Search Documents

By A. G. Pathan

Rock and soil mechanics investigations were carried out in block VIII at Thar Coalfield, Pakistan. Most of the strata were mainly composed of sand, with an average content of 67.68 %. Laboratory studies of rock and soil samples from drill hole GT-01 revealed that the strata in block VIII are very weak with an average uniaxial compressive strength of 3.59 MPa, an average tensile strength of 0.68 MPa, an average Young?s Modulus value of 0.234 GPa, an average cohesion of 129.19 KPa, and an average friction angle of 55.47°. Slope stability analysis, based on a probabilistic approach, was carried out using Slide-V software. Monte Carlo simulations have been applied to investigate the probability of failure in the slopes of an open pit lignite mine in block-VIII. From the slope stability investigation, it was found that the probability of failure is 0 % at a slope angle of 16°.

Aug 1, 2013

By A. Kobzhanov, S. Saparova, S. Brochot, D. A. Mango

KATCO (an ORANO Mining and Kazatomprom joint venture) is the largest in-situ leach uranium mining operation in the world, exploiting the Muyunkum and Tortkuduk uranium deposits in southern Kazakhstan. After extraction from the deposits, uranium is then transported via a hydraulic network to be purified in three processing plants located near these deposits. Within KATCO, with the support of ORANO Mining and CASPEO, in 2018 and 2019, a large project that had as its main objective to improve the uranium accounting system was implemented. The objective of this paper is to describe this project and all the changes that it entailed. At KATCO plants, a black-box approach was previously used for uranium accounting. However, it is recommended to use all the available measurements and to deploy a data reconciliation model (between well-fields and plant) as the reconciliation uncertainty is overall lower and it provides a more accurate uranium balance. During the deployment of this project, the rules and algorithms to generate the uranium accounting report, the associated flow diagrams (for uranium accounting), the streams, units of operation, stocks, reporting and Key Performance Indicators calculation rules were re-defined.

Jan 1, 2020

By Stuart M. Jones

This paper is derived from a document that compiles autogenous and semi-autogenous mill installations worldwide, through the end of 2010. Updates have been solicited from all major mill manufacturers and most have responded. A review of AG/SAG mills sold to date and in the last five years indicates that the AG/SAG mill market is very healthy and the trend is larger diameter mills with high diameter-to-length ratios. Ring motors (gearless) are the preferred drives for large mills even though the power transmitted through a gear drive is expected to near 11,000 kW per pinion in the near future.

Aug 1, 2010

By Gilles Carrière

"The Suffield mine is situated five miles southwest of the city of Sherbrooke, in the Eastern Townships of Quebec. lt is the property of Suffield Metals Corporation Limited, a wholly owned subsidiary of Ascot Metals Corporation Limited.The old Suffield or Griffith mine had been worked intermittently from 1863 to 1906, without ever producing much ore. In 1951, diamond drilling done by Ascot Metals proved over one million tons of ore in three new bodies. The average grade of this ore was 0·018 ounces of gold per ton, 2-40 ounces of silver, l ·28 per cent copper, 0·59 per cent lead, and 6-45 per cent zinc. Since then the mine has been active, producing between 300 and 700 tons daily. More recent exploration has found continuations of the ore zones.General GeologyThe ore of the Suffield mine is found in porphyritic rhyolites of the Sherbrooke group (Silurian), at or close to its contact with sediments of the Beauceville group (Ordovician). The contact shows pronounced folds as well as irregularities due to erosion of the sediments prior to the outpour-ing of the lavas. On surface the general strike is north, and the dip is steeply east.The footwall sediments consist of interbedded black graphitic slates and. dark-coloured chloritic quartzite, overlain in many places by a thin bed of magnetite-hearing quartzite.The rhyolite host rock is a light grey rock, containing very abundant quartz and feldspar phenocrysts in a microcrystalline matrix of the same minerals. Some sericite is always present, especially in the vicinity of the ore zones, where the rock shows a pronounced schistosity.Several narrow basic dykes, with an easterly strike and vertical dip, cut all other formations. Most are lamprophyres, of either the monchiquite or camptonite type, but one has been identified as a diabase."

Jan 1, 1949

By Andrew D. Lapworth

The use of geological and grade models has been standard practice in mine design for many years now, with a wide range of software available to create and analyze the models. Although geotechnical parameters are also of vital importance for mine planning, there has been very little in the way of commercially available systems for integrating geotechnical data into the mine planning and design process. Sirovision is a new technology based on digital photography for automated, safe and accurate 3D mapping of geological and geotechnical features in rock faces. Datamine has integrated this capability into its product range so that Sirovision becomes an integral part of day-to-day face mapping, mine geology and geological / geotechnical modeling in both open pit and underground mines. This results in improved fragmentation for loading, hauling and processing, and for open pits local geotechnical conditions can be taken into account to improve slope design and control. This paper describes some of the ways that geotechnical modeling can be used to create more refined and cost effective mine designs and then discusses the role of Sirovision in enabling the raw data required for such modeling to be collected quickly, safely and reliably.

May 1, 2007

By Sophia Wong

Nickel is used in a wide variety of applications from consumer goods to industrial uses. In many of these uses, nickel contributes to the environmental attributes of the product. The challenge, however, is measuring that contribution, comparing it to the environmental cost of production, and communicating the role of nickel to the customer in a way that is easy to understand. This paper presents the Nickel Institute?s approach to climate change as a global commodity industry association, and discusses where we stand with regard to some of these key questions. It also identifies issues for the nickel industry moving forward ? challenges that are likely to be common to other commodities.

May 1, 2009

By Mori Fresko, Stuart M. Jones Jr

"This paper is derived from a document that compiles autogenous and semi-autogenous mill installations worldwide, through the end of 2010. Updates have been solicited from all major mill manufacturers and most have responded.A review of AG/SAG mills sold to date and in the last five years indicates that the AG/SAG mill market is very healthy and the trend is larger diameter mills with high diameter-to-length ratios. Ring motors (gearless) are the preferred drives for large mills even though the power transmitted through a gear drive is expected to near 11,000 kW per pinion in the near future.INTRODUCTIONThis paper is derived from a document that compiles autogenous and semi-autogenous mill installations worldwide. The list is maintained by Stuart M. Jones, Jr. (author), and is included in the appendix. This list has been the inspiration for similar papers in the past several SAG Conferences. Updates have been solicited from all major mill manufacturers and most have responded. Information from this list is compiled to illustrate the growth of the AG/SAG mill market and the use by industry and selected geographic areas. It covers the market growth through the end of 2010."

Jan 1, 2012

By A. M. Brown, P. V. Straznicky

Dimpling as a means of flush countersinking rivets is an old process predominantly used in secondary structures. The introduction of GLARE as an aerospace material has renewed interest in dimpling and its possible application in primary structures. The dimpling process is able to prevent the creation of a machined knife-edge in the thin aluminum plies of the GLARE sheets. In addition, dimpling eliminates the need to use reduced height rivets, such as the NAS 1097 rivet style. This investigation expands on an earlier study into dimpling of GLARE by Rans and Straznicky. In order to tailor the dimpling process to GLARE, FEM simulations were developed. After verification, a study was performed to find the best parameters for dimpling GLARE3-2/l. Coupon fatigue tests were carried out and the dimpled joints demonstrated increased fatigue lives over the conventional machine countersunk joints. Future wide panel fatigue tests are planned to confirm the usefulness of dimpling thin GLARE laminates.

Jan 1, 2006

By Esa Peuraniemi, Hanna-Leena Heikkilä

Boliden Harjavalta has been operating a copper flash smelter since 1949. Thus, in 2019, the smelter is celebrating its 70th anniversary of flash smelting. Slag formation is an integral part of the smelting process; currently the processing of slag is based on froth flotation at the slag concentrator. It provides high recovery of copper but restricts slag utilization; the final copper slag is deposited in a landfill. The Harjavalta smelter commissioned a new landfill area for final slag in May 2018. This paper describes the full project from permitting to commissioning of a new landfill area. The permitting process is described comprehensively, including environmental impact assessment together with the environmental and dam safety monitoring. During the environmental impact assessment, observations on rare animals protected on European level were made as well as archaeological findings. Successful completion of the permitting allowed the construction phase to start on time. After six years of intensive work, the new landfill was commissioned in May 2018. The new landfill area provides a sustainable way to store the smelter’s slag for decades to come. INTRODUCTION Slag processing Sulphide based concentrates have always formed the main raw material stream at Harjavalta’s copper smelter. During the smelting and converting steps, the iron included in the concentrate is oxidized and fluxed using a silica-based sand. Originally, the slag was processed by using an electric slag cleaning furnace after which the final slag was water granulated. Froth flotation has been utilized for slag treatment since 1966. In the beginning, the slag was cooled in open ditches. In 1984, controlled slow cooling of slag was licenced to enhance copper recovery at the flotation plant. Today, the slag from both the smelting and converting is tapped/skimmed to slag ladles and treated in the following steps: Slag ladle transportation from the smelter to the cooling area by slag hauler Slow cooling of slag in the ladle to allow mineral precipitation Unloading the slag by tilting the ladle; causing the slag to crush as it drops from the ladle Feeding the crushed slag (-500 mm) by wheel loader to a slag concentrator’s feed funnel followed by a conveyor belt transporting the slag to the concentrator plant Crushing and grinding using lump and pebble mills Froth flotation of the valuables Recycling the slag concentrate back to the smelter feed after dewatering Pumping the final copper slag to the landfill area.

Jan 1, 2019

By W. R. Lindsay

Anyox, where the Hidden Creek mine of the Granby Consolidated Mining, Smelting and Power Company is located, is situated on an excellent deep-water harbour in Granby bay, at the head of Observatory inlet, about 600 miles from Vancouver and 90 miles north of Prince Rupert. Anyox is the Indian name for the little stream which empties into Granby bay, and means 'hidden creek'. The Ore-Bodies The ore is a replacement deposit and occurs at and near the contact between argillites and a later intrusive greenstone. This contact locally has a general north-and-south trend, an irregular westerly dip, and in the vicinity of the ore-bodies there has been intense folding, accompanied by faulting. The mineralizing solutions supposedly were derived from the Coast Range granite batholith, distant one to two miles to the east and north. The whole area is cut by many dykes of varying widths, which seem to have had but little part in the ore deposition.

Jan 1, 1929

By D. W. Morgan, K. W. Downes

"OVER half a million tons of chromite ore is used annually on the North American continent, all of which is imported from overseas. Chromite is essential in the manufacture of stainless steel, armour plate, and tool steel, to mention only three important uses. It is, therefore, a strategic mineral, and every effort should be made to discover a means of utilizing our domestic supplies.Both Canada and the United States possess deposits of chromite, but they are low grade with respect both to their chromium content and to the ratio of chromium to iron. Mechanical concentration can improve the chromium content •by rejecting gangue, but chromium concentrate produced is still lower in chromium than imported chromite and, more important, the ratio of chromium to iron is only about half that in the imported material. At present, a chromium to iron ratio •of 3:1 is desired by industry. To obtain this .ratio in the case of domestic ores, a chemical attack on the chromi'e is necessary."

Jan 1, 1952

By Frederick Bird

This paper is based upon a review of studies of mostly Canadian mining companies in Chile, northern Canada, Tanzania, Guatemala, Ghana, Sierra Leone, and the Democratic Republic of Congo. In spite of often well-meaning efforts most mining firms produce wealth in developing areas that largely benefit those immediately involved, sometimes neighboring communities, and often those in the governing strata. Typically mining takes place in enclaves and fosters enclave development, rather than the kind of inclusive wealth development favored by the recently UN published Inclusive Wealth Report. One way by which mining operations can foster more inclusive wealth development is to adopt much broader approaches towards the construction of the various physical and social infrastructures ? roads, water, electricity, health services, schools, security ? required for their own operations by collaborating with diverse regional, provincial, and/or national agencies and businesses to develop these infrastructures for larger populations and areas beyond the immediate sites where they are operating. Established mining firms can also foster more inclusive wealth development by establishing more formal, collaborative relationships with artisanal miners.

Aug 1, 2013

By E. S. Moore

To properly understand industrial conditions in Spain it is necessary to consider the early history of the country. Spain is very backward in many lines. They use the sickle for cutting grain, and plows for cultivating the land, which resemble those of Biblical days. In the great mining camp at Bilbao only one steam-shovel is in use, although about two hundred million tons of ore has been produced, and this almost entirely from open cuts. It is the lack of industrial development, such as is found in many other countries, which permits large mining enterprises to be controlled almost entirely by foreign capital, although Spain is such an old country, and which permits mines opened in the days of the Phoenicians to still operate. Such deposits in America would be exhausted in a comparatively few years. The Phoenicians are supposed to have reached Spain about 1100 B.C. and to have worked some of the properties in the Rio Tinto district. The Carthagenians invaded the country about 236 B.C., and they were driven out about 205 B.C. by the Romans. The Romans ruled until 483 A.D., when they were overthrown by the Visigoths. Then, about 711 A.D., the Moors from Africa became prominent and they were finally expelled by the Spaniards in 1492. Spanish power reached its zenith under Phillip II, during the latter half of the 16th century, and since the close of that century the country has lost its prominent place among the nations. There are some evidences of revival in the development of good roads, the construction of a satisfactory network of railways, and the building of magnificent thoroughfares through the capital city, Madrid.

Jan 1, 1927

By L. Dufourm

This paper presents a review of plant layout considerations incorporated into recent designs of SAG/Ball mill circuits for two medium sized concentrators. The plant layouts presented and the design concepts discussed, relate to smaller SAG circuits, but can equally apply to larger milling circuits. Included are design concepts and ideas introduced by the various project teams, and the focus is on the primary factors of any layout design which are safety, constructability, operability, and capital cost.

Jan 1, 2012

By T. Scully

Since early days in coal mining, it has been known that some coals and the carbonaceous materials associated with them will heat and fire spontaneously. Many theories have been advanced to account for this phenomenon, but it is only within comparatively recent years that any scientific research has been carried out to determine the causes of this heating, the conditions which bring about its occurrence, and the reason why different coals heat with a varying degree of readiness. So far, this research has not cleared up these points entirely, but a great advance has been made in our knowledge of the matter. In general, any coal will fire spontaneously, although with a varying degree of readiness, provided conditions for its doing so are favourable enough. These conditions are that the coal must be in a fine state of division, that sufficient oxygen must be present for rapid oxidation, and that the air current passing must be so small that it is insufficient to carry off the heat produced by this oxidation. Many other minor factors, however, contribute to bring about spontaneous heating, either by producing initial heat themselves or by inducing the other major conditions.

Jan 1, 1931

By Laurence D. Burke

The electrocatalytic behaviour of gold in aqueous media is surprisingly complex and a novel view of gold electrode surfaces is proposed to explain the observed electrochemical responses. The metal surface is considered as a chemically (or redox) modified electrode, with equilibrated, low energy, surface gold atoms functioning as a relatively inert support and low coverage, high energy, protruding gold atoms (or minute clusters of same) functioning as electrocatalytic redox mediators. The protruding atoms are viewed as surface active sites and the complex electrocatalytic behaviour is attributed to the basic instability of the mediators, the diversity (and poor control) of same, and the acid/base (or hydrolysis) behaviour of the oxidized states of the mediators. It is assumed that major advances in the application of gold in the heterogeneous catalysis of gas phase reactions will be accompanied by similar advances in the use of gold in the electrocatalysis area; however, this will require considerable work of both a practical and theoretical nature.

Oct 1, 2003

By I. Kirman, B. Waters

World wide applications for nickel use will be summarized and examples of those uses given. Nickel products are critical to many important aspects of modern society. These products are just as important for modern China as they are in other parts of the world. It is argued that future pattern of nickel use in China should be expected to be very similar to that in the rest of the developed world. Total use of nickel in products in China is already very large. In 2004, it was the largest market for stainless steel (nickel containing) in the world. A survey of Chinese stainless steel applications will be presented. Current high nickel prices have revived speculation about substitution, particularly for nickel containing stainless steels. The presentation will discuss some of the complicating factors that need to be taken into account when considering substitution. These factors are as valid in modern China as they are in other developed economies. Recent substitution efforts and the reaction to them will be examined. The Nickel Institute position regarding appropriate application of the various grades of stainless steel will be discussed. Price-motivated substitution in China, and elsewhere, will occur but it is argued that the extent will probably be limited.

Jan 1, 2005

By Pierre Bénard

To achieve penetration on the energy market, hydrogen must overcome obstacles in the areas of storage, safety and infrastructure. One of the most important is the onboard storage of hydrogen for transportation applications, where large performance gaps exist between the current state of the technology and user expectations. In order to develop and demonstrate viable hydrogen storage technologies for cars, a set of gravimetric and volumetric system targets have been proposed by the US Department of Energy, based on achieving a driving range of 500 km for a hydrogen powered vehicle. A factor of 2 to 3 improvement in both hydrogen storage capacity and energy density is needed along with several other performance goals. Another key issue is safety. Although some of the safety issues can be arguably assigned to misperceptions, hydrogen has specific properties that have to be addressed, particularly in confined geometries where the risk of hydrogen detonations becomes an issue.

May 1, 2007

By Bruce Chalmers

INTRODUCTION TIE most important practical problem with which Physical Metallurgy is faced is the control of the mechanical properties of alloys. The most difficult aspect of this problem is the development of new alloys with the properties that are required for meeting exacting engineering requirements. A great measure of success has been achieved by following the empirical method and most, if not all, of the present variety of alloys have been developed by the process of experiment and observation or trial and error. It may, however, be that this method will become. less productive as time goes on, and that eventually it should be replaced by a process based on an understanding of the factors that determine the properties, so that alloys can be 'designed' to meet the requirements. This method of investigation will not be possible until a much better fundamental understanding of metals has been gained, and this will come only about as a result of a great deal of detailed research. The subject of Physical Metallurgy can be divided, as follows, into two parts: we may consider the factors which determine the structure, in the broadest sense, of an alloy. These include the composition and also the treatment to which the material has been subjected. The second aspect is the influence of the structure on the mechanical and other properties. In order to make an effective contribution in this field, it is necessary for an individual or a group to concentrate on a specific and very restricted topic. It is proposed to discuss in some detail the particular subject in which the writer and his colleagues are working.

Jan 1, 1951

By Karl J. C. Harries

"14.1. INTRODUCTION1The boilerplate of an agreement is not a single provision, but a series of provisions that are expected in “every agreement”. They are sometimes also referred to as the “lawyer’s provisions”. Many businessmen consider the boilerplate to be superfluous and, to some extent, window-dressing by the lawyers – even legalese. They will often offer advice to the effect that it can “pretty well be ignored”. Such advice could not be more wrong.Most boilerplate provisions are essential parts of every agreement. Some may be part of a “standard package” and may have little relevance to the agreement at hand, but these are the exception rather than the rule. The exceptions should not be treated as justification for giving all these provisions short shrift. The boilerplate should receive the same review, consideration, and negotiation as the provisions that set forth the business deal. It is often these provisions that make the deal work or that are turned to at the time of disputes. If they are inadequate, as they sometimes are (unfortunately, some draftsmen are also loath to review or update their standard boilerplate provisions or to tailor them to the deal at hand), they can create problems, rather than offer solutions. Such problems can be costly and time-consuming for the parties to address. Inadequate or incomplete provisions may ultimately be one of the reasons for the parties to turn to the courts to settle their differences. On the other hand, good boilerplate provisions can help keep them out of the courts.One of the principal objectives of an agreement should be to provide procedures, or mechanics, for implementing agreed principles and for the parties to follow to settle their differences, real or perceived, without going to the expense and disruption of a lawsuit. An agreement should aim to keep the parties away from the courts, not serve as a springboard to the courts. It must nevertheless be acknowledged that, if there is a major falling-out among the parties to an agreement, the chances are that, however carefully the provisions of that agreement have been negotiated and drafted, the parties will end up before the courts or some other adjudicating body."

Jan 1, 2003