Search Documents

By E. Lehtila, J. J. Talja, R. Jahila

Kopar Oy is acknowledged for engineering and manufacturing of robust systems for bulk material handling, especially at power plants and non-ferrous smelters. We have over thirty years of experience with systems specifically designed for hot and abrasive conditions, aiming at low cost of ownership, low operational expenses and high availability. Although Kopar has numerous applications in mechanical conveying, there is an increasing number of pneumatic conveying applications at copper smelters. They relate to conveying of concentrate, and primary and secondary flue dusts. Challenges of pneumatic conveying for concentrate are mechanical and do relate to broad particle size distribution and high abrasivity of the concentrate and the silica. Therefore, special attention shall be paid to system design and ceramically lined bends in the pipeline. Challenges of pneumatic conveying of primary flue dust relate predominantly to material stickiness and poor flowability which are mainly due to fine particle size and formation of sulphates and furthermore, crystalline water. Additional challenges of secondary dust, the white converter dust, are primarily due to the extremely fine 0.1–1.5 µm particle size and problems which come with this. Effect of material characteristics like size distribution, morphology and chemical composition in pneumatic conveying are discussed in detail. INTRODUCTION Fine materials like concentrate, feed mix, flue dusts (from waste heat boiler and electrostatic precipitator) and secondary dusts need to be conveyed at smelters. Both horizontal and vertical conveying and combination of those are used. For the purpose, both mechanical and pneumatic conveying are applied. Most widely used equipment are drag chain conveyors and various combination of pneumatic systems, e.g. air lift, dense-phase and dilute phase pneumatic conveyors. Kopar has 30 years’ experience with multiple material handling systems. Furthermore, acquired companies like Elmomet Oy and SITE Oy (both currently fully merged and integrated into Kopar Oy) have even longer history, especially in pneumatic conveying. It is commonly known that the finer the dust the more difficult it is to be conveyed pneumatically. Sulfates with crystal water makes it all even more difficult, if not ineligible. Challenges related to pneumatic conveying of various fine materials is discussed in detail in the paper.

Jan 1, 2019

By Carricajo T., S. Nazari

This paper discusses a unique dynamic solution for optimizing comminution area in real time. The proposed technology is a combination of model predictive controller, optimization methods and real-time digital twin for mineral processing. For grinding area, the ultimate goal of an effective control strategy is to maximize the mineral processing, reduce energy consumption and stabilized size classification. To have a continuous and effective comminution operation, a reliable control system that minimizes the need for human intervention is necessary. The implemented advanced control strategy for comminution area consists of two layers in hierarchical structure. The lower layer objective is to stabilize the process stabilization using model based predictive controller (MPC) technique. The unique MPC used in this layer is called BrainWave™ chosen for its robustness, convergence and delay handling; furthermore, the developed platform offers stable and repeatable solution and has short implementation time. The upper layer is a supervisory control, which sends the preferred process operation points to the lower layer to drive the process towards optimal performance. The goal of this layer is to optimize the process targets, as well as making decision. To increase process performance, automatic ore characteristic adaptations are implemented in this layer. A digital twin of comminution area is built in the second layer that runs amongst the process in parallel. By communicating, the process data in real time, a virtual densitometer is built that is being used in our advance process control strategy. Our control strategy has been developed, tested and implemented in various areas of a copper concentration plant. The targets for implementing advance process control are usually increased throughput, decrease energy consumption and variability reduction in particle size distribution. Overall, the results showed in different mine sites are increase throughput between 2 and 5%, specific energy consumption reduction about 15% and process variability reduction up to 60%. In this paper we discuss the results of the recent implementation of this technology on Minera Los Pelambres, Minera Collahuasi and CAP Minería. Their concentrator plants have installed control systems with the most updates optimization features, for SAG mill, ball mills and thickeners.

Jan 1, 2019

By K. Heid

"Although concentrated efforts have been made to deplete PCB transformers from the Canadian environment, numerous transformers (as well as ballasts, capacitors and magnets) continue to exist throughout the Canadian mining industry. The existing installed base is slowly being phased out as environmental issues come under increasingly high profile. The following article identifies the potential problems of owning PCB transformers and offers some solutions for their removal, disposal and replacement. IntroductionPolychlorinated Biphenyls (PCB) are synthetic chemical compounds consisting of chlorine, carbon and hydrogen. PCB was widely used in transformers due to its physical properties, including stability, low flammability and non-conductivity. Use of PCB in electrical equipment has been banned since 1977 when the extent of environmental contamination was discovered.Although PCB’s have been outlawed for use in electrical equipment since the late 1970s, safe storage regulations were not addressed until 1988 when a major spill prompted the federal government eventually to issue the storage of PCB Material Regulations in 1992. These regulations replaced the Interim order of 1988 under the Canadian Environmental Protection Act.PCB transformers are usually referred to as askarel filled transformers or as PCB contaminated mineral oil transformers. Askeral transformers were designed to contain high concentration PCB fluids, referred to as askarel. Mineral oil transformers were not designed to have PCB concentrations but were inadvertently contaminated during manufacture or maintenance activities."

Jan 1, 1998

By H. P. Whaley

This paper introduces Wabush Mines, including its ownership, physical assets, capacity, goals and achievements. It is to be followed by four papers which will present the detailed story. Wabush Mines, the largest supplier of iron ore to the Canadian steel industry, was brought into production in 1965. The ore is mined and concentrated in Wabush, Labrador, Newfoundland and pelletized at Pte. Noire, Quebec. Annual capacity is over 6,000,000 tons of high-grade iron ore pellets.

Jan 1, 1969

By C. W. MacLeod

LOCATION The Goudreau gold area in Ontario extends from a point a short distance south of the main line of the Canadian Pacific railway, at Lochalsh, in a south-westerly direction to the Magpie river. It crosses the Algoma Central & Hudson's Bay railway at Goudreau station, 177 miles north of Sault Ste. Marie. The area is roughly 25 miles in length by 6 miles in width. The potential gold formation is much more extensive but little prospecting has been done outside of the limits mentioned. The actual continuous area of Keewatin formation, in which gold has been found, is one of the largest in Ontario. ACCESSIBILITY Probably no mining area in a similar stage of development has had the excellent transportation facilities which Goudreau enjoys. This field is traversed in part by the main lines of the Canadian Pacific and Algoma Central railways. The Provincial Government has constructed 22 miles of road through the heart of the camp. Sixteen miles of this road is suitable for motor car traffic and several cars and trucks are in constant service.

Jan 1, 1926

By David Deglon, Martin Harris, Mehdi Safari

"This study investigates the effect of energy/power input on the flotation of a platinum ore in a pilot-scale oscillating grid flotation cell. Oscillating grids generate near ideal hydrodynamic environments, characterised by turbulence which is relatively homogeneous and isotropic. Secondary rougher feed and primary cleaner tail streams were floated in a pilot-scale oscillating grid flotation cell at power inputs from 0 to 2.5 W/kg, using 0.50 and 1.50 mm bubbles. From this study one may conclude that the effect of energy/power input on the flotation rate is strongly dependent on the particle and bubble size. Flotation rates generally increase with increasing particle size and decreasing bubble size. Increasing energy input generally leads to an increase in the flotation rate for finer particles and an optimum flotation rate for intermediate & coarse particles. Optimum conditions for intermediate/coarse platinum ore particles are using small bubbles at low energy inputs, or large bubbles at higher energy inputs. These results suggest that higher energy inputs are generally beneficial for the flotation of platinum ores as these consist predominantly of finer particles (-75 µm) and most industrial flotation applications operate with larger bubbles (1.0-2.0 mm).INTRODUCTIONThere is a considerable body of experimental and theoretical evidence to suggest that energy/power input plays an important role in flotation kinetics, particularly in the finer particle sizes where flotation efficiency is poor (Deglon, 2005). A number of excellent studies into the effect of energy on flotation kinetics have been carried out in impeller stirred cells (Ahmed and Jameson, 1985; Deglon, 2002; Pyke et al., 2003; Newell and Grano, 2006). Investigations using this type of cell have a number of limitations. The impeller influences particle suspension, bubble break-up and agitation in the cell. In addition, turbulence is highly inhomogeneous and anisotropic, with power intensities near the impeller orders of magnitude higher than those found elsewhere in the cell (Deglon, 1998; Koh and Schwarz, 2003; Schubert, 1999, 2008). These limitations have resulted in the development of novel cells for the investigation of energy input."

Jan 1, 2016

By K. Waters, A. Navarra, T. Grammatikopoulos

Strategic decisions to develop a mineral deposit are subject to geological uncertainty, due to the sparsity of drill core samples. The selection of metallurgical equipment is especially critical, since it restricts the processing options that are available to different ore blocks, even as the nature of the deposit is still highly uncertain. Current approaches for long-term mine planning are successful at addressing geological uncertainty, but do not adequately represent alternate modes of operation for the mineral processing plant, nor do they provide sufficient guidance for developing processing options. Nonetheless, recent developments in stochastic optimization and computer data structures have resulted in a framework that can integrate operational modes into strategic mine planning algorithms. A logical next step is to incorporate geometallurgical models that relate mineralogical features to plant performance, as described in this paper.

Jan 1, 2017

The Nak?azdli First Nation and the municipality of Fort St. James are located in the Stuart Lake/Nak?al Bun area and are not unfamiliar to mining. These northern British Columbian communities have been associated with the historic Pinchi Lake Mercury mine and today are closely linked with British Columbia?s newest mine, the Mt. Milligan mine. Prior to the construction of Mt. Milligan, community health and social service providers were concerned about potential impacts that would occur from new mineral development activities. This concern has led to a partnership between the above communities and researchers with expertise in the area of mining and health. This paper describes: the current mining and health environment with a focus on British Columbia; mining trends in the Stuart Lake/Nak?al Bun area; the current community-based health research project funded by the Vancouver Foundation and the Canadian Institutes of Health Research, and; a suite of community-based health recommendations to mining companies on key issues to consider when developing projects near municipalities and Aboriginal communities in Canada, based upon one of the newest mines under development in Canada.

Aug 1, 2013

By J. Gray, J. Peck

As the turn of the century approaches, traditional open pit mining methodologies and processes are being modified through the introduction and use of new technologies. As in other industries, the personal computer is dramatically changing the traditionally conservative mining industry by allowing mines of varying size and capacity to increase their productivity and efficiency through the use of easy to use, office software. Computer-based monitoring and control systems are also being used more frequently to measure and optimize, in real-time, the performances of operating equipment. When communicated to an end-user, this information can provide accurate and timely answers to questions of how much, where, when, and by whom. This capability forms the foundation of a more comprehensive, proactive management and planning facility where, ultimately, information acquired from the producing equipment will be used to optimize and control machine and human activities. As these technologies mature and become essential tools in a mine, they will eventually serve as the basis for more robotic and autonomous mining operations.

Jan 1, 1999

By Wataru Inagaki, Kozo Kawano, Tetsuya Ando

Cu–Ni–P alloys are the typical precipitation-hardening material. Thus, Cu–Ni–P alloys is expected to apply alternative materials for heat-exchanger tubes. Therefore, it was investigated that the effect of the heat-treatment simulated brazing on mechanical properties of Cu–Ni–P alloy in this study. The hardness of specimen as heat-treatment simulated brazing after solution heat treated (sht) was shown approximately 105 HV. The peak hardness and tensile strength of the specimen as performed aged at 498 K for 43.2 ks following the heat-treatment simulated brazing achieved at approximately 140 HV and 260 MPa, respectively. From these results, it is expected the application to higher-strength tube for heat-exchanger after brazing in a furnace. INTRODUCTION Copper prices have increased dramatically with high in recent years. At the same time, manufacturing industries are required to reduce the environment load by reducing the wall thickness of the copper tubes used in heat exchangers. High-strength copper alloys are developed for reducing the wall thickness, while achieving high strength, of the copper tubes. Moreover, excellent workability and corrosive durability are also required by these copper tubes. Furthermore, the brazing, which are carried out at about 1050 K during the assembly process of heat exchangers, leads to grain growth and re-solving of additive elements. Nomura et al. achieved a tensile strength and Vickers hardness of approximately 260 MPa and 110 HV, respectively, after aging at 723 K for approximately 36 ks. Tamagawa et al. studied that the strength of Cu–Ni–P alloy rapidly increased at about 125 HV during the cooling process after the heat brazing due to the Ni2P precipitates sized 5–10 nm. Furthermore, Inagaki et al. achieved a Vickers hardness of approximately 130 HV by aging at 498 K for 10.8 ks. In the present study, we focused on the lowest aging temperature of 498 K in the previous study, and investigating the effect of heat-treatment simulated brazing on the mechanical properties of the Cu–0.93 mass%Ni–0.24 mass%P alloy.

Jan 1, 2019

By CIM Standing Committee

The CIM Definition Standards on Mineral Resources and Reserves (CIM Definition Standards) establish definitions and guidance on the definitions for Mineral Resources, Mineral Reserves, and mining studies used in Canada. The Mineral Resource, Mineral Reserve, and mining study definitions are incorporated, by reference, into National Instrument 43-101 – Standards of Disclosure for Mineral Projects (NI 43-101). The CIM Definition Standards can be viewed at mrmr.cim.org. Readers should be aware that reports written by persons issuing technical reports that disclose information about exploration or other mining properties to the public in Canada are governed by a number of securities regulations.

May 10, 2014

By M. Bavand-Vandchali, F. Golestani-Fard, S. Khalili, S. Rowshanfekr-Fallah

In the secondary metallurgy of steel, the availability of ladles plays an important role in decreasing the production cost. The refractory lining, therefore, should satisfy optimized quality to grant higher heats. This paper reports the results of an investigation carried out in Iranian Mobarakeh Steel Company in order to increase the lining life of ladles by employing different types of MgO C and Al203 - Mg° - C. The zoning concept was used in replacing the conventional refractories either in slag line or the lower parts of ladle. The number of heats could be improved to almost two times as before. The results are explained in terms of refractory quality as well as zoning approach. The economical impact of this improvement will also be analyzed.

Jan 1, 2004

By E. Paransky, M. Rigaud, G. Paschek, S. Palco

Some of the negative impacts of carbon addition on the strength of castables are yet to be overcome in order to fulfill its potential benefits for oxidation resistance. This paper reports the results of recent studies conducted at CIREP on the effects of different types of carbon additives on the thermo-mechanical properties of magnesia-based castables. Experimental techniques included measurements of the hot modulus of rupture (HMOR), hot modulus of elasticity (HMOE), as well as the wedge-splitting test (WST). The comparison of evolving microstructures was carried out employing scanning electron microscopy with microanalysis attachment (SEM/EDS) and X-ray diffraction (XRD). HMOR values of 12 MPa at 1300°C have been reached in MgO-Si02-C castables containing up to 7% carbon.

Jan 1, 2004

By S. -H. Sohn, M. -K. Cho, G. -G. Hong

In order to evaluate the properties of coating materials for BOF, the effects of dolomites (dolomite and light burned dolomite) addition on durability of coating materials were investigated. In all coating materials, matrix was dicalcium ferrite(C2F) and both free MgO and dicalcium silicate(C2S) were precipitated. Fe203 content must be controlled to improve the adhesion and durability of coating materials for BOF during oxygen blowing process. The amount of dolomites added to BOF slag must be controlled in optimum condition with high refractoriness of C2S to improve the adhesion of coating materials for BOF. The weight ratio of converter slag to dolomite must be below 8 to improve the adhesion and durability of coating materials simultaneously.

Jan 1, 2004

By M. W. Bartley

"The Steep Rock iron mine is 141 miles west of Port Arthur, Ontario, and 50 air miles north of the Vermilion iron range in Minnesota. The property lies 27'2 miles north of the village of Atikokan on the south line of the Canadian National railway.The orebodies underlying the bed of Steeprock lake, since de-watered, were known to exist 60 years ago. References to the possibility of iron ore at this location were made in early geological papers and reports. In 1937 the locations of the orebodies were determined by dip-needle surveys, and from 1938 until 1943 diamond and churn drilling were carried on to prove their extent and configuration. It was found that the ore, in addition to being associated with definite types of wall-rock, was controlled by structural features, such as faulting and brecciation. From this geological knowledge the presence of other deposits has been inferred, and these are now being explored and developed.Production at the property commenced in October 1944. During that season 17,000 gross tons of ore was shipped. In 1945, 506,000 gross tons and in 1946, 830,000 gross tons was mined and shipped. In 1946, 164,000 gross tons additional was placed on stockpile for future shipment.TYPES OF 0REBODIES AND MINERALIZATIONThe orebodies at Steep Rock iron mine are tabular. They have an average width of 250 feet, lengths up to 5,000 feet, and persist to known depths of 1,200 feet. They are replacement deposits in brecciated carbonate rock at the contact of underlying pseudo-limestones and overlying volcanics. The ore is composed of hematite and hydrous hematite in the form of goethite, turgite, and limonite. These minerals replaced the brecciated host rocks metasomatically as a result of hydrothermal action. The replacement followed a definite structural pattern along the unconformable contact between the sediments or other rock (now replaced by carbonate) and the volcanics, subsequent to disturbances in the form of minor faulting and shearing. The faulting and shearing provided the channels through which the replacing solutions percolated. It is believed that the late basic intrusions outside the ore zones were genetically responsible for the introduction of the ore-bearing solutions."

Jan 1, 1954

By T. Newton, G. A. Bezuidenhout, P. J. Tauetsile, F. Trask

The technology to selectively leach gold, silver and base metals from ores, concentrates, and wastes, using an alkaline glycine solution, has initiated significant interest in using the new technology in various environments such as in-situ, in-place, dump, heap, and vat and agitated tank leaching. It has been shown that glycine acts synergistically with a number of other lixiviants to lower the net consumption of the other lixiviants while allowing low cost glycine solution recovery. Glycine is a non-toxic, stable, environmentally benign reagent that is available in bulk industrial quantities. It has the ability to dissolve most copper oxide and sulfide minerals, as well as native copper, whilst not interacting with acid consuming gangue nor dissolving iron and various or ubiquitous gangue elements. It acts synergistically with small amounts of cyanide to leach gold-copper ores at leach rates higher than either glycine or cyanide on their own, while significantly reducing cyanide consumption and eliminating detoxification requirements. The leaching behaviour of various glycine based systems will be reviewed, followed by the evaluation of the adsorption of gold onto activated carbon. Where the economics merit it, copper can be easily recovered using solvent extraction or sulfide precipitation.

Jan 1, 2017

By J. W. Jefferies

"Plant availability up 13%, production output up 40%, tons per employee up 15% and labor turnover down 52%. One mine manager states these were direct spin offs from the work being done to qualify for a safety award in the program known as the ""IMSRS 11 over a three-year period of time. ""Of Course"", stated this manager, ""these were in addition to an 87% reduction in our disabling injusry frequency rate.”Officially known as the International Mine Safety Rating System or the Five Star Mine Safety Rating, a new approach to mine safety is being used with enthusiasm by a significant number of mines in Canada, the U.S., Australia, Chile, Indonesia, the Philippines and South Africa. Significant results are coming into the International Loos Control Institute from over 125 mines from these countries.The program is built around a mine safety audit system that gives positive recognition to a mine at 5-step intervals along the way, (a star with each step attained). The Institute has licensed auditors in locations in Canada and the U.S. available to audit.It is believed the success of this program is the result of the premise upon which the program is based. The results being achieved are due to the concept that a modern, well-managed mine safety program maintains the basic foundation of a complete management system. When properly implemented, it reinforces those factors common to production, quality and safety. (Attitude - skill - knowledge - fitness - structure - machine - equipment - materials and processes). The IMSRS contains elements that reinforce all these factors. It uniquely treats safety as part of the ""right way"" to do the job and not just the ""safe way"" as a distinctly separate entity. Mines using this program now recognize that many of the older safety techniques were not necessarily the right way or the most efficient way to do things. It appears that this new approach to mine safety is a new avenue for the attainment of management's real goals for being in business, and at the same time achieves optimum support for the important target of safety and health for the mine worker."

Jan 1, 1983

"Adopted in 2003, theses guidelines are intended to assist the Qualified Person(s) in the planning, supervision, preparation and reporting of mineral resources and mineral reserve estimates. The report is divided into two broad sections “General Guidelines” appropriate for most metals and “Guidelines Specific to Particular Commodities” for potash, industrial minerals, uranium and coal. “These guidelines are reference in the Companion Policy of NI 43-101 with a statement that a qualified person classifying a mineral deposit as a mineral resource or mineral reserve should follow them.”Executive SummaryThe following is a summary, in table format, of the main elements of the Estimation Best Practice Committee's report ""Estimation of Mineral Resource and Mineral Reserve Best Practice Guidelines"". While the summary table is provided for convenience, the Committee recommends that the report be read in its entirety and the table summary not be used as a stand alone document. These guidelines are not intended to be either prescriptive or exhaustive. They do not preclude innovation. Preamble: These guidelines have been prepared by the Canadian Institute of Mining and Metallurgy and Petroleum (CIM) led Estimation Best Practices Committee. They are intended to assist the Qualified Person(s) (QP) in the planning, supervision, preparation and reporting of Mineral Resource and Mineral Reserve (MRMR) estimates. All MRMR estimation work from which public reporting will ensue must be designed and carried out under the direction of a QP in accordance with National Instrument 43-101 (NI 43-101) and related forms. A QP is defined in NI 43-101 as ""an individual who is an engineer or geoscientist with at least five (5) years of experience in mineral exploration, mine development, mine operation, project assessment or any combination of these; has experience relevant to the subject matter of the mineral project and technical report; and is a member in good standing of a professional association"". Disclosure of MRMR estimates is to be made in accordance with industry standard definitions approved by the CIM (the CIM Standards adopted by the CIM Council in August 2002) which have been incorporated by reference into NI 43-101."

Jan 1, 2003

By J. K. Gowans

The Research and Design group of the Project Development Division (PDD) of Placer Dome Inc. includes metallurgical, electrical, civil and mechanical engineers. They provide metallurgical research and conceptual flowsheet development, feasibility concepts for the processing and ancillary facilities, and manage the detailed design of the facilities once approval has been given to a mining project. This paper describes how this group works, within the Project Development Division, to help develop feasibility studies with the Evaluations Group, manage detailed design, and provide support for the Construction Group. The paper briefly reviews the history and growth of the group and describes how it is evolving. The role of outside engineering firms and how they are incorporated into the division’s objectives are also discussed. The paper highlights the differences between Placer Dome’s Project Development Division and other mining groups, and why this approach fits the way Placer Dome does business.

Jan 1, 1998

By Gordon T. McKenna

"Syncrude Canada Ltd. is developing new concepts in lease-closure landscape design for its Oil Sands Leases 17 and 22 in northeastern Alberta. Closure planning is becoming an integral part of the planning cycles and of the lease operation. By incorporating closure planning into the day-to-day operation, the company will achieve acceptable lease closure in an economical manner. Ultimately, Syncrude will achieve lower operating costs through innovation in mine planning and a reduction in residual liabilities.New concepts being evaluated for lease-closure landscape design include: designing for closure, use of landforms and natural analogs, self-armouring bouldery ground, robustness in design, landform grading, terrain analysis of reclaimed land, geotechnical hazard assessments, choices in closure design timeframes, passive maintenance, determining post-closure monitoring goals, engineering tailings, engineering other substrates, use of test plots and field demonstrations, geomorphologic monitoring of reclaimed lands, defining closure goals, and visiting other mines. These concepts are being formalized under the new discipline of Landscape Engineering."

Jan 1, 1996