Search Documents

By P. B. Marchant

"Based on laboratory and pilot scale continuous biooxidation of complex sulphide concentrates, commercial processing design and scaleup considerations are discussed. Capital and operating cost estimates for commercial biohydrometallurgical operations are summarized and potential applications of biotechnology are discussed. Biooxidation as an oxidative pretreatment alternative to enhance precious metals extraction from refractory sulphide concentrates in stirred tank reactors has received considerable attention recently due mainly to advances in the practical applicability of the process. Biooxidation of sulphides is certainly not a new process, however, application and control in large scale hydrometallurgical operations to treat refractory sulphides remains conceptual and the limited data available is restricted to relatively small laboratory and pilot scale operations. It is the intent of this paper to indicate scaleup and plant scale process design considerations for commercial bioleach circuits, based on recent operating experiences with laboratory and pilot scale continuous bioleach systems. An indication of the expected range of applications will be presented parameters for optimization will be discussed."

Jan 1, 1986

By Alexander Smith

Surf Point and Edye Pass mines are on the northwestern part of Porcher island; 25 miles southwest of Prince Rupert. During the 1930's they produced about $750; 000 in gold from ore averaging better than one-half ounce a ton. The deposits are quartz veins; containing auriferous pyrite; concentrates average about 8 oz. gold a ton. The veins occur in a quartz diorite; stock. Their distribution shows an apparent control by primary flow structures; for the principal deposits lie on the axis of an arch of flow layers. The technique used in mapping the structures in the intrusive is that known as the Cloos method and described by Balk.

Jan 1, 1954

By J. S. Stewart

THIS paper was prompted by a persistent demand for what information we have that will throw light on the oil and gas possibilities of the Maritime Provinces. The problems involved were made familiar to the writer during three seasons of field work in New Brunswick and Nova Scotia. The reasons for renewed interest are: (1) In many parts of that region, the surface is underlain by a thick series of unaltered sedimentary rocks. (2) Oil seepages occur, and oil in commercial quantity has been exploited' near Moncton, New Brunswick, for many years. (3) In recent years, a new method of attack has been developed toward the finding of stratigraphic traps. This method is based on a detailed study of the geological history of the region, as revealed in surface outcrops and samples from deep wells. The well samples show the lateral variation of strata, far from any possible surface outcrop of the same beds. Sufficient work has now been done in the Maritime Provinces to reveal the broad features of the geological history and the character and distribution of the various rock formations. Comparatively little deep drilling has been done in this region, but the holes are widely scattered and the samples from them have added much to the information obtained from the numerous outcrops of bed-rock. The following discussion gives a summary of available information that has a bearing on the subject.

Jan 1, 1943

By A. Mular, T. Bond, G. D. Farnell, J. F. Kingston

"ABSTRACT:-A 60—cm semiautogenous grinding-(SAG) mill was designed -for continuous wet operation in closed circuit with a vibrating screen. The circuit is fully instrumented and automated. Part of the control system incorporates Foxboro SPEC 200 controllers around the pump box to maintain level. The rest of the control system involves an ACTION model BC2 basic direct digital controller that handles all other inputs/outputs and contact closure sensing:·The success of the control system is attributed to the uniqueness of specially designed mass flow metering systems. Various control strategies are possible. Employed to date has been control of a mill load set-point by cascading the deviation from load set-point as the set-point to the fresh feed rate ""controller"". Mill feed water is ratioed to total flow rate of solids fed to the mill. The performance of the circuit is being correlated with the performance of full scale SAG circuits in British Columbia to develop models, to assess the feasibility of scale up and to investigate the effects of design variables on responses such as circuit throughput. 1 INTRODUCTIONWhere ore types are appropriate, semiautogenous grinding and/or autogenous grinding (AG) has replaced conventional grinding. Secondary/Tertiary crushing plants are thereby eliminated so that capital expenditures are less and overall comminution costs can be lower (Barratt 1982). To establish the suitability of an ore for SAG circuits, pilot scale tests with 1.7 to 1.8 M diameter mills are often conducted. At least one test per ore type in a deposit has been necessary. Often, each test involves a large amount (up to 50 tonne) of sample, so that the testwork can be expensive and may discourage the use of SAG or AG circuits. However, MacPherson (1977) has employed a continuous 45 cm dry Aerofall mill circuit closed with screens and an air classifier to determine whether ores are suitable for SAG milling. The amount of sample per ore type is of the order of 60 kg or less. Thus an established SAG mill scale up procedure that employs small circuits is highly desirable.The purpose of this paper is to describe a small 60 cm wet continuous SAG/ AG mill pilot circuit assembled at the University of British Columbia to study the feasibility of scale up, to assess the influence of design variables, to develop mathematical models and to evaluate the effects of alternative control strategies on circuit performance"

Jan 1, 1988

By John D. Godfrey

Precambrian Shield rocks, exposed in the extreme northeast corner of Alberta, provide the only possibility for a granitic building stone development in the province. Among a wide variety of granitoid rocks in the Shield, the Chipewyan Red Granite is one of the most favourable prospects. Geological mapping and exploration has revealed two prospective sites within a major pluton situated close to navigable water. Cleaned outcrop surfaces show clearly the pattern of joints and lithologic variations within the granite at prospective quarry sites. Other features include: basic dykes, quartz veins, and sheeting fracture zanes. Systematic orthogonally arranged fracture sets and the sheeting zanes are auributed to a tectonic origin. onsystematic irregular fractures are related to surface and nearsurface processes, such as decompression through unloading .

Jan 1, 1984

By M. Kamyab

Transportation of fluid and slurry (fluid and solid particle mixtures) in a pipe and annulus space has been the focus of numerous studies. There are different parameters to be considered when studying slurry transportation. These include slurry velocity or flow rates; fluid properties such as density and rheology; and solid particle properties including concentration, density, shape and size. Also the angle of the flow conduit, rotation of the pipe and possible eccentricity of the annulus are other factors which influence slurry transport characteristics. Although a number of analytical, numerical and empirical equations as well as numerical simulations have been developed for studying the flow and slurry transport characteristics, the results need to be validated against either field or lab data. As performing field tests is costly and time consuming, conducting simulations at the laboratory scale appears as a good alternative. Different flow loops have been designed to study slurry transport behaviour in different science and engineering disciplines including oil and gas and mining. However, few of these consider, in particular, cuttings transportation in small size annulus space. The flow characteristics appear to be very different when slurry travels within a small size annulus, in particular when the fluid velocity is high. In this study, a review of some of the existing slurry flow loops will be conducted. Then the details of a slurry loop, which has been designed and commissioned for the purpose of studying cuttings transport in a small size annulus space for applications in drilling mineral exploration wells using coil tube technology, will be presented.

Aug 1, 2013

By M. Tadie, J. Wiese, K. Corin

The use of potential control in the flotation of ores has been applied in a variety of operations and presents an opportunity for improvement of selectivity and recovery of valuable minerals. Although it is possible to vary the redox potential (Eh) using chemical additives such as sodium hypochlorite or hydrogen peroxide this is more commonly done by varying the pH and dissolved oxygen (DO) concentration. The present study involves an investigation into the effect of varying dissolved oxygen concentration, ionic strength (IS) and pH on the flotation response with the aim of application to a South African lead-zinc ore. In all cases the Eh is measured as a function of the different DO, IS and pH values. The main objective was to achieve selective flotation of galena from sphalerite. The first part of the work was micro-flotation tests conducted on single minerals with galena used as the basis for effect of the factors studied on redox potential and ultimately recovery. The DO was varied by alternating between the use of air and nitrogen as the gas source to the micro-flotation cell. PH was varied between pH 9.2 and pH 11.8 using sodium hydroxide. In the first part of this study a factorial design approach was used to determine the interactive effects of the variables tested, viz. DO, ionic strength and pH, on the Eh and on the recovery. Redox potential was measured using a combination electrode made up of platinum wire and Ag/AgCl reference combination. Recoveries indicated that pH had the most significant effect on recovery and Eh. The influence of redox potential on recovery was found to be of relevance to the condition of high dissolved oxygen concentration and less so at low dissolved oxygen concentrations. It was also noted that that the combined interaction between ionic strength and dissolved oxygen concentration had a positive effect on recoveries, however this was not so with Eh. The chemistry of the ions in solution was observed to play a dominant role on the recovery due to changes in solubility arising to pH modification. The longer term objective of this work is to determine the optimal Eh conditions for the separation of galena from sphalerite.

Jan 1, 2016

By I. H. Redeker

North Carolina is the leading state in the USA in feldspar, mica, and spodumene production. Mixed feldspar, spodumene, mica and quartz are mined from hard rock, open pit deposits and recovered by flotation from the fresh pegmatite type ores. Potash feldspar, mica, clay and quartz are recovered from weathered decomposed pegmatites. The North Carolina State University has a Minerals Research Laboratory in Asheville with trained personnel and flexible pilot plant equipment. The flowsheets for the feldspar, spodumene and mica producing companies and for large phosphate and glass sand flotation plants were developed and tested in Asheville. Examples and problems of pegmatite flotation are demonstrated with flowsheets and slides.

Jan 1, 1981

By G. F. Miller

ONLY IN THE Province of Saskatchewan is natural sodium sulphate found in Canada in amounts large enough to make recovery economically sound. Geologists have estimated that the numerous deposits within the Province contain upwards of 200 million tons of Glauber's salt. There are twenty-one deposits in the Province which contain 500,-000 or more tons and about two dozen with lesser amounts. The first recorded production of sodium sulphate in Saskatchewan was in 1918. The company concerned, and others that attempted to develop the industry in its early stages, were unsuccessful. Their failures were caused by two main factors -lack of knowledge of efficient operating methods and the unstable market situation for the finished product. Today, the situation is changed in both respects and the product, commonly referred to as 'saltcake", is a very important chemical requirement of many industries throughout the world. Before proceeding with remarks on manufacturing methods it should be stated that, although this is a general paper on the manufacturing methods and end uses of the saltcake produced in the Province, the writer is, of course, more familiar with the plants operated by Saskatchewan Minerals than with other operations and perhaps may be excused for dealing more particularly with the plants of that Compa11y.

Jan 1, 1958

By J. B. Mawdsley

A LITILE north of the geographic centre of the Province of Saskatchewan, 150 miles north of the city of Prince Albert, is a narrow green-stone and sedimentary belt of pronounced structural characteristics. This belt, generally known as the Sulphide Lake belt, is about two and a half miles wide. During the past three years prospecting has uncovered numerous gold-bearing showings occurring chiefly along the centre of the belt for a distance of at least nine miles. The number of these showings, the nature of some of them, and their relationship to strong structural features, make it altogether likely that intensive work will eventually locate ore-bodies that will be of economic importance. The discovery of gold in the fall of 1938 on the south shore of Mackay lake, about five miles northwest of the Sulphide Lake gold-bearing belt, indicates that there are neighbouring zones of interest. This paper, an attempt to outline the present status of the interesting mineralized belt, is based largely on the information gained on a five-day tour of this district, made in August, 1939, on behalf of the Department of Natural Resources of the Province of Saskatchewan. The Sulphide Lake belt is named after a small lake centrally located in it. This lake and others are just north and within short portage distances of some of the long bays along the north shore of Lac La-Ronge, an irregular, island-studded lake, about twenty miles in diameter, in relatively rocky Precambrian country, just north of the Palaeozoic contact. The fur-trading post and settlement of Lac La-Ronge is on the west shore of this lake and a road, now under construction, will shortly link this community with the city of Prince Albert. In the past, the most direct route was an indifferent canoe route, in part following Montreal lake and river; more recently, the aeroplane has made this section easily accessible.

Jan 1, 1940

By G. Song

Magnesium has excellent bio-compatibility in terms of its density, strength, elastic modulus and toxicity. However, due to its poor corrosion performance, so far magnesium has not been successfully used in the human body as a permanent implant material. Nevertheless, there is a possibility to utilize the low corrosion resistance of magnesium to make magnesium into a temporary implant component that can gradually dissolve in the human body after surgical region heals. This will avoid the secondary operation to remove the temporarily implanted component and the chronic inflammatory discomfort caused by the implant. This paper is aimed at exploring the possibility of using magnesium as a degradable bio-material through investigating the corrosion behaviors of pure magnesium and surface treated magnesium in a simulated body fluid (SBF) solution. It was found that magnesium corroded rapidly in the SBF solution, resulting in vigorous hydrogen evolution and a strong alkalization effect. Hence, it is impractical to use magnesium as a permanent implanted material or even a degradable implant. However, a proper anodizing treatment can significantly improve the corrosion resistance of magnesium, and hence slower down the hydrogen evolution and alkalization processes, which will allow to control the corrosion or degradation of magnesium at a desired rate in the human body. With a controllable corrosion rate, it is believed that magnesium as a degradable implanted material will be eventually achievable.

Jan 1, 2006

By Jessica Hurst, Mark Holdsworth, Jeff McKay

"In 2002, Kennecott Utah Copper Copperton Concentrator installed an Expert Control system for optimization of their SAG and Ball milling circuits. The advanced process control has been well received and is utilized well over 95% of the time. In the years since, many lessons have been learned and many advances have been made. Improvements have produced millions of dollars of benefits and have included directly controlling feedrate with complex logic as opposed to using a bearing pressure controller, modifications to how sound is used for control, modifying logic for maximizing asset utilization and using advanced control for automating equipment restart. INTRODUCTIONRio Tinto’s Kennecott Copperton Concentrator produces copper, molybdenum, gold and silver. The mill has 4 SAG mills (SAG 1-3, 34 foot diameter and SAG 4 36 foot diameter), 8 ball mills and copper and molybdenum flotation plants, as seen in Figure 1. The 2010 average data is shown in Table 1.In 2002, a Metso Cisa OCS Expert Control system was installed at Copperton for SAG and Ball mill advanced control. The expert control was first placed on SAG 2; data from the first few weeks compared with operator performance indicated approximately an 11 percent increase in throughput. After full commissioning, the system was gradually refined further by plant personnel to develop key performance indices based on SAG feed size, refinement of the sound setpoint for control of mill speed and throughput, specific rules to help the adjustment of speed based on loss of a feeder, etc. With the addition of the pebble crushing circuit, the expert control began utilizing a model estimation of crushed pebble bin level to help stabilize the impact of returned crushed and uncrushed pebbles on the SAG mills. As the ore and limitations change, it is necessary to evolve the SAG logic to better handle any constraints."

Jan 1, 2012

By B. Krysa, A. Mitsui, T. L. Koehler

The presence of arsenic, even at trace levels, in copper processing leads to the risk of arsine gas where reducing conditions exist that can reduce any soluble arsenic present to its minus 3 valance state and generate hydrogen gas from the solutions. This risk is understood to be significant within the industry, particularly in the case of liberator cells where copper concentrations in solution are drawn down to remove the copper and impurities from the bleed stream. However, there are numerous other potential areas where the arsine gas risk exists including contact between active metal such as iron, zinc or aluminum and arsenic bearing solutions in pyrometallurgical dust treatment, refining and acid plant operations. In turn this breaks down to different mitigating strategies dependent on the risk scenarios considered; for example, how this risk interacts with Change Management, Confined Space Entry or Contractor Training. The ISO 45001 is an emerging standard meant to improve employee safety, reduce workplace risks and create safer working conditions all over the world. The paper shows a case study of how a framework consistent with the tenets of ISO 45001 has been used to provide a consistent assessment of this risk for a wide variety of copper operations and the expectations of how this may be used to effectively improve the effectiveness of barriers against future incidents. INTRODUCTION Arsine gas (AsH3), first identified in 1775, is a highly poisonous, colorless, non-irritating gas with a mild garlic odor that is heavier than air. Arsine gas is generated when reducing conditions are generated in the presence of hydrogen ions and arsenic compounds. Present permissible occupational exposure limit as defined by Occupational Safety and Health Administration (OSHA) as an 8-hour time-weighted average is ppm (0.2 mg/m3). Further increasing the risk, conventional respiratory protection utilizing half or full masks with gas filtering cartridges provide minimal protection against arsine. In copper processing plants, the risk of arsine generation is well understood in liberator cells, which are part of the electrolysis process. In this process, solutions containing copper are reduced in copper concentration removing not only the copper, but also arsenic, antimony and bismuth. The residual solution can be bled to control impurity build-up in the refinery. In this process, if the copper concentration is reduced to the point where As3- can form, arsine gas is generated via reaction with hydrogen ions generated during the plating process. The copper concentration at which arsine gas is generated depends on copper concentration at the cathode surface, the temperature and the acidity. As a result, there is always a risk of arsine gas generation in the liberator cell. Process measures to minimize or mitigate arsine evolution are tight control on final copper concentration, warm temperatures, fresh feed distribution and internal acid recirculation rates. Operator exposure protection measures are hooding, ventilation, arsine detection systems, restricted personnel access, automated shutdown controls and pre-defined evacuation plans.

Jan 1, 2019

By Curtis Rempel, John Bartlett, Alex Holtzapple

METSIM is a powerful program capable of modelling and simulating every known metallurgical and inorganic chemical process. METSIM is used by companies throughout the world to design, simulate and control operations from mine to tailings and everything in between. At its absolute simplest, METSIM can be used to create a process flowsheet. METSIM modules and built-in unit operations cover mass and energy balances for either steady-state or dynamic simulations of mine, stockpile, heap leach, material handling, comminution, beneficiation, hydrometallurgy, pyrometallurgy, gas and steam handling, and tailings management processes. Data for the material being processed can include mineralogy, particle size analysis, grade by size or multicomponent size analysis, washability data, mechanical, physical and thermodynamic properties. METSIM is written in APL (A Programming Language). Unlike C++, APL is simple and easy to learn, allowing the user to program whatever they can imagine, without first obtaining a degree in computer science. METSIM can also interface with EXCEL and other software through dynamic data exchange (DDE), allowing data to be imported and exported for viewing, analyzing and controlling. METSIM can answer simple or complex metallurgical and process questions allowing the user to predict and engineer without the issues of clumsy and tortuous spreadsheets.

Jan 1, 2014

By Brian K. Ayres

Inco Limited, Ontario Division is currently in the process of decommissioning the Whistle Mine site located near Sudbury, Ontario, Canada. The most significant component of site decommissioning involved relocating approximately 6.4 million tonnes of acid-generating waste rock to the open pit from two adjacent stockpiles. An engineered cover system was designed for the backfilled pit to reduce the long-term production of acid rock drainage. Geochemical modelling was conducted to assess the effectiveness of various cover options on the longterm water quality of the backfilled pit. Results obtained from performance monitoring of cover system field trials at the site and estimated full-scale construction costs were used to select an appropriate material for the cover system barrier layer. The two-dimensional soil-atmosphere model VADOSE/W was used to develop a calibrated model of covered waste rock based on field data obtained from the cover trials, which was subsequently used to predict net percolation and oxygen ingress through various cover system alternatives for site-specific climate conditions. Erosion and landform evolution numerical modelling was completed to assist in designing the runoff management system and final landform for the pit cover system. The potential impact of various physical, chemical and biological processes on the sustainable performance of the pit cover system was also considered in the design process. This paper provides an overview of the design and construction of the backfilled pit cover system.

Apr 1, 2005

By E. Yan, M. Mankosa, E. B. Wasmund

Mechanical cells are the dominant unit operation in base metal rougher flotation applications worldwide. As economic demand for metals increase, and as the feasible ore grades decrease, the installed capacity of mechanical flotation units worldwide has greatly increased, adding significant capital and operating cost. One opportunity to improve this situation is to use fundamental knowledge to make the industrial flotation process more efficient. A key insight is that the flotation process can be optimized by dividing the processing of the pulp into two distinct fluidic environments; a collection cell where air and pulp mix in a highly energetic compartment, and a low energy gravity separation cell. This is the basis of the “2-stage flotation device” that has been patented by Eriez and marketed under the tradename StackCell™. Two industrial case studies will be presented to highlight the potential metallurgical and commercial advantages of the StackCell. In the first, a train consisting of three pilot scale StackCells (each 0.6 metre diameter) was run in parallel with a train of conventional mechanical cells in a major copper concentrator and benchmarked against a batch Denver test. In the second, the performance of a 3 metre diameter StackCell in a nickel sulfide cleaning application was benchmarked against a batch Denver test. The flotation kinetics observed in the StackCells were 2.4 to 2.9 times faster when compared with the lab Denver test. In the first case study, the kinetics of the StackCell was about six times faster than conventional mechanical cells. It is hypothesized that the efficiency improvement in kinetics is because of reduced “drop-back” during the froth recovery phase, which is reduced because of the reduction in the shear that is present in a conventional mechanical tank cell. This result suggests that a 2-stage flotation system can be used to reduce the working volume of flotation units by five to six times. This would allow operators to significantly reduce the size of their flotation lines for a comparable flotation objective. Some discussion will follow about the scale-up criteria, maintenance and operability issues, comparisons of layout, and possible cost savings. INTRODUCTION The solution that most equipment suppliers have offered to reduce the cost of mechanical flotation equipment over the last 30 years has been to increase the size of the flotation unit cell (Mankosa, 2017). For example, three 100 m3 machines with three smaller motors, mechanisms and control valves could be replaced with a geometrically similar 300 m3 with a larger version of each ancillary component. While there are some efficiencies and cost improvements to be gained by this approach, it does not take advantage of fundamental insights into the flotation process, and it does not represent a step-change in terms of process design or economic benefit for the customer. The advantage of the “bigger is better” approach is that there is past experience of incremental improvements by making cells larger and there is a well-established scale-up method, which allows practitioners to estimate equipment capital costs based on very simple laboratory test- work. A different paradigm, which is gaining interest rapidly is to use a unit operation in which it is easier to optimize the flotation process, which will be described in this paper. This approach is often referred to “2- stage flotation”. Because this approach is new, it is important to benchmark it against existing conventional technology and to demonstrate a robust methodology for sizing equipment and flowsheets. This paper aims to address these issues with two case studies.

Jan 1, 2019

By J. O. Yeboah, V. Boakye, P. A. Bepswa, M. Lombard, G. Nutor

The comminution circuit at Tarkwa Gold Mine was commissioned as a Single Stage SAG mill operated in closed circuit with hydrocyclones designed to process 4Mtpa. The circuit was later expanded by adding a secondary ball mill in closed circuit with hydrocyclones with a view to treat 12Mtpa. The change in the circuit configuration and assigning the low aspect ratio SAG mill for primary grinding application makes the Tarkwa experience unique in terms the optimisation strategy and operating philosophy. This paper reports the findings from a series of surveys performed on this plant. The surveys reported include data obtained when the SAG mill was operated as a single stage mill in closed circuit with hydrocyclones and also SABC mode under two different feed conditions. The differences in operating philosophy between the initial single stage SAG circuit and the current SAG/Ball mill circuit are discussed.

Jan 1, 2012

By Suzie Poulin, N. Geoffroy, G. P. Demopoulos

Most metallurgical industries generate toxic waste that must be treated prior to being released to the environment. However, in a lot of cases, the waste materials are poorly characterized or the analytical results are not well interpreted. These shortcomings often result in the development of inefficient industrial procedures, thus causing economic waste and difficulty meeting environmental regulations. Fortunately, a wide range of analytical techniques are available to guide researchers and engineers into making sound process development decisions. In this work, an industrial selenium and mercury removal process is used as an example to illustrate the application of X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) coupled with Energy-dispersive X-ray spectroscopy (EDX) and powder X-ray diffraction (PXRD) on solid waste. Furthermore, samples of analytical results are presented and interpreted and the modifications to the industrial process that resulted are explained. Finally, a brief description of the advantages and limitations of the aforementioned analytical techniques is given with an emphasis on industrial solid waste material.

Jan 1, 2011

By J. D. Jones

The geographic occurrence of economic mineral deposits presents a variety of problems in modern tailings disposal operations. This paper presents case histories in several sectors of the mineral industry as well as the several stages of operations planning required for new designs, system expansion, reactivation of abandoned systems and upgrading to present environmental standards.

Jan 1, 1978

By Y. Nishida, Y. Nara, T. Ishida

Understanding time-dependent deformation and fracturing in rock is essential, because the information of the long-term stability of rock is required for many sub-surface structures excavated in a rock mass. Time-dependent fracture propagation has been invoked as a potential key mechanism responsible for the increase in seismicity preceding earthquake ruptures. In engineering projects and in preventing natural hazards, the study of time-dependent fracturing is necessary. Subcritical crack growth is one of the main causes of time-dependent fracturing in rock. For silicate rocks, subcritical crack growth has been investigated by various researchers. It has been clarified that surrounding environmental conditions (temperature, humidity, and existence of water) have strong influence on subcritical crack growth in silicate rocks. Therefore, the information of subcritical crack growth in silicate rocks has already been enough. On the other hand, information of subcritical crack growth in carbonate rocks is not enough. Especially, the influence of surrounding environment on subcritical crack growth in carbonate rock has not been clarified yet. In this study, we investigate subcritical crack growth in carbonate rock experimentally using a fracture mechanics testing method. Marble obtained in Skopje in Macedonia is used as a carbonate rock sample. The Double Torsion method is used to measure the crack velocity and stress intensity factor. Especially, influence of water on subcritical crack growth in Macedonian marble is investigated. It was shown that the crack velocity in water is much higher than that in air at the same temperature. Based on the results of subcritical crack growth measurements, the long-term strength is evaluated for marble. It was clarified that the long-term strength in water is lower than that in air in marble. It is concluded that water has a remarkable influence on subcritical crack growth in marble. It is also considered that the long-term stability of carbonate rock masses should be ensured in a dry environment.

Jan 1, 2015