Search Documents

By Jan Kvinge, Aina Opsal Bakke, Yanjun Li, Jan-Ove Løland, Svein Jørgensen

"Compound casting is a very attractive approach to reduce the weight of components for some specific applications while keep both the functional and the mechanical property requirements. In this work, Al-7Si-Mg alloy /copper compound castings were produced through a low pressure die casting process. To reduce the oxide present in the interface, flux coating of the copper pipes was tested. The interface layer formed between the two alloys was investigated using Optical Microscopy (OM), Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray Spectroscopy (EDS). Vickers Micro-hardness was also measured across the interface. Results showed that the flux coating prevented the formation of the metallic bond between copper and aluminum. Instead, high concentrations of potassium, magnesium and fluoride, coinciding with formation of KMgF3 and MgF2, were detected in the interface. In the castings without surface treatment, a continuous metallurgical bond was achieved. In the bond layer, various Al-Cu intermetallic phases have been detected. In addition, formation of primary silicon particles in the reaction layer was observed in all castings. The mechanism for the formation of the intermetallic phases and the strength of the interface layer have been discussed.INTRODUCTION Recent development in the automotive industry has focused on producing lightweight components, which can reduce CO2 emission and increase the efficiency. Often, one material alone is not able to meet the requirements for a specific use. The need for lightweight bimetallic components has therefore increased. Aluminum-copper bimetallic components can be used in wires and bus bars where conductivity is an important factor (Lee, Bang, & Jung, 2005). Compared to Al-Cu alloys, Al-Cu bimetallic components can reduce both weight and cost without reducing electrical and thermal conductivity (Sheng, Yang, Xi, Lai, & Ye, 2011). A challenge is, however, that aluminum and copper have high affinity to each other, especially at elevated temperatures. This causes formation of brittle intermetallic phases with high electric resistance (Liu, Wang, Sui, Wang, & Wenjiang, 2016). In addition, both metals are subjected to oxide formation on the surface. Copper is especially exposed to oxidation at elevated temperatures (Pinnel, Tompkins, & Heath, 1979), while a thermodynamically stable oxide layer will spontaneously form on the aluminum surface (Papis, Loeffler, & Uggowitzer, 2009). Oxides are known to be passive substrates, which will reduce wettability and will thus prevent the formation of metallic bonding between aluminum and copper (Papis, Hallstedt, Löffler, & Uggowitzer, 2008)."

Jan 1, 2018

By P. M. Y. Waye, R. Yewen

"As mines utilize more automation in mining operations to improve efficiency and safety, a corresponding increasing demand is placed on the transport of information. Some of the recent technological advances in underground telecommunications are described for various data, voice and video applications. In particular, two new innovative underground communication systems are described, one with highspeed data at 30 Mbps and the other for minewide evacuation and safety applications.The high-speed data system incorporates state-of-the-art data networking technologies and the existing leaky-cable, narrow-band radio channels. The new system provides over the same basic infrastructure — the highspeed data network at 30 Mbps TCP/IP Ethernet with 100 Base-T interconnection, plus 32 narrow-band radio channels.The second system is a system for minewide evacuation with “through-the-earth” communication infrastructure. Emergency situations can be communicated to and from all the miners within seconds through a central control location. The technology involved does not require leaky cable or any other similar transmission media installation. Many applications are possible, including warning miners of emergency situations, mine rescue operation to communicate with trapped miners, and regular reporting from miners working alone."

Jan 1, 2002

By Jacek Paraszczak

L?exploitation rentable des gisements de type filonien constitue un problème important dans le contexte actuel de l?industrie minière québécoise. Les études effectuées depuis 1994 ont indiqué, que la technologie d?abattage mécanique utilisant l?outil hydraulique appelé « éclateur radial-axial » constitue une alternative intéressante par rapport aux méthodes conventionnelles par le forage et sautage. Les essais du prototype de l?éclateur ont prouvé qu?il est en mesure d?abattre les roches dures dans un environnement minier, mais sa performance dans les termes de masse du roc abattu dans une unité de temps a soulevé certaines doutes. Pour cette raison, une étude de préfaisabilité de l?éclatage en tant qu?une technologie d?excavation souterraine a été réalisée. Cet article présente quelques résultats des travaux effectués dans le cadre du contrat octroyé à l?Université Laval par le Ministère des ressources naturelles du Québec. Leur objectif principal consistait à comparer, pour les conditions des gisements filoniens, la productivité et les coûts des méthodes d?exploitation souterraine utilisant l?éclatage par rapport à celles conventionnelles. Deux variantes proposées de cette méthode ont été comparées avec la méthode conventionnelle sur le plan du coût (par tonne de minerai) et de la teneur de coupure de minerai d'or. Les études ont démontré que l?application de l?éclatage représente un potentiel de réduire ce coût, surtout dans les situations où l?abattage sélectif pourrait avoir lieu. Pour le cas de base on a trouvé, qu?il serait possible de réduire la teneur de coupure par la marge d?environ 16 ? 26%. Toutefois, les études de sensibilité ont démontré, que le coût dépend de façon important de la productivité d?éclatage, qui, pour sa part, varie beaucoup en fonction de paramètres du massif rocheux devant être abattu.

Oct 1, 2001

By W. M. Tupper

Municipal governments recognize the importance of aggregates in the local economy and the need to manage this resource in the interest of the public good. They have encountered problems with regulating the industry and the dichotomy between the urban need and the rural source. They have suffered from a lack of financial benefit, an adequate aggregate inventory, provincial strategy, economic information and public understanding. A provincial strategy for ensuring the availability of aggregate supplies to developing areas of the Province is essential. The Province should also be responsible for licensing, research, technical expertise on rehabilitation, public education and financial assistance. Upper-tier municipalities (regions or counties) should assume responsibility for resource management, including resource availability, demand characteristics, truck routing, phasing of resource development and sequential land-use planning. Area municipalities (towns and townships) can best determine the social and environmental impact of a specific aggregate development proposal and should therefore have the primary responsibility for the location of new pits and quarries. They should also have the authority to supplement provincial regulations concerning operating standards and the phasing and standards of site rehabilitation.

Jan 1, 1978

By Patrice Nadeau, Yuejun Zhang, Dan Chen, Liming Huang, Claude Gagnon

"The traditional Denver flotation cell is generally suitable to process material ranging approximately from 5 µm to 300 µm. For floating over 300 µm material, its efficiency is significantly getting lower mainly due to the difficulty to suspend coarse particles uniformly, which decreases the chances of particles to attach to bubbles and increases the chances of detachment.RTFT (Rio Tinto Fer et Titane) owns one of the world’s largest hemo-ilmenite deposits. Considering the whole processing technology, the ore is only crushed to -1180 µm. The crushed ore contains about 0.32% S and most of the sulfur is removed by rotary kilns in the ore preparation plant. In order to achieve a similar S reduction, without emitting SO2 into the air, an alternative technology by flotation was pursued.Laboratory and pilot scale-up tests showed that traditional Denver flotation cell could perfectly remove the sulfur from the material sizing 0-300 µm. For the coarser particle sizes, two different models of equipment were tested to improve flotation efficiency: HF (HydroFloat Separator) from Eriez and CLF from BGRIMM (Beijing General Research Institute of Mining and Metallurgy), China. The D6” HF, which is a device that combines flotation and gravity separation, demonstrated its ability to recover those very coarse particles. As compared to the Denver flotation cell, the modified 25 L CLF coarse particle flotation cell achieved better results at higher pulp solids percentage and with a shorter flowsheet."

Jan 1, 2016

By X. Cao, X. -G. Chen, K. Liu

As is well known, the standard Al-Cu 206 cast alloys have extremely low iron contents, usually less than 0.15 wt. %. Recently it is found that the iron contents of the 206 cast alloys can be extended up to 0.5 wt. % through the precise control of the iron-rich intermetallic phases. In the present work, the tensile fracture surfaces of the 206 cast alloys with various iron contents are systematically analyzed to understand the failure mechanisms. Results show that higher iron contents can reduce the tensile properties (especially the ductility) of the alloys mainly due to the increasing volume percent and size of the iron-rich intermetallics. Tensile failure mainly occurs at the iron-rich intermetallics/matrix interfaces for the platelet ß-Fe, but by the self-disassociation for the Chinese script a-Fe and Alm(FeMn). Cracking is easier to initiate and propagate along the longitudinal axis of the platelet intermetallics, but it can be deflected along the branches/arms of the Chinese script iron-rich phases, making the alloy more resistant to the propagation of the cracks, and thus the Chinese script iron-rich intermetallics are less harmful than platelet ß-Fe. In addition, it was also found that the Chinese script a-Fe has even a less damaging effect compared to the Chinese script Alm(FeMn) due to the relatively small size and compact morphology.

Jan 1, 2014

By A. H. Winckers

"The Sullivan Mine and Concentrator are owned and operated by Cominco Ltd. and are located in the Rocky Mountain Trench, in Kimberley, British Columbia.The Sullivan Concentrator commenced operation in 1923 at approximately 2,500 tons per day. The concentrator was enlarged in several stages and by 1945 was treating 8,500 tons of ore per day. In 1949, the capacity of the concentrator was expanded to 10,000 tons per day with the completion of the sink and float plant, the installation of the rod mill, an underground crushing plant and a 4-mile underground and surface electric railway from the underground crushing plant to the concentrator. Throughput now averages 7,000 tons per operating day, or 2,400,000 tons per year.The concentrator operates 7 days per week, 24 hours per day while the underground crushing station operates 5 days per week, 24 hours per day. The ore is essentially a replacement deposit in argillaceous quartzite of Precambrian age. The ore bodies are massive deposits consisting of fine grained mixtures of sulphides, sometimes interbanded with the country rock and varying widely in their content of lead, zinc, iron and silicates. The principal economic minerals are galena and marmatite (7 ZnS:FeS). Iron is mainly present as pyrrhotite, and to a much lesser extent as pyrite. The intimate association of these sulphides necessitated the development of a successful differential flotation process before the ore could be beneficiated profitably."

Jan 1, 1981

By A. Brown

"The mining industry is no exception to the general rule that continuing research is essential to good management; in fact, because of the imperfect state of knowledge in regard to many important factors associated with a mineral extraction, mining research assumes a position of unusual importance. On the basis of a recent visit to mining research centres in a number of European countries, the author describes their organization and their role in the mining industries of these countries. Some observations are made on Canadian mining research efforts, with a view to indicating a more systematic basis of procedure."

Jan 1, 1960

By Janice Zinck, Ian London

In recent years, the secure supply of critical and technology metals has become increasingly important tomajor industrialized economies that seek to sustain their industrial base and develop advanced technologies, such as clean energy. Canada, with its significant reserves of rare earth element (REE) and other metals, has an opportunity to supply some of the global demand for these materials. However, to transition from promising mineral deposits to marketable products, investment in strategic research and development (R&D) and expertise is needed to address the complex technological challenges around the production, separation and processing of these metals, and to better understand the global market for these key commodities. To this end, in its April 2015 budget, the Government of Canada committed to invest $23M over 5 years to accelerate production of REE and chromite/ferrochrome. The goal of this program, developed in close association with industry, is that Canada contributes a sustainable supply of REE to the global market. The research and development program will provide the technological capacity to establish a Canadian REE industry. This paper will discuss REE R&D advances achieved in the first year of the program in areas of mineral characterization, beneficiation, leaching, separation and environmental management and will highlight the Canadian model of collaboration where industry (e.g. prospective producers, technology companies), government, academia and other stakeholders work closely to ensure that the R&D is targeted, innovative and effectively deployed and commercialized.

Jan 1, 2016

By M. J. Young, C. A. Aird

"The Gem molybdenum prospect is situated at the head-waters of Clear creek, between the Fraser river and Harrison lake, about 30 miles north of• Harrison Hot Springs, B.C. Clear creek follows a deeply eroded fault zone southwesterly through the center of the claim group. Elevations range from 2,000 feet in the creek bed up the steep slopes flanking the creek to a height of 5,500 feet. The property lies within an area underlain by schists and gneisses which strike from north to west in a broad fold plunging steeply to the northeast. This metamorphic complex has been invaded by numerous bodies of grano-diorite, much of which is gneissic. A granite plug, roughly 2,400 by 4,000 feet in size, has intruded this broad fold just west of Clear creek and encloses a circular breccia pipe 1,500 feet in diameter. In the breccia pipe, fragments of metamorphic rocks, granite and quartz monzonite porphyry are firmly cemented in a matrix of quartz monzonite porphyry. All the above rocks are cut by numerous fractures filled by vuggy quartz veins, many of which contain molybdenite. Attentien was first drawn to the area by a quartz vein, 18 inches in width, known as the Gem vein, which consists of several laminated bands of quartz and molybdenite. Since 1964, exploration efforts have been directed toward attempting to outline a large, low-grade type of molybdenum deposit."

Jan 1, 1969

By Brien A. Perry, Art Wiebert

"Many organizations which have implemented Total Quality Management (TQM) are finding that the process has either stalled or is not working so well as originally envisioned. This can be particularly evident in an engineering environment where the uniqueness of engineers and their particular culture has not been adequately considered. Winning the commitment of a highly educated group ojprojemnnJJ1s to the TQM concepts, which are often initially 5W2 as too simplistic poses special challenges.Successful TQM implementations are found among technical groups where employees have significant input into creating the new work culture, feel empowered to make changes and are well trained in teamwork. A coach who is knowledgeable in implementation problems can, when working closely with the technical teams, help them circumvent obstacles and guide them successfully through the difficult early phases. The remaining key ingredient for success is supportive management which leads the change and is both informed and appreciative of the accomplishment being made.This Paper is based on first-hand experience with common problems and results encountered in implementing TQM in an engineering environment. Described in the paper are ways of avoiding these problems through awareness of the unique nature of engineering groups, implementation planning, just-in-time training and coaching people in the TQM process. The paper concludes with a focus on the opportunities and results from a successful implementation. These opportunities and results include the benefits each engineer can realize through process thinking, empowerment and teamwork."

Jan 1, 1995

By R. F. Neider, W. R. Bain

"Expanding upon one aspect of a recent paper on ""Fluid Column Roasting at Sherbrooke Metallurgical Co. Ltd.,"" the present paper deals with the operation of the fluid column process to achieve substantial elimination of cadmium and lead during the roasting of pelletized zinc concentrates. Designed to meet the need for additional feed for Matthiessen and Regeler Zinc Company's vertical retort zinc smelter in West Virginia, without recourse to a sintering operation, the plant is capable of simultaneously attaining very low lead and cadmium levels on demand, through operation in the manner described. Fluidizing air admitted via the wind box is supplemented by natural gas admitted via a tuyere bank 15 ins. above the hearth, in quantities adjusted to maintain a reducing atmosphere within the interstices of the bed. In addition, careful attention is paid to bed temperatures, which run from 1,080° to 1,100°C. Under these reducing conditions, 90 per cent of the cadmium and 92 per cent of the lead in the feed are eliminated, the sulphate sulphur content is decreased by 0.5 per cent, sulphide sulphur is held at 0.6 to 0.08 per cent, and the zinc content correspondingly in-creases. The fuel value of the natural gas is recovered as extra steam, which carries a credit. There are some added difficulties with fume accretions, gas conditioning and gas -cleaning, some of which have yet to be overcome."

Jan 1, 1967

By B. S. W. Buffam

"The property of Moneta Porcupine Mines, Limited, consists of a group of eight claims in Tisdale township, Ontario. It includes part of the townsite of the town of Timmins, and adjoins the west boundaries of the Hollin_ger Consolidated and Mace properties. The Moneta property was first staked in 1909, about a year after the first discovery of gold in the Porcupine camp. In 1910 the Moneta Company was incorporated and some preliminary exploratory work performed by Nova Scotia Mines of Cobalt. In 1912 English interests advanced $90,000 for diamond drilling and underground work. One drill hole gave high assays, but apparently the records were poorly kept or the cores were interchanged. As a consequence, when underground exploration was undertaken in 1923 it was directed south rather than west and no ore was found . In 1924 about 5,000 feet of diamond drilling was done in the southern part of the property, but without intersecting ore.In 1931 W. E. Segsworth assumed the direction of the property. Diamond drilling commenced on August 18, 1936. The first hole intersected 9.9 feet of ore averaging 1.23 oz. gold a ton. Underground work was started early in 1937. A mill was erected in the autumn and the first gold brick was poured January 29, 1938.The Moneta mill began operation on January 2, 1938, and the following table gives a summary of the production to June 30, 1943, when the mill was closed."

Jan 1, 1954

By Michael McClintock, Bern Klein

"The high pressure grinding roll (HPGR) is a relatively new comminution technology that is gaining popularity for providing energy efficient solution to hard rock mining operations. A significant barrier to increased adoption of HPGRs is the present requirement for large amounts (excess of 2 tonnes) of sample for pilot testing, which may not be possible for most early stage projects. Three methodologies have been developed at NBK Institute of Mining Engineering at the University of British Columbia that may be used for sizing design optimization of HPGR circuits. All three methodologies use a MTS pistonpress to simulate HPGR comminution. These tests are capable of providing information regarding energy consumption, energy breakage relationship, reduction ratio, and product size distributions. In a period of slow economic development, these methodologies are critical to allow the industry to cost effectively understand the operational benefits of HPGR implementation. This paper examines previous test work done at UBC, as well as the development of an HPGR and piston press database for use in sizing and budgeting of HPGR circuits.INTRODUCTIONCurrently, the mining industry faces several challenges due to falling commodity prices and escalating costs. This has applied pressure for operations and projects to reduce costs and improve project economics. In addition engineering and metallurgical budgets have shrunk as companies try to conserve cash. Improvements and optimization of milling and comminution circuits is one area project economics may be significantly improved. By considering alternative comminution technologies such as the high pressure grinding roll (HPGR), energy operating costs may be greatly lowered. Many have begun to implement HPGR crushing as an alternative to semi-autogenous grinding (SAG) mills, including KGHM and, Sierra Gorda, and Freeport Mc-MoRan’s Cerro Verde operation. However, implementing new technology for companies with little or no HPGR experience may not be practical. An operator must consider both feasibility and economics of a circuit. Currently, consideration of the HPGR requires expensive pilot scale testing for which large sample sizes are needed. In addition, few laboratories are equipped for running pilot scale HPGR test programs. Furthermore, the results of pilot HPGR testing are dependent on the quality of the sample, which cannot represent variations across a deposit. In contrast, ball mills and SAG mills can be sized using the Bond Mill Work Indexes that require a small amount of sample which enable a number of different geological blocks to be tested to allow engineers to have a complete understanding of how the comminution circuit will perform for the life of mine."

Jan 1, 2016

By J. L. Wilson

"Many modern concentrators with VSD driven SAG mills still rely on the control room operator to manually adjust the speed in reaction to increasing bearing pressure. All too often, the problem with this strategy is by the time the operator reacts with a sudden speed increase, the SAG Mill is likely already on its way to loading up. To assist the new operators, the SAG Mill at B2Gold’s Fekola Mine in Mali needed a robust control that could handle load changes and unmeasured disturbances with minimal operator intervention. With modern Distributed Control Systems (DCS) powerful enough to run advanced control, they often have Model Predictive Control (MPC) blocks built in or available as an “add-on” license, and thus MPC can be readily implemented within the modern concentrator with a relatively low added capital cost. This paper discusses an implementation of two single output MPC controllers to control the SAG Mill at Fekola. This was implemented using the existing signals and advanced control blocks available to the installed DCS.INTRODUCTION Many modern concentrators with VSD driven SAG mills still rely on the control room operator to manually adjust the speed in reaction to increasing bearing pressure. All too often, the problem with this strategy is that by the time the operator reacts with a sudden speed increase, the SAG Mill is likely already on its way to loading up. The next step the operator may take may be to cut back the feed rate, or production until the SAG is once again stable. With this sudden reaction comes an abrupt change in SAG rotational speed and power consumption that sends a surge of material down the circuit as the mill suddenly ejects more pulp. Furthermore, choosing a higher rotational speed can lead to higher than normal liner wear as the cataract overshoots the toe of the charge and impacts the liners. After start-up at B2Gold’s Fekola Gold Mine in 2017, the SAG mill was being controlled manually. The SAG rotational speed was adjusted manually by the operator in step changes depending on whether the SAG bearing pressure was increasing, decreasing or stable. During this time of manual control, the SAG fresh feed rate was also adjusted to a tonnage setpoint with a PID controller. Generally, the SAG fresh feed rate setpoint was kept at a target value, but then the feed rate was throttled back if the SAG mill or grinding circuit showed signs of overloading. The extra challenges were that the operators had limited experience and were concurrently learning how the plant operated. Also, they were also occupied with managing situations in the rest of the plant. Often their attention was drawn away from the SAG mill and during that time, the SAG Mill would load up before they could react."

Jan 1, 2019

By G. D. Hibbard

New regions of material property space can be accessed by combining microstructural design at the nm-scale with architectural design at the µm- or mm-scale. In the first case, large strength increases associated with grain size reduction to below 50 nm have driven extensive research efforts into the development of nanocrystalline materials [e.g. 1-3]. For many potential structural applications, however, the density of a nanocrystalline material is just as important as its strength. In fact, reducing the density is more important than increasing the strength for certain weight specific materials performance indices, and it is especially critical for applying structural nanomaterials in the aerospace and automotive sectors. We have developed a new type of structural nanomaterial wherein the effective density of the parent metal is reduced by more than an order of magnitude by incorporating an internal periodic cellular architecture of open space. In one example a low density cellular nanocrystalline material was created by electroforming nanocrystalline Ni around a rapid-prototyped acrylic photopolymer microtruss, Figure 1 [4]. Microtruss materials have periodic cellular architectures that are specifically designed to undergo stretching-dominated deformation as opposed to the bending-dominated deformation in conventional open cell metal foams [5,6]. This new cellular nanocrystalline hybrid material combined the structural efficiency of microtruss architectures with the ultra-high strength that can be achieved by grain size reduction to the nm-scale. Although it played a critical role as a cathode support during the initial stages of nanocrystalline electrodeposition, the polymer core did not contribute significantly to the inelastic buckling resistance of the composite metal/polymer struts and it may therefore be desirable to remove it post deposition by means of chemical dissolution or thermal decomposition [4]. Nanocrystalline electrodeposition can also be used to reinforce conventional cellular metals (Figure 2), creating new types of cellular composites such as metal/metal microtruss hybrids [7-10] and metal/metal foam hybrids [11,12]. For example, nanocrystalline Ni-Fe alloy sleeve thicknesses of up to 400 µm were used to reinforce an aluminum alloy microtruss that had been fabricated using a stretch-bend approach; the nanocrystalline sleeves had the effect of increasing the microtruss strength by up to a factor of twelve and the specific strength by a factor of three [8]. Alternatively, much thinner sleeves can be electroplated to produce structural coatings. In one example, a nanocrystalline Ni coating was designed to provide both corrosion protection and inelastic buckling resistance [10]. Because the ultra-high strength material was optimally located at the furthest distance from the neutral bending axis, only a thin coating of 50 µm was needed to double the inelastic buckling resistance of the 1.13 mm x 0.63 mm cross-section plain carbon steel struts [10]. Overall, the mechanical performance increase that can be obtained through electrodeposition depends on a complex interaction between the starting cellular architecture and the nanocrystalline sleeves.

Jan 1, 2010

By L. M. Nolan

Chemical Mechanical polishing, or CMP, has four components in the polishing interface; namely the polishing pad, the polishing fluid, the abrasives in the fluid, and the surface being polished. Understanding the way that load is transferred between these components is key to understanding and predicting wafer polishing. Numerous models of CMP and the different load sharing arrangements which occur between these four components have been proposed. These include models by Luo and Dornfield (1) and Fu, Chandra and colleagues (2). Other models focus on just one or two loading arrangements, such as `hydroplaning' when all load is transmitted by the liquid in the case of Runnels and Eyman (3). In this work, we consider four possible combinations of load transfer from pad to wafer in CMP. These combinations are listed below in Table 1 and are illustrated schematically in Figure 1. It is important to note the role of scale in this process; the illustrations in Figure 1 are drawn to scale from actual profilometer scans obtained over a length of 5 with particles of 150 nm in diameter. Table 1 - Load Transfer Combinations Load Regime Illustration Wafer - Fluid - Pad Figure la Wafer - Particles/Fluid - Pad Figure lb Wafer - Particles - Pad Figure lc Wafer-Pad Figure ld The interest in load-sharing between the system components is because some configurations are anticipated to achieve higher polishing rates than others. For instance, in hydroplaning, or hydrodynamic lubrication, the lateral force exerted on the polished surface by the particles can be no higher than the fluid shear force developed in the gap between the pad and wafer. This is not expected to generate high rates of material removal from the surface (4). For contact that is largely between the pad and the wafer, such as the regime depicted in Figure ld, the lateral load is transmitted to the wafer by the pad and is hence limited by the pad's low rigidity. This regime is not expected to generate high material removal rates either. The highest levels of material removal are expected from regimes where the mechanical load exerted on the system is transmitted by the particles, in combination with either the fluid or the pad. Under what circumstances does the polishing regime change from one to another? What must occur in order to initiate or terminate contact between the system components? This is an ongoing question in the field of tribology, and has traditionally been viewed in terms of the pressure and velocity applied to the system, the thickness of the fluid film between the two surfaces, and the roughness of those surfaces (4). In this paper, we propose a new mechanism ? that the load on the particles may be sufficient to totally embed them in the polishing pad, at which point they are no longer able to transmit load and polish the wafer surface. This is illustrated schematically in Figure 1(d).

Jan 1, 2010

TIPS FOR SUCCESSFUL WASTE MANAGEMENT ? WASTE MANAGEMENT PLANS ? Define the question to be asked in waste characterization studies ? Calibrate assessments and designs with field conditions ? Ensure consistent with short, medium and long-term mine plans ? Design robust plans - goalposts and expectations will change ? Fully assess and integrate costs into economic models ? Integrate waste specialists into the feasibility and design teams ? Keep it simple and when you can?t, communicate it in simple terms ? PLAN EXECUTION ? Integrate the waste management plan into daily mine operations ? Identify the critical KPI?s , track them and set clear action triggers ? Know the difference between knowledge and data ?make sure you retain knowledge and document the important Maintain management, engineering and operational focus through the mine life

May 1, 2010

By Fabio Mielli

In these times of increasing costs and diminished returns, energy consumption is one source of savings that remains relatively untapped in the mining sector. Typically, 15% to 40% of operational costs can be attributed to energy in mining operations. This ?process variable? is a complex, multi-faceted variable that involves government regulations, societal pressures, cost and competitiveness. A mining company able to successfully embrace an energy efficiency program is more often than not a successful mining company. Production optimization programs, relatively common today, provide increased production, increased availability of assets and, in many cases, improved quality. They generally ignore the energy question altogether. Production Energy Optimization combines reductions in energy consumption with production improvements to reduce the cost per unit of production while improving emissions reporting. An energy strategy in mining and mineral processing operations is a critical component of Production Energy Optimization. This strategy must support the financial and operational integrity of the business. Developing a successful energy strategy requires a well structured approach such as following: ??Understanding where energy is being used and why, ??Recommending and implementing energy conservation measures, ??Driving visibility to targets and results, ??Re-evaluating continuously. The objective of this paper is to help you better understand the process, tools and technologies that enable mining organizations today to address energy and sustainability issues more tactically and proactively.

Aug 1, 2013

By R. Roufail

"Energy consumption in stirred mills has been studied, in the last couple of decades, on a macro scale. Effective operation and meeting particle size required for downstream operations used to be the main objectives behind energy utilization of stirred mills. In this paper, three energy terms are defined to assist in understanding the breakage mechanism for various types of minerals versus mill operation. The types of minerals studied had diverse physical and mechanical properties that are summarized as specific gravity, hardness and crystal structure. The minerals utilized in this study were quartz and galena. The effect of quartz and galena mix has been addressed as well as Lead-Zinc ore sample from SAG mill discharge. The energy input to the mill is function of the agitator speed, therefore three agitator speeds were evaluated, 1000, 1500 and 2000 RPM, respectively. The energy terms studied are specific energy (kWhr/ton). Effective energy is the ratio between net energy and total energy consumed by the mill. Last type of energy is the specific breakage energy, which is the net energy consumed by the mill per one-micron breakage. Results showed that specific energy and specific breakage rate are functions of mineral type, while effective energy is only function of mill input power (agitator speed).INTRODUCTIONGrinding is the largest energy consuming component of a mineral processing operation and typically consumes about 50% of the total energy used at a mining operation (Botin, 2009). Over the last two decades, stirred mills have been extensively utilized in mineral processing operations due to increased mineralogical complexity of ore bodies. Stirred mills grind particles to less than 10 µm by applying a high power intensity. The technology has been the focus of several research studies to investigate mill energy and grinding mechanisms. Becker, et. al. (2001) studied the relationship between different types of energy including input energy, specific energy, volume/mass specific energies, to stress intensity and final product particle size. Other studies such as by Kwade (1999), Kwade and Schwedes (2002), Blecher et al (1996), Partyka and Yan (2007), Stender et al (2004), focused on mill design and/or stress intensity distribution. Peukert (2004) studied the effect of mechanical properties of the grinding media and ground material on the comminution process."

Jan 1, 2016