Search Documents

By Colleagues from Process and Operation departments, Guy Chevalier

"QCM's pellet plant, located in Port-Cartier, Quebec, produces up to 8.6 million tons of iron ore pellets annually. Four different types are produced: three for blast furnace operations and one for direct reduction furnaces. The paper presents the scientific approach that led to the installation of new process equipment to improve the reducibility of direct reduction pellets (DR pellet). The findings, the equipment selection and some post start-up modifications are presented.This low silica DR pellet is used in Midrex and HyL shaft furnaces. A good DR pellet has to meet strict chemical, physical and metallurgical specifications. An important metallurgical property is its ability to release oxygen when exposed to reducing gases. Considering that the market for DR pellets is expanding and being aware that reducibility is critical for our clients, a program to improve the latter was undertaken. Test work showed that one factor which has a negative effect on reducibility is the proportion of particles larger than 75 microns. Knowing that the best way to reduce the amount of coarse particles was to close our open grinding circuits, we began evaluating the most suitable classification equipment applicable to our process operations. We settled on hydro-classifiers based on their very sharp cut and their low operating costs. In light of the hydro-classifiers performance it was also decided to replace the hydro-cyclones of an already closed circuit.INTRODUCTIONAt the Québec Cartier Mining pellet plant, continuous improvement programs are aimed at increasing levels of consistency and improved chemical, physical and metallurgical properties. This is being accomplished while still maintaining pellet plant production volumes to satisfy market demands.QCM produces three types of pellets for blast furnace use: acid pellets, designated as ""BHF"", fluxed pellets, designated as ""BAF"", and low silica fluxed pellets, designated as ""BSA"". For direct reduction, a low silica acid pellet or DR pellet, designated as ""BBS"" is produced. This low silica DR pellet is used in Midrex and HyL shaft furnaces.The demand for DR pellets has been increasing during the last few years and is believed to continue so in the future. Wanting to be present in this growing market QCM found that it would be essential to work at improving its DR pellets quality. Efforts have been focused on improvements in three areas: SiO2 reduction, elimination of sticking and increasing reducibility. Improvement programs have begun with laboratory research followed by plant trials and full-scale implementation as a cooperative effort among QCM, COREM, and key customers."

Jan 1, 2002

By C. R. Hocott

"IntroductionRESEARCH in petroleum production consists primarily in investigations related to the drilling for and recovery of oil. As an organized activity of individual oil companies, production research is now 30 to 35 years old, and the petroleum industry may point with justifiable pride to the achievements of this third of a •century. Emphasis on research has grown through the years until at the present time many of the larger companies operating in the United States •have well-organized production research staffs.In addition to the efforts of the oil companies, significant research and development in petroleum production technology have been performed by oilfield service companies and others. Valuable contributions have been made through fundamental research carried on by the U. S. Bureau of Mines and by various colleges and universities, both in their own programmes and in programmes sponsored by industry, such as those of the American Petroleum Institute. However, the total effort of these groups is small when compared to the sum of the effort devoted to research by the individual .oil companies. In contrast to some industries which conduct the major portion of their research through co-operative, sponsored research at universities or research institutions, research by the petroleum industry is done predominantly by individual company research staffs. These industrial research groups have usually been organized in such a way as to provide liaison and co-ordination with operating technical staffs. In this way, the research groups are kept aware of the major problems confronting the operating departments and, correspondingly, the operating technical people •are able to keep informed on research activity and progress. This type of close contact generally results in prompt testing of research developments in actual operations."

Jan 1, 1953

By G. B. Harris, C. W. White

Cyanide has been used for the recovery of gold since the mid 1800s, but several jurisdictions have already banned its use, and environmental pressures are increasing to finding an alternative. Gold also forms chloride complexes similar to those of cyanide, but the use of chloride has never achieved widespread acceptance. This paper describes a chloride-based flowsheet, wherein the key unit process is the recovery and recycle of chloride ion. It is shown that the chloride-based flowsheet is competitive economically with the conventional cyanide-based flowsheets, and that it has a number of other advantages, particularly environmentally.

Jan 1, 2011

By Hevina S. Dashwood

This paper proposes to build on my previous research (Dashwood 2012), which analyzed how and why the norm of sustainable development became institutionalized in the global collaborative corporate social responsibility (CSR) initiatives of major mining companies. Since the late 1990s, the majority of major global mining companies have employed the norm of sustainable development to frame their individual CSR policies and to inform industry collaboration at the global level through the International Council on Mining and Metals (ICMM). This paper proposal seeks to address lingering questions from that research, by developing an explanation for how the normative frame of sustainable development has translated into specific CSR standards adopted by the mining industry. Preliminary findings suggest that, although the global mining industry has reached broad consensus on the meaning of sustainable development in the context of mining, there remains considerable variation between mining companies in terms of which specific global standards they adopt. As members of the ICMM, major mining companies are required to report according to the Global Reporting Initiative (GRI) indicators relevant to mining, and there has been wide-spread up-take of the ISO 14,001 environmental management system standard. However, other global standards, such as the International Finance Corporation (IFC) Performance Standards and the Extractive Industry Transparency Initiative, have not been uniformly adopted by the mining industry. What explains this variation? The paper employs a three-level institutional framework (rational choice institutionalism, historical institutionalism and the ?new? institutionalism in organization theory) to explain the influences on the adoption of CSR standards in the global mining sector. Existing research confirms that institutional context is an important factor in explaining CSR adoption in the mining sector (Dashwood 2012). Are similar forces at work in explaining the variation in adoption of specific CSR standards? A three-level institutional analysis lends itself to uncovering influences both external to mining companies (such as pressures from stakeholders), as well as internal company dynamics (such as managerial discretion). Furthermore, the framework can incorporate dynamics operating at the global level (such as isomorphism), the national level (such as the regulatory regime) and the local level (such as community needs and environmental challenges). The theoretical significance of this framework is that the influences on CSR adoption are more complex than can be explained in a single approach (such as narrow rational choice/cost benefit explanations). On a practical level, insights into how global standards get interpreted and acted upon by individual companies could lead to the development of more appropriate and effective global standards.

Aug 1, 2013

By G. R. Cope, C. D. Spence

"The Mac porphyry molybdenum prospect is located 100 km east of Smithers in central British Columbia. The identification of anomalous levels of molybdenum, copper, and silver in three adjacent lakes, sampled during a regional lake sediment survey, lead to the discovery of molybdenite mineralization in float. Subsequent magnetic and soil geochemistry surveys, together with prospecting and mapping, located the source of the float. Mineralization is hosted by a leucocratic granite stock of the Upper Jurassic to Lower Cretaceous Francois Lake Intrusions which has intruded Carboniferous and Permian Cache Creek Group volcanic and sedimentary rocks. The stock measures 500 m by 300m at surface and is mineralized throughout. Sulphide mineralogy is simple and consists of molybdenite with minor pyrite and local chalcopyrite. Molybdenite occurs within fractures and as selvages along quartz stockwork veins and is best developed near the margins of the stock.Known mineralization is coincident with distinct soil geochemistry and magnetic anomalies. Two additional areas of the property display similar features and these remain to be tested.IntroductionThe Mac property is situated in the Babine Lake area of central British Columbia on NTS map sheet 93K/13E, approximately 100 km east of the town of Smithers (Fig. 1). The property lies on the western margin of the Hogem Range at the northern tip of the Nechako Plateau. The centre of the claim block lies at 54°51 ' 30""N and 125 °34 '30""W.Topographically, the claims are characterized by gently rolling hills ranging in elevation from 900 m to 1500 m. Slopes are forested with tall conifers and underbrush is minimal. Flat-lying areas are swampy with tall grasses and scrub brush.Presently, the property is only accessible by helicopter from bases located in Smithers and Fort St. James. Recent road construction by the British Columbia Forest Service has brought road access from Burns Lake to within 5 km due south of the property. It is expected that in the near future, roads will be advanced into the claim area to facilitate logging of mature timber."

Jan 1, 1995

By A. Hashempour, D. Javani

"Selection of an optimal bit is a critical issue in drilling engineering. Specific energy (SE) and Cost per Foot (CPF) are the most common methods for evaluation of bit efficiency and optimal bit selection. The major shortfall of both methods is that they do not directly account for geological and geomechanical parameters of formations being drilling. In this paper, results of using the two foregoing methods are compared using Formation Drillability (FD) method, which directly accounts for geological and geomechanical parameters of a formation. This method combines various geological and geomechanical parameters and yields a dimensionless parameter indicating the formation drilling hardness (drillability). Results of this study show that the amount of energy, cost and time spent for drilling a unit volume / length of an identical formation may vary in different wells. This is due to the fact that geological and geomechanical characteristics of a formation may vary among wells and even within short intervals of a single well. Therefore, an optimal bit may not be appropriately selected, if drilling and economical parameters are the only factors considered and the formation geological and geomechanical specifications are ignored.INTRODUCTIONMany authors such as Bilgesu, Al-Rashidi, Aminian, and Ameri (2000) and Clegg (2006) conducted research in the evaluation of bit performance and optimum bit selection. Almost all of them tried to establish a good relationship based on geomechanical parameters. Primary examples are the research done by Ubaldi (1999), Macini, Magagni, Da Dalt, and Valente (2007)."

Jan 1, 2015

By M. Gimpel, R. Galler, T. Antretter, H. Kargl, R. Tichy, W. Ecker, M. J. Mikl-Resch, G. Pittino

"A computational method based on a continuum-mechanical approach to simulate rock cutting is developed and evaluated. The aim is to obtain the local loading acting at the cutting pick during operation. The explicit FEM is chosen to model the pick-rock interaction. The presented method takes advantage of (i) an advanced material model (ii) a robust contact algorithm and (iii) fast calculations due to parallelization. A damage-plasticity law is chosen and modified with user-subroutines. A user integrated element deletion routine evades critical mesh distortions. Infinite elements at the model boundaries avoid unrealistic deformation wave reflection.INTRODUCTIONExcavation in mining and tunneling is a costly and complex process. Special equipment such as the roadheader (Figure 1) is employed to cut the rock in the excavation process but high material strengths limit their usability (Tockner 1999). Nowadays a challenge is to extend their field of application to harder and more abrasive rock materials. The forces on the pick (Figure 2) are of great importance and determine wear and especially the efficiency of the machine. Figure 2 shows the principle of cutting and the predominant forces. The variation of pick geometry, cutting depth or attack angle will result in an alteration of these forces and determine the efficiency of the process (Tockner 1999). The mechanisms of rock cutting follow the principle of indentation (Kou et al. 1999). Directly under the indenter a hydrostatic stress state evolves causing the material to fail only due to crushing and fragmentation mechanisms. In the close surroundings large strains emerge and tensile cracks are formed but in a further distance the material behaves elastically."

Jan 1, 2015

By M. Gimpel, R. Galler, T. Antretter, H. Kargl, M. Mikl-Resch, R. Tichy, W. Ecker, G. Pittino

"A computational method based on a continuum-mechanical approach to simulate rock cutting is developed and evaluated. The aim is to obtain the local loading acting at the cutting pick during operation. The explicit FEM is chosen to model the pick-rock interaction. The presented method takes advantage of (i) an advanced material model (ii) a robust contact algorithm and (iii) fast calculations due to parallelization. A damage-plasticity law is chosen and modified with user-subroutines. A user integrated element deletion routine evades critical mesh distortions. Infinite elements at the model boundaries avoid unrealistic deformation wave reflection.INTRODUCTIONExcavation in mining and tunneling is a costly and complex process. Special equipment such as the roadheader (fig. 1) is employed to cut the rock in the excavation process but high material strengths limit their usability (Tockner 1999). Nowadays a challenge is to extend their field of application to harder and more abrasive rock materials. The forces on the pick (fig. 2) are of great importance and determine wear and especially the efficiency of the machine. Figure 2 shows the principle of cutting and the predominant forces. The variation of pick geometry, cutting depth or attack angle will result in an alteration of these forces and determine the efficiency of the process (Tockner 1999). The mechanisms of rock cutting follow the principle of indentation (Kou et al. 1999). Directly under the indenter a hydrostatic stress state evolves causing the material to fail only due to crushing and fragmentation mechanisms. In the close surroundings large strains emerge and tensile cracks are formed but in a further distance the material behaves elastically."

Jan 1, 2015

By R. D. Prettie

Wood preservation may be defined as the art of protecting wood from decay. In its broadest sense, however, it includes a much wider field. It might be more properly de-fined as the art of protecting wood from destructive agents, such as decay, insects, marine borers, mechanical wear, etc. The earliest data on record for the preservation of organic bodies is found in Egyptian manuscripts. The bodies which we call mummies were impregnated with antiseptics, of which the principal were natrum (sodium sesqui-carbonate), sodium chloride, and sodium sulphate. After being steeped in the solution, they were subjected to either a boiling or baking process in a bituminous preparation. The first attempts in Europe to preserve timber were made by the Greeks and Romans. They extracted essential oils from the juniper and cypress trees, and either rubbed these oils into the wood they wished to preserve, or bored thousands of small holes in the wood and poured the preservative oil into the holes. The famous statues of Jupiter and Diana were carved out of wood. The ceremony of pouring in the preservative oil by the High Priests was a religious pageant of great importance, of which there are many records.

Jan 1, 1926

By M. L. Wacker

"Cigar Lake high-grade uranium mine in Saskatchewan is operating after 25 years of test mining, construction, and mine flood remediation. Factors include ground stability, groundwater control, radiation exposure, and ore handling. A 10 year test program resulted in validating “jet boring”, a non-entry mining method involving artificially freezing the orebody and surrounding rock; tunnelling to develop access crosscuts below the orebody; installing cased pilot holes through ore; extracting ore using rotating high-pressure water jets within pilot holes; and cavity concrete backfilling. Ore slurry is prepared underground, pumped to surface, and trucked to McClean Lake mill for processing to uranium concentrate.RÉSUMÉ Après 25 années d’essais sur les méthodes minières, de construction et d’assainissement suivant les inondations à la mine, l’exploitation de minerai à haute teneur en uranium Cigar Lake, localisée dans la province de la Saskatchewan, est opérationnelle. Les principales difficultés concernent la stabilité du terrain, le contrôle des eaux souterraines, l’exposition aux rayonnements et la manutention du minerai. Un programme d’essai de 10 ans a abouti à la validation du « forage à érosion », une méthode minière qui consiste à congeler artificiellement le corps minéralisé et les roches environnantes ; à creuser des tunnels pour développer des travers-bancs d’accès en dessous du corps minéralisé ; à installer des puits de fondation pilotes à travers le minerai ; à extraire le minerai à l’aide de jets d’eau à haute pression dans les puits pilotes ; et à remblayer les cavités avec du béton. La boue de minerai est préparée sous terre, pompée vers la surface puis transportée par camion jusqu’à l’usine de concentration de McClean Lake pour le traitement afin d’obtenir du concentré d’uranium.INTRODUCTIONThe Cigar Lake deposit is in northern Saskatchewan, 660 km north of Saskatoon, Saskatchewan, Canada, at the east edge of the Athabasca basin (Figure 1; Bishop, Mainville, & Yesnik, 2016). The operation is jointly owned by Cameco Corporation, AREVA Resources Canada Inc., Idemitsu Canada Resources Ltd., and TEPCO Resources Inc. Cameco has been the operator of Cigar Lake since January 2002. The discovery hole was drilled in 1981. Commercial production was declared in May 2015 and the Phase 1 operation will have a mine life of 15 years."

Jan 1, 2017

By W. H. Moore

It seems necessary, at times, that we should reconsider some of the more obscure causes that lead to explosions of gas and coal-dust in mines, in the hope that a recapitulation will keep before us that old and true saying "eternal vigilance is the price of safety". This explosion, while not extensive (resulting in only two much to be regretted deaths) enlarged our vision as to the possibility and probability of other explosions with more disastrous results. As this is only a partial report I shall have to omit many things that are generally included in describing a mine explosion. The mine was worked exclusively with electric cap-lamps -only firebosses and other officials carried safety-lamps. All shots were examined and fired by firebosses with a small hand-battery. Monobel was used exclusively for blasting, and clay for tamping. The system of haulage iri use was main-rope and winches, horses being employed for gathering. Compressed-air was the motive power for all winches and pumps, excepting the pumps at the shaft-bottom which were steam-driven. The mine was wet with practically no dust anywhere, except what was being made at the coal-face in the getting of the coal. Gas was found occasionally, generally in the brushing, especially where the brushing was carried up to a small seam, 2 to 6 feet above the main seam. The place where the explosion took place was known as Leigh's heading, which was being driven to the rise, immediately inbye of the siding (off No. 1 left, off the new slope) and was about 90 feet up from the level.

Jan 1, 1926

By H. A. Wilson

Introduction Salt (sodium chloride) occurs naturally either in the solid state as rock salt or in solution as a component of natural brines. It is the major saline constituent of sea water, which contains about 4 percent salt-roughly 164 million tons, or enough to meet world salt demands for five years, per cubic mile. The great rock salt deposits of the world are generally regarded as having been formed by the evaporation of sea water over long periods of rime in wholly, partially, or periodically cut-off bays of ancient oceans. History and Occurrence of Salt in Canada We can speak today of the vastness of Canada's salt resources, but it was not always so. Settlement of our Atlantic seaboard and the Sr. Lawrence valley began in earnest in the early 1600's. The first small commercial salt works in Canada did not come into operation until 1866. Thus, for some two and a half centuries, the inhabitants of this growing country were entirely dependent on foreign sources for every pound of salt they consumed. The record shows that from at !east 1800 onward, the need for a domestic salt industry was clearly recognized by the governments of the day. It was during the Western Ontario oil-boom of 1866 that the initial discovery of rock salt in Canada was made, not far from Goderich, at a depth of 1,000 feet. A salt company was promptly organized, and with their operations there began the gradual and still uncompleted conquest of the Canadian salt market by the Canadian salt industry. Over the next thirty years many holes were drilled into the Salina formation both in Ontario and Michigan, and encountered rock salt. A vast salt-basin was disclosed, approximately outlined, and given the name Ontario-Michigan Salt Basin. The Ontario portion of the basin extends over at least 3,500 square miles, is met with at a depth varying between 800 and 1,600 feet, and has a thickness of 50 to 250 feet. No attempt has ever been made, so far as we know, to calculate the total salt reserves of this basin, but the minimum indicated in the Ontario portion by the figures just cited is just under thirty-five cubic miles. The specific gravity of rock salt is 2.2. From these data, those so inclined may calculate the tonnage.

Jan 1, 1947

By V. Taylor

"THE petroleum industry in Canada has been experiencing considerable difficulty in filling its manpower requirements during the last few years, and because of the rapidly expanding nature of the industry it is concerned about the supply that will be available to fill the needs of the future. As the oil industry is one of the more technically oriented industries, the most acute problem exists primarily in the field of profession-al/technical personnel. This is particularly true in the production and exploration side of the business, because it employs the highest percentage of this type of personnel. Let me illustrate this by giving you some figures reported by the Alberta Bureau of Statistics as of December, 1965 -out of a total of 9,641 male employees engaged in oil producing and geological and geophysical operations in Alberta, 3,021, or 31 per cent, were classified as engineers, geologists, geophysicists, managers and other professional personnel. No figures are available for 1946 to make a direct comparison of the expansion of the industry over the past twenty 466 years, but it is doubtful whether more than 100 professional/technical people were engaged in producing in Alberta at that time"

Jan 1, 1967

By B. McHenry, A. E. Wraith, P. J. Mackey

The Wallaroo smelter on the Yorke Peninsula, South Australia commenced smelting operations in 1861 treating ores from the nearby Moonta and Kadina mines. The plant expanded and modernized on several occasions and was a leader in the successful introduction of new technology to improve operations. It operated continuously until 1923 when local mines became exhausted; in the closing stages of the 19th century it was the largest copper smelter in the world outside of those in Swansea, Wales. In 1892 a small electrolytic refinery was established at Wallaroo, the first in Australia, based on principles developed by Elkington at Pembrey, Wales in 1869. The Wallaroo refinery was specifically built to recover gold and silver from copper produced by smelting gold-containing feed materials shipped from Western Australia. This first venture into electrolytic refining was replaced in 1903 by a somewhat larger refinery which, although modest in size for its time, with a capacity of about 1000 tonnes of cathode copper per year, was very productive in precious metals. Anode copper was produced by an updated version of the reverberatory-based Welsh process until 1910 when barrel-type pneumatic converters were introduced based on American practice; subsequently, anodes were cast by tapping the precious-metals rich "bottoms" portion of converter copper as produced at about one-fifth into the copper blow. The present paper describes the Wallaroo refinery, its anode supply and products, supported by initial observations on a sample of a Wallaroo cathode held in the collection of the South Australia Museum, Adelaide SA, Australia. INTRODUCTION Australia ranked 6th in the world for copper mine production in 2018, with an output of 918,000 tonnes of mined copper, after Chile, Peru, Congo, China and the USA; about 40% of Australian mined copper was smelted in the country. Interestingly, the world ranking of Australia in mined copper has, with a few variations, remained about the same for more than 100 years – of interest, it was also the 6th largest country for copper production at 21,089 tonnes in 1899. At that time, all or most of the copper was smelted in the country (Mackey, 2016). Copper was first discovered in Australia in 1842 in South Australia not far from Adelaide; additional copper discoveries in the region soon followed. At first, copper ore was shipped to Swansea, Wales for smelting (Bampton, 2003). However, in addition to the long, 150 day one-way sea passage, it seems Welsh smelters preferred higher grade of ores – these aspects and likely a mood in the new colony to be independent of Swansea (Evans, 2014) evidently encouraged local smelting at the mine sites using small, Welsh-type reverberatory furnaces fired with hardwood as fuel and operated by Welsh and Cornish migrants. The first large copper smelter in Australia commenced in 1848 at Bremer, near Callington some 60 km east of Adelaide. With larger discoveries on Yorke Peninsula, the Wallaroo copper smelter at Wallaroo Bay on the west coast of the peninsula commenced operations in 1861 (Bell & McCarthy, 2008). Thus began one of the most successful, and in its day, one of the most advanced and innovative plants in Australia if not the world. In the late 1860s, it was considered one of the largest copper smelters in the world (Bell & McCarthy, 2008)

Jan 1, 2019

By MAX VOS

Lithium is the lightest and electrochemically most reactive of all metals. Renewed interest in lithium coincides with research in lithium batteries and power generation by atomic fusion. Ontario lithium resources are contained in spodumene pegmatites that can form where medium- to high-grade metamorphic volcanic-sedimentary formations are intruded by pegmatite and porphyritic granitic rocks. Spodumene pegmatites occur in at least twelve locales throughout northern Ontario, all of which are in the Superior Province of the Precambrian Shield. Tantalum, cesium, rubidium, beryllium, niobium and tin also were noted with lithium in spodumene pegmatites. Considerable potential remains for discovery of additional lithium and rare-element pegmatites in northern Ontario.

Jan 1, 1984

By J. E. Reeves, J H. Morgan

Certain non-metallic minerals are used widely as fillers in the manufacture of many Canadian products. The first part of this paper deals in a general way with deposits of such minerals and their mining, with the concentration and preparation of the minerals for market, with specifications of the consumers, and with methods of control of the products to meet the specifications. The second part of the paper de-scribes talc as a specific example of mineral filler. Its production and uses in Canada and the possibility of producing higher grades of talc are discussed. Some suggestions are made for meeting the needs for mineral fillers as Canada's industry expands. RELATIVELY few people are sufficiently aware of the vast and important role that is being played in our everyday lives by mineral fillers. Many kinds of paints, papers and plastics, to mention three major classes of industrial products, are literally loaded

Jan 1, 1961

By Luke Meers

Roadway development rates in Australian underground coal mines are failing to keep pace with modern longwall systems and are unlikely to sustain further improvements in longwall productivity into the future unless step change improvements to roadway development equipment and practices are made. Bottlenecks which limit and constrain improved production and impact the safety of operators have been identified through a series of industry surveys, with the manual installation of strata support materials, consumables delivery, coal haulage and monorail installation being highlighted as major areas to improve development performance. This paper looks at research being carried out at the University of Wollongong in designing an integrated system approach for the fully automated handling and installing of development consumables, and the systems required to support these activities. A series of hard automation manipulation devices have been demonstrated in surface trials and the results indicate that rapid roadway development can be achieved.

Aug 1, 2013

By A. M. Richmond

Introduction The apparent commonplace, and prosaic, nature of building-stones, lime, cement, gypsum, and clay products, and many other miscellaneous non-metallic minerals, such as abrasives, barite, diatomite, magnesite, mica, slate, salts, etc., and their everyday appearance and necessary in our lives, has removed much of the glamour, romance, and speculative attractiveness so frequently associated with our gold, silver, lead, zinc, and copper mining ventures. However, it will be readily appreciated, with but a brief study of the thirty-five or more non-metallic minerals and products which are mined, prepared, or are known to occur, in British Columbia, that the 'industrial minerals' industry in the Province has an abundance of interesting technical problems, is fraught with speculative possibilities, and, as such, fully deserves much more technical attention than it has hitherro received. The brief notes presented in this paper show, in summary form, the magnitude of the British Columbia industrial and non-metallic mineral industry; outline in synoptically form the principal deposits of non-metallic minerals presently known; and indicate in a general way a few of the possibilities which exist in the Province for the expansion of the industry. For convenience in presentation, the assembled material has been divided into four sections: 1.-Sraristical information 2.-Strucrural non-metallic minerals 3.-Miscellaneous non-metallic minerals 4.-Non-Metallic mineral possibilities in British Columbia 1. -Statistical Information The writer does not propose to dwell at length on the statistical comparisons and deductions which may be drawn from the four tables which have been compiled for this section of the paper, nor is it considered essential, as the figures present a most emphatic story in themselves.

Jan 1, 1935

By Bahaa Hussein

Considerable number of methods and procedures has been introduced for trending and progress reporting of engineering, procurement and construction projects. This paper introduces a novel method, designed to augment the set of indices for measuring schedule performance. The concept behind the developed method is to provide early warning by dynamically evaluating the schedule cumulative impact of construction projects. The proposed method is designed to highlight the gradual deterioration in schedule status resulting in a cumulative impact due to the aggregation of small delays encountered during the execution of non-critical activities, and can be used as an add-on utility to existing software systems that perform CPM scheduling. The proposed method is based on a developed formulation for quantification of the Schedule Compression Index, which takes into consideration the remaining project activities durations. The index is developed based on periodic comparisons of ?Current Schedules? and the project ?Baseline Schedule? using the summation of the remaining activities durations. A numerical example is presented to demonstrate the application and capabilities of the developed method. It is expected that the developed index together with other schedule performance indices would be of value to decision makers and members of project teams.

Aug 1, 2013

By Suman Giri

Non-Intrusive Load Monitoring (NILM) is a method of extracting appliance-level power consumption information from aggregate circuit-level data with the goal of giving users feedback regarding their energy consumption so they can take control of their consumption habits. In this paper, we present a novel algorithm for classification of on and off states of appliances. We compare the performance of our algorithm in on state detection with a pervious paper that evaluated the same dataset and show that it performs up to 13% better. We also present the results of a case study where we collected data for different modes of a cooktop, microwave and dishwasher and used our algorithms to perform power estimation. The error on ten different setups in the test bed ranges from 1% to 32%. We discuss our results and lay out ideas for future work.

Aug 1, 2013