individual piles subjected to lateral loads and/or bending moments. However, piles are seldom used individually but are normally constructed in clusters or groups. Little information is available of the effect of pile-soil-pile interaction (PSPI) on the performance of the group. This may be attributed to the difficulty of carrying out full-scale tests. Such tests are prohibitively expensive and require special installations to provide the required large lateral loads. The problem of laterally loaded single piles or pile groups involves the complexity of extending the theoretical solutions to the limits where the actual soil behaves nonlinearly. As the load increases, the elastic soil behavior cannot be adopted for design. Nonlinear soil behavior or the elasto-plastic behavior is evident. This research consists of experimental and theoretical models. The experimental work was conducted on models of free head pile groups in different configurations. The piles were in a sand formation and compared to the behavior of a single pile. The possible factors that influence the group behavior could be visualized. The experimental data was also compared to the widely used theoretical approaches to determine their adequacy. The analytical model makes use of the finite difference approach to calculate the soil non-linearity. A new approach equates the measured ground deflection and maximum bending moments of each row at every load level with the analytical model of single pile. This is the Deflection-Moment Fitting (DMF). The most suitable non-linear soil modulus modes and row contributions could thus be determined. Design of pile groups can be based on data pertaining to soil characteristics of the single pile. Results of the analysis were consistent with other approaches and proved to be adequate for design.

Jan 1, 2005

By Amr M. Sallam

A case history of utilizing a mat foundation enhanced with ?settlement-control? piles to support a high-rise building in Downtown Orlando is presented. Original geotechnical engineering studies, performed by others, recommended pile foundations due to difficult soil conditions and highly variable loads. The value engineering study performed by the authors provided alternative foundation system of the mat foundation enhanced by ?settlement-control? piles. The alternative foundation system required few iterations of structural and geotechnical analysis. A target stiffness for the settlement-control piles was selected by the structural engineer. Pile load tests were performed to verify the recommended pile geometry. A total of 81 auger-cast-in-place settlement-control piles 45-foot long 16-inch diameter were installed. A total of 24 columns were monitored for settlement, which showed substantially less settlement than predicted. It is the authors? opinion that the ?settlement-control? piles increased the mat stiffness, relieved the concentration of contact pressures around heavily loaded columns, and reduced potential differential settlement. Mat foundation with settlement-control piles provided border-line foundation solution between shallow and deep foundations and has the potential to be widely used in Central Florida for similar subsoil and loading conditions; however a thorough analysis using three dimensional Finite Element Modeling may be needed to refine the geotechnical evaluations.

Jan 1, 2009

By Alice Y. Tseng, Dan MacLean

"Corrosion protection of all deep foundation systems made of steel is THE issue when considering durability of the element in the long term. Protecting steel from corrosion and maintaining the steel tendon cross sectional area ensures a competent and durable system. The foundation of a building is usually difficult to repair and therefore high risk is taken when unknowingly choosing a non-adequate solution.Requirements according to EN 1990 (Eurocode 0 or EC 0) on construction durability requires a service life over 100 years. How can a service life over 100 years be achieved? How shall bare steel be protected in soil, which sometimes could be an aggressive environment to the steel? Which corrosion protection methods are commonly used in Europe and in North America?This paper will focus on hollow bars used as Micropiles, Anchor piles and Soil Nails. It gives an overview about the state of the practice in regards to corrosion protection (including head construction) and evaluates different options following the European Standards focusing on type of material and method of installation. Further the different corrosion protective methods such as thickness of grout body, coating types and sacrificial loss are listed with the pros and cons evaluated.Based not only on North American standards like FHWA “Micropile Design and Construction Guidelines”, FHWA Geotechnical Engineering Circular No. 7 for “Soil Nail Walls“ and Post-Tensioning Institute “Recommendations for Prestressed Rock and Soil Anchors”, but also European standards like EN 14199 “Execution of special geotechnical works – Micropiles”, EN 14490 “Execution of special geotechnical works - Soil nailing”, EN 1537 “Execution of special geotechnical work – Ground anchors“, and other relevant standards, all possibilities of protecting the hollow bars and the steel quality will be introduced, discussed and compared ."

Jan 1, 2017

By C. M. Haberfield

"1 INTRODUCTION Around the world, there is a demand for larger structures, tall buildings and large bridges. While good footing design is important for all structures, it is even more important in the case of large structures. Recent experience with footing design for tall buildings (e.g. Burj Al Alam development and Nakheel Tower in Dubai, the Gate of Kuwait in Kuwait, the City Centre Project in Bahrain and Eureka Tower and Freshwater Place in Melbourne) has shown the benefits of investing in footing planning, design and construction (Haberfield, 2011, Poulos and Bunce, 2007). The footing systems for most of these projects include the use of deep bored piles or barrettes (piles of rectangular cross-section). Many use piled rafts where the piles, while acting to support the load, are primarily used to reduce settlements. A clear understanding of the factors controlling the behaviour of the footing system is needed to enable a good engineering design to be achieved. This starts with a sound understanding of the ground characteristics and individual pile performance, including adequate collection of data and testing. The best footing solution can then be found using recent improvements in data collection and analytical techniques, complex and highly capable computer-based models and the availability of high speed computers. This paper focuses on the axial performance of deep bored piles socketed into rock – both their individual performance and their performance as part of a larger footing system. Recent research and construction practice is discussed. In practically all cases, serviceability conditions control the behaviour of the footings. Methods of establishing the parameters for input into sophisticated computer programs are described. Application of the methods to case studies is included and it is shown that the behaviour of individual piles can be closely predicted. These developments lead to lower construction costs, better constructability and shortened construction time because of the better understanding of footing behaviour. 2 FACTORS AFFECTING PERFORMANCE OF FOOTINGS ON ROCK For a typical pile-supported footing, it is necessary to consider both individual pile, pile group and raft performance. These require consideration of the behaviour of the ground immediately beneath the surface raft or footing, along the pile shaft, and at and beneath the pile toe (Figure 1). Immediately beneath the surface raft or footing, the important factors are strength for bearing capacity and stiffness for settlement and interaction effects. Along the pile shaft, of most interest are strength for bearing, excavatability and stability; stiffness for settlement and interaction effects; geology and permeability for pile stability and, most importantly, pile shaft resistance. At the pile toe all the above factors for the pile shaft are present and in addition the pile end bearing is of interest. Below the toe, stiffness for pile settlement is important to at least a depth of twice the building width."

Jan 1, 1900

By Michael W. Oakland

Weidlinger Associates was retained to evaluate the foundations supporting ten oil storage tanks at a tank farm on the east coast. The tanks were constructed over the site of a landfill which was underlain by deep organic deposits. The tanks were typically 48 ft. in height and ranged in diameter from 60 to 150 ft. The tanks were supported on both wood and steel pipe piles. After more than 35 years of service, an inspection found that up to 25 percent of the piles had separated from the mat foundation. The operations at the facility were temporarily stopped pending further investigation. Weidlinger developed comprehensive finite element models of the foundations for each tank and used random generators to conduct Monte Carlo simulations the range of scenarios of detached support conditions since it was not possible to survey all the piles below the tanks. To confirm the modeled performance and verify stability, each tank was also load tested using water with electronic instrumentation installed by Geo-Instruments. The instrumentation provided real time, web based monitoring during testing in areas which would otherwise be inaccessible during loading. Through inspection, complex modeling and sophisticated load testing, Weidlinger and Geo-Instruments were able to show that all but one of the tanks could safely be put back into service. This paper details the analysis, Monte Carlo simulations and instrumentation and load testing performed for this unique project.

Jan 1, 2009

By Kevin Kuhl

With the destruction of the US-90 Bridge spanning St. Louis Bay by Hurricane Katrina, the State of Mississippi awarded its first major design-build contract in order to have a completed four-lane bridge in a period of less than two years. The structure consists of 76 pre-cast concrete beam spans with a total bridge length from Bent 1 to Bent 77 of 11,124 ft (2.1 miles). All 77 bents are founded on pre-cast, pre-stressed concrete piles and consist of two foundation types: pile bents and water line footings. A total of 53 pile bents were utilized where the deck is less than 52 ft above the water. Further divided, 10 pile bents, supported by 24 in. square, solid piles, are located on land. The remainder of the pile bents are located within St. Louis Bay and supported by 36 in. square, voided piles. All the waterline footings are supported by 30 in. square, voided piles. In total, 138 -24 in., 437 -30 in., and 463 -36 in. piles support the structure. Production pile design was based upon information gathered from the subsurface investigation, design soil profile and 23 out-of-position test piles. Verification of the design was established by monitoring the first production pile driven at each bent using the Pile Driving Analyzer. Particular challenges included highly variable coastal deposits, loads in excess of 1600 kips per pile and a compressed construction schedule. Initial drive capacity of a portion of the production test piles was less than expected resulting in a minimum 14 day setup. Following the setup period, restrikes were necessary to verify capacity. Project production piles ranging from 50 ft in length to in excess of 160 ft in length were used to achieve the required resistance. This paper includes a brief overview of the foundation design and indicator test pile program. The main objective is to provide a summary of the quality control procedures including establishing the driving criteria for each bent and to present issues that arose during production pile driving and the solutions that followed.

May 11, 2007

By David C. Kraft

Atlas Systems, Inc. (ASI) resistance type piers were used to underpin a 100 year old historic structure at Fort Monroe, Virginia. This 3-story structure with basement was underpinned with 155 steel tubular push piers (4" OD) that were hydraulically installed to depths ranging between 90 and 110 ft. and to installing forces in excess of 60,000 lb. Project requirements included lowering the basement floor by 1-1/2 ft. and constructing new footings and adding stem walls to connect to the existing masonry walls. Additionally, the underpinning piers were temporary which required the development of a decoupling system to permit the transfer of the building loads from the underpinning piers to the new footings. The structural loads at the foundation level required a c. to c. pier spacing of 3.75 ft. in order to meet project requirements of a minimum Factor of Safety of 3.0 on the pier load capacity. Project requirements included a load test on the selected underpinning pier (ASI - AP2 4000.219) in order to establish installation depths for seating the piers to 60,000 lb. The project was successful in supporting the full load of the structure during the construction phase. Considerable savings in time and cost were achieved as well as avoiding any vibrations or noise during installation of the piers.

Jan 1, 2002

By Thomas Trochalides

Newtown Creek Water Pollution Control Plant in Brooklyn, NY is the largest of 14 Water Pollution Control Plants in New York City. It services over 1 million people with a current processing capacity of 310 million gallons daily. Upgrades to the plant have been underway since 1998. This paper details the foundation elements installed in three separate contracts during 2009: NC-41F, NC-36G, and NC-47G. The elements are Concrete-Filled Pipe Piles, H-Piles, Steel Sheet Piling, Secant Walls, Drilled Caissons, and High Capacity Micropiles. Soils on the site consist of fill over organic silty clay and silty sand. Beneath the organic layers lie lake sand and varved silt and clay, sitting atop glacial till and rock. Due to Federal Mandates, certain plant capacity and secondary treatment requirements had to be met by specific dates. Failure to meet the requirements would have an adverse affect on the NYC areas being serviced. Further complicating the project, the existing plant operations had to be maintained throughout the entire construction phase. To accommodate the constraints of the project, new specialty equipment and several key redesigns were used to maintain construction schedules

Jan 1, 2010