Search Documents

By F. S. Hoseinian, M. Irannajad, M. Safari

In this study, the effect of chemical interactions of materials used in ion flotation on the removal of Ni(II) ions from low concentration synthetic wastewater was studied. Sodium dodecyl sulfate (SDS) and ethylhexadecyldimethylammonium bromide (EHDABr) as collectors and methyl isobutyl carbonyl (MIBC) and Dowfroth250 as frothers were used. To investigate the effective parameters and interactions of them, 16 experiments including 6 level variables were performed by supporting DX7 software and on the bases of 2-level factorial method. In the first step, the tests were conducted in a Hallimond tube. The result showed that collector of SDS and frother of Dowfroth 250 had appropriate interaction with each other at pH = 3. In the second step, optimal results from the first step were evaluated in a mechanical flotation cell. The removal of Ni(II) ions increased by increasing the time of flotation and they have a direct relation with the water removal. The kinetics study shows that the order and the rate of removal of the reaction do not follow any of the zero-order, first-order and second-order equations. The flotation rate curve on the removal of Ni(II) ions will divide the separation process to two stages, a fast flotation rate at the first stage and a slow flotation rate at the second stage. Ni(II) ions removal was obtained 88% at the best condition.This study showed that the use of ion flotation was a very effective method for Ni(II) ion removal from industrial wastewaters.

Jan 1, 2016

By J. J. Hussey

"Abstract-The ""Brunswick Horizon"" an informally named ore-bearing unit near the top of the Nepisiguit Falls Formation in the Ordovician Tetagouche Group, hosts the Brunswick No. 6 and No. 12 base-metal mines, as well as the former Austin Brook iron mine, in northern New Brunswick. Detailed structural analysis of the No. 6 and No.12 mines led to the prediction that a massive­ sulfide deposit may have been repeated by F1 folding along the Brunswick Horizon. A subsequent drilling program discovered the new massive-sulfide North End Zone at a vertical depth of 1100 m, 1 km north of the No. 12 underground workings. By the end of 1990, Zn-Pb-rich massive sulfides had been delineated over a strike length of 200 m and a down-dip extent of 170 m. Rock units intersected in the North End Zone are generally thinner and vary somewhat from those at the Brunswick No. 12 mine. Thinning of the hanging wall rocks may be primary, may result from attenuation along F2 folds, or may represent truncation by a thrust fault. The newly discovered sulfide zone indicates that significant potential exists for the discovery of other deposits at previously unexplored depths.SOMMAIRE-Dans le nord-est du Nouveau-Brunswick ""l'horizon Brunswick"" est le nom usuel de la zone qui contient les mines de métaux de base Brunswick No. 6 et No. 12, ainsi que l'ancienne mine de fer Austin Brook, toutes situées sur le dessus de la Formation ""Nepisiguit Falls"" dans le Groupe Tetagouche d'âge Ordovicien. Une analyse détaillée de la structure des mines No. 6 et No. 12 à permis a van Staal de prédire qu'un gîte de sulfures massifs pourrait se répéter dû à une déformation F1, au nord de Brunswick No. 12. Suite à un programme de forage, la nouvelle zone de sulfures massifs appelée le ""North End Zone"", profonde de 1100 rn, et à une distance d'un km au nord des chantiers souterrains, fut découverte vers la fin de l'année 1990, les sulfures massifs riches en Zn-Pb ont été délimités sur une longueur de 200 rn et une hauteur de 170 rn le long du pendage. Les unités de roches intersectées dans le ""North End Zone"" sont généralement plus minces et sont quelque peu différentes de celles de la mine Brunswick No. 12. L'amin­ cissement des roches pourrait être primaire ou être le résultat de l'atténuation le long des plis F2, ou soit tronqué par une faille. La nouvelle découverte d'une zone de sulfures indique un potentiel énorme pour la découverte d'autres g ""tes à ces profondeurs inexplorées."

Jan 1, 1992

By Xiaoxing Hu, Guibing Zheng, Yangge Zhu, Xingrong Zhang

"In China, more than 90 percent of titanium resources are reserved in vanadic titano-magnetite deposits. In this type of ore, the same elements such as Ti, Fe, Ca, Mg exist on surface of both ilmenite and titanaugite (the gangue mineral) because of isomorphism, which makes selective flotation difficult. Therefore, how to enlarge the floatability difference between these two minerals has always been a research emphasis and still needs to be studied further. In this paper, the pre-treatment methods using ultrasonic wave were proposed. The results indicate that ultrasonic treatment shows beneficial effect to enlarge the floatability difference, and the effect will be strengthened by extending the ultrasonic treatment time or increasing the ultrasonic power. The mechanism was investigated through infrared spectroscopic (FT-IR) analysis. Collector interacts with Ca and Mg which results in titanaugite flotation, after ultrasonic treatment, the dissolution of Ca and Mg is intensified, which leads to the lack of active points on mineral surface, so the floatability of titanaugite is depressed. Meanwhile, collector mainly interacts with Fe which results in ilmenite flotation, and the present of ultrasonic might promote its oxidation (Fe2+ to Fe3+), so the floatability of ilmenite after sonication is increased.INTRODUCTIONUltrasonic is the sound wave with frequency of 2 × 10-4 Hz~2 × 10-9Hz. Since the first International Symposium of Sonochemistry in 1986, the application of ultrasonic wave is more and more extensive. In researches about mining and metallurgy, various investigators have shown that intensive acoustic fields can modify the state of a mineral, leading to chemical or dispersive effects. Generally, the effect of ultrasonic vibration depends upon the nature of the mineral and also the way ultrasonic wave is applied (Celik, 1989; Ozkan, 2002). In addition, ultrasonic treatment usually plays roles of removal of reagents adsorbed layer from minerals and emulsification of flotation reagents when it is used in flotation (Nicol, Engel, & Teh, 1986; Slaczka, 1987; Djendova & Mehandj, 1992; Farmer, Collings, & Jameson, 2000; Gurpinar, Sonmez, & Bozkurt, 2004)."

Jan 1, 2016

By Terry McNulty

"Previous papers (McNulty 1998 and 2004) have dealt with the causes of successful and less successful achievement of design production rate by new processing plants in the minerals industry. Examination of many case histories has allowed the construction of curves or profiles that represent projects with similar characteristics that equate to differing degrees of care exercised during the project development phase. Simplistically, decreasing care is reflected by increasing risk and a heightened likelihood of poor technical and/or financial performance.This contribution provides an update, including recent case histories, and presents a modified Series 1A curve that includes the best 23 case histories, out of a total of 81 examined, or 28%. This is done to show that some very carefully developed and executed projects can ramp-up quickly and that owners of new projects should avoid being too pessimistic in projecting early cash flow if they are certain that they have done their homework. The role of metallurgical process development in the reduction of project risk is discussed and several financial analyses are presented that express the potential monetary value of a well-designed and professionally executed metallurgical program."

Jan 1, 2014

By Robert B. Parsons

"It is generally acknowledged that Canadian and foreign-based mining companies are spending relatively fewer dollars in Canada and more dollars abroad than was the case not many years ago. It is common to see the Canadian tax system being fingered as one of the causes in this shift in direction. However, if one takes the time to peel away the surface of our tax system, and to probe a little deeper into its substance, it will be found that the Canadian taxation of mining is generally quite competitive. IntroductionCross-border shopping in the mining industry? - Absolutely! Economics 100 teaches that dollars are votes in the capitalist system, and mining companies are going to cast their limited number of votes where they can achieve the highest return at the least risk. The Canadian consumer knows that taxes are a major factor in cross-border shopping, and mining company executives know that the same tenet holds true in their industry. Unfortunately, mining operations are subject to such a bewildering array of tax rules that making an intelligent decision is not always an easy matter.Statutory Tax RatesConsider, for example, the ""statutory"" tax rates shown in Table 1. (Statutory tax rate in this table refers to the simple sum of federal and provincial tax rates on profits as specified in the tax legislation.) Looking only at the total statutory tax rates (such as 66070 for Manitoba) , one might quickly observe that the Canadian mining industry is subject to a truly onerous tax regime, especially as compared to the United States where statutory tax rates can be in the 34% range."

Jan 1, 1992

By K. M. Ed

AN explosive is a solid or liquid substance which, when fired by some means, changes into a gaseous product occupying a volume very much greater than its original volume. The great speed at which this change takes place causes the explosive to exert a sudden blow on adjacent material. It is this action which is effective in blasting operations when the explosive, confined in a shot-hole, is fired. All explosives are similar in one respect, in that the change into the gaseous state is accompanied by the production of hot gases or flame. This results from the rapid combustion of the solid or liquid ingredients. Ex-plosives differ greatly, however, in the speed at which the reaction takes place. Black blasting powder, for instance, reacts comparatively slowly, hence the flame persists for an appreciable length of time. High explosives, on the other hand, react much more quickly; consequently, the flame is of much shorter duration. In 'closed-light' or 'gaseous' coal mines, the use of ordinary explosives is generally prohibited, due to their inherent ability to ignite gas or coal-dust by reason of the flame which they produce when fired. For instance, black blasting powder, which produces a flame of long duration, is not ordinarily considered safe to use in such mines; neither are ordinary dynamites, as their flames, while shorter than that of black blasting powder are, nevertheless, of sufficient temperature and duration to cause ignition of fire-damp or coal-dust. For this reason, specially formulated high explosives, called 'permitted' explosives, should invariably be used in such mines.

Jan 1, 1940

By K. Wongpreedee

Recovery and recrystallization of Au wire can degrade strength and alter conductivity properties during exposure to elevated temperature. Au Deformation Processed Metal Metal Composites (Au DMMC's) are being developed for electronic applications requiring high conductivity and high strength. This paper discusses the relationships between microstructure, strength, and resistivity of Au DMMC's. It also presents the results of a recent study on the elevated temperature stability of Au DMMC's of several compositions. Au-7 vol %Ag, Au-14 vol %Ag, and Au-vol 7%Pt DMMC samples were prepared by a powder metallurgy technique. All specimens were processed into wire by extrusion, swaging, and drawing. The smallest final diameter of these wires was 120 ?m. Thermal stability was analyzed by electrical resistivity measurements to determine the relation between transformation rates and time at elevated temperature. The extensive deformation used to produce these composites reshaped the initially equi-axed powder into filaments that are 30 to 100 nm in diameter and 16 to 180 mm in length. The small filament diameter confers high strength on the composite. The high conductivity can be explained by electrons flowing parallel to the filamentary microstructure aligned with the wire axis. Using the Avrami and Arrhenius equation relationships, it is possible to predict the times and temperatures needed to achieve various degrees of homogenization. The Au DMMC's were found to have good thermal stability compared to conventional coldworked Au interconnection wires. Although these composites will revert to solid solutions if exposed to high temperatures for prolonged time periods, their relative stability is sufficient to allow them to maintain their twophase microstructure during the anticipated lifetime temperature profiles of many products.

Oct 1, 2003

By Saeid Akhavan

Accumulative roll bonding (ARB) is a severe plastic deformation process for achieving ultrafine grains in metallic sheets without changing the sample dimensions. In this study, ARB process was carried out on 5083 aluminum alloy sheets up to 6 cycles. In this process, the surfaces of the strips to be joined are roughened and cleaned and then stacked. After stacking, the specimen is roll-bonded by rolling using a 50% reduction. The rolled specimen is cut into two halves, and the above-mentioned procedure is repeated for several times. Microstructural characterizations were analyzed by transmition electron microscopy (TEM). Tension and Vickers hardness tests were performed on produced sheets for evaluating their mechanical properties. In order to clarify the failure mode, fracture surfaces after tensile tests were observed by scanning electron microscopy (SEM). The results indicated that at the early stages of ARB process, grains were subdivided by deformation induced boundaries. After several ARB cycles, lamellar structure elongated in the rolling direction contains lamellar boundaries was formed. With increasing the strain, mean spacing of lamellar boundaries decreased. Finally, continuous recrystallization resulted in a microstructure covered with small recrystallized grains with an average diameter below 100 nm at the end of four cycle. The tensile strength and hardness of the 6 cycle ARB processed 5083 aluminum alloy sheet increased about two and three times of the initial values, respectively. Results indicated conformity between mechanical evolutions and microstructural changes during ARB process. Fracture surfaces observations showed that failure mode in ARB processed aluminum is shear ductile rupture with elongated small dimples.

Oct 1, 2011

By Saeid Akhavan

Accumulative roll bonding (ARB) is a severe plastic deformation process for achieving ultrafine grains in metallic sheets without changing the sample dimensions. In this study, ARB process was carried out on 5083 aluminum alloy sheets up to 6 cycles. In this process, the surfaces of the strips to be joined are roughened and cleaned and then stacked. After stacking, the specimen is roll-bonded by rolling using a 50% reduction. The rolled specimen is cut into two halves, and the above-mentioned procedure is repeated for several times. Microstructural characterizations were analyzed by transmition electron microscopy (TEM). Tension and Vickers hardness tests were performed on produced sheets for evaluating their mechanical properties. Moreover the texture parameter of the ARB-ed samples was calculated using their XRD patterns and the related equation. Additionally, the texture evolution during the ARB process was demonstrate by analyzing the measured pole figures and orientation distribution functions (ODF) and skeleton lines. The results indicated that at the early stages of ARB process, grains were subdivided by deformation induced boundaries. After several ARB cycles continuous recrystallization resulted in a microstructure covered with small recrystallized grains with an average diameter below 100 nm at the end of four cycle. Texture analysis revealed fiber textures have been discovered with continiuose of the ARB process cupper. Brass, S and dillamor textures identify which their differences are in intensity of ARB process. Results indicated conformity between mechanical evolutions and texture evolutions during ARB process.

Oct 1, 2011

By T. Purushotham, B. Samanta

ABSTRACT; The shaft bottom junction in a mine ventilation system is an important source of shock loss due to the combined effect of bend and area change. The occurrence of high-volume ?ow rates through this con?guration can potentially result in high energy losses. The current research examines the process of shock loss at a characteristic shaft bottom junction of an underground coal mine. Investigations are per-formed on both laboratory-scale models and three-dimensional computational ?uid dynamics (CFD) simulations, under both exhausting and forcing shaft bottom conditions. The effects of the plat roughness and the shaft bottom length on the shock loss factor values are also examined. The studies show that the combined effect of bend and area changes that occur at the shaft bottom junction results in shock loss factors that are much higher than those values resulting from abrupt area change only. The transition from a smooth wall condition to an unlined rough airway condition (relative roughness, e/d = 0.112) can increase the shock loss factors by 40%. The effect of shaft bottom length on the shock loss factor has not been clearly established due to con?icting results produced by scale model studies and the CFD simulations.

Jan 1, 2010

By A. M. Cormie

Introduction The purpose of this paper is to give a brief, general outline of mining practices at Torbrit Silver mine. The geology of the mine is touched on as it is felt that a rough picture of the geology will result in a clearer understanding of the mining methods employed. The main part of the paper deals with mining methods and a section is included on haulage. Development practice is mentioned only briefly. Torbrit Silver Mines, Limited, a subsidiary of Mining Corporation of Canada, is located in the Alice Arm area of northern British Columbia. Access to the mine is by boat to the village of Alice Arm at the head of Alice arm, then truck road, following the course of Kitsault river for 18 miles in a northerly direction to the plant site. The main portal is a further two-thirds of a mile along the course of the river, at approximately the same elevation as the plant, 1,014 feet above sea level. Geology The ore occurs in a massive, irregular-shaped quartz-barite body replacing a folded area in a series of volcanic breccias, tuffs, and flow rocks locally referred to as 'green-stones'. A series of parallel, nearly vertical, fine-grained basic dykes cut across the formation at right angles to the strike of the ore belt over a horizontal distance of 140 feet. The whole of the quartz-barite vein material, which ranges up to several hundred feet wide in places, carries silver values but commercial grade is confined to lenses and shoots where there have been more than usual concentrations of native silver and silver-bearing minerals. The ore-bearing structure plunges at approximately 25 degrees along an axis striking roughly N.65°W.

Jan 1, 1951

By J. P. Mogan, E. D. Dainty

Polynuclear aromatic hydrocarbon (PAH) levels were measured in underground mines in the vicinity of diesel vehicles equipped with several types of emission control hardware. In general, the emission control devices appeared to reduce PAH levels, but the companion mutagen study suggested that the reduction might not always be beneficial. All underground PAH concentrations were below the threshold at which a significant impact on health might be expected, but recent animal exposure studies have indicated that PAHs may not be the primary hazard from chronic diesel fume exposure.

Jan 1, 1994

By Jose Alberto Gonzalez, Said Sharif Mahboob, Jeffrey L. Shepherd

"During the industrial electrowinning of zinc, uneven growth can cause short-circuits and make the deposits more sensitive to the presence of impurities that can significantly impact current efficiency. To produce levelled zinc deposits, additives such as glue, licorice and sodium silicate are often added to the electrolyte. Even in the presence of additives, uneven zinc growth still takes place because of the combination of hydrodynamic and electrolysis conditions in the cell house. Recent advancements in imaging spectroscopy and scaling analysis have opened an avenue to further study the effects of additives on zinc growth morphology. In this study, Atomic Force Microscopy (AFM) and scaling analysis have been used to monitor zinc growth characteristics including roughness, periodicity, aspect ratios and growth mechanisms as a function of electrolyte composition as well as deposition time. Zinc was electrodeposited from an industrial electrolyte containing a host of additives onto an aluminum cathode with a platinum wire serving as the anode. AFM images of the samples were collected to obtain 3D topographical information on which scaling analysis was performed to extract details on root-mean-squared (rms) roughness, periodicity (grain size), aspect ratio of surface features and growth mechanism. This analysis provided information on the mechanism by which the previously mentioned variables can impact short term growth and also provided a prediction of expected growth at long deposition times.INTRODUCTIONElectrowinning is one of the final stages in the industrial production of zinc metal. It is during this process where dissolved zinc ions undergo electro-reduction from an acidic electrolyte onto an aluminum cathode and are later recovered by stripping the zinc metal from the substrate. However, due to the nature of zinc growth as well as the various operating conditions, zinc deposition may occur unevenly, sometimes causing short-circuits that can cause electrode damage and reduced zinc production."

Jan 1, 2016

By Brian O'Hearn, Doug Hanson

"The most commonly used tendon supports in the Sudbury area include rock bolts, rebars, friction anchors and cable bolts. Due to the fact that these tendons are physically different and employ different anchoring systems they offer varying degrees of stiffness, yield ability, load capacity, anchor dependability and energy absorption. These differences coupled with variable rock mass and changing stress conditions have made it challenging to engineer the design of an effective support system. By tapping into the knowledge and experience gained by ground control practitioners, an empirically based rating system has been assembled that offers a guide to designers of support systems when choosing the most effective tendon support over a range of rock mass and stress conditions.A methodology referred to as support planning can be used to design support systems whose rehabilitation costs will be minimized. The use of multiple tendon types in anyone support layout is advocated, particularly when the stress state of the rock mass to be supported is expected to undergo a change."

Jan 1, 1995

By A. F. Gregory

"AbstractA resumé of aerial radiation survey studies performed by and for Eldorado Mining and Refining, Limited, since 1943 is presented. Flight tests were initiated in 1947 and were followed .by intensified use and study of Geiger counters and other radiation detectors. Development of an aerial scintillation counter began in 1948, but •a sensitive large crystal unit was not available for exploration purposes until 1950. Modifications of this unit have been used in all subsequent surveys.For the Eldorado detector, several limiting conditions were established for successful radioactivity detection, the most important being that natural vein exposures can only be assuredly detected .at distances less than 150 feet. Sedimentary and pegmatitic radioactive occurrences can be detected at much greater distances. A helicopter investigation technique appears to •have •a useful prospecting potential.IntroductionAerial radiation surveys were first proposed in the early 1940's. However, it was not until 1949 that airborne detectors were extensively used in the search for radioactive minerals. Eldorado has flown about 50,000 miles of exploration flights, exclusive of tests, using a variety of •detectors and aircraft. Considerable data have •been gathered for .the evaluation of the several techniques employed. Much of the early work was performed with the co-operation of the National Research Council of Canada ( 1). More recent work was done in conjunction with the Commercial Products Division of Atomic Energy of Canada, Limited. The Development Department of this latter corporation designed and built the scintillation counter used in recent Eldorado surveys."

Jan 1, 1955

By T. Gerritsen, T. Plikas, K. Ochoa, M. Loveless, R. MacRosty, J. Reichart, R. Pula

Sidewall accretion in a smelting furnace plays an important role in furnace integrity as it provides protection to the sidewall cooling elements and thereby extends the furnace campaign life. The extreme thermal and mechanical stresses in the furnace and changes in the slag chemistry can cause the sidewall accretion to melt or break away decreasing the lining protecting the cooling elements. Thin accretion is highly undesirable as it increases the risk of exposing the cooling elements to the molten bath and in the worst case may lead to a failure. Therefore, monitoring the sidewall accretion on an operating furnace is extremely important to manage furnace integrity and to support safe furnace operation. Operators often generate estimates for sidewall accretion and refractory thickness using either copper cooler temperatures or heat load into the cooling water circuits. Multivariate statistical models, on the other hand, have the capability to consider all the process measurements simultaneously to provide a more reliable estimate. This paper describes the application of multivariate statistical models for sidewall integrity monitoring on a Flash Converting Furnace (FCF) and also discusses the online implementation of these models as the Sidewall Accretion Monitoring System. INTRODUCTION Rio Tinto’s Kennecott Utah Copper (KUC) smelter located near Salt Lake city, Utah operates a Flash Smelting Furnace (FSF) and a Flash Converting Furnace (FCF) to produce high-grade matte and blister copper respectively. Since the commissioning of smelter in 1995, several improvements were made to these furnaces to increase their efficiency and operational safety. At present, Kennecott smelter is known to be among the lowest-emission and highest energy recovery copper smelters in the world. Since the smelter start-up, Kennecott has invested in several advanced furnace monitoring practices to evaluate the integrity of the furnaces and improve their campaign life. An example is their temperature monitoring system installed for the smelting and converting furnaces, which continuously monitors the furnace sidewall temperatures and notifies the operators during temperature excursions. During an investigation on the converting furnace, it was revealed that there were frequent temperature excursions in the settler sidewall area towards the reaction shaft end of the furnace that caused significant furnace downtime. The reason for the sidewall temperature excursions was not clearly known.

Jan 1, 2019

By A. B. Morrow

Consulting engineers are well aware of large variations in plant operating cultures between countries, companies, and even within sites and operating crews. These operating cultures must be considered when designing Advanced Process Control (APC) applications in order to maximize utilization rates and return on investment. Designs must be driven by an understanding of the totality of unit operations. Economic factors, equipment constraints, management philosophy, maintenance department responsiveness, instrumentation reliability, operating crew skills and teamwork, and individual operator concerns are all important and must be considered during application design. A general approach to incorporating operating culture considerations into APC application design is described. A case study for an iron ore concentrator plant is presented.

Jan 1, 2014

Applications of proven real time, through-conveyor elemental analysis technology and benefits achieved will be discussed using case studies in base metals, iron ore and phosphate operations. PGNAA (Prompt Gamma Neutron Activation Analysis) technology and its background in minerals applications and applications which are expected to further improve its utilization will be reviewed. Short payback through operational benefits such as removal of waste from feed, increased feed grade and overall improved productivity will be demonstrated based on results achieved at several processing operations. PGNAA technology is most applicable to conveyed flows as it is unaffected by belt speed, particle size, segregation/layering, mineralogy or dust. As a transmission method able to penetrate in excess of 500mm of rock it provides extremely representative results continuously measuring through the full conveyed cross section and reporting results typically on one to five minute accumulated increments to the control room. Multi-elemental results and moisture content are used for active process control: diverting conveyed flow increments(bulk sorting), blending ore types in plant feed, and providing advance warning of significant quality changes to the downstream plant operators (e.g. flotation). Elements of interest may include deleterious components as well as target metals. Ore feed quality measurements are also useful in metal accounting, ore reconciliation and real time feedback to mining operations. Further benefits can result when combined with other technologies such as particle sorters, to upgrade diverted increments of subeconomic material to achieve higher feed grades and lower deleterious content to the main process. Measurement of elements (e.g. silica) which correlate with ore hardness or grinding characteristics can be used to moderate feed rate to grinding mills to prevent overload, hence optimizing grinding performance and reducing energy and grinding media consumption. Pebble flows can be analysed and uneconomic increments diverted to prevent recirculating flows consuming mill capacity unnecessarily. This also increases average feed grade.

Jan 1, 2016

By Wojciech Naworyta

The development of the Gubin lignite deposit, located in western Poland is the first mining investment of this magnitude in 30 years. Gubin is the second largest prospective lignite deposit in Poland, with over one billion tonnes of indicated reserves, which would be sufficient for a 2700 MW power plant for almost 50 years. The paper presents select problems related to the mining development of Gubin deposit. Attention has been paid to changes in legal and formal requirements for mining investments that were introduced after the change of Polish social and economic system. The significance of spatial, environmental and social conditionings has been emphasized. Typical attributes of the mine planning process have also been presented. Those include the long time horizon of the investment, uncertainty of external conditions and resulting difficulties in the project?s economic evaluation. Focus has been placed on mutual connections between particular elements of the project and time dependence during the process of their development. Iterative characteristics of the design process have been proven, together with resulting necessity of frequent verification of previous assumptions. As a background for presenting selected problems related to future development of Gubin lignite deposit, the methods of design have been discussed ? the variants method, the empirical method and the method of consecutive approximations. The tools and the possibilities of their use for solving specific problems related to mine design of an open pit have been broadly discussed. The chapter in which the authors relate to the specific problems of Gubin deposit development constitutes the main part of the paper. It depicts the assumptions on which the annual production and the total extraction of lignite during life-of-mine period have been based. The process of mine designing has been discussed, taking into consideration environmental, geotechnical, spatial, social and mining conditions. The criteria for choosing the location of the opening cut and the external dump have been mentioned. In the summary, the present state of mine design progress has been presented, together with some problems that will need to be solved during the next stages of the deposit?s development.

Aug 1, 2013

By Matej Petružálek, Tomáš Svitek, Tomáš Lokajícek

"Migmatite from the Skalka region (Czech Republic) was chosen as the experimental rock material. It has macroscopically visible plane parallel structure (foliation). The foliation was caused mainly by biotite grains arrangement. The cylindrical samples of migmatite with subhorizontal, subvertical and oblique foliation were uniaxially loaded up to the failure. Network of 8 broad band sensors was employed for acoustic emission monitoring and ultrasonic sounding. A grid search method with anisotropic velocity model was used for AE hypocenters localization. The source types of successfully localized events were determined from the average first arrival amplitude. Structural anisotropy of tested rock material caused the anisotropy of its mechanical properties (peak strength, Young’s modulus) as well as a different way of fracturing process in dependence on the angle between axial stress and foliation plane. The combination of splitting, shearing and sliding was found to control the fracturing of sample with subhorizontal foliation. The shearing and sliding was dominant in fracturing of samples with oblique foliation. With greater dip of foliation, the role of sliding increased at the expense of shearing. Due to the favorably oriented system of microcracks already present, the shearing and splitting was at the same level during fracturing of the sample with subvertical foliation before nucleation began.INTRODUCTIONThe process of failure of low porosity rocks depends on their mechanical properties and actual stress and temperature condition. At the low pressure and low temperature, the most common way is brittle failure, which is a progressive process requiring the initiation, growth and coalescence of cracks (Lockner, 1993). Stress strain behavior of low porosity crystalline rocks, during the laboratory compression experiments, is divided into four characteristic stages: crack closure, elastic region, stable crack growth and unstable crack growth which leads to the brittle failure, Brace et al. (1966) , Bieniawski (1967), Lajtai (1974), Cai et al. (2004), Nicksiar and Martin, 2012 and 2013.The fracturing process of stressed rock begins with the crack initiation (sci), which for low porosity rocks occurs approximately at 40-50% of peak strength (sp) (Cai et al., 2004; Nicksiar and Martin, 2013). After the sci, the dilatancy begins and stable crack growth follows up to the crack damage threshold (scd), which is approximately at 80% of sp (Cai et al., 2004). After crossing the crack damage level, there is an unstable crack growth accompanied with nucleation of fault plane (sn) at 97-100% of sp. (Rao et al., 2011). The stress drop accompanied with formation of macro scale shear failure plane follows after peak stress is crossed."

Jan 1, 2015