Search Documents

By J. E. Nesset, J. A. Finch, Rosenblum. F., S. Somot

"In a previous presentation at the CMP, evidence was shown for the formation of hydrogen sulphide (H2S) in self-heating experiments on pyrrhotite-rich samples (Somot and Finch, 2006). Oxidation of H2S is strongly exothermic leading to the proposition that H2S is playing a key role in the self-heating process. Subsequently, tests in two weathering apparatus (I and II) were run under varying oxygen levels to further examine conditions leading to self-heating. To characterise their resulting self-heating capacity the samples from the weathering tests were subjected to a modified Stage B test using the self-heating apparatus developed by Rosenblum and co-workers (Rosenblum and Spira, 1995; Rosenblum et al., 2001). Results showed highest self-heating after weathering occurs under low oxygen conditions, supporting the H2S hypothesis. It was observed that highest heating rates are not directly related to highest weight gains of samples.INTRODUCTION“Sulphides” refer to several types of minerals containing sulphur in its lowest oxidation state of - 2. Self-heating is the spontaneous heating of a material without external heat input. It is well established that some sulphides will self-heat on exposure to moisture and oxygen (Farnsworth, 1977; Good, 1977; Rosenblum et al., 2001; Wu and Li, 2005). This process is highly exothermic and if the heat generated is not dissipated, combustion may occur when the temperature reaches the ignition point of the sulphide (typically 350-400 °C). The hazards of sulphide self-heating range from handling hot material, to sulphur dioxide release, to fires. The literature documents self-heating incidents underground, on ships and trucks transporting sulphide concentrates, and in mine waste (tailing) disposal areas (Stachulak, 1990; Lukaszewski, 1969; Headley et al., 1977). Lukaszewski (1969), Farnsworth (1977), and Good (1977) note that sulphide minerals can act as fuel to promote underground mine fires. Based on such findings, sulphide minerals could become classified as hazardous materials, making transport of concentrates and storage of mine waste subject to stricter and more costly regulation. The problem is one the industry is keen to avoid."

Jan 1, 2009

By Eugen Gluck, Gus Van Weert, Peter Kondos

"Microwaves have the capability to heat up sulphides, especially clusters of particles of approx. 1 mm. Some sulphides absorb microwaves more readily than others. Molybdenite is especially effective in this regard, possibly due to its flaky nature and/or electrical conductivity. Even where it occurs in low concentrations in a deposit, individual rocks may be ore grade due to the high monetary value of MoS2. Such rocks often result from crushing mined veinlets or stockwork, or are contained in the cutoff grade fraction of ROM. Machine segregation of rocks high in MoS2 by infrared sensors after microwaving could therefore advantageously be used to upgrade lower grade ore between Mine and Mill. This would reduce the size of the latter, and thus its CAPEX and OPEX. Such upgrading could also yield shipping ore for a distant Mill, or extend ore reserves.Barrick Gold Corp. has been supporting the development of MW/IR sulphide sorting for the past three years. The results of MW/IR sorting work on molybdenite and other (pyritic) ore samples from a variety of sources are being presented here.INTRODUCTIONThis paper looks at mechanized, i.e. machine ore sorting technologies currently available and under development, and what conditions would be needed for the potential application of such ore sorting to sulphide mining and milling. Current machine sorting involves no-contact sensing technology for rocks, and signal processing after sensing to activate airblast segregation of certain rocks, normally the smallest mass to keep compressed air costs down.The forerunner of modern sorting is probably magnetic separation, which utilizes an inherent property of certain ores to divert it into mag and non-mags fractions. Radiometric ore sorters, which have been applied successfully for decades in the pre-concentration of uranium ores (Wotruba and Riedel, 2006) initiated modern sorting. In the 90’s, sensor-based machine sorting became a viable means of increasing the overall economic recovery of a resource. This technology became driven by the availability of low cost computing equipment and the concurrent development of algorithms, and by the availability of extremely fast response sensors and air actuators, allowing the sorting equipment to run faster, dropping the cost per tonne. It has been in industrial minerals processing that rock sorting has been most widely adopted, not really surprising. Liberation occurs on a different scale than in the base metal industry. Most industrial minerals are mined from massive deposits, requiring (in the past) no upgrading. Many of these operations now run into product contamination problems, which ore sorting can solve. One illustration: in Finland, a quarry is separating limestone from dolomite at 500 tonnes / hour, with individual rocks weighing up to 15 kg. Many of these industrial minerals operations have stockpiles of earlier discarded below-quality rocks, now being reprocessed with the help of ore sorting. The economics of this are very favourable, going from zero or negative value (stockpiles can not be left when closing the mine) to full product value for at least a portion of the stockpile. This suggests that in the future the economics of overburden sorting could become attractive under the right circumstances and such treatment could well become an integral part of open pit mine development."

Jan 1, 2009

"Drilling twinned holes is a traditional technique used for verification of intersections of high-grade mineralization, testing of historic data, or confirmation of drillhole data during geological due diligence studies. Twinned holes can also be used for special tasks such as correcting earlier data that are recognized to be biased. Successful implementation of the twinned-holes technique requires thorough planning. Experience suggests that good practice is to drill twinned holes no more than 5 m apart. Many unsuccessful twinned-holes programs could possibly have failed because the twinned holes have been drilled too far apart.Twinned holes are best compared by mineralization intersections and, if the data and geological characteristics of the deposit permit, by samples, equal-length composites, or geological units. Variables to be verified by twinned holes should include the thicknesses of the geological units of interest (e.g., mineralized thickness) as well as the presence of significant geological features (e.g., ore/mineralization contacts, alteration, etc.).A formal, rigorous analysis of twinned-hole data is essential. Repeatability of sampling, analytical results, and bias must be analyzed and statistically quantified. The number of twinned holes required for conclusive statistical and geostatistical analysis can be as high as 20-30, in particular where the studied variables are characterized by high short-range (local) variability.The efficiency of this approach is demonstrated by several examples of successfully applied twinned-hole projects, including applications to orogenic gold, mineral sands, bauxite, and iron ore deposits."

Jan 1, 2009

By Jesse L. Duke

Outline ?Understanding the context ?The Business, political, social and legal environment ?Recipes for Success (three Ps) ?Develop effective Partnerships/relationships ?Plan carefully ?Actively Manage the ?Process? Business Environment ?Nunavut?Impressive mineral potential ?Emerging diamond industry ?Dominated by Juniors ?NWT ?Maturing Diamond industry ?Emerging oil and gas industry ?Yukon ?Alaska Highway Pipeline ?Junior-dominated exploration and development ?Growing acknowledgement in Canada of the importance of northern resources ?Shift of thinking: north-south infrastructure (vs. East-west)

May 1, 2006

By Kristie Tarr

Portland cement is primarily used to solidify backfill in underground mine workings and it represents a major cost in mining operations. CANMET-MMSL has invented an alternative binder technology that does not contain any amount of Portland cement and is made using waste materials, such as development rock and smelter slag. The technology has been successfully tested with many types of base metal and ferrous slag. Research conducted in collaboration with several mining operations in Canada has shown that the CANMET-MMSL binder has considerable potential as a replacement for Portland cement in mine backfill. An integral part of the overall mining operation, backfill is used for two main purposes: safety and environmental remediation. Depending on the mining method used, backfill provides a working surface, stabilizes stope and pillar walls, as well as the surrounding rock mass, and controls caving of stope backs. There are several benefits associated with the replacement of Portland cement in backfill, including reductions in (i) the footprint by placement of slag waste underground, (ii) the environmental effects and long term liability resulting from disposal and containment of slag waste on surface such as acid rock drainage, (iii) GHG as a result of reduced Portland cement usage (the production of 1 ton of Portland cement produces 1 ton of GHG), and (iv) the significant costs associated with reduced Portland cement usage.

Oct 1, 2010

By G. A. Kosick, G. S. Dobby, O. Matwijenko

"A 100 kg/hr portable flotation pilot plant has been operated at Kidd Creek Mines with the objectives of:(a) determining performance expected by column flotation circuits on primary zinc and copper cleaning, and (b) evaluating column flotation circuit configurations.The self-supporting pilot plant, owned by Minnovex Technologies Inc. and operated by Minnovex and the University of Toronto, consisted of three 16 cm diameter by 6.5 m high columns and a bank of four Denver No. 7 cells. It was configurable to any arrangement using these four (or fewer) units. The columns were controlled through the use of multiple pressure transducer measurements. This paper presents the approach to testing and the results of more than 70 circuit tests. INTRODUCTIONThe integration and retrofitting of flotation columns within existing mechanical cell flotation circuits is becoming a common occurrence. The correct approach to this integration, however, is often difficult to define, due to a scarcity of previous experience and the difficulty in predicting column circuit performance. In most cases, the effect of column implementation has been experimentally assessed using a single pilot column, with the consequence that selection of an appropriate circuit to implement is difficult. Important considerations are the impact that column water addition will have on the existing operations, and the differences between mechanical cell and column performance in integrated cleaning circuits.To address the problem of circuit selection a portable flotation pilot plant, consisting of both columns and mechanical cells, was designed and constructed by Minnovex Technologies. The pilot plant was structured for complete flexibility of circuit configuration, with the intent to provide a means by which both research and plant personnel could determine the best possible column circuit configuration for a given application."

Jan 1, 1990

By R. F. Pilgrim

"This first chapter of the SPOC Manual 1s intended as a general introduction to all the other chapters in which the mineral process evaluation and optimization methodology is presented. This chapter also provides a brief description of available software for mainframe and m1crocomputers and provides information on its distribution by the Technology Information Division. CANMETRESUMECe premier chapitre du manuel SPOC est un guide général qui présente les autres chapitres ou l'on traite de la méthodologie d'évaluation et d'optimisation des procédés miméralurgiques. Le lecteur y trouvera aussi une description sommaire des programmes de calcul développés pour ordinateurs centraux et pour micro-ordinateurs ainsi que la façon de les obtenir de la Division de l'information technologique du CANMETComputer simulation of mineral processes has slowly emerged as an established branch of activity in A&D centres and in several teaching institutions after decades of slow progress. Substantial efforts to develop application software based on years of research on process modelling are being pursued in many countries ( 1 .2,3,4.5). The late BO's should see a flurry of success stones about significant leaps of productivity achieved in several plants through systematic process evaluation and computer simulation studies.In Canada. the SPOC project (Simulated Processrng of Ore and Coal) was initiated at CAN MET in 1980 with the obJective of developing and transferrrng to the mineral rndustry a computer-based methodology for process evaluation and optimization. The proiect deliverables include:- an engineering manual covering most aspects of off-line computer simulation:- a bank of FORTRAN software accessible through data communication lines for user familiarization and distributed at a nominal cost in source form by CANMETThe yearly progress reports of the project contain detailed information on the project elements since 1980 16). The context of SPOC can be summed up by quoting Gordon Agar""s 1975 statement during a workshop on research needs in the mineral industry: ""What is needed is a joint effort between the academic community and one or more enliglitened industrial concerns. The effort will have to be an iterative one with data collection followed by testing the model modification of the model (s), more testing prediction, modification. data collection and so on (7). A few parallel in1- t1atives had been reported in papers or research contract reports (8, 9) but there was an obvious need for CANMET to bridge the gap between the R&D and the production sectors by undertaking a project that would document past applications and induce a new generation of initiatives through the consol1dat1on and transfer of suitable manuals and software. The effort took shape as the CANMET SPOC pro1ect in which methodology transfer was to play a key role (10)."

Jan 1, 1986

By C. J. Farrow, M. J. Smith

"Bechtel has managed a number of test programs to establish autogenous grinding circuits and size mills for a variety of ores.This paper outlines the procedures whereby bench scale and pilot plant tests are used to select the most efficient circuit to grind the range of ore types likely in the mill feed.Five examples are given. One example traces the development of a pilot plant program; it shows how bench scale Work Indices provide a target for the grinding power requirement of an ore and relates how pilot circuits are changed as a result of interpreting the results from preceding tests. The other four examples relate the interpretation of the test results to provide design data; they illustrate a number of phenomena which have been observed.INTRODUCTIONConventional crushing and grinding circuits can be specified from bench scale test data such as Bond Work Indices. Bond Indices have been correlated to a large number of rod and ball mills and by applying appropriate factors, mills can be sized from the Work Index.For autogenous or semi-autogenous grinding circuits, bench scale tests are not sufficient to be able to specify the circuit and size of the mills for a commercial plant. It is necessary to run a series of pilot plant tests to determine how the ore behaves."

Jan 1, 1982

By M. W. Lewis

A mine's inherent capacity is dictated by factors such as equipment, design, people, processes, and environment. Actual production may approach, but never surpass, the inherent capacity limit. The inherent capacity ceiling can only be increased through re-engineering. Autonomous haulage systems have the potential to significantly increase a mine ’s inherent and realized capacity. Realized capacity may be maximized through the optimization of soft factors such as the processes, behaviours, and organizational systems, controlling asset utilization, availability, and performance. Truck shovel dispatching systems revolutionized the utilization of mobile assets. High-precision global positioning systems (HP-GPS) are increasingly being adopted to optimize equipment performance. Real-time maintenance management systems have the potential to revolutionize equipment availability and significantly reduce cash costs. This paper explores some of the solutions available to mines to increase their inherent capacity and maximize their realized capacity.

Jan 1, 2004

By M. W. Lewis, B. Sambirsky, J. Werner

A mine’s inherent capacity is dictated by factors such as equipment, design, people, processes, and environment. Actual production may approach, but never surpass, the inherent capacity limit. The inherent capacity ceiling can only be increased through re-engineering. Autonomous haulage systems have the potential to significantly increase a mine’s inherent and realized capacity. Realized capacity may be maximized through the optimization of soft factors such as the processes, behaviours, and organizational systems, controlling asset utilization, availability, and performance. Truck shovel dispatching systems revolutionized the utilization of mobile assets. High-precision global positioning systems (HP-GPS) are increasingly being adopted to optimize equipment performance. Real-time maintenance management systems have the potential to revolutionize equipment availability and significantly reduce cash costs. This paper explores some of the solutions available to mines to increase their inherent capacity and maximize their realized capacity.

Jan 1, 2004

By A. M. Hill

"This is an account of the expansion of Texasgulf's Timmins concentrator by the building of a fourth circuit.The original capacity of the mine and concentrator was 3.6 million tons per year of ore. In 1974, Texasgulf decided to increase that capacity by about one third to 4.8 million tons per year. It was planned that the increased capacity would be available by mid-1978.The expansion involved work at the rninesite, increased railroad capacity, and a new circuit in the concentrator, and it is the concentrator expansion which is described here.In 1974, the minesite drew its ore from the open pit. The pit was being phased out and was to be replaced by No. 1 mine. To allow for the expansion, a second mine was required. The railroad was capable of handling 18 car trains. Its capacity had to be increased to 27 cars per train and this, in turn, required two new locomotives. Each of these alone cost half a million dollars.The concentrator building in 1974 contained the concentrating equipment and miscellaneous services (such as machine shop, warehouse, analytical lab). The grinding and flotation sections were divided into three circuits ('A', 'B', & 'C'). 'A' and 'B' circuits treated copper-zinc ore and 'C' circuit treated the much more difficult copperzinc- lead ore. This 'C' circuit had been modified over the years to implement improvements in the metallurgy."

Jan 1, 1979

By Luis Castelli, Aldo Bonomelli, Giselle Schifferli, Claudio Zamora

"This paper introduces the operational concept and the description of a multi-site Remote Support Center for knowledge management and long-term process performance improvement.This centralized Support Center provides real-time monitoring of open-platform process automation systems, and on-line access to process data and control applications information for multiple sites.Considering that process automation is a key enabler to business performance improvement, sustaining effective performance benefits over time becomes essential. Unfortunately, changes in manufacturing process dynamics, technology obsolescence and in plant operational practices cause the control strategies to lose their effectiveness over time unless their performance is periodically evaluated, and if required, tuned to the new process conditions.A new concept in process automation is proposed through the addition of a new control loop based on performance analysis methodology which is intended to feedback process and automation operation information to system and process specialists, allowing for continuous manufacturing process improvement and sustainable production benefits through effectual control strategies.A remote support center can play a key role in the delivery of such services, by providing the base platform from which a comprehensive process overview and a centralized knowledge database can be executed and additionally, as an enabler for plant operational practices change.INTRODUCTIONA Benchmark on Automation Level in Copper Concentrators conducted by AMIRA in 2004, reported that the Codelco divisions scored below their peers in several categories.Codelco had thereafter been looking for a new automation concept, and had focused on process automation as a key enabler for process manufacturing and business performance improvement. The final decision was to create a strategic alliance with a world-class automation technology provider.The traditional approach based on isolated automation solutions/projects, showed that the control strategies benefits were decreasing progressively over time, because of the on-going need to adapt the control models to the ever-changing process conditions and different plant operational practices. Another consequence of this traditional approach was the wide variety of technologies and automation systems deployed in the different plant sites, with no common automation standards, and with low opportunities to transfer knowledge or practices."

Jan 1, 2010

By S. Nagamatsu

Alumina supported gold catalyst prepared by spray reaction method (spr) provides gold particle with about 20 nm of diameter. The gold particle size is larger than conventional gold catalysts. However, the spr catalyst shows higher catalytic activity for NO-CO reaction. In the present paper, we have discussed the local structures of spr-Au/Al2O3 catalyst by using Au L3-edge XANES spectra. In order to investigate the local structures of Au-sites, multiple scattering approach to XANES analysis was applied. Calculated Au L3-edge XANES spectra for fcc-Au and Au2O3 were in good agreement with the observed spectra. XANES spectra for spr-Au/Al2O3 were characterized by 4 types of Au sites (bulk, interface, surface and peripheral). In this case, almost all gold sites (> 90 %) are bulk site. The other sites are less than 10 % of gold particle. However, the experimental and the calculated results of Au L3-edge XANES spectra for spr-Au/Al2O3 require about 30 % of gold oxide or hydroxide. Bulk of Al2O3 contains a certain number of gold nano-particles, which was incorporated in the bulk Al2O3 support. In the interface area, gold oxide forms a few layers. This result was also supported by DV-Xa electronic structure calculations. The comparison of the catalytic activities of the spray catalysts and the impregnation catalyst for the NO-CO reactions imply synergy effects between gold nano-particles and alumina support.

Oct 1, 2003

By Y. Faitakis, G. J. Powley, C. Mackenzie

"In the mining industry, maintenance is a key priority and a major expense. As mining equipment is large in scale, high in cost, and difficult to tow, it is key to maintain equipment on a timely basis. Breakdown in -40°C or away from a maintenance station can cause great costs in repair as well as lost production.It has often been quoted that about 5% of the North American production is lost every year due to unscheduled downtime. About onethird of the downtime is attributable to equipment failures. From this fact alone, it is evident that proper equipment maintenance can add tremendous value to the bottom line. As organizations and equipment become more sophisticated, maintenance expectations begin to evolve. This evolution can be traced through three generations:The first generation (1940–1950): A “fix it when it broke” attitude prevailed during that time, mostly because the industry was not highly automated.The second generation (1950–1980): Automation and mechanization of the industry increased. The industry now was dependent on machines performing the majority of the work. Preventive maintenance (overhauls at fixed intervals) appeared as the first maintenance practice. Maintenance costs started to rise rapidly.The third generation (1980–): Assets become more complex. Failure modes are better understood and computerized maintenance methods are becoming mainstream. Condition-based maintenance (CBM) starts to gain ground as a cost-effective alternative, replacing the fixed interval overhauls. As corporations amalgamate and market places are becoming more complex multi-functional teams become responsible for maintenance.At the beginning of the third generation, maintenance organizations began embracing technology to provide efficiencies in maintenance management. A strong push was made to transition from reactive maintenance to proactive maintenance. At the forefront of this push is condition-based maintenance."

Jan 1, 2004

By Y. Faitakis

In the mining industry, maintenance is a key priority and a major expense. As mining equipment is large in scale, high in cost, and difficult to tow, it is key to maintain equipment on a timely basis. Breakdown in -40°C or away from a maintenance station can cause great costs in repair as well as lost production. It has often been quoted that about 5% of the North American production is lost every year due to unscheduled downtime. About one-third of the downtime is attributable to equipment failures. From this fact alone, it is evident that proper equipment maintenance can add tremendous value to the bottom line. As organizations and equipment become more sophisticated, maintenance expectations begin to evolve. This evolution can be traced through three generations: The first generation (1940?1950): A ?fix it when it broke? attitude prevailed during that time, mostly because the industry was not highly automated. The second generation (1950?1980): Automation and mechanization of the industry increased. The industry now was dependent on machines performing the majority of the work. Preventive maintenance (overhauls at fixed intervals) appeared as the first maintenance practice. Maintenance costs started to rise rapidly. The third generation (1980?): Assets become more complex. Failure modes are better understood and computerized maintenance methods are becoming mainstream. Condition-based maintenance (CBM) starts to gain ground as a cost-effective alternative, replacing the fixed interval overhauls. As corporations amalgamate and market places are becoming more complex, multi-functional teams become responsible for maintenance. At the beginning of the third generation, maintenance organizations began embracing technology to provide efficiencies in maintenance management. A strong push was made to transition from reactive maintenance to proactive maintenance. At the forefront of this push is condition-based maintenance.

Jan 1, 2004

By G. H. Babcock, D. A. Knight, V. G. Medina

"Production commenced at the Golden Sunlight Mine in 1983 and at Kidston Gold Mine in 1985. These projects were both constructed under the management of the Placer Dome Inc. (Technical Services) group of Vancouver, B.C.Golden Sunlight uses a conventional rod mill/ball mill grinding circuit while Kidston uses a SAG /ball mill, and later on, SABC circuit. Since the hardness of the ore and the fineness of the primary grind in both mines are about the same, a meaningful cost comparison can be made. The comparison is made on the basis of capital and operating costs.The result of this study indicates that a significant capital cost savings can be achieved in favour of the SAG /ball mill circuit when the ore is amenable to semi-autogenous grinding. With a good maintenance program, the operating cost for the SAG /ball mill circuit could also be lower that the conventional rod mill/ball mill circuit.HISTORYGolden Sunlight MineGolden Sunlight is a 5 530 t/d gold mine located near Whitehall, a small town 60 km east of Butte, Montana. Originally optioned by PDI U.S. in 1958, the development of the property waited until 1981 when economic conditions became favorable for the project to proceed.Semiautogenous grinding tests were conducted during the final stages of the feasibility study. The hard near surface ore was not quite amenable to semi-autogenous grinding. The best result produced from a series of tests using a 1.83 m diameter mill was a semiautogenous work index of 39. This is substantially higher than the 22 Bond work index of the sample used in the testwork. A conventional SAG/ball mill circuit for this ore will be extremely inefficient, and for this reason, this circuit was rejected in favour of a conventional rod mill/ball mill circuit."

Jan 1, 1991

By A. F. Banks

"Potash processing has much in common in terms of unit operations and plant operating strategy with other mineral processing plants. As it is a rather large topic the processes will be broad brushed to give you some background and then I will go into a little detail on the things we do in the Cominco plant that may be of interest to the group as a whole. In particular the centrallized computer control system and associated instrumentation and the operator training programs will be covered as well as the mill fire, something that could happen in any plant. THE ORE AND PRODUCTSThere are differences in potash ores as you would expect. It is my intention to deal with the ores processed in the Saskatoon area. These are mined from the beds in the Patience Lake Member and have a mineralogical description as follows:Sylvite (Potassium Chloride) 40%Halite (Sodium Chloride) 55%Insolubles (Slimes) 5%A number of products are made from this ore. It is characteristic of a potash plant that you put as much effort into grading and converting the sylvite to meet market requirements as you do in recovering it."

Jan 1, 1976

By Norman O. Lotter, André R. Laplante

"The pursuit of concentrator surveying for purposes of metal accounting or process optimization has not yet connected with the well-published realm of geostatistics. The reality of lognormality in time has seldom been discussed. One publication by Krige, 1962, examined such effects for a gold concentrator in South Africa, towards an information system that would provide feedback to the mining and surveying teams on grade control of ore mined.During present studies which are designing and testing a new survey model, called statistical benchmark surveying, it was found that the distributions of feed, concentrate and tailings bear significant residual signs of the parent lognormality in space. The multiple hosting of paymetals in different mineral species complicates the understanding of these distributions. These features have to be recognized and treated in order to perform appropriate quality control on the diagnostic sampling performed in the pursuit of statistical benchmark surveying.It is shown in this paper that the above two features can actually be used to advantage in the diagnosis of continuous periods of operations data ahead of such surveying, including the estimation of recoverable paymetals in flotation tailings from a graphical method.INTRODUCTIONAssessment of Concentrator PerformanceMilling and flotation, sometimes accompanied by gravity separation, are well-established unit processes, which have traditionally been used to treat ore that has been mined. This is because these processes liberate, then separate, the valuable minerals, which contain paymetals, from host gangue. This is often done by a combination of crushing and grinding processes, or autogenous grinding, to liberate the paymetal minerals, followed by gravity separation and/or flotation, to separate these valuable minerals into a concentrate, or several concentrates. These concentrate(s) have a lower bulk than the parent ore from which they are derived. Further, they contain a high percentage of the valuable minerals. Accordingly, they are more economically treated in subsequent beneficiation processes than the ore from which they were produced."

Jan 1, 2005

By B. V. Knelson

"GENTLEMEN:This paper will deal with centrifugal separation - theory and practical, and since the Knelson Concentrator is the only centrifugal concentrator with a properly fluidized bed, this paper will cover the Knelson Concentrator and its technical and structural advances over the last five years. As I am the person with the most experience in this line, I guess I am some kind of an expert; what kind I’m not sure, but some kind.This type of concentrator truly was developed because I’m lazy and I constantly look for easier ways to do things. My experience in the mining industry was very limited but I did realize in looking at placer operations, which is the application where I spring from, that it was tremendously labour intensive and my first reaction that ""my god, there must be some method or way-of handling product in a more efficient (and you can read that as being able to quickly recover very fine particle gold) way than was being shown at that time"". So, the Knelson Concentrator was born - about 6 or 7 years later. Our first attempt was a cone with about the same degree of slope as our present machine and since we had no knowledge of vibration dampening and centrifugal forces at that point, it was just an idea that this should work.Our first run was one of twenty minute duration. We did make that first machine variable speed by a mechanical belt system and we found that at about 240 rpms we were virtually shaking the gravel plant apart that we were attached to. So the first run was twenty minutes and back to the drawing board. However, that first run produced a concentrate so superior to anything we had seen previously, that we knew without any question, we were definately and accurately on the right track."

Jan 1, 1985

By G. A. Kosick, C. A. Harris

"Metallurgy at the Polaris Mine is approaching an impasse, with lead and zinc concentrate grades and recoveries approaching their theoretical maximums. In an effort to increase productivity, plant throughput and operating material costs became a major focus of milling personnel.one method of increasing plant throughput was to minimize flotation circuit upsets by; standardizing operating strategy, decreasing control action response time of operators, increasing training of operators, and providing a more available decision support system for operators.To achieve these goals, Polaris personnel decided to utilize expert system technology to develop a real-time process controller for the flotation circuit which would be capable of justifying its actions to operating personnel.This paper describes the procedures followed in constructing the first process controller in the mineral industry which is based on the principles of Artificial Intelligence.IntroductionThe Polaris Concentrator was constructed in 1980 on a barge in Trois Rivieres, Quebec and towed to its present location on Little Cornwallis Island, North West Territories, about 1450 kilometers from the North Pole. The plant presently treats about 2,800 MTPD of new feed with average feed grades of 3% Pb, 13% Zn and 5% Fe. Current production averages 36,000 tonnes of lead concentrate and 220,000 tonnes of zinc concentrate annually.In an effort to increase the efficiency of the concentrator, the decision was made to implement an innovative control system on the flotation circuit. This system would embody and utilize heuristics ""rules-of-thumb"" gained from operators to make on-line process decisions. It would also justify these decisions on a demand basis."

Jan 1, 1988