Search Documents

By Gerald H. Luttrell, Lance Christodoulou, Jaisen N. Kohmuench, Michael J. Mankosa

The efficiency of the froth flotation process has long been known to be strongly dependent on particle size. For sulfide minerals, good recoveries are typically achieved in industrial flotation circuits for particles in the 30 to 200 µm size range. Particles outside this critical size are typically lost in industrial operations and rejected to tailings streams due to inherent constraints associated with the physical interactions that occur in the pulp and froth phases of conventional flotation equipment. In response to these limitations, a series of experimental studies were conducted to determine whether particles previously lost as tailings could be economically recovered using a suite of novel flotation technologies developed for upgrading ultra-coarse and ultra-fine particles in the industrial minerals industry. For the case of ultracoarse particles, a fluidized-bed flotation system called the HydroFloatTM separator was tested. The data obtained using this novel flotation device in both laboratory- and pilot-scale trials showed that good recovery of previously lost sulfide values up to 850 µm diameter could be achieved. Similarly, for ultrafine particles, a high-intensity cavitation-based column cell was tested. This technology, which utilizes highshear contacting of slurry and gas, was capable of recovering valuable ultra-fine sulfide that were previously lost due to the low capture efficiency of conventional flotation processes. The objectives of this article are (i) to describe the unique operating principles of these two advanced flotation technologies and associated ancillary classification equipment, (ii) to present laboratory- and pilot-scale experimental test data showing the metallurgical benefits of the proposed novel flowsheet for sulfide tailings processing, and (iii) to provide a generic cost-benefit analysis of the proposed system for recovering lost values in existing sulfide tailing streams.

Jan 1, 2016

By A. W. Chan

"An interactive computer simulation model of conveyor systems used in oil sands mining has been developed to aid in the selection of mining equipment and the evaluation of operating policies. The materials handling links between supply points, such as bucket-wheel excavators and draglines, and demand points such as bins and extraction plants are modelled in such a way that the conveyor model can be interfaced with any combination of these equipment submodels. Detailed calculations of the power demand of each conveyor section based on operating characteristics and conveyor design parameters are included to permit the close monitoring of energy requirements. Various interactive features are incorporated so that an operator can not only monitor, but also control, the mining operations in the model and experiment with different operating strategies.IntroductionThe interactive simulation model of conveyor systems described in this paper is one of a number of detailed computer models being jointly developed by the National Research Council and Canstar Oil Sands Ltd. on the mining equipment and operations used in oil sands mining. Reference I presents an overview of this whole series of models, their interrelationships and the underlying motivation for their development.A network of conveyors constitutes one of the practical ways for transporting mined material in an oil sands plant. The materials handling links between supply points, such as bucket-wheel excavators, bucket-wheel reclaimers and bins, and demand points such as dumps, bins and extraction plants can be represented by a series of interconnected conveyor sections. For example, the fluctuations of the feed rate at the bucket-wheel excavator, the flow of ore material through the conveyor network and the arrival of this material at the extraction plant can be simulated."

Jan 1, 1982

By W. M. Moon, Hugh G. Miller, C. -S. So

"Digital image processing and enhancement techniques have been applied to airborne gamma ray spectrometry data from Sudbury, Ontario. These results have been correlated and compared with the available geological maps to evaluate their usefulness for identifying lithological units. Digital processing allows the correlation of various data sets, and different combinations of images can be tested and viewed as a composite image. Composite images with pseudocolours provide an opportunity to analyze and correlate information that is not otherwise apparent in individual images. Principal component analysis has been applied to the gamma ray spectrometry data to evaluate their efficacy and relative information contents of the measured and computed data. The results of this study indicate that the combined radioelements image (obtained by combining the radioelement image and the ratio images) is effective for defining areas of relative concentration of a specific element in near surface materials. Furthermore, the composite radioelements image (produced by combining three separate radioelement images) and composite principal components image reflect large-scale lithological variations. IntroductionThe Sudbury area is a unique geological structure located in the southern Canadian Shield (Fig. 1). Because the area hosts economically significant nickel-copper deposits (Pye et al., 1984), it has been surveyed in great detail by geological and geophysical methods. In order to obtain meaningful geological infonnation about the Sudbury area, several studies have been carried out with the application of innovative mathematical techniques for geophysical modelling, and attempts have been made to integrate the multisensor geophysical data available for the area (e.g. Gupta et aI., 1984; Moon et al., 1988; Singh et al., 1993). The main objective of this paper is to apply digital image processing and enhancement techniques to airborne ganuna ray spectrometry data in order to determine their usefulness for regional geological mapping."

Jan 1, 1994

By J. F. Boux

"The study of the total utilization of fly ash has involved all of the known technology in the processing of this waste material into useful products. In addition, a complete knowledge of all the possible uses of fly ash and its products in the market area was probably the most important factor in evaluating the theory and practical feasibility of the total utilization of fly ash from a single large supplyLaboratory tests carried out on the separation of fly ash into different fractions were shown to improve its value and utilization. Four main fractions were studied: a fine pozzolanic low-carbon fraction; a coarse fraction for light-weight aggregate production by pelletizing and sintering; a high-iron fraction; and a carbon-rich fraction. The term ""beneficiation"" here refers to a process of separating fly ash into more useful components.Laboratory and pilot sinter strand tests were employed to optimize the sintering capability and the quality of the heat-hardened pellets through a study of the agglomeration cycle in four principal heat zones, under controlled conditions of air flow, temperature and atmosphere, and including the controlled sizing of pellets.The suitability of the heat-hardened pellets as light-weight aggregate was evaluated in test batches of concrete, which were compared with concrete containing commercial lightweight aggregate of established quality.A study of beneficiated fly ash pozzolan as a partial cementitious binder component in normal and high-temperature cured concrete was reported in a paper at the re-cent Second International Fly Ash Symposium.Samples of raw and beneficiated Lakeview ash were compared with samples of other established high-quality fly ash pozzolans. The evaluation indicated the usefulness of beneficiated Lakeview ash as a pozzolan. Economic studies indicated that to accomplish the primary objective of total utilization of any single source of fly ash (in this case. fly ash from the Lakeview Generating Station, producing approximately 400,000 tons per year), a broad knowledge of the technology of various mineral processes was essential.The design of the fly ash processing plant had to be based on the disposal of all the raw fly ash produced by the generating station. This is contrary to the normal design of a processing plant in which raw materials are supplied and produced according to product demand. The design, therefore, had to be of such flexibility as to pro-duce as wide a variety of products as possible, and the ability to market them had to be well researched and understood."

Jan 1, 1970

By L. H. Chen, Y. C. Chen, Leo Benyamin, W. C. Chen

"To investigate the evolution of fluid-driven fracture of rock-like material subjected to borehole fluid pressure and its consequential damage with regard to post-peak stabilization, micro-seismic activities have been monitored using nondestructive technique of acoustic emission (AE) corresponding to the macro-scale complete history of loading curve by setting the hollow cylindrical external circumferential strain to be a closed-loop feedback signal during servo-fluid-driven tests. Development of a novel fluidinduced loading system injected from internal borehole as well as monitoring system were equipped such that the initiation and propagation of micro-cracks enable to analyze experimentally. By programming/controlling either injection rate or fluid pressure, synthetic sandstones with low-permeability made by cement mortar were conducted in this study. It found that both the growth of macro-crack initialized intensively as reaching the breakdown pressure and the micro-seismic activities represented by AE locations show nice agreement. The experimental results in this paper provide better understandings of fluid-driven fracture mechanism.INTRODUCTIONFluid-driven fracture is a process of generating cracks by injecting viscous fluid into solid material. Conventionally, fluid-driven fracture tests have been performed by mining industry to measure the in situ stress (Haimson & Fairhurst, 1969) and fluid-driven fracture has been employed by the petroleum industry to recover oil and gas. Additionally, the mechanism of crack growth or the extension of existing cracks is important to the evolution of volcanic dikes over distances of a few kilometers (Lister & Kerr, 1991; Rubin, 1995), crack propagation in dams (Bolzon & Cocchetti, 2003) and the disposal of radioactive waste (Sun, 1969)."

Jan 1, 2015

By J. Beland

The Rimouski-Matapedia region is along the southwestern extension of the central Siluro-Devonian synclinorium of Gaspe Peninsula. As in Gaspe about 30,000 feet of Siluro-Devonian strata rest on a "basement" of tightly folded Ordovician rocks. The central synclinorium is divided up into two northeasterly trending belts each of which is characterized by distinctive lithologies and patterns of folding. The northwestern belt is gently to moderately folded and includes lithologies which point to a stable environment. The southeastern belt on the other hand is tightly folded and the lithologies indicate a less stable environment. A marked angular unconformity separates the basement from the Siluro-Devonian cover near the north-western margin of the northwestern belt. At the southeastern margin of the southeastern belt the relationship of cover to basement has not been as-certained because of a fault. The northwestern belt has several features significant in the search for petroleum; the Silurian strata are exposed in broad open anticlines

Jan 1, 1962

By B. Misra, B. S: Sastry, Kollu S. Rao

"This paper reports the results of a finite element study of the geothermal heatflow into dry mine airways. For isotropic and unsteady state conditions the heatflow into mine airways is studied for a range of surface heat transfer coefficients between rock and air, and age of the airway. Dimensionless temperature gradient values are presented in tables for different values of Boit and Fourier numbers and the results are compared with Starfield tables and Gibson algorithm. It is found that Starfield tables have consistently over-predicted the G values with errors ranging from 2% to 10%. The differences between results obtained from the finite element study and the G values calculated from Gibson's approximation method are mapped. The small error values over a large range of Fourier and Biot numbers confirm the suitability of Gibson's algorithm to rapidly calculate G values for estimating the heat transfer from surrounding rock to mine air.IntroductionIn many underground mines heat is a major problem, and the provision of acceptable working conditions requires considerable expenditure on ventilation systems. The rational design and operation of these systems depend upon an understanding of the various sources of heat in the mine. The natural source, i.e. geothermal heat, contributes up to 80% of total heat added to mine air and it is difficult to analyze and predict the heat owing to a number of influencing variables. The problem of geothermal heat flow has been studied by many investigators (Goch, 1940; Starfield, 1966; Hemp, 1987; Amano et al., 1982; McPherson, 1986).The primary concern of this paper is to develop a better ready reference dimensionless transient temperature table for estimating heatflow at any stage of mine airway life."

Jan 1, 1994

By William Petruk, Donald Leroux, Michael Cooper

"Brunswick's primary flotation circuit (CuPb) produces a low grade concentrate containing considerable amounts of undesirable sphalerite and pyrite. To determine the cause of the poor selectivity, a series of Quantitative Mineralogical Analyses (QMA) were performed on several CuPb circuit streams. It was observed that significant fractions of sphalerite and pyrite reporting to the concentrate was liberated, meaning that their depression was not complete. The study highlighted the need for some R&D efforts to be spent in sulphide flotation fundamentals.IntroductionThe viability of many mining projects strongly depends on the performance of their concentrators. More than ever, competitive grade concentrate and high metal recoveries are criteria of paramount economic importance. The selectivity of solid/solid separation processes used in concentrators must be maintained at high levels or continuously improved.Flotation is the solid/solid separation process used by most base metal producers. In spite of its low operating cost, flotation remains a very complex process. To make it selective, precise reagent dosages and electrochemical conditions must be maintained. The difficulty in controlling flotation lies in the numerous heterogeneous reactions that can take place between the different solid, liquid and gaseous phases involved. This complex chemistry makes flotation selectivity difficult to understand and, therefore, to improve from a theoretical point of view.Brunswick Mining and Smelting, near Bathurst N.B., operates a 10500 tpd concentrator which produces four concentrates through five stages of sequential flotation (Figure I). Various reagents are added at key process stages while the ore undergoes different electrochemical conditions. Although the selectivity is important at all stages, the performance of the very first separation, the CuPb circuit, is the most critical. It is here where mineral misplacement to the wrong stream has the greatest economic consequences."

Jan 1, 1996

By M. Myllymäki

"Pre-treatment of mill feed in a minerals processing plant enables for higher production efficiency per ton of product, reduction of consumables and diverting mineral feed types. Sensor based particle sorting allows for pre-concentration of the run-of-mine (ROM) material prior to other concentrating process. Various sensors provide different responses from the minerals in measured particles. The capability of “accepting” or “rejecting” particles based on sensor responses is investigated in specific test work for each project. Modern sorting machines use pneumatic actuators to divert the reject particles from the material stream. This paper discusses the incorporation of ore sorting test work in processing and plant design. When taking the effects of a sorting circuit into account early in the process planning phase, the downstream process can be adequately sized and impacts evaluated. Potential benefits include but are not limited to increased head grade, lower tonnage to the mill, increased mining operations, removal of deleterious elements and changed properties in the process feed. In a case study we present the Keliber lithium project in central Finland. The plant will produce 9000 tons of lithium carbonate per year from a spodumene ore. Ore sorting and flotation tests were carried out in laboratory and pilot scale. Process models were designed and simulations performed using Outotec’s HSC Chemistry Simulation software. Changes in the flotation performance (grade, recovery, impurity levels) were simulated with and without the pre-concentration of the ROM material. The metallurgical performance and mine economics of the different operational scenarios were evaluated using the Ore-Met optimizer module of the simulation software.INTRODUCTION Challenges in the recent years such as declining ore grades, increasing energy prices, scarcity of water and increasing environmental regulations raise the demand for more efficient processing technologies. Sensor based sorting offers a method for pre-concentration or waste rejection at an early process stage. The technology analyzes each rock particle separately for their unique physical and chemical properties, and diverts the particles into separate material streams by high pressure air jets. Successful implementation relies on ore heterogeneity, differential sensor response and suitable feed preparation."

Jan 1, 2018

By W. R. Dodge

THE growth and development of the assay department of the Hollinger Consolidated Gold Mines, Limited, is a similar story to that of the mine itself. As the mine developed and enlarged, so also increased the demands upon this department, necessitating an increase of capacity for fire assaying and a widening of the scope of work to include chemical analysis, metallurgical tests, research, and screen analysis. The yearly total of determinations, taking an average for the past six years, is approximately 350,000. The major portion of this figure represents fire assaying for gold and silver, being approximately 950 fire assays per day. The assay department occupies the ground floor of the administration building and covers approximately 4,000 square feet of floor space. Ready access is had by motor truck and electric railway for the delivery of samples and the removal of crushed rock and rubbish. The combined weight of all sample rejects amounts to about 5,000 lb. per day, which is sent to the mill bins. There are six departments, each occupying a separate room-grinder room, fluxing room, furnace room, parting room, weighing room, and flux-mixing and storage room.

Jan 1, 1931

By M. Lahtinen, B. Saxén, M. Latva-Kokko

The conventional jarosite precipitation process with neutralization by zinc calcine is widely utilized in the zinc industry. However, it has a significant drawback of causing losses of valuable metals like zinc, lead and silver to the jarosite. This comes mainly from the content of these metals in the calcine used for neutralization. As the zinc plants today want to maximize metal recoveries and minimize the amount of residues, this matter has become more and more relevant for zinc producers. Outotec developed and patented in early 2000 an improved version of the jarosite precipitation process in which the need for neutralization can be minimized, thus the metal losses to the jarosite also can be minimized. At the same time, the iron content of the jarosite increases and the amount of produced jarosite is smaller. The main feature of this process is to start the precipitation from ferrous iron after having reduced all the iron by zinc concentrate in a separate step before jarosite precipitation. Iron is then oxidised back to the ferric form simultaneously with jarosite precipitation. By this method, the formation of sulphuric acid is only half that compared to the conventional method and the need for calcine for neutralization can be avoided. High mixing and oxygen dispersion capability are needed in this jarosite precipitation process. Such capabilities are found in the Outotec OKTOP® reactor series. High performance reactors are not only needed to generate high quality precipitates, but also to maximize oxygen utilization; i.e., to minimize operation costs. Outotec’s latest development in this area is the OKTOP® plant product in which not only the reactors, but also all the accessories are designed, manufactured and delivered by Outotec. One responsible supplier ensures efficient and fast delivery and can provide mechanical and performance guarantees for the entire plant unit.

Jan 1, 2016

By Sadan Kelebek, Gerhard W. Heinrich, Peter F. Wells, Peter J. Whittaker

"Based on plant mineralogical data & circuit modelling, a pilot plant campaign was conducted at Strathcona Mill to identify options for improving the performance and operating flexibility of the copper-nickel separation circuits. Emphasis was given to options for combined treatment of the two feed streams (primary nickel ore rougher concentrate and copper ore circuit concentrate) to obtain more flexibility in the use of existing column flotation capacities. The pilot test results demonstrated that circuits which incorporated preconcentration prior to column flotation gave the best metallurgical results. Maximum column carrying rates were also related to the preconcentration. Predictions that increased circulating loads from the column scavengers would improve copper-nickel separation performance were confirmed.IntroductionThe copper-nickel separation circuits at Falconbridge's Strathcona Mill produce a high grade (>30% Cu) copper concentrate most of which is treated at the Falconbridge Kidd Creek smelter near Timmins. The remaining nickel concentrate which still contains approximately 20% of the feed copper is combined with other lower grade nickel/copper concentrates and shipped to the Falconbridge nickel smelter. The separation is required because of the limited capacity for copper processing in and downstream from the nickel smelter. Since no nickel is recovered at present in the Kidd smelter, the challenge is to minimize the nickel content of the copper concentrate.At present there are two independent separation circuits treating the rougher concentrates from the copper and nickel circuits as shown in Figure I. The minerals treated are mainly chalcopyrite and pentlandite but there is up to 25% of the copper present as cubanite in the copper ore. The circuits were kept separate because the flotation rates and froth characteristics were very different, probably because of the presence of cubanite and the large difference in the concentrate grades feeding the circuits."

Jan 1, 1995

By A. Baydusa, K. Barron

A theory for cutter roof failure in coal mines has been developed. It is shown that the key parameters influencing the likelihood of cutter roof failure are the rock strength, the vertical stress (depth) and the horizontal to vertical stress ratio. The support force necessary to prevent the development of this mode of failure is, in most cases, so high as to make it impractical to apply a force of such magnitude. It is, therefore, better to allow the failure to occur and to design a bolting system to support the dead weight load of the failed block. This is probably best achieved by using a yielding bolt system (such as split set bolts) which is anchored well beyond the top of the potential failure block. The maximum potential caving height determined from this theoretical approach compares favourably with field observations reported in the literature.

Jan 1, 1999

By G. Heinrich

Size by size recoveries and pentlandite liberation data from image analysis were used to evaluate plant tests of pentlandite flotation and pentlandite/pyrrhotite middlings flotation from pyrrhotite in a circuit treating low grade magnetic intermediates at the Strathcona Mill. Raising the pH with lime gave improved selectivity for liberated pentlandite but there were major losses of middlings unless the circuit was pulled hard indicating the need for finer regrinding. However, size by size recoveries at the normal regrind showed that, while the pentlandite recovery improved in the finer ranges, the pyrrhotite recovery also increased leading to little selectivity in any size range. A much finer regrind gave greatly improved selectivity in all size classes suggesting that 'surface polishing' as well as liberation effects were being seen. Using liberation data from image analysis of the products, surface polishing accounted for over 99 % of the improvement in selectivity. Unreasonable recoveries of more highly liberated particles were observed for liberation analysis by volume fraction but showed the expected trend in recovery when the analysis was based on surface liberation. The surface liberation data showed that the improved pentlandite recoveries after finer regrinding were to more than 90 % caused by improved liberation with the remainder contributed by surface polishing effects. The practical implications of this work are that i) the comparison of particle grades with product grades allows to estimate the effect of regrinding on co-flotation/entrainment, ii) surface liberation models should be used for evaluating recoverabilities by flotation and iii) regrind circuits may be set up to ensure that all particles go through the mill or that only the coarse fraction is reground depending on the surface scrubbing found to be required.

Jan 1, 1993

By J. Keough

During industrial electrowinning of copper, uneven growth can impact current efficiency, cause short-circuits in the cell and negatively impact the final quality of the metal product. Copper electrodeposits can be made smoother by incorporating a host of additives in the electrolyte but uneven copper growth may still occur due to variations in electrolyte composition throughout the cell-house. To quantify roughness, 3D images of the surface may be combined with scaling analysis to gain further insight into the deposit structure. Moreover, scaling analysis may offer a method to predict long-term deposit structure using short-term copper deposits. In this paper, the application of Atomic Force Microscopy (AFM) and scaling analysis are used to monitor copper growth and extract surface roughness characteristics. The cathode was a 304 stainless steel disc that was polished to a mirror finish. Copper was deposited onto this surface over a range of 10, 20 and 30 minutes from an acidic sulfate solution (40 g/L Cu) at 40oC from an electrolyte that contained or was free of guar. AFM images were acquired to obtain 3D topographical information on the samples and scaling analysis was performed to extract the root-mean-squared (rms) roughness, periodicity (grain size), aspect ratio of surface features and growth mechanism. INTRODUCTION During the process of copper electrowinning, the dissolved metal ions are reduced and thereby deposited onto a cathode substrate which is later recovered by stripping the metal from the cathode surface. Although this process is widely used in the industry, the conditions of the deposition procedure may cause the growth of the metal product to be uneven which can not only impact the current efficiency and final copper product quality but may also lead to plant interruptions through short-circuits if the anode and cathode make contact. To create more uniform copper deposits, a host of additives may be included in the electrolyte which may act as brighteners, leveling agents and inhibitors which may include guar gum, glue, thiourea or polysaccharides or polyacrylamides and their industrial use has changed over time (Moats, Luyima, & Cui, 2015). As such, the electrolyte composition is often complex and subtle variations in the solution matrix throughout the cell-house may impact the surface morphology of the final copper product. In an effort to quantify the roughness of copper samples, image analysis is often applied and may include Scanning Electron Microscopy (SEM) or Atomic Force Microscopy characterization. While both are appropriate, AFM offers 3-dimensional information which may be used to both qualitatively and quantitatively characterize the surface characteristics.

Jan 1, 2019

By Yan-Jun Shen

The rock mass classification system, BQ (basic quality), is the only national system that is suitable to most kinds of rock engineering in China. It uses two main aspects of the rock mass, the intact uniaxial compressive strength (UCS) and the rock intactness index (KV), to obtain the rock mass BQ. The index KV could be measured by the acoustic wave method. However, because this method is an indirect approach to characterize the rock mass structure, misfits often occur between the test results and the actual rock mass characteristics. Therefore, a new parameter KGSI expressed by the geological strength index is proposed to replace the original KV, and a new method is presented to express the value of BQ as a function of the UCS and the KGSI. Then, the underground excavations at five hydropower stations were chosen as examples to study the relationship between the revised BQ and the each of the international systems (RMR, Q or RMi). In addition, the applicability of the RMR, Q, or RMi system is discussed for China?s rock characteristics and geological conditions, and suggestions are given for improving the revised BQ system.

Aug 1, 2013

By J. H. Pateson, D. C. Comrie, D. J. Ritcey

"Geopolymers are inorganic semi-amorphous three dimensional silico-aluminates of the poly(sialate) type (-Si-O-Al-0-) or of the poly(sialate-siloxo) type (-Si-O-Al-O-Si-0-). Polycondensation occurs at low temperatures with geopolymers being stable up to 12oo0 c. Research, development and application technology pertaining to geopolymers is being undertaken jointly with Dr. Joseph Davidovits of The Institute for Applied Archaeological Sciences of Florida, U.S.A. This joint focused upon the chemical Barry University in Miami Shores, research and development program has stabilization and solidification of various waste products through geopolymerization. Of particular interest is the geopolymerization of mine wastes including tailings and waste rock derived from the processing of base metals, precious metals, potash, coal and uranium deposits.INTRODUCTIOND. Comrie Consulting Ltd., in cooperation and technical liaison with CANMET, Ottawa has been testing the application of geopolymers to mining wastes. Corporate efforts to date have concentrated upon reactive acid tailings, principally from the abandoned Kam-Kotia Mine site, and dewatered paint waste sludges. Test work conducted to date has successfully yielded geopolymer treated materials and wastes with increased chemical and structural stability. Wastes containing heavy metals, cyanides, arsenic and sulphur dioxide have been successfully geopolymerized."

Jan 1, 1988

By H. E. T. Haultain

Research is a much over-overworked word, sometimes a much abused word; the result of this has been that many who really need the word avoid it, shy away from it just as we do from that most useful word camouflage. We have not been altogether happy in our substitutes. Some years ago I spoilt a very good proposition by using the word investigation. There were those who thought that men and methods were to be investigated instead of simply processes. They expected disruption instead of co-ordination. The bad psychology up-set the scheme. The word experiment is even worse in its psychology. To the mind of the "practical" business man experiment denotes ignorance, waste of time and money and presupposes failure. It is not so long ago that the recognized way of improving the methods about a mine was to get a new manager. Until comparatively recently the average life of a boss in a mine in the West was under, rather than over, two years. Certainly was this the case in the smaller mines. Directors did not recognize that a cock-sure new boss was a greater experiment than a certain amount of feeling-his-way on the part of the old one. We always say that no two mines are the same but we are only now realizing to what extent the fine points of the game can and must be learnt on the job itself. One of the main differences between a small property and a large one lies in this study of the fine points of the game. In the early stages operation is the main point-get her going and keep her going.

Jan 1, 1924

By M. Askari, M. H. Parsa, S. Kashani-Nejad

Sarcheshmeh refractory consumption rate is about 7.5 - 8 kg/ton of the produced copper, which is almost three times higher than the other smelters practice. High destruction rate of tuyere zone refractory controls vessel productivity and operational lifetime. In this research with the aid of cold model and computational fluid dynamic (CFD), melt recirculation pattern and gas - liquid plume properties in the wide range of gas blowing conditions were studied. Results revealed that in addition to the well-known mechanical refractory destruction mechanism, fast tuyere zone refractory destruction could also be related to the cold bubble cluster formation near tuyere tips and introducing severe thermal shock to the refractory surface. Removing accretion and its strong bonds to the refractories around tuyere tip, causes refractory mechanical destruction and increases tuyere diameter. Increased tuyere diameter, in turn assists gas discharge in the bubbling regime. Air blowing in the bubbling regime result in the formation of big bubble clusters, bubble breakup and back attack occurrence which all found to have major impact on the refractory lifetime. Outcomes of this research, contributed to the plant converting management, blowing hardware and instrumentation improvement.

Jan 1, 2004

By C. Bernier

This paper deals with three major problems associated with mining operations during the winter. These are the maintenance of the cooling systems of diesel engines, the high incidence of hydraulic dump failures on packaging machines, and the build-up of frozen fines on wet-ore conveyor belts.

Jan 1, 1966