Search Documents

By J. E. McMenamin, R. B. Hall

"With the emphasis in the past decade on larger and more efficient equipment for open-pit operations, the Normandie mine of the Asbestos Corporation has followed the trend, switching from the smaller type of percussion drills to down-the-hole rigs. One 5 Y2 -in. percussion drill is still in use, but is limited to a ""smooth blasting"" role or to the control of the slope on final benches.In keeping with the times, an attempt was made to eliminate, as much as possible, the use of high explosives and to maximize the percentage of ammonium nitrate -fuel oil mixture. As the concentration of ground water increased with increased mining depths, small pumps were initially employed for the dewatering of boreholes. This proved unsuccessful, and a hole-blowing rig was built and a conversion to plastic liners made. The acquisition of a bulk-mix AN-FO truck has permitted the changeover from an AN premix to an ammonium nitrate prill -fuel oil combination at the borehole."

Jan 1, 1966

By T. W. Wong, M. A. Whitney, A. Hadadzadeh

Uniaxial compression tests were performed on cylindrical specimens, 10mm in diameter and 15mm in height, machined from an extruded AZ31B magnesium billet. The tests were conducted under isothermal conditions to a true strain of 0.5. The study compares macroscopic flow anisotropy between the extruded (ED) and transverse (TD) directions in the temperature range of 300°C to 500°C, and strain rate range of 0.001s-1 to 1s-1. Compression of ED specimens at low strain rate (0.001s-1) exhibited axisymmetric flow, and no significant differences were observed between geometries of specimens deformed above 350°C under the same strain rate. Deformation of TD specimens at low temperature and/or low strain rate resulted in elliptical cross-sections, with the anisotropy of flow being less significant at higher temperatures. Other studies performed using rolled plates have proposed that pyramidal slip and cross-slip at higher temperature eliminate the effects of initial texture, while the dominance of prismatic slip at lower temperatures will result in anisotropic flow. It is believed that the initial fiber texture common among extruded HCP-structured materials plays a role in the anisotropic deformation behaviour observed in the extruded specimens

Jan 1, 2015

By J. R. Giegerich

"IntroductionMINING operators in common with other operators are confronted today with two serious problems, shortage of experienced workmen and rising costs. The following review of practices at the Sullivan mine of The Consolidated Mining and Smelting Company of Canada, Limited, outlines certain measures that have been responsible, during recent years, for minimizing the effect of these two problems. The paper is divided into three main sections:( 1) Training programmes and job studies( 2) Improved mechanization and equipment( 3) Large-scale methods of operationTraining Programmes and Job StudiesJob TrainingJob training courses were introduced at Cominco immediately after the last war and proved to be a great benefit to the operations. There were three courses given, Job Instruction Training, Job Safety Training, and .Job Relations Training. These were spread over a period of two years and were taken by all operating supervisors and some key operators.The courses were introduced by a trained instructor from the British Columbia Department of Labour. This man trained twelve of our employees as instructors by giving them an intensive one-week course. Similarity between the three courses was such that the instructors trained in the first one were very readily trained for instruction in the two succeeding courses."

Jan 1, 1952

By Howard W. Tipper, Richard B. Campbell

"The Quesnel Trough is underlain by a thick sequence of mainly Upper Triassic and Lower Jurassic volcanic-clastic and sedimentary rocks that lie between the highly deformed Proterozoic and Paleozoic rocks in the Omineca Geanticline to the east and the Upper Paleozoic Cache Creek Group in the Pinchi Geanticline to the west. Broad areas of the Trough between Kamloops and Williams Lake are covered by Eocene volcanics and sediments and by Miocene-Pliocene plateau lava. Granitic intrusions were apparently mainly confined to two major episodes; one about 200 m.y. ago (coeval with the Guichon batholith) and one about 100 m.y. ago. In addition, the region includes small granitic and syenitic intrusions, some porphyritic, that may be all or partly still younger. Exposures in the region are generally small and scattered, obscured by widespread, not necessarily thick glacial deposits. This, together with the extensive Tertiary cover, makes prospecting difficult. The part of the Quesnel Trough discussed here is the direct northwest-ward extension of the copper-rich Kamloops-Merritt-Princeton region. It contains the Boss Mountain molybdenum mine, related to a breccia zone induced in a batholith of the oldest group by a younger intrusion, and the Cariboo Bell copper deposit in Lower Jurassic volcanic-elastic rocks and syenitic intrusions. The Gibraltar deposit, in a 200-m.y. intrusion, is within the Pinchi Geanticline close to the margin of the Trough. Molybdenum prospects are mainly restricted within or near the 100-m.y. granitic rocks. Copper prospects, on the other hand, are most prominent in the volcanic-elastic rocks and in the 200-m.y.-old granitic rocks, although they can also be spatially related to younger intrusions. Copper thus has a wide potential distribution.The writers believe that the region is deserving of careful and comprehensive exploration by directly applying the knowledge and techniques developed in the important producing areas to the south. All of the major pre-Tertiary geological elements seem to have potential for mineral deposits; none should be ignored. A thorough knowledge of the thickness and distribution of the Tertiary rocks and the development of geophysical methods to ""see through"" them is of particular importance."

Jan 1, 1970

By Zhiwei Wang, Chunsheng Qiao

"Aiming at the problems of the existing calculation methods for the support pressures of shallow tunnels in layered jointed rock strata, by using OAT (orthogonal array testing strategy) and DEM (distinct element method), 12 influencing factors including the thickness of the weathered overburden, and the states of the rock joints were considered. Then, the classification of the loosening zone was analysized. On this basis, by using the DEA (data envelopment analysis) theory, quantitative analysis on the influencing factors was conducted. By analyzing the influence of the key factors, a prediction formula of the boundary of the ringent trumpet-shaped loosening zone was established. According to principles of stress transformation, the formula of support pressures of the loosening zone which could considering the key factors were deduced. Finally, a practical case was introduced and studied to verify the proposed method.INTRODUCTIONIn recent years, various urban subway tunnels are increasingly carried out through jointed rock strata in many cities. Rock masses are discontinuous mediums with fissures, fractures, joints, bedding planes, and faults. The frequency of joints, their orientation with respect to the engineering structures, and the roughness of the joint have a significant importance from the stability point of view. However, there is a lack of understanding about the influence of the joints on the stability of tunnels. Therefore, how to measure the degree of the joints’ influence is a problem that needs to be solved.For the calculation of the support pressures, until now, many research results were focused on soil ground (Bierbäumer 1913; Terzaghi, 1943; Peck, 1969; Sabatini et al., 1999). In terms of site tests and model indoor tests, by measuring strut loads and calculating earth pressure based on strut spacing, the results proposed by Peck (1969) and Tschebotarioff (1973) have been widely used in practice for designing excavation support systems under sand (drained) and clay (undrained) soil conditions. Note that, it is unclear whether these findings could be extended to rock strata. For numerical simulations, how to simulate the states of the rock joints is a key problem that needs to be solved."

Jan 1, 2015

By E. J. Burrough

MR. J. J. McIntyre (International Coal & Coke Company, Ltd., and McGi1livray Creek Coal & Coke Company, Ltd., Coleman, Alta): Mr. Burrough's excellent paper, Metallurgical Coals of the Crowsnest Area, seems especially timely now, when the need for developing iron industries in the west, as well as in the east, is receiving so much attention. His -thorough review of the 'coking' industry is an especially valuable contribution, along with which the following brief remarks on coking in the Crowsnest Pass area of British Columbia and Alberta may be in order. When the Crowsnest Pass line of the Canadian Pacific railway was built there were great expectations for the non-ferrous metal industry; quite a number of smelter's were al-ready in operation in British Columbia and the northwestern United States, and further expansion was confidently expected. The suitability of the medium-volatile coking coals of the Pass for making metallurgical coke had been recognized from the time the fields were first explored. By the time the mines were fairly well developed there was already a market to war-rant the building of coking plants, and a common belief that expansion of the market would require a large coking industry. The first coke production was from plants built by the Crowsnest Pass Coal Company, Ltd., at Fernie, B.C. in 1903, and the International Coal and Coke Company, Ltd., at Coleman, Alberta. These plants were followed by others built by the Crowsnest Pass Coal Company, at Michel, B.C., by West Canadian Collieries, Ltd., at Lille, Alberta, and by Leitch Collieries, Ltd., at Passburg Alberta, and by a plant at Hosmer, B.C.

Jan 1, 1951

By Rong. G., T. Q. Lin, W. Du

Based on analysis of the evolutionary history of the valley in Baihetan, the mechanism of asymmetrical evolution, gradual migration-incision evolved from left bank to the right, is revealed in Baihetan river valleys. The process of in-situ stress evolution is carried out by using the Universal Distinct Element Code (UDEC). Consequently, the numerical results which indicate the main regulations of that stress field are as follow: (1) The phenomenon termed "high in-situ stress fold" appears in the bottom of the valley. With the maximum principal stress being 28-34 MPa, the stress increases significantly at a vertical depth of approximately 130 m. (2) The in-situ stress presents zonal distribution along the bank slope. It is apparent that the in-situ stress field consists of stress relaxation zone (SRZ), stress concentration zone (SCZ) and original stress zone (OSZ). The horizontal depth of stress relaxation zone varies from the left bank (roughly 200 m) to the right (about 120 m). Furthermore, the stress evolution of the left bank slope is studied. As a result, it is found that asymmetrical erosion contributes to the difference of the in-situ stress distribution as a critical factor, between the left bank and the right. And for an asymmetrical valley, the evolutionary process of in-situ stress field is a circular procedure, which includes the incision of valley, the accumulation of landslides and the migration of valley.

Jan 1, 2015

By T. Patching

"THE FOLLOWING notes on coal mining in the Edmonton city area are based, in the main, on scattered reports and accounts as little coal mining has been done in this area for about 20 years and few people are left who were involved in what was at one time an important industry of northern Alberta. Although coal mining is not likely to be permitted in the city area itself in the future, a record of this work is warranted to indicate the ·conditions and problems that may be encountered if underground mining again is proposed in the district in the same geological formations and in similar strata. Coal mining in the Edmonton area developed with the influx of settlers in the latter part of the nineteenth century and the first part of the present century. Probably local coal was used by the Fort's blacksmith as early as 1841, and the early settlers probably were 'gopherholing' into the outcrops along the river banks by the 1870s. The first report of commercial coal mining was in 1880 when a contract was let by the Hudson's Bay Company for the provision of 300 tons. As the population in the city and northern parts of the province grew, many new mines were opened along the river and in the district, and coal was even shipped by barge to points in Saskatchewan(1 ,2) By 1909 the Department of Public Works reported that 'Edmonton stands as the second largest domestic coal producing centre in the province'. It continued to hold this position until 1942. From about 1912 to 1951 annual production from mines in the city and surrounding district ranged between 0.38 and 0.65 million tons, depending on weather, wars and strikes. Production began to decline in 1951 because of the increasing availability and consumption of natural gas which was piped into the city and then provided to other towns and rural areas in the northern part of the province. Taylor noted that between 1880 and March 1970, when the last mine within the city area closed, the total of mines and prospects within the Edmonton city area rose to 153. Most of them were small; not more than 20 produced more than a quarter of a million tonnes during their entire life, and only three produced a million tonnes or more. As described by Taylor ""within the city district workings extend discontinuously from the apex of a narrow triangle near Groat Bridge to the base of the triangle in the Clover Bar area"". The larger mines were in this latter area. Approximate locations of the old mine workings in the city are shown in Taylor's atlas. A number of other coal mines were worked in the Rabbit Hill, Big Island, St. Albert, Namao, Cardiff and Morinville districts around the city."

Jan 1, 1985

By J-F. Béland, N. Parson

Aluminum extrusions are widely used for automotive crash management systems due to their superior specific energy absorption capabilities, as compared to steel. The Al-Mg-Si alloy series can be readily extruded into complex multi-hollow profiles, as required in crash systems, and can be used to target a range of desired strength levels. This paper focuses on the development of an axial crush test protocol and evaluation of the crush performance of common 6XXX series alloys for a variety of tempers. The observed crush behaviour is then compared to tensile test results.

Jan 1, 2015

By N. Dobrin, R. Sheinman, Y. V. Kokotov, L. N. Braginsky

Increasing the production of a Mixer-Settler unit requires either increasing flow rates or increasing extractant concentration. The mixers still have to ensure complete emulsification and to maintain high values of specific interface surface area in order to provide a high rate of mass transfer. Theoretically, an increase in mixing intensity can support increased flow rates without reducing extraction efficiency. Unfortunately, conventional pump mixers and mixing systems create small droplets that do not separate easily. As pumping action and mixing intensities are increased, the quantity of small droplets increases. We describe the development and industrial application of a novel mixing system for efficient mass transfer without forming significant quantities of small droplets, targeting both high mass transfer rate and low entrainment values.

Jan 1, 2014

A mini- or micro-machine is a small electro- mechanical device. There are several existing applications of micro-sensors such as the accelerometers used in automobile airbags or the force sensors and grippers used at the ends of micro-surgery tools. Potential applications of existing mini- and micro-technologies are possible and could be used to improve the control and efficiency of fragmentation, heap leaching and other mining and mineral processing operations. A more radical proposition is to devise mass-produced, possibly disposable, minimachines that would operate in large groups. These would be the basis of highly selective, efficient, flexible, and clean mining and mineral processing methods. The paper is intended to promote discussion of how innovative applications of mini-technologies can be used to improve and radically change current mining and mineral processing methods.

Jan 1, 2002

By L. Bos

The availability and reliability of large grinding mills and their Gearless Mill Drives (GMDs) are of paramount importance for the grinding process. Although GMDs have been in service for decades, and are known for their operational efficiency (reliability and robustness with reduced operating cost per ton), compared to conventional drives, in the last decade due to certain reasons some failures led to serious unscheduled shutdowns and significant insurance events. The majority of these notable "insured" failures have happened on GMDs installed on relatively large mills, as the financial impact of a failure is proportional to the through-put of the mill. Despite the occurrences of these events, as mining operations are driven by lower ore grades and the ability to continue reducing operating costs per ton, the trend for having larger mills is still very present and there is no reason why this trend should not continue. It is obvious that if not handled correctly, the possibility of large value GMD loss events, coupled with the continuing increase in mill size or required availability and reliability targets, could potentially lead to major conflicts as it becomes difficult for the insurance companies to judge the risk and hence may result in hesitation to insure these grinding circuits. This paper will not only describe the conflicting situation from both an insurer's perspective and from an equipment supplier's perspective, but also how these conflicting challenges can be successfully mastered. It has to be noted that not only the mining companies themselves, but also their insurance companies and the involved equipment suppliers have a common interest: to reach the highest availability and reliability in order to avoid or at least minimize unscheduled shut down times, and most importantly prevent unplanned events that result in extended production stoppages or reductions in through-put of GMD driven mills. From the very beginning onwards, the complete service concept together with emergency plans must be integrated on every level in the design of the grinding circuit. This approach must be implemented continuously and without compromises by all involved parties during all following stages, such as basic design, detail design, manufacturing, quality inspection and testing, packing, transportation, storage, installation, commissioning, operation and maintenance. The concept of formal risk analysis related to mill operations, maintenance and spare parts strategies must be an integral part of mining companies? decisions related to the selection for installation and continued use of large mills powered by GMDs. The service concept in place for operating mills shall also have a clear focus on very early detection of any abnormalities, so that the risk can be mitigated and unscheduled shutdown times avoided. However, if a major failure occurs, then procedures and tools shall already be available in order to ensure that production impact is minimized.

Jan 1, 2012

By G. Eaton

Safety management is an important mortal and business function in construction. Contractors have traditionally tracked and reported lagging indicators, e.g. fatalities and lost-time accident rates, to measure their safety performance and stay in compliance with relevant regulations. Over the last several decades, contractors became more proactive in their approach to safety and developed programs that track leading indicators, e.g. safety audits and safety climate. In particular, safety climate measures workers? perception of safety management and its effectiveness in the workplace. Past literatures indicated that, while some industrial construction contractors ignore safety climate measures, others are limited by a lack of a formal means to measure safety climate. In this study, a survey approach is used to measure an industrial construction contractor?s safety climate through three key areas: management commitment, job control, and general safety climate. As a pilot study, a total of 214 individuals at a fabrication facility participated in the survey to verify the validity and effectiveness of the proposed survey approach. This survey study also confirms that job control and management commitment have a positive correlation and that worker demographics have an effect on respondents? perceptions of management commitment.

Aug 1, 2013

By Fatemeh Pourakbari, Mohammad Reza Yarahmadi, Abbas Sam

Pyrite is the most abundant sulfide gangue mineral in copper porphyry ores. In spite of addition of lime in large quantities to depress pyrite in flotation, considerable amount of this mineral is reported to concentrate, particularly in rougher and scavenger stages. With the Sarcheshmeh pit advancing to a greater depth and reaching to the hypogene zone, the amounts of pyrite and chalcopyrite in the feed are increased. Hence, a reduction in the copper grade and increase in the sulfur content of the concentrate are observed. In this study the effective factors on the pyrite floatability at the circuit flotation was considered at Sarcheshmeh Mine. Mineralization zones in the pit were firstly identified. Then, sampling points were located using GPS system. On the basis of mineralogical composition and morphology, the ore was categorized into five main classes. In this classification the amount of lead and zinc and also pyrite locking with other minerals were analyzed. The study of polished section indicated that inclusion in pyrite was very frequent in all classes, mostly composed of the floatability of pyrite. Flotation tests were performed on the samples of different classes at pH of 11.8 after conditioning time. It was shown that, pyrite floatability was decreased with a decrease in the lead content of the feed samples except for the second class, while for all classes an increase in zinc content contributed to a decrease in pyrite floatability and recovery. It was found that, the lowest pyrite recovery (1.89%) was corresponding to pyrite–molybdenite dominant mineralization with Zn of 0.33% and the highest recovery (86.89%) corresponding to pyrite vein dominant mineralization with Zn equals to 0.9%.

Jan 1, 2016

By A. M. King, J. M. Neilsen

"Roughness at varying scales is an important component of the shear strength of discontinuities. Small scale roughness can be assessed in drillcore and through laboratory testing of drillcore derived samples. Large scale roughness, or waviness, also plays an important part in peak shear strength and a number of methods for its incorporation into defect plane strength models are presented.A number of methods for capturing waviness data from exposed faces are reviewed. A method is presented for deriving waviness from downhole televiewer data, which is shown to be significantly more accurate than structural data derived from core logging. The method is based on work undertaken in the highly anisotropic bedded units of the Hamersley Province, Western Australia where televiewer surveys are routinely undertaken. Values of waviness are derived through a review of variation in dip resolved in the direction of the slope face. This method allows design engineers to incorporate large scale roughness in defect plane shear strengths at the design stage.INTRODUCTIONThere are a number of constitutive models currently being applied by rock mechanics practitioners in calculating defect plane shear strength parameters, such as Patton, Barton – Bandis and Hencher [1, 2, 3]. Most of these shear strength determinations are typically undertaken by determining the base or residual friction angle, and applying corrections for small and large scale surface roughness."

Jan 1, 2015

By Takashi Nakamura, Atsushi Iizuka, Yong Fan, Etsuro Shibata

The level of iron in typical copper slag reaches nearly 40% by mass, in the form of iron silicate. We designed a method to oxidize the nonmagnetic iron silicate to magnetite, permitting the selective recovery of the slag’s iron content by magnetic separation. This would effectively decrease the volume of dumped slag; the reclaimed iron could be used for iron and steel making. The crystallization behaviors of magnetite and hematite were studied as reaction products of the molten oxidation of copper slag. A gas atmosphere of 1% by volume of oxygen was found to effectively precipitate the slag’s iron content as magnetite.

Jan 1, 2015

By L. K. Sinclair

In situ leaching of copper has the potential to deliver low-cost recovery for soluble copper deposits of sufficient permeability. In order to provide key inputs for modeling of the in situ leaching process, bench scale test work can be used in conjunction with geochemical software to identify key leaching and precipitation reactions. A case study is presented in which a series of flow-through acid leaching tests were conducted on drill core sections from a porphyry copper deposit without crushing or grinding. Concentrations of copper and other key elements were monitored in the recirculating leach solution over several months. A geochemical model of each leaching test was prepared using Geochemist's Workbench using a combination of diffusion-controlled and reaction-controlled rate mechanisms. Key reactions included leaching of chrysocolla, iron oxides, and plagioclase. The model was able to simultaneously satisfy the evolving chemistry of the recirculating leach solution, mineralogy of the head and leach residue, measured acid consumption, and leaching rates for key minerals reported from previous laboratory studies. Opportunities and limitations for scaling up the model to simulate the commercial wellfield are discussed.

Jan 1, 2015

By D. D. Downing

This paper is a review of material selection considerations concerning protective coatings in the mining industry. The discussion will cover both capital-dollar projects and maintenance requirements. Emphasis will be on industrial finishes for structural steel and process equipment subjected to aggressive atmospheres. The presentation will cover the total needs of a job, emphasizing not only the owner's requirement for a cost-effective system during plant operations, but also taking into consideration the short-term requirements of general contractors, steel fabricators, erection firms and paint contractors.

Jan 1, 1979

By J. Gao, H. O. Gekonde, S. V. Subramanian

"The functional role of inclusions at low cutting speeds is to promote ductile fracture in chip formation process, whereas the role of inclusions at high cutting speeds is to prevent tool crater wear by suppressing the tribological phenomenon of seizure at the tool-chip interface. Glassy oxide inclusions are engineered into the workpiece to form a viscous layer in-situ at the tool-chip interface at high cutting speeds. The viscous layer lubricates the tool-chip interface to prevent the seizure. In comparison with the large volume fraction of inclusions needed for promoting ductile fracture at low cutting speeds, the amount of inclusions required for lubricating the toolchip interface at high cutting speeds is very small and is in the range that is typical of clean steels. The chip fracture process at high cutting speeds is aided by strain rate hardening of the matrix, which facilitates chip disposal of relatively clean steel.Inclusion engineering for high speed machining involves the control of the rheology and composition of inclusions to meet target viscosity at the tool-chip interface. The application of thermodynamic models in controlled production of inclusions in steels designed for high speed machining is discussed."

Jan 1, 1998

By S. Hopkins, J. Nolan, S. Gillis

"Cast in place concrete shaft linings have been used in many salt and potash shafts sunk in North America over the last 100 years. A large number of these shafts have exceeded their initial design lives and as producers look to extend the life of their operational assets, maintenance costs and shaft downtime will, in many cases, continue to rise unless repair work is undertaken. Successfully implementing concrete liner repair schemes in operating salt and potash shafts is complicated due to their age, environment and time constraints during inspection, detailed design and construction. This paper outlines a general approach to the repair of concrete-lined portions of these shafts, based on lessons learned from the authors’ involvement in a recent repair project. INTRODUCTION Prior to the recent boom in potash mine construction many of North America’s potash mine shafts were entering their sixth continuous decade of production (Table 1). Of North America’s salt mines, one has been in continuous production, for nearly nine decades.As would be expected, considering the environment in which these liners operate and the age of the material, the concrete-lined sections of the shafts outlined in Table 1 have been noted by the authors to have lost both cross-sectional thickness and strength over time. Since construction, three principal factors have contributed to this loss in section/strength; (1) physical degradation (impact, freeze/thaw or rebar expansion), (2) chemical degradation from brine/water inflows (Neville 1969; Bothwell, 1972) and (3) overstressing of the liner. These factors may act in combination, in which case they can produce more significant distress than individually. Physical degradation There are three main causes of physical degradation of concrete shaft liners. The first is impact from falling debris/tools or equipment (whether large or small), which may damage specific sections of concrete lining as they fall through the shaft. Impacts tend to damage infrastructure fixed to the shaft liner more than the liner itself, so damage from this mode of failure is usually localised, for example, where bolts fixing a shaft services bracket to the wall have been pulled away, pulling out the concrete around the bolts with them."

Jan 1, 2019