Search Documents

By A. J. Antony Chettupuzha

Electronic Product and Process Management [EPPM] systems provide the capability to establish and map information flow between different parties in a construction project as well as model project processes. Much of the information relating to processes and their structure, the actors that operate them, and the data associated with each instance of a process is encapsulated within workflows. The wealth of information contained in an EPPM system can be exploited to extract knowledge that can provide significant cost benefits to construction companies. Workflows provide an ideal medium for the capture of knowledge over the course of a project lifecycle. We demonstrate how this knowledge may then be used to analyze workflows and determine metrics that establish the suitability of workflows to construction processes. We present a conceptual approach to measure the performance of a workflow, its constituent components and evolution, which may be used to lay the foundation for establishing paragon workflows suited to classes of construction activities.

Aug 1, 2013

The problem of thin and very thin coal seam extraction in a long perspective of Ukraine?s fuel and energy industry development was determined. Technical and economic benefits of coal seams selective mining technique including beneficial environmental impact were substantiated. The scientific and practical aspects of development of borehole underground coal gasification (BUCG) technology are considered. The technological scheme of underground gas generators is offered on the basis of the authors? criteria of fitness and adaptability to the mine and geological conditions. These charts foresee the preparation of gas generators from earth surface and directly from the present mine working by inclined horizontal boreholes. Basic research is directed at abandoned supplies extraction in coal mines. Concepts of technological decisions and technical implementation of the underground part of the gasification system are worked out with analytical models, with subsequent test verification on special options and a mine experimental gas generator. Forming the technological scheme of gasification is founded on the basis of tying up spatial and sentinel factosr of coal seam gasification taking into account sufficient impermeability of the system a «gas generator ? rock massif» and to dirigibility by thermochemical processes that flow in a rock massif. The offered solutions contain the possibility of creation of the power and chemical enterprises of gasification, taking into account the complex use of BUCG products in the ecologically reserved technological cycle. Gas generator efficiency is evaluated from an economic standpoint.

Aug 1, 2013

By F. O. Verret, A. McKen, G. Chiasson

Several grindability tests were developed over the years to design grinding circuits or optimize existing operations. Each test has its own strengths and weaknesses and it is imperative to select the proper test procedure(s) to meet project deliverables and minimize the risk of a project. Pilot plant testing of large bulk samples historically constituted the traditional approach for AG or SAG design, but was gradually replaced by small-scale tests. Nowadays, conducting grindability tests requiring only a few kilos of material on several samples is a more typical approach to grinding mill design. This paper summarises the requirements and deliverables of various bench-scale test procedures, their strengths and weaknesses, and cases where AG/SAG pilot testing should still be performed.

Jan 1, 2012

A series of small scale tests have been conducted to evaluate the effect of micro-fracture development, imposed by blasting, on the material properties of the rock as well as its resistance to crushing and grinding. The uniaxial compressive strength, tensile strength, Poisson?s ratio, P-wave, Swave velocity, point load test index, crushing and grinding work indices were evaluated for samples without any blasting load and for samples which had received a variety of blast loads ranging from a single impact with low strength detonating cord, to combination of impacts at different times and significant impacts with powder factors close to those used in practical blasts. It was shown that the rock mechanics parameters change even at low impacts, suggesting easier crushing of the rock. Damage values appear to be affected by timing as stress wave superposition affects the damage process. Fragmentation is achieved at higher impact levels while work index modification of the fragments is also observed when high powder factors are used, suggesting improvements in grinding.

May 1, 2003

The Boleo project is located in Mexico close to the town of Santa Rosalia on the Baja Peninsula. The Boleo deposit contains copper, cobalt, zinc and manganese values as oxides with minor sulfides. The Boleo deposit is metallurgically challenging due to: 1) the requirement to recover four separate metals; 2) the presence of high levels of clay in the deposit resulting in difficult solid-liquid separations, and; 3) the need to use seawater for the bulk of the processing. Baja Mining, Bateman Engineering and SGS Lakefield Research have collaborated to develop and test a process flowsheet to recover copper, cobalt, zinc and manganese products at Boleo. The key steps in the flowsheet are: ? Feed preparation (scrubbing and ball milling of oversize) in copper raffinate ? Ore leaching using oxidative and reductive leaching ? CCD washing using high rate thickening technology ? Copper SXlEW ? Treatment of a bleed solution for cobalt, zinc and manganese recovery The process for cobalt, zinc and manganese recovery involves iron and aluminum removal followed by cobalt/zinc bulk extraction using CSIRO's DSX solvent extraction system and selective zinc and cobalt stripping. The zinc strip solution is evaporated to produce zinc sulfate monohydrate crystals to market and cobalt is recovered via a further SXlEW process as high purity metal. Manganese is precipitated as manganese carbonate from the DSX raffinate solution. This paper will review the Boleo process flowsheet and provide detailed results from the 2006 pilot plant operation conducted at SGS Lakefield in Canada.

Jan 1, 2007

By A. Fawceit, B. C. Dyer

"The basis of the tomographic velocity imaging technique is briefly described and an application of the method to detect and image a cross-section through a chromite pod is presented. Using the chromite application as an example, the relative costs of tomographic data acquisition and processing are compared with those of diamond drilling to obtain similar resolution. A number of different tomographic survey configurations and the potential role of the method in surface and underground exploration are discussed.IntroductionThe technique of seismic tomography has been most widely applied in oil industry exploration, nuclear waste disposal, civil engineering site investigations and in the assessment of the condition of mass concrete structures. Although model studies had indicated that tomography would be a useful tool in mineral exploration, relatively few applications have been reported.Essentially the method relies on the determination of the speed with which sound travels through a region within a cross-section of the earth or large body. The speed of sound is determined by the physical characteristics of the medium through which it is passing. In geophysics the speed of sound is generally referred to as the seismic velocity. Due to variations in the formations of different rocks the seismic velocity will vary and so can be used to map geological boundaries"

Jan 1, 1994

By M-A. Thibault, C. Gauthierand, J-P. Gagné, J-Y. Carrier, P. Rochette, G. Dufour

"Anodes consumed in the electrolytic process for the production of primary aluminium are considered consumables. They need to be replaced at regular intervals of approximately one month. The so-called anode butts which are removed from the cells contain the metal supports (rods), cast iron thimbles, crust and residual carbon material. Cleaning is required to remove the waste material before the rods are fitted with new anodes. An inspection is required to ascertain if repairs to the rods are necessary. Presently, this inspection is carried out visually. ST AS, in 2004 in collaboration with Alcoa Deschambault, initiated a project to develop an automated inspection system. The objectives were to find a technical solution to perform these functions with a very simple system. Such a system was designed around ""artificial vision"". The inspection system developed uses only one fixed camera and does not require a separate step in the process for the anode rod assembly to perform the inspection. This paper presents the initial steps of the work performed to develop the equipment and software as well as a summary of the results obtained."

Jan 1, 2006

By Gerald A. Crawford

"1880s - Unmasking the Sudbury Basin Falconbridge Ltd. turned 60 in 1988 but its roots go back more than a century to the discovery and development of the mineral resources of the Sudbury Basin. Nickel was first identified in the area in 1856 but sustained exploration awaited the early 1880s and the advance of the CPR westward from Sudbury. Rock was laid bare in the right-of-way and by forest fires and logging. Reddish oxidized outcropping or ""gossan"" were exposed, heralding the presence of nickel as the shape of this astounding geological formation gradually began to emerge. Many great mines of the area were opened up in this period on the south rim of the Basin west of Sudbury. To the east the ore dips below overburden, however, and Falconbridge remained a mere dot on the map until the turn of the century when Thomas Edison detected a magnetic occurrence by dip needle."

Jan 1, 1999

By T. Yalcin

"This paper describes a process that can provide high rates of dewatering and that has the potential of bringing significant savings in tailing disposal costs. It involves a three-stage, closed-circuit operation employing a hydrocyclone, a settling cone and a thickener. The mill tailing, with adjusted pulp density, is first fed to the hydrocyclone. The underflow from the hydrocyclone goes to the settling cone for further dewatering. The overflows from the hydrocyclone and the settling cone are sent to a thickener which, with the addition of a flocculant, gives a clear liquid effluent and a dilute underflow which is recycled back to the hydrocyclone. The underflow of the settling cone is a material with as high as 78% pulp density and is suitable for direct disposal or for use as mine backfill.INTRODUCTIONDewatering is an essential process for the disposal of mill tailings and forms an additional cost item in milling operations. Cost-cutting measures are therefore desirable in this area as in any other stage of milling. One way of achieving this is through increased rate of dewatering which would require smaller dewatering units with correspondingly lower capital and operating costs."

Jan 1, 1987

By A. Y. Senchenko, Y. V. Kulikov

"In recent decades HPGR technology has proven itself in comminution circuits of mining plants. High technical and economic performance, lower specific energy consumption and reliability of HPGR equipment makes it an efficient alternative to conventional circuits using stage crushing and rod/ball milling, as well as to AG/SAG circuits. However, despite all the advantages of this technology the correct selection of key and auxiliary equipment is very important since errors at testing and design stages may lead to discrediting of the whole concept of HPGR application. There is a great variety of possible circuit configurations using HPGR, e.g. with circulation of edge product, with crushing of the whole discharge and circulation of screen oversize, successive two-stage crushing, etc. Each type of minerals will require its own optimal crushing circuit. In this context the testing methodology for selection of an optimal configuration becomes of prime importance. It is common knowledge that the best simulation of material crushing and softening within a HPGR can be obtained only in the course of a large-scale pilot test. The main approaches applied to this kind of testworks are described in this article. Special aspects of HPGR technology design and industrial operation are revealed as well. Some operational issues of HPGR equipment and of circuit as a whole were detected. They are related to regions specifics, plants location, and other factors. Process solutions proposed to deal with these issues are also indicated in the article. INTRODUCTIONDesign and construction of the processing plants involving High Pressure Grinding Rolls (HPGR) technology becomes more and more common in mining as this technology has specific technical and economic advantages against the circuits with autogenous/semiautogenous mills (AG/SAG) and other circuits. The main advantage of the technology is low energy consumption and low operation costs respectively. The presence of microcracks and increased content of fine size fractions in the crushed product contribute to reduction of energy required for further ball grinding. Besides, HPGR technology applies a special wear resistant liner that enables significant reduction of operation costs of grinding media and liner comparing with AG/SAG circuits."

Jan 1, 2016

By H. J. lgner

Hydraulic fills are widely used in the tabular, steeply dipping stopes of the South African gold and platinum mines as an integrated process within a daily cycle of drill and blast. There is therefore only a small time window in which to fill the geotextile bags used as primary fill containment, without the risk of loosing production. Consequently, mines tend to increase the flow rate to the stopes, although this compromises adequate drainage, consolidation and strength development during filling. Recent underground measurements inside the geotextile bag have revealed that at high rates of rise and at 25 degrees dip, the backfill can remobilise within a limited area inside the geotextile bag during filling. This sudden downward surge of backfill exerts, for only a few seconds, additional loading on the geotextile, its supporting mesh and the props. This unstable behaviour poses a serious threat as it can push props out of place, thereby damaging the geotextile bag and causing a mud slide in the stope. To reduce the risk of accidents, the phenomenon of sudden slumping was further investigated for various filling conditions in the laboratory. The results confirmed that the maximum pressures associated with the sudden slumping can be more than five times those experienced during steady-state consolidation. Based on this new insight, the current best practice for hydraulic backfilling was critically reviewed. A practical approach to implementing meaningful standards is presented to ensure safe operations in relation to the consistency of the backfill quality and the appropriate matching of geotextile characteristics with backfill properties.

May 1, 2007

By Sudarshan Martins

The measurement of acoustic signals produced by a tumbling mill has been previously used to determine the operating state of the mill and correlate the variations of the sound intensity with the operating conditions of the mill. Separately, the discrete element model (DEM), a software simulation of the mill, was developed to provide insight into the operation of the mill. Presently, there has not been much work reconciling the DEM simulation of the mill with the acoustic signal. Working from basic principles of linear, time-invariant systems, agreement between an acoustic DEM simulation and the measured signal is sought. First, the impulse response function of the mill is measured. The DEM provides the forces applied to the mill shell as a function of time. A convolution of these simulated shell forces and the transfer function gives the simulated acoustic signal. This signal is compared to the measured acoustic signal, both in the time domain and the frequency domain. Finally, a discussion of the results is given.

Jan 1, 2012

By N. Romani, R. Provost

"Commissioning of a circulating dry scrubber plant was recently completed at an existing facility, in order to treat the sulphur dioxide off-gas emitted from rotary kilns. Proper planning of the different commissioning stages and staffing an integrated team are the most important factors required for a successful plant start-up. A strong operational readiness plan must be in place as early as the start of construction in order to ensure a smooth transition from commissioning to operations. Plant performance can meet or exceed performance criteria within the required timeframe if the proper group dynamic and good communication is established between construction, commissioning and operations teams.INTRODUCTIONCommissioning of a circulating dry scrubber (CDS) plant was recently completed at an existing facility in Quebec, Canada. The CDS plant treats the sulphur dioxide off-gas emitted from rotary kilns in order to meet increasingly stringent environmental requirements. This installation enables the existing facility to reduce their sulphur emissions by over 90%.The CDS ProcessA general overview of the CDS process is presented in Figure 1 below. The combined, de-dusted off-gas from multiple kilns is sent to the CDS, which acts as an entrained fluid bed, where the gas is contacted with a water mist, re-circulated solids and hydrated lime. The SO2 from the gas stream and the available calcium hydroxide (Ca(OH)2) from the hydrated lime dissolve in the water and react to ultimately form calcium sulphites and gypsum. The solid residue (referred to as CDS residue), is the primary byproductof the process.Fresh hydrated lime and CDS residue is captured by the dust collection system and is re-circulated to the CDS via a fluidised transport system. Clean off-gas passes through the dust-collection system and is then sent to the atmosphere by a single exhaust fan.The CDS residue purged from the system is combined with the dust collected from the kiln offgas system and this mixture is wetted in the already exiting agglomeration system, to minimize dust generation during handling, and then sent to disposal."

Jan 1, 2016

By Peter D. Cunningham

At Vale Inco in Sudbury, underground mobile equipment production and maintenance data is presently collected manually from paper slips. This paper reviews a pilot project that developed a system to electronically collect that data. The benefits and improvements in data accuracy, timeliness and reduction in collection effort, will be discussed. Technological issues that arose from the use of WiFi, RFID (Radio Frequency Identification) and the IREDES mine data equipment standard are also discussed.

Oct 1, 2009

By Michel Ruel, Ali Soltanzadeh, Benjamin Légaré

High fidelity commercial process simulation packages can be used at different stages of a greenfield project, from initial plant design to operator training in the later stages. However, there are several factors that make the software less attractive for small and medium size brownfield projects, such as the licensing cost and the fact-finding manpower required for model design and simulator maintenance. In this paper a different approach is described. The knowledge gathered from operating personnel was used to implement higher level models based on plant data, operating heuristics, and experience rather than detailed component-level models. The computing platform used was a low-cost, well-established, control system vendor-independent software. Throughout this paper we demonstrate the success of implementing this model-based approach using two industrial examples. The first example is a simulation of the carbon monoxide (CO) distribution system at a metallurgical complex. The purpose of this simulator was to test new control strategies and PLC programs prior to implementation. CO being a toxic combustible gas, validation of the suggested control system changes was necessary for plant safety. Simulation of specific operating conditions helped alleviate concerns and improved plant-wide acceptability of the new operating philosophy. The second example is a boiler simulator at a petrochemical plant. The operator training simulator (OTS) was designed as a platform for experienced operators to practice handling rare or abnormal conditions. A customized medium-fidelity model was developed for this targeted application where the cost of a full scale high-fidelity model could not be justified.

Jan 1, 2016

By Jan Butra

Longstanding mining of copper deposits in the Legnica-Glogow Mining Basin, Poland has accumulated broad experience concerning the impact of geological and mining conditions on seismic and rockburst hazard. Methods of rockburst prevention for deep copper mines have been developed based on gathered data. Methods of rockburst hazard evaluation and rockburst control constitute a set of rockburst prevention measures. Due to their nature and location within the production process, prevention methods can be passive or active. Active methods of rockburst prevention consist of the liquidation of stresses in the areas where they are concentrated through controlled generation of rock-mass tremors and rockburst by blasting works (group extraction blasting, release blasting in the rock mass and pillars able to accumulate the stress, as well as in the roof and floor). Group blasting works as a basic method are very effective in copper mine conditions. Provocation of dynamic events makes it possible to control the timing of their occurrence. In Polish copper mines, all blasting works are made during the absence of miners in the mining fields. Daily distribution of both the number of recorded strong seismic events and volume of energy released, confirm the advisability of using this kind of rockburst hazard prevention. The rockburst hazard prevention methods developed over 40 years of copper deposit extraction are economically reasonable and offer sufficient effectiveness under high rockburst hazard conditions.

Aug 1, 2013

By A. J. Antony Chettupuzha

During a construction project, it is important to ensure that accurate and pertinent knowledge is delivered on time to appropriate personnel. The criticality of documents exchanged or referred to by various parties, evolves over the course of the project lifecycle. Determining the criticality of documents at different stages of the project can aid companies with managing the flow of information in an organized manner, while providing for the detection of potentially disruptive, erroneous material that could result in delays and costs. Therefore, it is crucial to determine documents which have the potential to disrupt a process (by virtue of being incorrect versions etc.) so that they may be isolated or prevented from entering or interfering with the active flow of information in a project, while also ensuring standard revisions of documents are recognized and accessed accordingly. Electronic Product and Process Management [EPPM] systems provide the capability to establish and map information flow between different parties in a construction project. Analyzing an EPPM system may yield information about the criticality of certain documents within an activity, as well as isolate characteristics peculiar to documents which can assist in risk mitigation. We propose methodology that identifies such critical documents.

Aug 1, 2013

By E. Lovera

ABSTRACT: The current study analyzes the feasibility of an odd operation: to obtain, using a properly tailored drilling and blasting scheme, blocks suitable for the production of dimension stone from tunnel driving. Clearly, a compromise must be found between the rate of progression and the achievement of workable blocks. As a case study, a civil work under consideration in northern Italy was examined. The work was planned to cross a conglomerate that has traditionally been locally exploited for the production of highly prized paving and lining stones with excellent strength and aesthetic features. Natural exposures and mined-out quarries were available for tests. The relevant rock data are given, blast designs are shown (within the limitations of contour accuracy), and the test program is described.

Jan 1, 2011

By Guoxiang Chi

This paper consists of two parts: the first part describes the principles and functionality of the BsnMod program, and the second part presents preliminary application of this program to paleo-fluid flow modeling in the Anticosti Basin. The BsnMod program simulates fluid flow and heat transfer during the evolution of sedimentary basins through numerical solution (finite difference method) of three partial differential equations, which describe sediment compaction, fluid continuity, and heat conservation. It can be used to estimate the evolution of fluid overpressure, flow rate, and temperature during the basin history. The program was written in C++, works under Windows environments, and has a user interface allowing inputs in dialogues and outputs in both tabular and graphic forms. The program was applied to the Lower Paleozoic Anticosti Basin in eastern Canada. The basin history consists of a passive margin stage and a foreland basin stage. Preliminary simulation results indicate that no significant fluid overpressures were developed in the passive margin stage and during the early period of the foreland basin stage, but strong overpressures were developed within the foreland basin succession during the middle and late periods of the foreland basin stage. Fluid flow rates were generally slow, and thermal profiles were not significantly disturbed by fluid movement throughout the basin history. Potential source rocks of hydrocarbons were found in the foreland basin succession. The strong overpressures in the foreland basin succession could have been a major driving force for hydrocarbon migration from the source rocks to the underlying potential reservoir rocks.

May 1, 2001

By Chin J. Chang

Powder metallurgy (P/M) technique is known for its capability of producing near-net-shape parts. Its specific characteristics have resulted in low cost and eliminated of many secondary machining. However, more and more P/M parts do require additional operations to fulfil their complex geometric features and surface roughness. Many of the machining factors that influence the machinability of cast and wrought steel parts, such as cutting speed, feedrate, coolant, tool geometry and shape, are also considered in the machining of P/M components. The special feature in P/M structure is the porosity that can decrease the machinability and shorten the tool life. Different variables have been considered in the machinability of P/M materials. Densities and the free machining additive manganese sulphide (MnS), are the two main factors of material composition, which dominate the P/M machining performance. Machining process is the main method that generates the desired working surface of machining components. This paper will discuss the metallurgical structure of the powder metallurgy components, their physical properties and possible issues when encountering machining operation. Turning operation has been tested in this investigation to show the relationship between the cutting speed, federate, cutting forces and chip formation. This investigation also discusses how the free machining additive, manganese sulphide, affects the P/M structure and machinability in order to understand how the metallurgical structure can affect the machining operation and, how to obtain the optimised surface results.

May 1, 2001