Search Documents

By Jayesh B. Patel, Zhongyun Fan, Hu-Tian Li

"Melt conditioned direct-chill (MC-DC) casting is a novel technology which combines vertical direct-chill (DC) casting with a high shear device directly immersed in the sump for in situ microstructural control. In this paper, the solidification mechanism of DC casting under varying conditions is discussed. The temperature profiles in the sump were measured under the steady state casting conditions by using sacrificing thermocouples. Detailed comparisons of the derived thermal condition are made. The individual role of grain refiner additions, natural thermosolutal convection and forced convection in the sump and the interplay of these factors in determining the solidification structures of DC cast billets are discussed. The MC-DC casting technology can be used to control microstructural constituents and casting defects in DC cast billets/ingots by in situ manipulating of the thermal and fluid flow conditions.INTRODUCTION Direct-chill (DC) casting of aluminium, has been the essential commercial process for producing feedstock suitable for subsequent processing, such as extrusion, rolling or forging. Fine and equiaxed grain structures in the as-cast billets/ingots are required to enable a fine and uniform distribution of second phase particles and microporosity. This leads to higher productivity, more cost-effective homogenisation and more efficient downstream thermomechanical processing. The addition of chemical inoculants has been the standard industrial operation prior to casting for grain refinement of Al alloys. However, it has been established that less than 1% of the grain refiner particles added actually act as heterogeneous nuclei to refine the grain structures, showing a very low grain refining efficiency (Greer, Bunn, Tronche, Evans, & Bristow, 2000). Moreover, the remaining particles from the grain refiner addition in the final casting may cause surface defects during downstream processing. A major issue of the metallurgical quality of large sized ingots/billets is the non-uniformity of microstructures even with chemical grain refiner additions. This is due to the fact that the grain structure formed in the different zones of the billet depends on the local chemical composition and local cooling rate. The local cooling rate can vary from 0.4~1 K/s at the centre of the billet to around 10–20 K/s at its surface zone (Nadella, Eskin, Du, & Katgerman, 2008). The large thermal gradient along radial direction between billet surface and interior of the melt during conventional DC casting induces thermal stress and cold cracking even with grain refiner addition. Therefore the control of casting defects, such as macrosegregation, porosity, cold/hot cracking and distortion of the billets/slabs, etc., is still challenging in industry, causing high scrap rate of DC cast ingots/billets even with grain refiner addition."

Jan 1, 2018

By D. Royston

In SAG mills fed with a variety of ore types, hard packing between the shell lifters can come and go depending on rock type and rock size distribution and the presence of a binder. Packing can appear in all sizes of SAG mills, and can be tenacious. High ball impact forces (depending on ball size) in larger mills may compact and encourage packing. Packing can have a negative impact on milling performance and a change in shell liner design may be required to remove it. However shell liner design changes need to be managed with care to ensure liner reliability. In smaller mills control of packing can extend shell plate wear-life and may help to maintain milling performance in fixed-speed mills through the liner wear-cycle.

Jan 1, 2012

By Y. Obara, A. Sato

"Limestone is one of the most important mineral resources, and in Japan it is only one mineral which can be fully supplied by the domestic product. Generally limestone mines in Japan located at mountainous regions, and the combination between bench-cut method and the carry-out system using vertical shaft is widely used in the domestic mines. During mining operations, the occurrence of the blockage in the vertical shafts is very serious problem. Once the blockage in the shafts is occurred, a lot of works and dangerous procedures are necessary to solve the problems. It is thought that blockage is influenced by the cohesion and friction coefficient due to clay minerals thrown into the vertical shafts, however, the quantitative and precise reason is not revealed yet.In this study, the process of blockage occurrence was simulated by 2-Dimensional Discrete Element Method (DEM). In the 2D-DEM analysis, discontinuous circular particles are generated, and the individual movement of each particle is calculated by forward difference method. In the analysis, several typical ore distributions are applied, and the DEM analysis was conducted under the various combinations of cohesion and friction coefficient. From analytical results, it was found that the friction coefficient strongly influences to the occurrence of blockage and there were a threshold values which blockage does not occur. Several kinds of shaft shape were also simulated towards different ore size distributions, and those influences to the blockage occurrence were also discussed."

Jan 1, 2015

By S. N. Dixon

"Maximizing the value of each tonne of processed ore is the goal for all operations. Cyanidation processing of gold-copper ores has been challenging since its first use in 1889. The current practice treats a bleed or the total flow of mill solution to recover copper as copper sulfide (by sulfidization, acidification, recycling, and thickening), or to recover the cyanide (by acidification-volatilizationneutralization). The process presented uses the adsorption of copper cyanide by carbon and the selective elution of copper from carbon to concentrate copper into a smaller stream. Copper contained in the smaller stream is precipitated as copper cyanide.RÉSUMÉ Toutes les exploitations ont pour objectif commun d’optimiser la valeur de chaque tonne de minerai traité. Depuis sa première utilisation en 1889, la méthode de traitement par cyanuration des minerais aurifère et cuprifère s’est révélée complexe. La pratique actuelle traite la saignée ou le débit total d’une solution de traitement du concentrateur pour récupérer le cuivre sous la forme de sulfure de cuivre (par sulfuration, acidification, recyclage et épaississement), ou pour récupérer le cyanure (par acidification, volatilisation et neutralisation). Le procédé présenté dans cet article utilise l’adsorption sur charbon actif de la solution de cyanure de cuivre et l’élution sélective du cuivre depuis le charbon pour concentrer le cuivre en un plus petit jet. Le cuivre contenu dans ce plus petit jet est précipité sous forme de cyanure de cuivre."

Jan 1, 2017

By J. F. Nie

Mechanical properties of precipitation hardenable magnesium alloys depend critically on the chemistry, structure, morphology, orientation and distribution of strengthening precipitates. It is therefore important to gain an improved understanding of these information and their correlations with mechanical properties. Our recent studies indicate that additions of 1-2 wt% of Zn to a Mg-6wt%Gd alloy result in a substantial enhancement in precipitation hardening and in creep resistance. If the strength and creep resistance of the resulting ternary alloy are to be further enhanced for commercial applications, then a detailed characterisation of the strengthening precipitates in these alloys is required. In the present study, the precipitates formed in a Mg-6Gd-1Zn-0.6Zr (wt%) alloy, peaked aged at 250°C, have been characterised in detail using transmission electron microscopy and 3-dimensional atom probe field-ion microscopy. It is found the peak-aged microstructure contains a dense and uniform distribution of precipitate plates that form on the basal plane of the matrix phase and are typically less than 1 nm in thickness. Detailed analyses of the structure and composition of these basal precipitate plates will be presented and discussed in the context of previous work on other Mg-RE¬Zn alloys of similar compositions.

Jan 1, 2006

By B. Grinbaum

The solvent extraction of Cu from acidic leach solutions is carried out using oxime extractants. The mechanism can be described as liquid ion exchange, where a labile H+ in the oxime replaces Cu++ ion from the pregnant leach solution. The process is reversible and, at high acidity, the copper is stripped back to the aqueous phase. As the extraction proceeds, the acidity of the aqueous phase increases and the equilibrium may shift against the extraction reaction. This phenomenon may become significant in leach solutions with high copper concentration, where large amounts of acid are transferred from the solvent into the aqueous phase. An efficient way to increase the recovery of copper consists of splitting the extraction into two circuits, and either neutralizing with lime or extracting the excess acid of the intermediate raffinate. In the second case, the acid can extracted using a solvent, which can be stripped with a base, e.g., NaOH or ammonia. A third option is direct neutralization with soluble basic salt, e.g., Na2CO3, within a single extraction battery. The choice of the preferred process depends on the specific process demands and on the relative availability and price of the raw materials and by-products price.

Jan 1, 2007

By U. Martin

Advanced copper materials for conducting applications require an optimal combination of high mechanical strength at ambient and moderately elevated temperatures together with superior electrical and thermal conductivity. Mechanical alloying under repeated cooling of the milling vials in liquid nitrogen has been applied to produce ultra-fine grained (UFG) oxide dispersion strengthened (ODS) copper with a high yield strength at ambient temperature. In the present study ODS copper was manufactured by mechanical alloying of copper powder and 3% by volume of incoherent oxide dispersoids. During the high-energy milling a homogeneous distribution of fine dispersoid particles (diameter nearly 100 nm) can be achieved in the powder. Samples with a density of more then 97% of theoretical value were produced by uniaxial hot pressing under 650 MPa at 600°C for 20 minutes. The high yield strength at ambient temperature can be described by a linear superposition of the Orowan stress for particle hardening and of ultra-fine grain strengthening according to the Hall-Petch mechanism. Simultaneously, a best value of 75% IACS could be obtained for the electrical conductivity. The creep behaviour of ODS copper in the temperature range from 500°C to 700°C is described within the frame of diffusional creep deformation.

Jan 1, 2007

By G. Viramontes-Gamboa

Approximately 70% of world copper reserves consist of the mineral chalcopyrite, and much international effort has focused on its study. Ultimate objectives include the development of environmentally friendly alternatives to smelting, and technologies to treat low-grade ores, for which concentration and smelting are economically unviable. Unfortunately, chalcopyrite leaching is inefficient in H2S04-Fe2(S04)3-FeS04 solutions, which is considered to be the most desirable oxidizing medium for leaching of copper sulfides, since the chemistry is well known, corrosion of industrial equipment is negligible, subsequent copper recovery by SXlEW is well established, and environmental impact is minimal. The main reason for this inefficiency is the self-passivation of chalcopyrite. We have devoted considerable effort in the understanding of this phenomenon, and have developed a predictive electrochemical methodology capable of establishing a priori the precise range of potentials within which chalcopyrite leaches and where it is passivated. Since potential control is a critical parameter in chalcopyrite leaching, this experimental methodology can be very useful for establishing the best conditions to leach chalcopyrite. In this paper, the scientific foundations of this predictive experimental technique are presented, and its practical application is demonstrated by comparing its predictions with leaching experiments from the literature.

Jan 1, 2007

Accountability for profit realized or lost, and responsibility for continued safe operation are the main impetus behind operator training. Efficiency in operation enables production at lower unit costs. An inefficient operation eats profitability of the operation, creating short term losses, and also affecting longer term viability particularly when commodity prices fluctuate and competition erodes market share. Safe operation and efficient operation are ultimately conjoined entities which may not be able to be sustained without dual effort. Training is a very valuable tool to engage operations in adopting more efficient and safe practices. Training requires time, facilities and trainers. One novel way of minimizing both the trainers and the facilities is through the use of Computer Based systems. Included amongst this are Computer based equipment simulators, following an identical philosophy as flight simulators used for pilot orientation and training for different aircraft types.

Feb 1, 2008

By Ann Lamontagne

Le parc à résidus de l?ancienne mine Dunraine contient des résidus générateurs de drainage minier acide. Le concept proposé pour la restauration du site est d?utiliser le fort potentiel alcalin des boues rouges, résidus d?aluminerie, afin de neutraliser les résidus miniers. En appliquant une certaine quantité de boues rouges à la surface du parc, on provoquera une neutralisation de l?acidité. De plus, les alcalis contenus dans les boues rouges vont provoquer la précipitation de minéraux stables (sulfates tel la jarosite). La précipitation de ces minéraux provoquera la formation d?une couche indurée qui rendra difficile la circulation de l?oxygène et de l?eau. Bien que ce concept ait été vérifié en laboratoire, ce sont là des hypothèses qui restent à vérifier dans des conditions réelles d?exposition. Les principales questions soulevées par l?utilisation des boues rouges, mis à part le contexte géochimique, est le contexte technico-économique. En effet, le transport de quantité importante d?un matériel argileux humide présente un défi économique important. Outre le défi économique, la manipulation et l?épandage de ce produit sur des parcs à résidus constituent également un défi important. Cet article présente les conclusions d?une étude technique sur le transport, la manutention et l?épandage de boues rouges sur un parc à résidus situés en Abitibi : le site de Dunraine.

Nov 1, 2002

By Mario A. Morin

Over the years, several sources have stressed the need to better integrate the underground mine design and planning processes. The belief is that with better integration, better designs and plans will result - designs that are ?optimized?. Some researchers have focused their efforts on data integration, others have looked at closing the loop between production control & monitoring with mine planning & scheduling. In spite of all these efforts, fully integrated applications combining geological modeling, stope design and geomechanics, mine planning and scheduling, rock extraction and material handling system design, mine support systems, economic analysis with production control do not yet exist for the underground hard rock mining industry. There are several likely explanations - some economic, some technical. It is certain that the design and planning processes are interrelated and interdependent and thus are extremely complex to describe and understand. The mining engineer has an appreciation of the complexities involved - but how does he convey this knowledge to a programming team responsible for developing an integrated design & planning system. This paper will focus on software engineering methods, and other possible approaches, to describe and manage the complexities inherent in the underground mine design and planning process and the development of an integrated computerized system.

May 1, 2001

By K. Bowes, M. D. Maley, R. J. Ring

The Honeymoon Uranium Project is an acid In-Situ Recovery (ISR) mine in South Australia. It was previously operated for approximately 18 months before being placed on care and maintenance in 2014, it was then acquired by Boss Resources in 2015. Boss has been performing a number of studies to plan for reopening of the mine, including a successful field leach trial (FLT) in 2017. The current configuration for uranium precipitation at Honeymoon is a batch process. Whilst this achieves effective uranium recovery, the precipitates produced are often very fine, with poor settling and solid/liquid separation characteristics. Continuous precipitation, involving recycling of solids, has reportedly been successfully utilised in other operations to increase the particle size and density of the product, leading to solids that can be more readily dewatered, dried and drummed, with less fines and dust generation. However, no operational data are available from such operations.

Jan 1, 2020

By A. J. Russell

"This paper investigates why it is critical for a mine to accurately determine thermal rock properties and virgin rock temperatures. Theoretical simulations of deep mining production zones have demonstrated that thermal conductivity (k), virgin rock temperatures and specific heat (cp) significantly impact rock heat predictions which can be the dominant component of a mine’s heat load. Natural variability in these factors showed that realistic errors can have a significant effect on mine heat loads. This can ultimately affect miner safety and introduces risk to the viability and sustainability of a project. INTRODUCTION Accurate heat load determinations are critical to ensure that underground working conditions are maintained within legislated and mine specific parameters to safeguard the safety and productivity of employees. Underpredicting mine heat loads will result in hot underground conditions, which risk the health and safety of employees, reduce the productivity of employees or stop production if legislated temperatures in working areas are exceeded. Overestimating mine heat loads will result in increased capital and operating costs reducing the viability of the project. Over- or under- predicting the heat load for a project will increase the project risk. Heat sources in a mine can broadly be broken into two categories. These two categories are defined by Hemp and Rawlins (2014) as natural and artificial heat sources. Those sources which depend on the size, location and depth of the mining areas are defined as natural heat sources, whereas those heat sources which are a result of the actual mining activities are defined as artificial heat sources. Autocompression, or the conversion of potential energy, to enthalpy is an important consideration when determining the air temperature in the mine and its interaction with natural and artificial heat sources. It is documented by Jones (1985) and Hemp and Rawlins (2014), that the heat flow from rock in deep mines can dominate other heat sources; information from BBE’s archives show that this is between 40% and 60% of the total heat load. They also point out the importance of accurately measuring both the thermal rock properties and virgin rock temperatures (VRTs) for determining and planning the ventilation and refrigeration requirements for a mine. Both of these texts cite multiple methods for calculating the heat-flux and ultimately the heat load for the different working areas in a mine. All of these methods demonstrate that the heat flux and heat load will increase proportionally with increased thermal conductivity (k), specific heat (cp) of the rock or mineral, and VRT depending the area of the mine or mining method."

Jan 1, 2019

By M. E. Hurst

Introduction Between 1903 and 1905, W. Mclnnis, of the Geological Survey of Canada, made a micrometer traverse of the Kawinogans (Crow) river from Kapkichegimaga lake to its junction with the Otoskwin river. He reported that a belt of Keewatin rocks, 1 to 4 miles wide, was exposed along the course of the river for 17 miles east of Kapkichegimaga lake. Prospectors and exploration companies paid little attention to the mineral possibilities of this belt until the summer of 1928 when, with the adoption of airplane transportation, the area became readily accessible. Within a short time widespread interest was aroused by the announcement of attractive finds, and a mild rush followed. During the winter months, hundreds of claims were staked on either side of Crow river for 12 miles east of Pickle lake. In the summer of 1929, much of this ground was systematically explored and a considerable amount of development work was done on the known deposits.

Jan 1, 1930

By L. J. Surges, C. Bazin, D. Hodouin

"A kinetic model was developed for the conditioning and flotation processes of an industrial lead concentrate dezincing circuit. The models were incorporated into a flowsheet simulator. Simulation results demonstrate the advantages of split conditioning of coarse and fine particles and the potential of this approach for the production of the heuristics required for the development of intelligent control strategies.The conditioning model relates the proportions of activated and hydrophobic surfaces and residual reagent concentrations to activator and collector reagent flowrates. The model accounts for the solids and water flowrates, and for the solids grade and size distribution. The flotation model uses the predicted proportion of hydrophobic mineral surface, the aeration rate and the froth depth to estimate cell, bank and circuit performances. IntroductionFlotation has been the object of modelling and simulation studies for more than two decades. The process is usually modelled as a kinetic one in which the particle flotation rate constants are key parameters. Rate constants are related to the operating variables (pH, reagent flowrates, aeration rate, etc), however these relationships are seldom established in the literature.In spite of the large amount of literature on flotation modelling and simulation, few papers deal with the interaction between flotation rate constants and operating variables. This important gap, which was identified in the early seventies by Woodburn (l970), still exists. One of the first attempts to include operating conditions in a flotation simulator was made by King (l973), who explicitly introduced the aeration rate into an air bubble loading model. Lynch et al. (1981) used an empirical model to relate the proportion of slow floating particles to the ratio of collector per ton of ore. Such empirical relationships are difficult to calibrate and cumbersome to use when an activator and a collector are added to slurries in which particle size distribution and surface characteristics are changing. Eascur and Herbst (l982) relate in a fundamental way the mineral flotation rate constants to the aeration rate, froth depth, agitation and frother concentration, however the model does not account for reagent flowrates. Niemi et al. (1982) have proposed a model for the conditioning of minerals and included it into a conventional flotation simulator."

Jan 1, 1988

Innovation ? In economics a change must increase overall value, customer value, or producer value. ? Innovations are intended to make someone better off, and the succession of many innovations adds growth to the whole economy. ? Innovation may refer to both radical and incremental changes to either products, processes or services.

Feb 1, 2008

By A. A. Goss

We investigate the relationship between corporate financial performance (CFP) and environmental and social performance (CSP) in a sample (n=165) of large, publicly traded U.S. mining and oil and gas firms. Using optimally scaled principal components analysis to generate aggregate measures of CSP strengths and concerns, we find higher concerns are related to higher volatility of unexpected earnings and discount rates. Furthermore, these earnings shocks are more likely to be negative as concerns increase. Decomposing this relationship shows that negative environmental performance dominates proactive environmental management as a driver of unexpected earnings, but proactive community efforts increase the magnitude of earnings shocks. We document some evidence of the strategic use of CSR, with those firms that have greater risk investing more proactively in CSR.

Aug 1, 2013

By Fulchand Shende

Around the world many potash mines experience brine inflow problems. The presence of brine in underground excavations may induce structural and stability problems. A study has been carried out to simulate the effect of brine on the performance of pillar support. The testing program consisted of loading potash specimens in a creep frame, and simulating inflows by continuously pumping brine into an experimental cell. Brine temperatures and load conditions were varied to simulate several mining and inflow conditions. Specimens were fitted with acoustic emission transducers to monitor energy emissions during an eight-hour test duration. Samples of brine were also collected to provide K+ and Na+ concentration data necessary for an accurate assessment of the dissolution process. Test results indicated that dissolution rates are highly dependent on brine temperature and load conditions. Loads approaching 50% UCS tend to generate very high rates of energy emissions, often leading to the failure of the simulated pillars. This study demonstrated that acoustic emission could be effectively used for predicting the performance of pillars when exposed to inflow brine.

May 1, 2001

By R. B. Allen, E. E. N. Smith, B. C. MacDonald

"LocationTHE MAIN PROPERTY and townsite of Eldorado Mining & Refining, Limited, Beaverlodge Operation, is on the north shore. of Beaverlodge lake, •about seven miles north of the deserted town of Goldfields on lake Athabasca, and four hundred and ninety air-miles equidistant from Prince Albert, Saskatchewan, and Edmonton, Alberta. Both Eldorado Airlines •and Canadian Pacific Airlines maintain scheduled flights from Edmonton to the 4,000-foot airstrip on the north boundary of the Company property. Bi-weekly flights are made by Saskatchewan Government Airways from Prince Albert. Men and priority freight are flown by Company aircraft direct from Edmonton. From June to-September, when the waterways .are ice-free, freight is carried by barge from the •railhead at McMurray, Alberta, down the Athabasca river to Chipewyan, and across lake Athabasca to• Bushell, the terminal on Black bay, lake Athabasca, a total distance of 265 miles.The Eldorado Operation has been connected by a 12-mile, all-weather highway to Bushell. Where the highway crosses the park-land along the Fredette river, the townsite, Uranium, is under construction to provide services to the uranium-producing district. Spur roads have been built to the Ace, Fay, Eagle, •and Martin mines of the Eldorado operation, and to the properties of Pitch-Ore Uranium Mines, Ltd., and Rix Athabasca Uranium Mines, Ltd."

Jan 1, 1954

By Hongpu Kang

The fully mechanized top coal caving mining method has been the main mining approach for thick coal seams with high output and efficiency in Chinese coal mines. The gateroads for the top coal caving mining faces should be driven along the floor of the thick coal seam with a part of the seam as roof. The support of the gateroads is commonly difficult because of the low strength and broken structures of the coal seams, and the increasingly large section of gateroads meeting the need of greater and greater face coal output. Based on the analyses on the geomechanics properties and production conditions of the top coal caving mining, the influences of the top coal caving mining parameters on the stability of gateroads, including mining thickness and face length, are studied. The deformation and damage features of the rock mass surrounding the gateroads with the top coal seam as roof are investigated, the interaction of the support with the surrounding rock mass, the support theory are studied. The bolting design method and criteria, bolting forms and parameters for the gateroads with the top coal as roof are put forward. The rock bolting components, including bolt bars, face plates, cable tendons, meshes, and steel straps, are introduced. Finally, the gateroad bolting effects are evaluated through a typical case study on the basis of field monitoring data, such as the displacement of surrounding rock mass and the forces along bolts and cables.

Aug 1, 2013