Search Documents

By Robert A. Creaser, Iain Mitchell, Robert L. Linnen

Abstract - The Bermuda Zn-Pb showing is hosted by dolomitized Blue Fiord Formation of Devonian age, located east of the Ensorcellement dome on the Grinnell Peninsula of Devon Island. Fluid inclusions in hydrothermal calcite indicate that the mineralization precipitated from low-temperature, highly saline brines. The ?34S compositions of sphalerite, galena, and marcasite range from 16.1‰ to 35.2‰. Consequently, the Bermuda showing is interpreted to be Mississippi Valley-type (MVT) mineralization. The apparent age of mineralization has been determined by the Rb-Sr method from sphalerite separates, and a Late Devonian age of 357 ± 50 Ma (MSWD=65), with an initial 87Sr/86Sr ratio of 0.7083 ± 0.0020 is indicated. This date, within error, is the same as the Polaris deposit. This suggests that the mineralization formed during the Ellesmerian Orogen, although it is also possible that mineralization is associated with extension, related to the opening of the Sverdrup basin. The strontium and sulfur isotopes and fluid inclusion analyses indicate the involvement of a brine that acquired its salinity from interaction with evaporites, lower in the stratigraphic succession. The Polaris mine is the type deposit in the Cornwallis Zn-Pb district and is hosted by the Thumb Mountain Formation. The results of this study are significant because they demonstrate that regional brine movement is more widespread than previously recognized, and that MVT mineralization in the Cornwallis Zn-Pb district is not restricted to the Thumb Mountain Formation.

Jan 1, 2004

By M. Saghaeian, R. Hejazi, Sheikhzadeh. V., A. Abazarpoor

"The morphology of iron ore concentrate particles is known to influence several properties of iron ore pellets, including drop number, compression strength, and reduction properties. This study aimed to determine why grinding methods and particle morphology influence green pellet properties. Particle morphology can be directly related to the grinding method: ball mill (BM) or high pressure grinding roll (HPGR). In this research, two iron ore concentrates, namely Gol-e-gohar and Ardakan, were ground by a BM and HPGR to produce a suitable Blaine value for pelletizing (nearly 1,900 cm2/g). Morphological features of particles were subsequently investigated by sieving and cyclone sizing for particle size distribution, the Brunauer-Emmett-Teller (BET) and Blaine methods for specific surface area (SSA) and scanning electron microscopy (SEM) for the evaluation of shape descriptors. It was concluded that HPGR resulted in generating a greater proportion of fine particles compared to ball milling. The BET results showed that the SSA of HPGR pellet feed was higher than that from the BM due to a greater proportion of cracks, indents and bulges and the creation of new fracture surfaces. SEM images processed by ImageJ software indicated that particles ground by the BM tended to be more rounded and less elongated than HPGR particles because of the breakage model of each method. To show the effect of morphology on the green pellet quality, green pelletizing was performed in a pilot pelletizing disc. The HPGR pellet feed had a higher drop number in comparison to the BM pellet feed, due to the angular and rough shape of the particles.INTRODUCTIONThe demand for fine or ultra-fine particles as feed material for ceramics, composite materials, and mineral processing is on the rise (Kotake, Kuboki, Kiya, & Kanda, 2011). The final concentrate of iron ore processing plants (filter cake) has a size range roughly between 0 and 300 µm, depending on the liberation of Fe containing particles (Meyer, 1980). In general, to produce a suitable pellet feed of appropriate quality, Blaine numbers of 1800–2000 cm2/g should be achieved (Van der meer, 2015)."

Jan 1, 2016

By G. Dodbiba, A. Otsuki, T. Fujita, J. Ponou, A. Shibayama

"The different types of nano to submicron particles, which are well-dispersed nano particles, coagulated nano particles or settled submicron particles, have been measured by the interactive force apparatus (IFA). The information is very useful for mineral processing treatment. The IFA can measure the particle size distribution in low to high concentration of particles in liquids and non-light transparent liquids. Here, mainly the emulsion and bubble size measurements are described.Emulsion (w/o type) is prepared with oil and water mixture. The nano to micro emulsion particle size is usually measured by light scattering method. The particle size distribution of emulsion of light oil measured by IFA agreed well with the one by the dynamic light scattering (DLS) method. The water size distribution in emulsions of gasoline is difficult for the small reflection index and C heavy oil is difficult for the black color by DLS method. The IFA can measure both emulsions.There are many methods to measure fine air bubbles, however, the finer nano size measurement apparatuses are DLS method and IFA. A “ghost” peak appeared in the large particle micron meter size in DLS method. The mean diameter in IFA is similar with DLS for the nano meter size. INTRODUCTIONParticle size distribution measurement of nano to submicron particle, emulsion and bubble size distribution are very useful for ultrafine particle separation and characterization of fine particles by the necessity of recent fine minerals separation (For example, Li et al.2016, Mikhlin et al.2016, Wang et al.2013). As for the size measurement of solid particles in liquids, three different types of nano to submicron particles, that are well-dispersed nano particles, coagulated nano particles or settled submicron particles, have been measured by the interactive force apparatus (IFA). The particle size distributions are compared with the one of dried particles measured by TEM or SEM. The well-dispersed nano particle size distribution by IFA is influenced by the nano size surfactant micelles and becomes smaller, when compared with the TEM result. The size distribution of nano size of magnetite particles in water is influenced by the isoelectric point and the mean diameter of coagulation becomes larger. The particle coagulation in diluted suspension is about 2nm smaller when compared with the higher concentration. The submicron nickel particle size distribution is well agreed the result by SEM. The coagulation effect is small in the submicron size of nickel powder in water (Fujita et al., 2013). In this paper, the emulsion and bubble size measurements are mainly described."

Jan 1, 2016

By Robert B. Parsons

"In this period of improved metal prices and reported profits, valuable lessons should be recalled from the 1970s when a similar cycle lured the federal and provincial governments into thinking that they could grab bigger pieces of the pie without harming the minerals industry. It took years for the industry to recover from the damage inflicted by that unprecedented scramble for higher tax revenues. It is hoped that the current policy makers will have learned from the lessons of the seventies, and will realize that mining companies need to keep a reasonable share of profits realized during the good years in order to prepare for the inevitable downturn in the cycle.INTRODUCTION"", «. We have made clear to industry that super profits... will no longer be tolerated "".With that assertion, the Honourable David Barrett , Premier and Minister of Finance of the Province of British Columbia, announced the introduction of a new mining tax regime in his February 17, 1974 bud get papers . British Columbia producers would face a basic royalty and a royalty on so-called ""super profits"", resulting in some instances in tax rates exceeding 100070 of pre-tax profits.The ball started to roll. Mining tax changes knew no political or geo graphical boundary. On April 9, 1974, Ontario's Treasurer John White stated in his budget speech:""Increased demand by major industrialized countries has resulted in sharply higher metals prices and substantial wind fall gains for the mining industry in Ontario. With the prospective demand for minerals likely to sustain current price trends into the future, it is only fair that we secure for the people a higher return from our natural resources""."

Jan 1, 1989

By Charles Camsell

If it were necessary to preface a discussion of the mineral position of the Empire by justifying one's interest in that subject, there are two points that at once suggest themselves by way of vindication. Tremendous Growth of MINERAL Consumption The first of these points has to do with the general question of the world's mineral consumption. Most thinking persons appreciate in a more or less vague way the vital rôle that has been, and is being, played by mineral products in building up the material side of our modern civilization. But, apart from that casual and almost subconscious appreciation, very few have any precise knowledge of the extent to which the growth and the operation of our vast present-day industrial structure has been made possible by, and only by, a tremendous increase in the consumption of mineral products of all kinds. The increasing use of minerals confronts us today at almost every turn. It does not matter in what direction we look-at the expansion and the change in transportation facilities, in the air as well as on land and on sea; at the increasing mechanization, not only in factory and mill but even in our domestic life; or at the constantly widening use of machinery for all phases of farm production-everywhere we meet the same phenomena of rapidly growing uses of equipment produced mainly from minerals. Without resorting to any tiresome statistics, a few figures may suffice to indicate with what enormous strides the world's mineral consumption has been advancing. The figures for recent years may be open to objection on the plea that, ever since the outbreak of the world war, conditions have hardly been sufficiently normal to give us trustworthy data-we have been living under extremes either of depression or of abnormal stimulation. During the last decade before the war, however, from 1903 to 1913, the world was moving along in a quietly prosperous manner; and we have figures, or at least reasonably reliable estimates, as to the growth in mineral consumption during that decade.

Jan 1, 1932

By N. Geoffroy, E. Benguerel, G. P. Demopoulos

In the late 1990s, a chemical process to remove mercury and selenium from weak sulphuric acid solutions was patented and implemented in the CEZinc refinery in Valleyfield, Quebec. The CEZinc process comprises two stages. In the first one, sodium sulphide is added to the weak acid solution in order to precipitate the soluble mercury. The solution is then treated with sodium dithionite in order to reduce the selenium to elemental form. Because of recent changes in the composition of the industrial solution, a project to study the background chemical reactions was started. In this paper, a review of the background chemistry is presented on the basis of several eh-pH diagrams on one hand, while on the other experimental results are reported dealing with the reaction of selenium (IV) species with either dithionite, sulphide or a combination of the two. According to this work, elemental selenium enjoys a wide pH-eh range stability with selenium sulphide being metastable. Selenium (IV) in single metal synthetic solutions was found to be reduced - to elemental state - at ambient temperature down to ppb range with dithionite as long as the stoichiometric ratio (dithionite/selenium) was in excess of two and the pH < 1.7. Under these conditions the reaction was very fast reaching completion within one minute. Sodium sulphide proved equally effective in reducing selenium (this time as selenium sulphide) to ppb range from single metal solutions. However, in mixed Se-Hg solutions deviations from this "ideal" behaviour was observed resulting in higher levels of residual soluble selenium left in solution.

Jan 1, 2008

Fiabilité Totale d?Usine (FTU) Plan de la présentation ?Théorie de l?entretien ?Analyse comparative juin 2005 ?Session de travail 2005-2006 ?Suiviet Résultats(IndicateursdePerformance)

Feb 1, 2008

By T. Nomura, N. Saitoh, K. Tamaoki, Y. Konishi

We have developed new recycling technologies, based upon an eco-friendly biotechnology, in order to extract precious and rare metals sourced from end-of-life products and electronics. We have been focusing on the metal ion-reducing bacteria, Shewanella algae and Shewanella oneidensis, that are able to reduce and deposit gold ions (Au(III)) or PGMs ions (Pd(II), Pt(IV) and Rh(III)) into metal nanoparticles at room temperature within 120 min. When processing the aqua regia leachate of printed circuit boards, Shewanella bacteria were able to rapidly and selectively collect gold ions under acidic conditions in the presence of heavy metal ions, proposing a new bio-recovery system for gold. This biotechnological procedure also has the potential to allow the recovery of PGMs from the leachate of automotive catalysts. Shewanella bacteria were also able to successfully perform the complete reduction and deposition of the PGM ions. The ability to collect the PGM ions suggests that this represents a new process for the biorecovery of PGMs from used automotive catalysts. Our proposed biological method enables the rapid and highly efficient recovery of precious and rare metals via separation and concentration utilizing microbial reactions at room temperature.

Jan 1, 2014

By R. Argane

In this work we assessed the geochemical behavior of concentrator tailings deposited at the abandoned mines of Zeida and Mibladen (Upper Moulouya, Morocco), using physico-chemical analyses, mineralogical characterization, acid base accounting and weathering cell tests. The aim of the study was to evaluate mine drainage quality and to assess metal mobility from these concentrator tailings. Chemical analyses show that the Upper-Moulouya abandoned tailings contain relatively high quantities of lead (0.261 to 0.594 % wt). Mineralogical analyses reveal the abundance of neutralizing minerals (calcite, dolomite, ankerite, and aluminosilicates) which influence mine drainage and metal mobility in mine tailings. Leachate analyses from weathering cell tests show alkaline conditions, small conductivity values, and low solubility of Pb-mineral phases. According to these results, abandoned mine tailings in the Upper-Moulouya district have very low potential for generation of contaminated mine drainage and for leaching of heavy metals. However, the inhalation of tailings exposed to winds generate dust problem facing the local population and may cause health consequences.

Aug 1, 2013

By R. St. C., G. E. Morris, M. Zbik, Smart

Effective flocculation and dewatering of slurry streams containing clays (particularly kaolin and smectites which are often <200nm in lateral dimension) is becoming increasingly urgent. Release of water (often >75 wt%), for recycle and reduced make-up water consumption, from slurries in tailings streams and dam beds is usually slow and incomplete. Changes in settling rates and solids density of tailings containing clays can be achieved in practice by changes in pH, dissolved cations and flocculant additions. To achieve fast separation of clays from water and minimization of retained water, individual particles need to be bound in the initial stages of thickening into large, high-density aggregates, which may sediment more rapidly with lower intra-aggregate water content. Quantitative STIMAN (STructural IMage ANalysis) cryo-SEM imaging, shows that the structure of aggregates formed before flocculant addition has a determinative effect on these outcomes. Without flocculant addition, 4 stages occur in the mechanism of primary dewatering of kaolinite: initially separate particles and aggregates are dispersed (<0.3GP, where GP is the gel point); a partially-gelled chain network then forms linking particles edge-edge (EE) still well below the OP but remains largely suspended; after an induction time, this network structure rearranges from EE to face-face (FF) contacts densifying, compacting and dewatering the aggregates with settling rates well above Stoke&apos;s Law estimates for >20µm particles or aggregates; the GP is rapidly reached during settling producing a network spanning the vessel with compressive strength. This sponge-like structure with EE oriented particles limits slurry dewatering because the steric effect in the resulting partially-gelled structure is much more dominant than the electrostatic effects predicted by DLVO theory. Van der Waal&apos;s forces at very close distances, as particles slide across each other, may be responsible for the EE to FF change in structure. In this way, the previously extended network contracts, and when the solid volume fraction is low, the continuous network breaks apart forming aggregates and aggregate associations as flocs which arc able to freely settle. These densified aggregates settle at increased rate, give lower bed density and retain less water after drainage. With flocculant addition, the internal structure and networking of the pre-aggregates is largely preserved but they are rapidly and effectively bound together by the bridging action of the flocculant(s). The STIMAN analysis shows that there is a inverse correlation of intra-aggregate porosity (and void permeability) with Darcian permeability (and extent of dewatering) whereas there is a strong positive correlation of Darcian inter-aggregate permeability with settling and primary dewatering rate.

Jan 1, 2004

By Hammenm R., J. Hammen, C. Hammen

"The production of salable Rare Earth Element (REE) products necessitates a sequence of chemical separation steps between the mine and market commodities. The effectiveness of the chemical separations that purify REE salts is critical to the success of the producer, as the purity of REE salt products affects their market price. This is due to the fact that impurities in REE salts, even at low levels, can be deleterious to the function and usability of the end product. The purification of REE by removal of low levels of contaminant has been referred to as "product polishing". The technologies commonly in use for product polishing, solvent extraction (SX) and ion exchange (IEX) are challenged by the availability of separation chemistries to separate the contaminant from the desired REE salt. In simple terms, if a product specification is 99.9% purity, the SX or IEX separation reagents need to have at least a 999:1 selectivity ratio. Significant testing has been carried out on the use of solid phase extraction (SPE) columns to extract low-level impurities such as aluminum or zinc from REE product streams. The SPE columns are nano-composite materials that have rapid equilibration kinetics with the solutes being processed by the columns. The SPE matrices have been modified with chelating ion exchange ligands that bind the contaminating ion with great selectivity in residence times of a few seconds. Thus, REE streams with 1 to 2% of contaminating aluminum ions, have been polished to >99.99% purity. In this paper, results are presented on the removal of aluminum impurity from a didymium (neodymium+praseodymium) product stream using SPE technology. The selection of the SPE medium and the process steps to treat the feed solution for aluminum removal and ultimate stripping and recycle of the solid phase extractant are discussed."

Jan 1, 2014

By A. V. Tarasov

There are still a number of copper smelters in the world using the roasting and smelting process flow diagram for treating sulphide raw materials. The technical, economic and environmental performance indicators of such operations are inferior to the respective indicators of advanced processes. First of all with respect to copper and sulphur recovery: 95% and 75% as compared with 98% and over 90%, respectively. Based on the studies of the single-stage smelting process to produce white metal and blister copper conducted during recent years an analysis of the feasibility of roastingsmelting technology improvement was carried out in the Gintsvetmet Institute to substantially increase the copper and sulphur recoveries. On the basis of this analysis, it was proposed to modernize the technology and equipment within the framework of the existing process flow-sheet. The proposed modernization implies an increase in the roasting temperature; higher desulphurization degree in the process of roasting; a number of modifications in the roaster design depending on the particular conditions of a given operation; addition of lime flux to the feed charge to roasting; and transition to combined calcium-silicate smelting slags. The metallurgical and energy computations made have indicated that the proposed modifications of the technology will improve the copper and sulphur recovery up to 98% and 90%, respectively. The required capital investments have been estimated using as an example a particular copper smelter, the payback period determined taking into consideration additional output, fuel saving and a reduction in fines for sulphur emissions. For comparison, the capital cost of a smelter modernization is given for change-over to basically new autogenous Ausmelt, Outokumpu and V anyukov smelting technologies.

Jan 1, 2007

By Robert B. Parsons

"Income tax legislation is not keeping pace with federal and provincial environmental legislation. There is a vast array of new environmental regulations at various stages of implementation across the country. Unfortunately, there are serious concerns about the deductibility of significant payments which mining companies will be required to make under these new rules, and the Department of Finance seems to be reluctant to act on these concerns. IntroductionWhile the federal and provincial governments are racing ahead with obvious fervour to introduce new envirorunental laws, the tax rules relating to envirorunental costs are being allowed to lag far behind. In a nutshell, the tax treatment of envirorunental costs is not keeping pace with the new envirorunental legislation.One of the most serious concerns of the mining industry is the deductibility of mine reclamation or closing costs. The producing provinces are well advanced down the road toward mandating upfront deposits, bonds, or similar financial guarantees to protect the envirorunent from the operation and eventual closure of a mine. These requirements are not small. In some instances, they can amount to tens of millions of dollars. And, if there is no tax deduction for these sums when they are set aside by the mining company, then the costs have to be paid out of the company&apos;s after-tax earnings."

Jan 1, 1991

By A. Alfantazi, L. Choudhary

Gold leaching in thiosulfate solution has attracted widespread research interest through the last two decades primarily due to its perceived environmental benefits in comparison to the conventional gold cyanidation technique. However, the data on the corrosion and/or corrosion-induced failures of plant infrastructure materials in the solutions relevant to thiosulfate gold leaching are very limited. Accordingly, this study aims to characterize the electrochemical corrosion behavior of stainless steel 316L in the thiosulfate gold leaching solutions. Electrochemical corrosion response was investigated using potentiodynamic polarization and electrochemical impedance spectroscopy. The morphology of corroded specimens was analyzed using scanning electron microscopy.

Jan 1, 2014

By Mohsen Mohammadi, Edward Cyr

"To date, several studies have been performed on the static mechanical properties of SLM-AlSi10Mg alloy. There have also been more recent studies on the relation between scan strategy, texture, and mechanical properties of SLM metals and composites. However, there is a huge knowledge gap in the available literature regarding texture and mechanical behavior of SLM-AlSi10Mg alloy under high strain rates. Therefore, in this study, dynamic mechanical behavior of AlSi10Mg_200C alloy manufactured by DMLS technique was investigated at high strain rates ranging from 900/s to 1700/s using Split Hopkinson Pressure Bar. Texture using X-ray diffraction technique of the initial samples were measured. The yield strength, peak flow stress, and ductility increased in all samples with increase of strain rate. TEM studies have also revealed evidence of continuous dynamic recrystallization in grains after 900/s–1700/s strain-rate tests. A Taylor polycrystal crystal plasticity constitutive model was then developed to capture and predict the texture evolution and mechanical response under dynamic loading, using plastic work as a critical parameter for the onset of recrystallization.INTRODUCTION Additive manufacturing (AM) powder techniques are among the fastest advancing breakthroughs in manufacturing in recent years, defined by a bottom-up layer by layer process of joining with energy input from lasers or electron beam (Herzog et al., 2016; Gibson et al., 2015). Among alloys fabricated by SLM, AlSi10Mg is of high interest to industry and academia due to its low density, high specific strength and excellent corrosion resistance, making this alloy a viable contender for aerospace, automotive, and marine applications. Circumstances such as car crash or bird aircraft strike hazards subject potential additively manufactured AlSi10Mg parts to impact loadings. This drives an interest in understanding and predicting dynamic behaviour of these alloys. AlSi10Mg is the AM counterpart of A360 die-cast aluminum, which possess hypoeutectic microstructure (Li et al., 2015). Up to the present time, many studies have presented the mechanical properties of SLM-AlSi10Mg alloy. The mechanical properties and microstructure of AlSi10Mg produced by selective laser melting (SLM) or DMLS techniques can be controlled using different parameters, such as feedstock powder (Asgari et al., 2017), and process parameters (Olakanmi et al., 2015). The microstructure and mechanical properties of AlSi10Mg can also be controlled using post heat treatment after SLM process Li et al., 2016). The mechanical properties of SLM-AlSi10Mg are sensitive to strain rate and can both change under quasi-static (Rosenthal et al., 2017) and high strain rates (Asgari et al., 2018). However, a significant knowledge gap in available literature regarding modeling these behaviours, and especially micromechanical modeling of dynamic behaviour."

Jan 1, 2018

By N. W. Martison, J. E. Hawley

"The Moulton Hill deposit is in the Eastern Townships of Quebec, 3 miles northeast of Sherbrooke. It is complex, both structurally and mineralogically, consisting of a narrow, irregular, mineralized zone that has been traced for a length of 600 feet, and in places to a depth of 1,000 feet, containing copper, lead, and zinc sulphides with a low content of gold and silver. It lies in a series of highly schistose micaceous rocks, believed to be of Ordovician age, but the mineralization is probably post-Lower Devonian. New details of the structure of the ore have become available since it was first described (1) , and as these show some striking peculiarities a further discussion is here merited .As detailed elsewhere, the deposit was discovered in 1942 as a result of regional geological studies followed by the application of electrical geophysical methods.Actual production began in July, 1944, and ceased in June, 1945. During the period July, 1944 to June, 1945, 75,643 tons were milled§, yielding the following:"

Jan 1, 1954

By W. Lamb

Feed Preparation ? Five primary parameters affect the screening efficiency ? Ore characteristics ? Operational characteristics ? Screen characteristics ? Water addition and washing ? System design

Apr 1, 2005

By C R. Evans

Whole-rock and muscovite potassium-argon dates from selected low-grade metamorphic rocks of Precambrian age in the Canadian Rocky Mountains near Jasper, Alberta, were obtained to ascertain the age of the source terrain and the age of the metamorphism. Ten argillites gave whole-rock dates ranging from 270 to 485 million years, dates which are apparently inter-mediate between the age of the source material and that of the metamorphism. "Up-dating" increases with the degree of orientation of muscovite in the cleavage plane, and with the ratio of the muscovite in the cleavage plane to that in the plane of the bedding. Detrital muscovite from four arenaceous rocks gave dates ranging from 1,050 to 1,780 million years. "Updating" increases with decreasing grain size, so that, within the range investigated, the cube of the median diameter (¢) of the muscovite is apparently proportional to the radiometric date.

Jan 1, 1964

By D. R. Hatton

To obtain sufficient material on which to perform copper-molybdenum separation testwork a variability set of drill hole reject samples amounting to several tons was put together to include the different ore types proportions expected in the copper circuit. The samples were treated in a copper circuit pilot plant and enough mass of bulk concentrate was recovered to conduct copper moly separation tests in the laboratory. Tests consisted of stage flotation reactor (SFR) rougher pilot plant tests, conventional laboratory rougher, cleaner and 4 stage open circuit cleaner tests. The mineralogical liberation analysis of the feed and concentrate was used to model the effect of liberation on the grade-recovery relationship of the different samples. Mineral kinetic parameters for the various samples were determined by calibration to the test data. The copper concentrate results as simulated from previous studies on the same deposit were used to simulate the variability in head grade and throughput expected for the feed to the copper molybdenum separation circuit for each of the first 10 years of production. This variation in feed was then simulated through the separation circuit to obtain optimised molybdenum grade recovery curves to forecast the circuit production for each of the first 10 years. INTRODUCTION Incorporating Geometallurgy into the design for a copper molybdenum separation is especially challenging due to the low mass of final concentrate typically produced during testwork. This is due to the low molybdenum head grades and high overall molybdenum upgrading expected. With molybdenum head grades of around 300 ppm, 1 tonne of copper circuit feed is expected to produce around 300 g of molybdenum concentrate in the plant. In the laboratory however, this may end up only resulting in a few grams. Obtaining sufficient mass for laboratory testing therefore requires starting with a large initial sample and careful testwork planning to maximise the utilisation of this mass. A testwork program was designed to investigate the effect of ore variability on the copper molybdenum separation circuit (here after referred to as the molybdenum circuit). Composite samples were selected to represent the various ore types, copper content, moly content, pyrite content and clay contents expected in the copper circuit feed. These samples were run through a bulk copper pilot plant to create the feed for the molybdenum testwork. The molybdenum testwork consisted of rougher kinetic flotation tests, rougher cleaner kinetic tests, rougher cleaner kinetic tests with regrind, stage flotation reactor (SFR) pilot plant tests, open circuit cleaner tests. These tests were used to calibrate the ore kinetics in the IGS-FLEET model for simulation of the molybdenum circuit performance.

Jan 1, 2019

By Marko Lampi, Ross Andrews, Jouni Pihlasalo, Robert Matusewicz

With widespread discussion on reducing carbon, sulphur and other emissions, use of sustainable energy sources and the pivotal circular economy theme, consideration needs to be given to pyrometallurgical operations broadly and more specifically, non-ferrous metallurgy. These themes present a number of challenges in terms of current operations and the view of processing the metals which are largely taken for granted in day to day living. This paper considers how these themes will impact pyrometallurgical flowsheets using the non-ferrous base metals as an example. It will examine the flowsheet chain to offer views on the boundaries of flowsheet optimization and the application of available tools to meet these future goals and challenges. INTRODUCTION The themes of reducing footprint through lowered CO2, S and other emissions, together with process sustainability (e.g. lowered energy) and links to the circular economy are well known to everyone in the metals industries. Whether it is reducing greenhouse gas emissions or analysing the importance of metals recycling in the circular economy, all these themes carry with them the fundamental premise of any change being considered; how can you best optimize a system to meet your aims? Of course, this depends on the available tools and the approach used for optimisation.

Jan 1, 2019