Search Documents

By J. C. O'Rourke

"Gibraltar Mines Ltd. has been operating its open pit copper mine for fifteen years. In that time over 140 million tons of waste and low grade material has been placed on the mine waste dumps. Laboratory and in-situ testing indicated that enough leachable copper was recoverable from the dumps to justify a leaching operation which would include the construction of a solvent extraction-electrowinning plant. The plant, which was commissioned in October, 1984 was designed to process 3,000 usgpm of dilute copper solution to produce 5,000 tons per year of high quality cathode copper.This paper deals with the start up and initial year of operation of Gibraltar's SX-EW plant. The three areas: leaching solvent extraction and electrowinning are presented with emphasis on the innovations which were made to help overcome the problems unique to die Gibraltar operation.THE LEACHING CIRCUITThe mines waste dumps are leached to produce a pregnant copper solution as feed to the SX-EW plant. To achieve this the dumps are sprinkled with a mildly acidic solution which percolates through the dump. In travelling through the dumps the solution contacts the surfaces of the liberated copper minerals and disolves the soluble copper into the form of copper sulphate. The leaching reaction is achieved by a combination of bacterial action to oxidize the suphides and solublization of the copper into the acid solution.For the bacterial action to occur the dumps must be at or near the ideal pH of 1.9 - 2.1 and the necessary elements of the reaction must be present. Because a bacterial reaction is involved there is a lag time between the time when the conditions for bacterial growth are achieved and when the bacteria are in their active growth phase. Laboratory tests with Gibraltar ore indicated that bacterial action takes two to three months to reach its maximum rate. See figure 1.The expected lag time for the planned rate of bacterial leaching prompted Gibraltar to start irrigating the dumps in late June 1986 for a plant start up in early fall. The lag time proved to be longer than expected and the dumps took until November to start producing copper at the expected rate. See figure 2."

Jan 1, 1988

By T. Krumins, F. C. Ruff, M. Eichhorn, L. Zunti

Hatch Ltd. has recently completed a project to increase refractory gold ore processing capacity at Newmont Mining Corporation’s Twin Creeks facility. The objective of the project was to increase throughput by approximately 10% by adding a third autoclave feed pump to each of the two autoclave circuits. To minimize project capital cost, autoclave feed pumps from Newmont’s decommissioned Lone Tree facility were evaluated and found to be suitable for this new service. The existing pressure oxidation circuit was reviewed in a debottlenecking study to determine other upgrades required to facilitate the increased throughput. Interruption to operations was minimized with a detailed construction plan, supplemented with detailed 3D layout model sequencing studies. The focus of this paper is project development, multi-discipline design considerations, and implementation results.

Jan 1, 2014

By W. R. Tyson

IT HAS BEEN KNOWN for many years that alloy steels can become brittle when tempered in the range of 350-600°C, or cooled slowly after heating to higher temperatures. The metallurgical literature reveals that blacksmiths were aware as early as 1883 that water quenching was necessary after heat treatment above 600°C to avoid brittleness. It has also been known for years that the problem is associated with trace impurities; a paper in the Journal of the Iron and Steel Institute of 1894 refers to the brittle, faceted fractures that occur in steels containing arsenic, phosphorus or sulphur. However, definitive investigation of the mechanism of embrittlement has been possible only within the last decade with the introduction of new experimental techniques to investigate surfaces, especially Auger electron spectroscopy. It is now possible to study in detail the chemistry of surfaces with a resolution of an atomic layer or two, and enormous progress has been made recently in studying the segregation of impurities to grain boundaries by exposing the boundaries by fracture inside the microscope. A clear picture of the processes occurring and their interpretation is now emerging, as was particularly clear at the recent 1977 ASM Materials Science Seminar on Interfacial Segregation held in Chicago in October. Recent research in this area has pointed the way for commercial exploitation of this new knowledge and experimental technology. It is the purpose of this article to trace progress in understanding temper embrittlement and to indicate other areas where control of interfacial segregation and its effects can be important in metallurgical applications.

Jan 1, 1978

By S. P. Cashin, D. Kashuba, W. Esplin

Barrick has had 6 autoclaves in operation at the Goldstrike Mine, North of Carlin Nevada, since 1993. The 6 autoclaves operate in parallel, processing slurry of gold ore. The gold in the ore is predominantly associated with, and encapsulated by, sulphide minerals. It is necessary to oxidize at least 90% of the sulphide mineral before the gold can be concentrated using a cyanide/carbon-in-leach (CIL) circuit. Sulphide oxidation chemical reactions occurring in the autoclaves are exothermic; however, the sulphide content in the ore is not high enough to operate the autoclaves in an auto-thermal mode. Heat from steam is added to the first 2 of 5 autoclave compartments to initiate the sulphide oxidation reactions. The steam used to heat the autoclaves is supplied by three boilers, which are fuelled with propane gas. The completion of a few operations and maintenance projects in the last 2 years has resulted in a 50% reduction in propane energy requirements. The autoclave operating temperatures were minimized. Excess oxygen addition was held as low as possible. The material of construction for the compartment walls inside the autoclaves was changed from brick to Titanium metal. And, the speed of the autoclave slurry agitators was increased. All of these activities had an impact on the propane energy requirements of the autoclaves. Presented below is a description of the autoclave systems, and a discussion of how the energy needs were reduced, resulting in significant operating cost savings.

Jan 1, 2004

By K. J. G Hedges

"Once a health based guidance limits for exposure to diesel exhaust have been established, and as part of a multi-disciplinary team, the program for exposure reduction should incorporate the plan-do-check-adjust cycle. Setting a suitably protective (health based) occupational exposure limit (OEL) for diesel particulate matter (DPM) and nitrogen dioxide is a key driver to reduce exposure. It is important to go beyond regulations and reduce exposure to diesel exhaust, DPM, as low as reasonably achievable (ALARA) such as that prescribed under the Australia, Queensland Mining and Quarrying Safety and Health Regulation 2017 where under section 135 Limiting workers exposure, the workers exposure must not exceed the exposure limit applying to the worker for the hazard; and is ALARA. It appears that previously acceptable OELs are no longer safe. Therefore it is important that the internal responsibility system be implemented and the precautionary principle approach be followed, especially as it may be some time before a suitably protective OEL specifically for DPM is in place. One leading multi-national mining company BHP Billiton has acknowledged a significant lag that exists between regulatory action and the level of science that informs health risk. This company is managing exposure to diesel exhaust to as low as technically feasible. This same company that has set an interim target for managing diesel exhaust to 0.03 mg/m3 is achieving these levels which paves the way for other mining companies and general industry including construction. The Occupational Cancer Research Centre 2017 recommends reducing personal exposure to within 0.02 mg/m3 (EC) for underground mining and 0.005 mg/m3 for other workplaces. Controlling DPM is important to prevent cancer however it is also important that that nitrogen dioxide (NO2) be reduced (ALARA) and that careful selection of control technology be considered such as the proper selection of a diesel oxidation catalyst so that the level of NO2 does not in fact increase. The example from BHP Billiton provides a leading practice including using a multi-disciplinary approach and the importance of controlling emission at source and having an auditable diesel emissions based monitoring program in place."

Jan 1, 2019

By A. Warczok

Chalcocite concentrate obtained by magnetic separation and flotation of Bessemer matte is processed in the Inca top blowing bottom stirring MK reactor into semi-blister copper. The semi-blister is then converted into blister copper in the multi-purpose vessels (MPV) by oxidation of iron, nickel and sulphur. High melting point NiO and Fe30 4 are formed inside the MPV s, which together with Cu20 and smaller amount of fayalite are the major constituents of the solid mush. The accumulation of solid mush and buildup requires periodic MPV cleaning by adding reductant and copper-nickel matte, a unique process called "washout". Various reductants and their combinations, such as pig-iron, 15%Si Ferro-silicon and 50%Si Ferro-silicon, have been used for the reduction of solid mush and buildup. The possibilities of using calcium carbide as a reductant and slagging flux were examined experimentally at the crucible scale. The rate of reduction of MPV buildup was determined by continuous measurement of CO and C02 contents in the offgas and the flowrate of argon carrier gas. The rate of the buildup reduction with calcium carbide was approximately five times faster than the rate of reduction with coke. Additionally, the formation of CaO results in the melting of reduced buildup and formation of a slag at 1300°C and higher temperatures. It was found that simultaneous silica addition enhanced the melting and slag formation. The results showed the strong dependence of the reduction rate on temperature. Activation energy is approximately 225 kJ/mol. Expected benefits of using calcium carbide are related to cost saving on reductant, significant acceleration of solid mush reduction, and reduced amount iron input from reductant.

Jan 1, 2007

By M. Meratian

The in-situ methods have been developed in production of aluminum matrix composites. A commonly adopted in-situ method involves reaction between a metal oxide and aluminum to produce alumina particles or whisker reinforcements. Aluminum-alumina particle composite was fabricated by in-situ method where alumina particles were produced from reduction of copper and silicon oxides by melting and casting aluminum. Aluminum matrix composites reinforced by Copper and Silicon alloying elements and alumina particles have been obtained. The size and shape of alumina particles were studied by scanning electron microscopy (SEM). The size of alumina obtained from mixture of SiO2 and CuO was bigger than the alumina particles obtained from CuO.

Jan 1, 2007

By A. E. Flynn

Introduction The purpose of this paper is to record the results of researches on anhydrite that have been undertaken at the Nova Scotia Technical College during the last two or three years. The work was carried out in the Mining Department of the College, and several investigators were engaged on the work from time to time. Messrs. R. E. Hanson and K. M. Ed devoted their mining theses to the investigation, and Messrs. J. C. Hall and G. W. Baker were engaged on the work during the summers of 1928 and 1929, respectively. The writer was responsible for the initiation and direction of these researches, which were made possible by the financial assistance of the Department of Mines of the Province of Nova Scotia. Nova Scotia is the leading Province in Canada for gypsum production, its output being about a million tons per year, or over 80 percent of the production for the whole of Canada. The commanding position of Nova Scotia in this regard is due to the abundant supply of gypsum and its proximity to areas of intense utilization in the eastern United States. The resources of gypsum are contained in a total area of 627 square miles of gypsiferous rocks, so that an enormous reserve of this mineral is available. Present operations are confined to the highest grade and most easily worked deposits close to water transportation.

Jan 1, 1930

By M. G. Goudge

IT IS ENOOURAGING indeed to note during the past year that, despite a slackening off in many markets and with numerous major difficulties and problems to solve, the mining industry of Nova Scotia was maintained at a very high level. The value of the Province's mineral production for 1957 amounted to approximately $65,000,000. This represents a drop of only 1.5 per cent from the figure of the previous year. Coal Atlantic Collieries, Ltd., opened a new coal mine during the year at Bras d'Or. This colliery is equipped with the most modern type of mechanical equipment available, with transport of the ?coal by a belt-conveyor system. Other mines in the Province continued to mechanize their operations by the addition of Diesel haulage locomotives and other mechanized mining equipment. New wash plants are in operation and .an additional one is planned.

Jan 1, 1958

By Abhiram Shankar

Construction projects are becoming more demanding both in terms of time and complexity. This necessitates intricate planning and sequencing of activities at the macro and micro level and continuous flow of resources across the project in order to achieve planned targets. Work and Resource planning need to be done in such a way that limited resources give optimal output. Currently dominant activity-based scheduling techniques like Critical Path Method (CPM) and Program Evaluation and Review Technique (PERT) do not model work-flow or resource-flow through a project life cycle. An extension to the conventional activity based planning is Location Based Management System (LBMS). LBMS has been explored and utilised in the case of repetitive and cyclic projects such as high rise buildings. This study focusses on the application of LBMS to repetitive and non-repetitive components of Power Transmission and Distribution (PT&D) projects involving construction of substation and cable laying. This paper presents the findings on comparing the current planning practice for cable laying with an LBMS based approach. A key finding of the study was that the conventional practice resulted in a schedule with several coordination issues that could not be identified in the planning reports. Using the LBMS based approach these issues could be identified and decisions required for resolving these could be made.

Aug 1, 2013

By Edward Thomas

Note. - Securing mine roof through consolidating thin or otherwise incompetent strata to increase overall thickness of the immediate roof beam is a new method of roof support and control which has aroused great interest amongst mining engineers and which is now being experimented with and thoroughly investigated by the United States Bureau of Mines. A paper on Roof Bolting, illustrated by photographs and motion-picture films, will be presented by Edward Thomas, of the U. S. Bureau of Mines, at the forthcoming Annual Meeting of the Mining Society of Nova Scotia. In the following pages, Mr. Thomas describes the methods used in roof bolting as illustrated by the photographs that accompanied his paper. The photographs are supplied through the courtesy of the United States Bureau of Mines, whose willing cooperation with miners and mining engineers in Canada is very well known and even more greatly appreciated. This method of publishing Mr. Thomas's paper is adopted because few, if any, Canadian mining engineers have actually seen installations of roof bolts and it is felt that the best possible presentation of such an interesting subject through the medium of the Bulletin will be attained by publication of the photograps over explanatory captions. - Ed.

Jan 1, 1950

By Zihe Ren, Edouard Asselin, Marcus Tomlinson, Tianbi Zhang, Jing Liu

"Raman spectroscopy is used to quantify the extent of disorder in the carbonaceous matter associated with preg-robbing ores. Previous studies of Goldstrike ores showed that the height and width of the peaks for the “D” (disordered) and “G” (graphite) bands, the so-called “Raman ratio” had a strong correlation to the preg-robbing value (PRV) measured for various ore samples. A brief literature review on Raman spectroscopy as it applies to preg-robbing ores is presented. Further, recent studies, presented here, have shown no correlation between the Raman ratio and the PRV for a wide variety of ores. This suggests that the extent of organic carbon crystal disorder is not the main factor in determining preg-robbing characteristics.INTRODUCTION Preg-robbing may arise from natural carbonaceous materials in the ore. Several mechanisms have been proposed in the past decades including a physical sorption process by the carbonaceous matter, or via the reduction of aurocyanide at the mineral surface (Abotsi & Osseoasare, 1986; Afenya, Osseoasare, & Abotsi, 1983; Tan, Feng, Lukey, & Van Deventer, 2005). Nevertheless, the mechanisms of preg-robbing remain poorly understood. Understanding the nature of the preg-robber is of practical importance for the selection of a suitable treatment process. Fine carbon particles in the ore have been recognized as preg-robbers due to their similarity to the activated carbon used in the carbon in leach (CIL) or carbon in pulp (CIP) processes. Previous research has illustrated that the activated carbon (also referred to as amorphous carbon in some literature) has a much higher absorption ability than pure graphite with high crystallinity (Adams & Burger, 1998). Adams et al (Adams, Swaney, Friedl & Wagner 1996) concluded that carbonaceous matter is largely responsible for the overall preg-robbing capacity of a given ore. However, the mechanism of carbon preg-robbing was still not clear mostly due to the complexity of amorphous carbon and its behavior in different solution matrices, and at different pH and temperature (Adams, 1990, 1993)."

Jan 1, 2017

By V. Bondarenko

The importance and necessity of gas hydrates deposits development followed by natural gas extraction is considered in the present paper. Analysis is given to world sources focused on methane hydrates formation conditions. Information covering the most perspective gas hydrate deposit of the Black Sea is presented in the article. Two most common methods of gas hydrates development ? thermo stimulation and inhibitor injection are analyzed presenting their comparative characteristics. Basic scientific trends and developments of underground mining department in the field of gas methane extraction from gas hydrates are scrutinized. Schemes and methods of natural gas hydrates development are shown together with formulas, parameters and factors influencing the extraction process. Also the analysis is given to the possibility of gas hydrates formation from methane-air mixtures of degassing wells from coal mines of Ukraine. Improved experimental unit for gas hydrates formation under laboratorial conditions is presented with its basic characteristics. General conclusions and basic tasks requiring further research are given in the end.

Aug 1, 2013

By Victor F. Hollister, Robert W. Hodder

"The petrology and mineralogy of porphyry copper deposits are thoroughly described in recent literature and cited as the definitive characteristics for this type of deposit. The magmatic-hydrothermal aspect of genesis is also dealt with in detail. However, descriptions of their internal structure and regional setting are not as rigorous, and the genesis of this structure is simply stated as the release of high fluid pressures in a cooling magma emplaced along large fault zones. Genetic relationships between internal structure, regional setting and the tectonic evolution of continents has been alluded to infrequently in the past, but can now be considered together within the developing concept of orogeny at the margins of drifting crustal plates.Tensional structures, on both local and regional scale, and a Triassic to Tertiary age are described for porphyry copper deposits. We contend that such structure and age are distinct and unifying characteristics for this type of deposit and are genetically related to major crustal movements. British Columbia has porphyry copper deposits contemporaneous with plutons 180 to 200 million years old and 40 to 60 million years old. The former age group correlates with early stages of the continent's westward drift, and the latter group with a change in tectonic style during late development of the Canadian Cordillera. Hence, one can in British Columbia reflect on the genesis of a deposit's structure in the broader context of tectonic evolution. Such consideration should lead to more definitive criteria for area selection in exploration."

Jan 1, 1972

By Dong-min Lee

As the construction industry is becoming more large-scaled and complex, the BIM technology has been utilized throughout the industry. Since 2008, the construction industry in South Korea (Korea) has required carrying on BIM-based project continually. According to this trend, BIM S/W market, as well as BIM library market is also gradually activated. Many countries have already been establishing Web-based BIM library market, also Korea has been trying to establishing this Web-based BIM library market. In this study, through market research of Web-based BIM library market of advanced countries including the U.S.A. and U.K., establishment strategy of BIM library market to be derived by late starters that introduce BIM such as Korea, Japan and China was deduced based on current establishment status of BIM library market in Korea. In addition, deal with an issue that a clear revenue-sharing system between business principals of Web-based BIM library market is not available at the current stage was presented as a factor of inhibiting activation of BIM library market. So in order to offer a reasonable revenue-sharing strategy in BIM library market as conceptual level, a methodology and process of applying Game theory being used for deriving. It is expected that a reasonable revenue-sharing model between business principals would be presented as its standard of BIM library market to be more activated in the future.

Aug 1, 2013

Despite the claims of energy efficiency and the considerable development that has gone into dramatically extending rolls? life and facilitating rolls? change-out, in the six years since the last SAG conference, only a few HPGR operations have entered the realm of mineral processing. Risk barriers to the take-up of new equipment or processes are: a massive increase in materials handling issues as well as in the number of pieces of equipment required, low total circuit potential energy savings, and similar or higher capital costs. An alternative route is to make use of the complementary strengths of the HPGR and SAG in hybrid circuits. Minimising materials handling issues, providing an ideal balanced feed to the AG or SAG mill, and improving controllability through shifting grinding load as the RoM feed changes, are all potential major advantages to this approach. Conceptual circuit layouts, based on real measured ore and equipment data, are presented here to illustrate the potential production upside, the reduction in operating costs and the reduction in the physical and energy footprints.

Jan 1, 2012

By A. G. Mattes

This paper presents an overview of passive, engineered, biologically-based anaerobic bioreactor (ABR) treatment systems of the sort that can be used to remove dissolved copper from mine wastewaters. The paper begins with a brief history of the origins of this treatment technology and continues with a discussion of principles of engineered wetlands (EWs, advanced kinds of constructed wetlands, CWs) and the use of vertical sub-surface flow (VSSF) varieties that contain pulp & paper biosolids as the reactive medium for EW cells. A brief outline of a procedural methodology used in evaluating the potential for biological treatment on a site-specific basis is also included. An introduction to the microbiology of passive biologically-based treatment systems is followed by some recent research results in the general area of wetlands and ABR research. The paper concludes with a brief discussion of several sites known by the authors to have successfully (or not) demonstrated the potential of this treatment option.

Jan 1, 2007

By T. L. McCall

AUTHENTIC records show that coal mining in Cape Breton dates from the year 1720, when the French military authorities obtained coal from what is now known as the Blockhouse seam, in the Morien district, for use at Louisburg, where the fortress, now of such historic interest, was being built. Thereafter, coal was mined more or less continuously, and although, for many years, in a very haphazard way, there was, on the whole, a steady growth towards a better regulation of the industry, culminating in the year 1825 with the arrival of the General Mining Association in Nova Scotia. This Company, more generally known as the G.M.A., had acquired extensive tracts in Brazil and Colombia and had also purchased the mining rights for the whole of Nova Scotia-excepting such areas as had been previously leased-the attraction being the rich veins of copper currently reported as occurring in the Province. These fabulous copper veins, upon examination, failed to materialize, but the engineer sent out to report on them returned with such good accounts of the coalfields he had seen that steps were taken immediately to investigate them. From that rime onward, the history of coal mining in Nova Scotia is one of progress and achievement. One of the first acts of the G.M.A. was to acquire the areas already leased to other concerns and develop these in a masterly fashion, employing the best machinery and talent available at that time. Such dominant control over the minerals of the Province, although it led to orderly development in the several coalfields, also, later on, resulted in restricting operations in the various coal centres to such an extent that a determined effort was put forward by the people of Nova Scotia to end such a state of affairs. Consequently, in 1857, the original lease of the G.M.A. was abrogated, the Company, however, being allowed to retain certain areas in the districts it had already developed. This opened the way for the formation of other coal-mining companies, and numbers of these immediately sprang into existence in the various coal-mining centres. In 1893, the Dominion Coal Company, Limited, was formed by the amalgamation of seven companies operating in the neighbourhood of Glace Bay, in Cape Breton. Later, in 1910, the Dominion Iron & Steel Company, Limited, obtained control of the Cumberland Railway & Coal Company, which had been formed in 1884 to acquire the rights of the two companies working in the Cumberland County coalfield.

Jan 1, 1936

By P. R. La Pointe, J. Clark

"Studies have shown that the roof in coal mines is nearly twice as likely to fail at intersections as at entries due to enlarged roof spans, stress redistribution and other factors. However, the relative stability of intersections in a mine varies, and an improved understanding of what factors impact roof instability can lead to efficient, proactive mining practices that both enhance stability and mining efficiency.A study was undertaken at an underground longwall coal mine to develop a model to predict the stability at the intersections of entries and cross-cuts. The statistical analyses relied upon observational and measured data regarding the development of tension cracks, seepage, intersection geometry, mining practices, geological attributes and geomechanical factors at 783 intersections. Each intersection was given a NIOSH roof. Common data mining techniques, such as multivariate linear regression, multinomial logistic regression, decision trees and probabilistic neural nets, were considered and evaluated to establish correlations and associations between stability and the other variables. Two of the more successful techniques were Decision Trees and Multinomial Logistic Regression. The analyses showed that a number of factors impacted stability:• Overburden thickness (impact on stress concentration magnitudes)• Initial opening area (impact on stress concentration magnitudes)• Sulfur content (depositional environment & impact of mechanical properties, leaching effects)• Intersection type (impact on stress concentrations)• Gob distance (impact on stress concentrations)• Presence or proximity of a particular sandstone (impact on mechanical properties)• Roof bolt type and diameter (impact on reinforcement)Some factors showed no statistically significant relation to stability. These included:• Total area• Supported areaSeepage was a more problematic variable in assess. Seepage is associated with instability, but it is not clear whether seepage occurs as a consequence of instability, for example, through the creation of tension cracks, or whether the intersection has been excavated where water already exists and has degraded the rock prior to excavation, leading to greater instability.Seepage appears related to the geology of the roof rock mudstones, not the sandstones. Tension cracks in the intersections occur preferentially where the Sulfur content is below 0.9%. The Sulfur may relate to mechanical differences in the roof rock, and where the Sulfur is low, the roof is less stable, there are more tension cracks, and seepage is greater. This suggests that the weaker mudstones may be more prone the development of tension cracks, not because these rocks are more brittle, but possibly weaker.2-way and 3-way intersections appear to have less seepage than 4-way, although very few intersections overall have any seepage. This is similar to the roof stability, in which the 2-way and 3-way are more stable. 2-way and 3-way intersections have fewer-than-expected tension cracks, while 4-way have more than expected. These results suggest that four-way intersections are weaker and more prone to tension crack development, also suggesting that increased seepage results from weaker roof conditions, rather than the converse. Thus seepage appears to be mostly a consequence of instability rather than a cause and is higher where there are 4-way intersections, mudstone geology and external loading factors like depth of cover and proximity to gob that promotes crack development. The study also indicated that a better understanding of the mudrock facies could reduce uncertainty."

Jan 1, 2015

By W. Banda

"Trial application of air decks on a production shot improved fragmentation (32% reduction in x50). Empirical fragmentation models and digital image processing software were used to estimate fragment size distribution of the blasted muck pile. The x20, x50, and x80 passing fractions, and top size were 42, 265, 683, and 1,455 mm, respectively. Air-deck application reduced explosives load in blastholes, lowering total charging cost by US$20/hole (15% decrease) and the powder factor to an average of 0.86 kg/m3 (12% decrease). Blast results were 443,624 t of blasted material from the block (90% of total muck pile) was smaller than 900 mm.RÉSUMÉ L’application pilote de trous d’air dans le cadre du coup de mine effectué pour commencer la production a amélioré la fragmentation (une réduction de 32 % des x50). Des modèles empiriques de fragmentation et un logiciel de traitement numérique des images ont permis d’estimer la composition granulométrique des fragments du tas de déblais abattus. Les fractions de passé de crible de x20, x50, x80 et la dimension supérieure étaient représentées par des dimensions respectives de 42, 265, 683 et 1 455 mm. L’application de trous d’air a permis de diminuer la charge d’explosifs nécessaires dans les trous de mine, réduisant ainsi les coûts totaux de chargement de 20 $ US/trou (soit une réduction de 15 %) ainsi que le facteur de chargement (facteur poudre) à une moyenne de 0,86 kg/m3 (soit une réduction de 12 %). Les coups de mine ont résulté en 443 624 tonnes de matériaux abattus du bloc (soit 90 % du tas de remblais total) mesurant moins de 900 mm. INTRODUCTIONThe main objectives of production blasting are to achieve optimum rock fragmentation and to minimize overall production costs. Because blast fragmentation significantly affects the profitability of a mine, blasting is the first step of the size reduction in mining: An optimum size distribution is required to maximize the performance of mining and subsequent milling processes. If the fragmentation size distribution can be modelled and controlled, operations performance will improve. Blast fragmentation modelling is important in mineto- mill optimization: It allows the estimation of blast fragmentation distributions that can be modelled in downstream mining processes to determine the optimum blast design."

Jan 1, 2018