Search Documents

By James D. Bliss, David M. Sutphin

"On the basis of differences derived from genetic, descriptive, and grade-tonnage data, graphite deposits are classified here into three deposit types: disseminated flake, amorphous (microcrystalline), or graphite veins. Descriptive models have been constructed for each of these deposit types, and grade-tonnage models are constructed for disseminated flake and amorphous deposit types. Grade and tonnage data are used also to construct grade-tonnage models that assist in predicting the size and grade of undiscovered graphite deposits. The median tonnage and carbon grade of disseminated flake deposits are 240 000 tonnes and 9% carbon and for amorphous deposits, 130 000 tonnes and 40% carbon. The differences in grade between disseminated flake and amorphous deposit types are statistically significant, whereas the differences in amount of contained carbon are not .IntroductionIndustrial minerals, including mineral construction materials such as sand, gravel, and crushed stone, have historically exceeded metals in global production value. Today, industrial minerals are being used in new and sophisticated ways in response to the late 1980s emerging information- and service-based economies' requirements for less metal and more industrial minerals . Natural graphite is an example of one such mine ral that has been known since ancient times, and is now finding new applications. Graphite was first used as an industrial mineral in Bavaria in 1400 A.D. where it was an important component of crucibles. Traditionally, natural graphite has been used in heavy industries. New applications, such as development of carbon-magnesite bricks a decade ago and the current advancement of alumina/graphite refractories, are increasing its graphite use. Other new uses for natural graphite, such as the use of graphite powder as a thermal blanket for the continuous casting o f steel (Northern Miner, 1987) and the addition of expanded graphite to polyurethane foam where it acts as a flame retardant (Industrial Minerals, 1987), are increasing the demand for this mineral. To meet future demand for graphite and other industrial minerals, knowledge of the characteristics of the deposit types in which they are found is important. A further look at the deposit types for graphite and at construction of descriptive and grade-tonnage models is warranted .The graphite industry recognizes three basic types of graphite , distinguished primarily on the basis of grain size: crystalline flake, lump and chip, and amorphous. These naturally occurring forms of graphite are products of metamorphism and are found in schists of various types, gneisses, and marbles. Temperatures of at [east 400°C are thought to be required for graphite formation (Landis, 1971). Synthetic graphite, also known as artificial or manufactured graphite, is a man-made carbon product and offers higher purity and lower crystallinity than natural graphite. Several authors have written about graphite's unique physical and chemical properties and the uses for individual types of graphite (Krauss et 01., 1988; Graffin, 1983; and Harben and Bate s, 1984)."

Jan 1, 1990

By A. J. Keen

"Cominco's Polaris Mine is an underground lead/zinc operation located on Little Cornwallis Island in the Canadian High Arctic. Polaris is the world's most northerly base metal mine, situated at about latitude 75°N and longitude 97°W (Fig. 1). The closest community is Resolute Bay about 100 km to the southeast.During the construction and development phase Cominco adopted a unique scheme to save time and money. Many facilities including concentrator, powerhouse, shops and warehouse were built on a barge in southern Canada. The barge was towed 4800 km to the site in August 1981. Production at Polaris began in November 1981. The current mining rate is 1 million tonnes per year. The mine employs 250 people with about 190 on site at any time.GeologyThe deposit is a Mississippi Valley type orebody and lies near the top of the Ordovician Thumb Mountain Formation. Ore minerals consist of sphalerite and galena with the gangue being predominantly dolomite with calcite and marcasite. The orebody is situated completely within permafrost, consequently the voids frequently found in the ore are filled with ice. The orebody strikes north-south, dips approximately twenty degrees to the east and takes up an area about 400 m wide by 700 m long. The upper portion of the orebody (60 m to 150 m below surface) lies in an area called the Panhandle Zone. The deeper portion of the orebody known as the Keel Zone extends to 300 m below surface (Fig. 2). The deposit is strongly zoned with a high grade zinc/lead and iron-rich tabular core overlain and underlain by vein, stringer and breccia mineralization. The ore reserves at January 1991 were 14.6 million tonnes at 3.6% Pb, 13.7% Zn, 3.2% Fe, after producing 8 million tonnes at 3.9% Pb and 14.2% Zn since November 1981"

Jan 1, 1992

By Charles G. Kemsley

IN January, 1939, Dome Mines, Limited, purchased a few bars of an alloy drill-steel for the purpose of testing its fatigue resisting qualities as compared with those of a straight carbon-steel then in general use at the mine. A steel of the following analysis was selected: Carbon 1.00% Sulphur 0.022 Chromium 1.26 Silicon 0.17% Phosphorus 0.028 Vanadium 0.1 Manganese 0.32% Molybdenum 0.30 This steel has a tensile strength of 180,000 lb. per square inch and a Brinell hardness of 380, as compared with a tensile strength of 114,000 lb. per square inch and a Brinell hardness of 230 for the standard carbon drill steels, in the as rolled' condition. The result of this test showed that about five times as many runs could be obtained from the alloy steel before failure from fatigue. It was therefore decided to replace gradually the one-inch quarter-octagon carbon steel, then in use, with seven-eighths quarter-octagon alloy steel. In January, 1940, six machines was placed on the seven-eighths steel and this was gradually increased until now (March 15th, 1941) fifty per cent of the steel being used is alloy steel. An O'Donovan furnace is used at the Dome for heat-treating their carbon drill-steel. In this furnace, a magnet withdraws the steel when the critical temperature has been reached, and the operator then places the steel in the quenching tank. Not being able to use this furnace for the alloy steel, the management felt that some means should be developed to determine the quenching temperature without depending upon the operator's judgment of the correct 'colour'. With the assistance of the Canadian General Electric Company, a radiation-type vacuum thermocouple pyrometer was adapted to this purpose, with excellent results; in fact, with this instrument no previous experience in hardening is necessary and results are remarkably uniform.

Jan 1, 1941

?Founded in 1969 by the Ruia family ?Diversified global business corporation with a balanced portfolio of assets in the manufacturing and service sectors; $15 Billion revenue in FY 2009-2010 ?Employs 70,000 people worldwide with offices in Asia, Africa, Europe and North America

May 1, 2011

By Wang Wenqian, George W. Poling

"Devices and flowsheets for recovering fine placer gold are reviewed. Inefficiencies of gravity processing techniques are documented and discussed. Prospects of combining gravity and froth flotation techniques are presented. Possibilities of using other separation techniques, such as magnetic and electrostatic devices are also discussed.IntroductionSeveral new methods for beneficiating different types of placer ores have been developed in the last two decades. Improved efficiencies in the recovery of fine particles have been achieved by improving gravity flowsheets and machines as well as by developing multiple treatment techniques involving flotation, magnetic and electrostatic separations. Placer gold processing, however, has been an exception to some extent. Gravity concentration using riffled sluices accompanied by mercury amalgamation is still the main method in use today. Because of this, the recoveries of fine gold and the other associated values are often similar to those achieved several decades ago. For example, very few sluice systems recover significant placer gold finer than 100µm in size.Only a few proposals for using alternatives to simple gravity methods for recovering fine placer gold can be found in the published literature. The fixed, low gold price discouraged research in this field for many years. Development of more efficient processes has not kept pace with the recent rapid escalation in the price of gold. Froth flotation for saving fine placer gold might now prove economic, for example. This paper reviews literature published on the recovery of fine placer gold over the period 1907 to 1980. Suggestions for improving the performance in this field, based on the authors' current testwork, are also presented."

Jan 1, 1983

By Desmond M. Levins, Reginald K. Ryan

"Removal of radium from uranium tailings would substantially lessen their environmental impact because it would eliminate, or greatly reduce, the hazards arising from radon emanation, leaching of radium, dust dispersal and gamma radiation. A process is described to extract radium from tailings by leaching in 3M Nael solution. The radium can be rapidly leached at ambient temperatures by either multi-stage contact in agitated vessels or washing on a tailings filter cake. Extraction efficiencies ranging from 80 to 94% have been measured for tailings derived from a number of Australian ores.Methods for radium recovery from the leach solution by precipitation, ion exchange and adsorption have been examined. Precipitation as barium/radium sulphate appears to be the most suitable approach. A possible flow diagram for the process is proposed which involves recycle of the saline leach liquor.IntroductionDisposal of mill tailings is the most contentious environmental issue facing the uranium mining industry. The conventional approach to managing tailings is to store them in a dam above ground. Attempts have been made to stabilize some tailings piles by physical or chemical methods. In a few cases, the tailings have been covered with earth and revegetated. However, most tailings piles from abandoned mills are in a neglected state and subject to the erosive and dispersive forces of nature. The cost of remedial action is high. The United States Department of Energy (DOE) has estimated that it will cost up to $130 million to rehabilitate abandoned mill sites in the U.S .A..Environmental authorities are now insisting that uranium mining companies improve their methods of tailings disposal. In the United States, the preferred approach is burial, either in mines or in specially excavated pits. Tailings retention systems as operated in Canada are regarded as storage facilities until an acceptable method of disposal is found. In Australia, the Fox Commission recommended that tailings from the Ranger project should be returned to the open-cut mine. Returning tailings to the mine has considerable merit, but it is not always a viable option. In many underground operations, it is not physically possible to fit all the tailings in the worked-out mine. In other cases, the groundwater hydrology of the mine may be unfavourable."

Jan 1, 1980

By V. K. Karra

"A simplistic algorithm jar simulating the rod or ball mill Bond grindability test applied to ores and minerals is presented. A performance comparison between the present algorithm and a previously published algorithm by Kapurot, modified in this work jar a fair evaluation, is also given. A worked example is furnished jar leading the reader through the various calculations.IntroductionThe Bond grindability test is widely used for the prediction of the power requirement of an industrial grinding mill. The procedures for conducting this test in either a ball or a rod mill are available(1). In the case of a ball mill, batch grind abilities have been correlated to Bond grindabilities to help monitor day-today variations in ore grindability for the purpose of plant control( 2,3). Of special interest is the algorithm presented by Kapur(3) for the simulation of the Bond test. In practice, the test lasts from 6 to 14 cycles (4 to 10 hours). With this algorithm, one can predict the Bond grind ability using information available from only the first two cycles.Sometimes the prepared feed for the grindability test contains too much fines compared to the total product desired at the mesh of grind under consideration. In such a case, the operator separates the fines from the test feed and adds to the remaining coarse fraction an equal amount of fresh feed. This combined feed then forms the feed to the first cycle of the test. In the present work, Kapur's algorithm is modified to include this special case. A new and relatively simpler algorithm is also presented. Statistical equations relating work index to pertinent variables are also given."

Jan 1, 1981

By William F. Caley, A. MacKinnon, P. W. Kingston

"The purpose of this paper is to identify a number of currently available opportunities for exploration and/or mine development in the industrial minerals field in southeastern Ontario. The paper is not intended as a complete review of the industrial minerals industry in southeastern Ontario, but highlights what are seen by the authors as areas where there are immediate opportunities for investment and growth.Traditional exploration targets in the Grenville Supergroup in southeastern Ontario have been vein-hosted gold deposits, industrial minerals, and base metals. In recent years, emphasis has increasingly shifted to industrial minerals, in response to changing technologies in the minerals-consuming manufacturing industries, and to an increasing awareness of the industrial mineral potential in this area.This paper examines the resurgence of interest in exploring for and developing a wide variety of industrial minerals, and it examines the work the Ontario Ministry of Northern Development and Mines has done under the current Canada-Ontario Mineral Development Agreement. Specific development opportunities are identified in various commodity areas. Use oj the industrial minerals wollastonite and nepheline as substitutes for fluorspar in the formulation of synthetic steelmaking slags is also discussed."

Jan 1, 1990

By Clifford S. Gibson

THESE troubled times suggest three reasons for maximum effort to control silicosis: (1) To keep to a minimum the ever-increasing burden occasioned by past deficiencies in this respect. (2) To effect the greatest production with maximum efficiency, which means at the least cost. (3) To preserve man-power in every way. Good control of the silicosis problem aids these aims. Inadequate control hampers all three. Insofar as our knowledge goes, silicosis in Ontario mines is caused by the inhalation of finely particulate quartz. It follows, therefore, that removal of dust containing this mineral automatically erases the cause. The achievement of this ideal is the aim of the mine operator. His best tool to this end is ventilation. This paper discusses mine ventilation from the viewpoint of dust control and it is hoped that in so doing there may result a better understanding of the part played by air in silicosis prevention. No attempt will be made to treat the subject fully. Instead, there will be presented certain salient aspects culled from field observations, the data in all cases referring to gold mines, unless mention to the contrary is made.

Jan 1, 1942

By Norman A. Jull

"IntroductionThe scope of this paper is intended to deal mainly with cyclones in grinding circuits. However, the section on Cyclone Equipment, contains more general descriptions, to cover most of the cyclones used in mineral separation plants.Cyclones as heavy media separation vessels are discussed by Mark Freberg (this volume). Their use in tailings deslirning is discussed by P.C. Lighthall, eta/. (this volume).Cyclone EquipmentCyclone TerminologyApexObviously, the apex of a cone is the smallest end. However, with cyclones the term is usually used for the fitting which is attached there to control discharge of the underflow stream.Note that the cyclone need not be so mounted that the apex is the lowest point, although that is the most common method. Keeping the apex below the rest of the cyclone helps avoid plugging when the underflow contains very large particles and the tonnage of underflow solids can fluctuate.Various devices for adjusting apex diameter or otherwise controlling the underflow are discussed later under ""Cyclone Construction"".BypassingThe transport of a portion of feed slurry directly to underflow so that classification is bypassed by that portion of feed.This action is fundamental in any hydraulic classification, whether gravity or centrifugal, because the large particles going to underflow have some void volume between them, which remains filled with feed slurry.D50By definition, D50 is that particle size which has an equal probability of going to overflow or to underflow.It is calculated by drawing a curve of recovery vs particle size and noting the size at which 500Jo recovery occurs.This may be done equally with corrected or with gross recovery (see below) and the resulting value should therefore be identified as d50c (corrected d50) or as d500 (gross d50).Note also that it is common in industry practice to plot size analysis data on the retained size rather than on the average of passing and retained (the middle of the size band). To portray sizing alone it makes no difference, but to read a D50 value off a curve of corrected or gross recoveries, it is essential to plot those values on the average size of each band."

Jan 1, 1989

By W. G. Spencer, E. Sulis, P. M. Tiley

"Dome Mine's No.8 shaft is located about 1 km northeast of Dome's No.3 shaft and mill complex in South Porcupine, Ontario.No.8 shaft was brought into production in 1984 to hoist ore and waste for the complete mine as well as to service the mine from the 1600 level and below. Access above 1600 level is provided by No. 3 shaft.The rectangular shaft has six compartments consisting of two skips, a cage, counterweight, manway, and a service compartment. The over-all size of the shaft is 14 ft 7 in. by 20 ft by 7 in. (Fig. 1). A 7th compartment for shaft deepening is incorporated in the bottom 500 ft of shaft. The shaft is 5470 ft deep. The loading pocket is located at 5300 ft and the dump 61 ft below the collar.Surface facilities consist of a concrete headframe and a structural steel hoistroom which houses the cage and production hoists . The service hoist is a 12-ft diameter double drum, with one 1750 HP DC motor, and the production hoist is a 15-ft diameter double drum with twin 1750 HP DC motors.Both hoists have a single clutch and a single reduction gear train built by Orenstein & Koppel, and equipped with Canadian General Electric drives. The cage hoist is equipped with a disc pinion brake.The skips were originally aluminum 14-ton capacity, Rolla-chute design with steel liners on three sides and 4 in. of rubber on the back, to absorb the loading impact. The original guide rollers consisted of fixed 10 in. pneumatic tires. The face-to-face units were eventually replaced with larger airplane-type tires mounted on a spring loaded pivot arm."

Jan 1, 1993

By L. C. Galloway, G. L. Tiley

"Mine hoist brakes must meet the following statutory performance criteria:- There should be two independent braking systems; at least one should act directly on the hoist drum.-If one brake fail s, the others should be able to retard and stop the hoist safely before the descending conveyance, carrying the rated load, reaches any obstruction.- When all brakes apply, decelerations should not be so violent that men travelling in the conveyance are injured.- The brakes shall not overheat and fade during an emergency stop.This paper discusses design principles and capacities of caliper and disc type brakes, when applied to double drum and friction hoists of equivalent capacity.IntroductionThis paper is about the brakes that are used on mine hoists; their functions, especially in emergencies, typical design, and how they are operated, controlled, tested, and adjusted.There are two basic types of mine hoists:1. Drum hoists, where the ropes are attached to, and coil on drums. The simplest system has only one drum. Most such hoists, however, have two drums, attached to a common shaft. Ropes are wound on each drum in opposite directions, so that when one conveyance is being raised, the other is lowered. The conveynaces may travel in vertical or inclined shafts. In the latter case, the hoist s are referred to as slope hoists.2. Friction hoist s, where the headropes are not attached to the wheel, but are in contact with it for an angle of lap of, typically, between 180 and 195 degree s. Forces are transmitted from the hoist wheel to the head ropes by friction.The lower ends of the conveyances are connected to balance ropes , approximately the same weight per foot as the headropes."

Jan 1, 1986

By E. O. Lilge

THE USE of the Driessen cone as a heavy-media concentrator involves a mineral dressing process in which many variables inherent in the ore and in the process may have an effect on the efficiency of mineral separation and the operation of the cone. The magnitude of these effects and their possible interrelationships must be known before a full-scale plant can be designed and built. It appears that, among the most important variables, are the following: Ore Variables: The particle size of feed The difference in specific gravity between economic and non-economic minerals The intimacy of mineral association Cone Variables: Cone inlet area Ore to media ratio Cone ratio Size distribution in heavy media Specific gravity of media Viscosity of media Type of media

Jan 1, 1956

By A. Sutherland Brown

"The ProblemMany science activities receive substantial funding from governments without much direct economic benefit accruing to state or individuals. In contrast, the search for knowledge has never been an acceptable so le justification of geoscience activity, perhaps because of its utility right from its inception. William Smith's geological activities were embraced because of their usefulness in building canals. Utility has been expected ever since.For decades it has been accepted at senior level s of government, without much understanding of the process, that geological surveys are necessary as a basis of resource evaluation and utilization. Recently, government treasury board s, staffed with economist s, have questioned these near axioms and in many cases the budget s of geological surveys have reflected their stone y-eyed appraisal s. Are government surveys necessary? Can their functions be reduced? Can some or all of their functions be privatized?Government geologists have been muted in trumpeting their successes outside their own ranks. Companies have been reluctant to give specific public feedback on the work of government surveys that have truly aided or guided them toward discovery. Lack of acknowledged linkages between survey work and discovery has dogged survey managers in budget reviews. Impoverished surveys cannot perform adequately so the circle is completed and the doubters' prophecy fulfilled. This is the genera l problem; British Columbia is the archetypical province."

Jan 1, 1986

By A. Galip Ulsoy, K. V. S. Sastry

"This review paper is intended to provide, the mineral process engineer with an introduction to the concepts, terminology. and practice of mineral process control. It also provides an extensive sampling of the vast body of literature relevant to this topic. The topics discussed include the principles of automatic control, instrumentation, mineral processing unit operations, process modeling and simulation, and process and plant control. IntroductionEconomically accessible higher-grade ores are being rapidly depleted, and at the same time the demand for mineral raw materials continues to increase. Mineral recovery from the remaining low-grade or finely dispersed ores requires grinding for liberation. High energy consumption during grinding and poor efficiency associated with the beneficiation of fine minerals are two important problems facing the mineral industry . These problems, coupled with advances over the last 10 to 15 years in the areas of process modeling, instrumentation, computer technology and control theory, have made automatic control of mineral processing systems an important research area(23,52,66,67,120,129,152)."

Jan 1, 1981

By A. Galip Ulsoy

This review paper is intended to provide, the mineral process engineer with an introduction to the concepts, terminology and practice of mineral process control. It also provides an extensive sampling of the vast body of literature relevant to this topic. The topics discussed include the principles of automatic control, instrumentation, mineral processing unit operations, process modeling and simulation, and process and plant control.

Dec 1, 1981

By Robin Sheremeta

What is the goal of every organization when it comes to safety? Everyone Going Home Safe and Happy Every Day Good old days: Era of Death (accidents will happen) Era of Engineering: (Eg. hand rails, limitswitches, machine guards, etc.) Era of Legislation: procedures, laws and regulations (Eg. SWP?s, Mines Act) Era of Behaviour-Based Safety: (eg. STOP program)

May 1, 2010

By K. Halada

Current trend of the global flow of strategic metals are analyzed to discuss the strategy of the development of recycling technology and alternative technology. In many cases, each global flow of metal is changing from the trilateral structure of U.S., EU and Japan in the later 20th century into the convergence to China as the factory of the world. Scrap flows are also changing dynamically. A long term change of prices of metal has gotten changed since the entrance of this century. The estimation of metal consumption up to 2050, in which the author estimated that many kinds of metal will overshoot the reserve base line, is revised considering these change of current trends.

Jan 1, 2014

By Michel Gauthier, Pierre Marcoux, Gaétan Morin

"The recent opening of Muscocho's gold mine at Montauban, as weil as the discovery of several new copper-gold showings of a similar nature near the confluence of the Saguenay and St , Lawrence has revealed the existence of a new metallogenic gold province which is located within supercrustal units of Helikian age within the Grenville Province. Three metalliferous belts have been identified, each one of which is related to a series of SW-NE trending faults. The first is located in southeastern Ontario and southwestern Quebec. The second extends from the Balmat-Pierrepont mining district of New York State up to the Lac St. Jean region of Quebec, and includes the Montauban camp. The third follows the St. Lawrence river in Charlevoix County and along the north shore of the Gulf of St. Lawrence.The gold mineralization which is present in the central portion of the Grenville Province is of two types: either stratiform or vein. Deposits of the first type, of which the Muscocho is the type locality, are economically the more interesting of the two. Not only is this mineralization stratiform, but also shows a distinct affinity to AI-rich, Mg-rich or calc-silicate-rich bands. As is the case with the Bousquet and Hemlo regions of the Superior Province, they are associated with layers which are rich in sillimanite and occasionally staurolite. A second parallel between the Bousquet and Montauban deposits might be the presence of manganesian gamets, which have been recognized at the two localities. Some of the mineralization in the central Grenville Province is located within thin bands of iron formation which are rich in arsenic.The stratiform gold deposits of the central Grenville Province are of exhalative origin and are located within a volcano-sedimentary terrane. It is probable that a part of the gold present in these Helikian deposits have been derived by remobilization of Archean mineralization. The vein showings form as a consequence of the remobilization of the Helikian strata during the Grenville metamorphism,"

Jan 1, 1985

By Michel Gauthier, Jacque Trottier

"ForewordA symposium on base metal deposits was held in Bathurst, New Brunswick, from June 10-13, 1990, sponsored jointly by the Geological Surveys Branch of the New Brunswick Department of Natural Resources and Energy, the New Brunswick Prospectors and Developers Association, and the Geology Division of the Canadian Institute of Mining, Metallurgy and Petroleum. Papers prepared for the symposuim are being published as a series of articles in the CIM Bulletin. This third paper (the first was by Fyffe, et al., in Vol. 83, No. 938, the second is in this issue) in the series presents an overview of the tectonic setting and geochemistry of base metal deposits in the Eastern Townships of Quebec.ABSTRACTIt is well known that the classification system of volcanogenic massive sulphides (VMS) is based upon their metal content. This metal content, the result of hydrothermal solutions circulating within strata underlying the deposits, is generally thought to be related directly to two parameters: (1) the nature of the underlying stratigraphic sequence; and (2) the physico-chemical conditions that existed at the time of the hydrothermal event. Furthermore, these two parameters are, in turn, related to the tectonic setting. One must bear in mind that these parameters are diachronous and evolve with time. These factors are considered in our analysis of the major VMS deposits of the southeastern Quebec Appalachians. This analysis will describe the time and environment of formation of these deposits and integrate them into an evolving paleotectonic model.VMS deposits in the southeastern Quebec Appalachians formed during three distinct metallogenic episodes. During the first episode, which involved early closing of the Iapetus Ocean and associated destruction of oceanic crust by subduction processes(Early Ordovician?), cupriferous VMS deposits hosted by pillowed, mafic (boninitic) lava flows were formed in immature island-arc systems (""Cyprus-type"", e.g. Huntingdon deposit).In the second episode, which also occurred during the closure of Iapetus but at a later stage (Early to Middle Ordovician), mature island-arcs formed and hosted polymetallic VMS deposits (""Kuroko-type"", e.g. Eustis deposit).Finally, during culmination of the Taconic and/or Acadian orogenies (Middle Ordovician and/or Devonian), transtensional basins, associated with tholeitic to transitional mafic volcanism began to develop. Major sedimentation occurred contemporaneous with volcanism, and within this framework polymetallic VMS deposits were formed (""Besshi-type"", e.g. the Memphremagog deposit).Although incomplete, the proposed paleotectonic model represents the sequence of the tectonic settings that prevailed during the formation of the VMS deposits of the southeastern Quebec Appalachians."

Jan 1, 1991