Search Documents

By G. W. McDonald

"The mineralogical studies done on Hope Brook ore samples indicated that a heap leach gold recovery process may be possible. In the metallurgicalprogram that followed, column tests confirmed this interpretation. A 9300 tonne demonstration heap leach test, in the late fall of 1985, reaffirmed laboratory results while identifying operating conditions that will have to be addressed in a production heap leach plan. Operating plans, gold recoveries and cost areas will be presented.Another important factor in a successful operation is the environment approach.LocationThe Hope Brook gold deposit is located 5 km inland from Cinq Cerf Bay on the south coast of Newfoundland. Port au x Basques is 80 km west and Burgeo 40 km to the east of Hope Brook. As there are no roads in the area, access to the site is by sea or air (Fig. I). The Hope Brook orebody is near the saddle of three watersheds flowing to Cinq Cerf Brook, Boat Hole Brook and Betty's Pond. Acceptable solutions to several environmental concerns can be obtained by using the relative sensitivities of these watersheds.The terrain at the site is generally rolling to hummocky with numerous small ponds separated with rock outcrops and patches of peat covering. Tree vegetation is sparse except in the sheltered areas around Couteau Bay and Cinq Cerf Brook. GeologyThe Chetwynd deposit is hosted by the Lower to Middle Ordovician Georges Brook Formation of the La Poile Group, a thick sequence of volcanic and sedimentary rocks.The Hope Brook Zone contains the largest concentration of gold found to date at Chetwynd. The zone occurs as an intensely silicified lens 100 m to 550 m long (average 400 m) by up to 60 m in width and forms the eastern portion of a more extensive, 4 km long , alteration zone trending at 053 degrees Az and dipping 70 degrees southeast.The Hope Brook Zone contains massive finely granular quartz, scattered blue quartz eyes, 3070 to 8% pyrite, minor calcopyrite and trace molybdenite. Barren silicification envelopes the gold mineralization. The zone is flanked to the southeast by a 200 metre thick aluminosilicate alteration zone and to the northwest by a 10 metre barren pyritic siliceous fragmental rock . The original lithology may be either a thick felsic pyroclastic sequence or a quartz porphyry sill that has been altered by hydrothermal processes. Silica flooding of the permeable host was accompanied by gold deposition."

Jan 1, 1989

By R. C. Reed, A. Akhtar

Oxidation of the third generation cast single crystal, nickel-base superalloy CMSX-10 is examined using isothermal tests at 900°C and 1000°C for times ranging from 20 hours to 100 hours. X-ray diffraction, scanning electron microscopy and energy dispersive secondary X-ray analysis were used to characterize the microstructure. It was found that the external scale formed at 1000°C is made up of (Ni,Co)O and the spinel NiCo2O4. The (? + ? ') microstructure of the superalloy transforms into the intermetallic (3 phase prior to the onset of internal oxidation. Internal oxidation results in the formation of (Ni,Co)Ta2O6 and (Ni,Co)WO4. No evidence was found for the formation of alumina (Al203), and the spinels NiCr2O4 and NiAl2O4 in this third generation superalloy. Results of the laboratory investigation are compared with those of an aero-engine turbine blade removed from service and examined earlier.

Jan 1, 2004

By Dougla McDonald, Richard Poulin

"Most mine managers in Canada today will agree that one of the keys to mining efficiency and productivity is their human resources. A5 a result, many mines develop some sort of incentive designed to tap their employees' capabilities to the fullest extent. Historically, the most common plans used have been ""piece-rate"" plans, where individual or small groups of miners are paid a financial bonus based on some measure of their productivity. Recently, however, incentive plans that take a more team-based approach have been developed in some Canadian mines. One such plan will be defined in this paper, and its popularity in the industry today discussed.Gainsharing PlansThere are two primary components to a gainsharing plan. The first is a cash incentive, which is paid to all employees and based on factors that are highly correlated with employee productivity, and key to the profitability of the mine. For example, the typical gainsharing cash incentive is based on the cost/unit of metal produced. Management (in consultation with employees in some cases) will establish the budgeted cost per tonne, and any savings in this amount is shared between the company and the employees. The second is a management philosophy and associated communication network, which is designed to foster an environment that encourages information exchanges, communication, participation, and trust between employees and management. The typical gainsharing communication network consists of two tiers of committees. The first, operational committees, include all employees working in the same department or departments which frequently interact. The employees meet monthly with management personnel to discuss problems encountered and brainstorm for solutions. In most cases, these committees will nominate a person in the group to structure the meeting to maximize its efficiency. The second, the screening committee, is a single group consisting of representatives from the various operational groups, whose primary job is to ensure that the plan is effective, and the objectives and results generated by the plan remain consistent with the mine objectives. In short, gainsharing plans tell employees that their bonus depends upon performance and then gives them the opportunity and incentive to affect that performance. The opportunity is provided by a communication network and positive management practices, and the incentive comes in the form of ""intrinsic"" rewards of participation and the ""extrinsic"" rewards of the bonus payments. Figure I will clarify the relationship between the intrinsic and extrinsic rewards."

Jan 1, 1995

By K. S. Coley, M. A. Rhamdhani, G. A. Brooks

Interfacial phenomena in high temperature reactions such as between iron alloy and slag is well documented but not fully understood. It is believed that a gradient of oxygen concentration plays an important role to the occurrence of such phenomena. This article describes the results from the continuation of the study of interfacial phenomena between Fe-Al alloy droplets and CaO-SiO2-Al2O3 slag. Materials characterization techniques involving microscopic observations, depth profiling, bulk, point analysis and were carried out. The roles of oxygen as well as other factors that contribute to the interfacial phenomena were evaluated. The results and their implications to steelmaking will be discussed.

Jan 1, 2004

By D. Ibarra, J. Jacob, A. G. Guezennec, P. d’Hugues, A. Archane

The lack of adequate gas mass transfer is a rate limiting step in many bacterial leaching processes. Oxygen often becomes a limiting factor because of its low solubility compared to the high demand induced by sulfide oxidation. One way of increasing the solubility of oxygen in water or in media solution is by increasing the driving force, i.e. raising the oxygen partial pressure in the gas stream supplied to the leach pulp. The use of oxygen is a well-known practice in high-temperature bioleaching reactors (above 70°C) whereas air is usually preferred in medium and low-temperature operations in order to avoid too high dissolved oxygen concentrations which could impact negatively the bacterial activity. The purpose of this study was to investigate the use of oxygen-enriched gas in bioleaching reactors at 40°C in order to improve the gas transfer in the system when operating at high solid load (20% and more). Bioleaching experiments were performed on a sulfide-rich tailing waste (pyrite 60%, copper 0.8%, cobalt 0.06 %, gold 1 g/t) using the “BRGM-KCC” bacterial consortia. The reactor used for the tests was designed on the basis of a new bioleaching reactor concept developed by Air Liquide, Milton Roy Mixing and the BRGM which uses floating agitators to inject gases and to mix and to suspend solids in the bioleaching solution. Two types of tests were carried out: with air injection and with oxygen enriched gas mix injection. The aim of this work was to confirm the capacity of bacteria to grow and to dissolve pyrite in this type of bioreactors in oxygenrich atmosphere, and to compare sulfides dissolution rates during both types of bioleaching tests. The results obtained show that the use of oxygen enriched gas mix does not decrease bioleaching performances compared to air injection. High metal extraction yields were achieved (above 80%). No deleterious effect due to oxygen use was observed on the bacteria despite the high level of dissolved oxygen reached in oxygen tests (up to 14 mg.L-1).

Jan 1, 2016

By A. Flemming

"As the next century draws near, new mine properties must be brought into production to replace existing operations that are approaching their economic life. This paper presents some of the critical technical issues being addressed by Manalta Coal Ltd. as they strive to bring the Telkwa Coal Project near Smithers, BC into production during the year 2000. The mine is planned to produce between 1.0 to 1.5 million tonnes per year of medium volatile coal for export to overseas thermal and PCI markets. IntroductionManalta Coal Ltd. (Manalta) is proposing the development and operation of a surface coal mine and associated infrastructure approximately six kilometres southwest of the village of Telkwa, British Columbia (Fig. 1). The infrastructure consists of a coal washing facility, tailings disposal area, clean coal haul road, access road and rail loadout facility. Over a 25-year period, the mine is expected to produce between 25 and 37 million clean tonnes of coal primarily for the export market.To achieve public and governmental approval for the development, the project will be reviewed under British Columbia’s Environmental Assessment Act. Manalta entered the formal Assessment process in February 1, 1997 with the submission of an Application for a Project Approval Certificate for the Telkwa Coal Project."

Jan 1, 1997

By W. L. Bancroft, Peter Price

"What is now known as the 'Waite section' of the property of Waite Amulet Mines, Limited, was originally the Waite-Ackerman-Montgomery mine. It includes a group of twenty-eight claims lying on either side of the Duprat-Dufresnoy township line, and about 8 miles north-northwest of Noranda, Quebec. ,The original discovery of ore on the property was made by Thomas Montgomery in Block Q, Duprat township, and was staked by him on behalf of himself, I. C. Waite, and C. H. Ackerman, in the summer of 1925. The property was optioned late in 1925 to N. A. Timmins who, after trenching and drilling the deposit, sold his 85 per cent interest to Noranda Mines, Limited. Early in 1927, a company known as Waite-Ackerman-Montgomery Mines, Limited, was formed and shaft sinking and development undertaken. Production commenced in August, 1928, ·and continued tJ May, 1930, when, owing to falling metal prices, shipment of direct smelting ore was stopped. Development of the mine by shaft sinking, drifting, and drilling continued until March, 1932, when owing to the prolonged low price of metals, the property was closed down. In September, 1933, an amalgamation with Amulet Mines, Limited, was effected, the new company being called Waite Amulet Mines, Limited. Early in 1937 operations were resumed, first by direct shipments to the smelter and later by aerial tramway to the Amulet mill. Operations have been continuous up to the present time, reaching an average of 720 tons a day milled for the year 1940. Production during the initial period (1928-1930) amounted to 75,811 tons, having an average grade of 7 .11 per cent copper, 4.47 per cent zinc, and 0.03 oz. gold and 0.65 oz. silver per ton. During the second period (1937 to end of 1946) , 1,060,524 tons, having an average grade of 4.53 per cent copper, 2.97 per cent zinc, and 0.03 oz. gold and 0.65 oz. silver per ton, were produced."

Jan 1, 1954

By Dennis Martin

What is Borehole Hoisting Borehole Hoisting is the use of a hoisting plant to hoist rock, workers and materials or both, vertically through a borehole, between a mine level and surface or between two levels of an underground mine. Screen and bolt ground support on walls of 5.5 m diameter borehole hoisting shaft

May 1, 2013

By A. Hosseini

Full-scale rupture tests were conducted on 508 mm (20 in) diameter API X-60 5.7 mm wall thickness pipes containing either axial semi-elliptical cracks or simulated corrosion defects with equivalent depths ranging from 20 to 60 percent thickness. In the case of the cracks, the failure pressures were predicted with reasonable accuracy when considering a level 3 failure assessment diagram (FAD) procedure based on API 579, as compared to level 2 FAD, since the mechanical properties were known. In both cases, the accuracy improved for shallower cracks. Considering simulated corrosion defects, the RSTRENG approach provided more reliable results on predicting the collapse pressure. For a similar depth and profile, the cracked pipes failed at a lower pressure than those containing simulated corrosion defects of equivalent depth.

Jan 1, 2010

By V. Evans

Mine lateral development advance rates currently average about 5 metres (16.5 ft.) per day. Granduc Tunnel hit 35.1 metres (115 ft.) on their best day, 12 km from the portal, single heading forty-three years ago. This Canadian mining record remains an excellent example of rapid drill and blast excavation with suggestions for improving current practice.

May 1, 2011

By Joanne G. Petrini

ISO 26000 Unique Process Unique Personality ?Almost 10 years in the making ?What type of standard is this? Different type of ISO Standard ISO 26000 Structure and Substance ?Principles ?Core Subjects ?Implementation Guidance ISO 26000 Impact ?Same old, same old? ?So Is there really anything NEW? ?Should I care??

May 1, 2011

By Kari Niiranen, Andreas Boehm

LKAB (Luossavaara-Kiirunavaara AB) is operating underground iron ore mine, with three beneficiation and pelletizing plants in Kiruna, Northern Sweden. The wet low intensity magnetic separation (WLIMS) is regarded as the crucial part of silicate mineral separation from the ore. The Kiirunavaara iron ore deposit shows a rather low content of silica (ca. 2.3 to 3.3 % SiO2) but the silica grade is expected to increase in the deeper parts of the deposit. This can be problematic in the case of DR pellet quality with an average silica grade under 0.75 % SiO2. A laboratory scale methodology was developed for the systematic characterization of the ore for mineral processing with the focus on silicates at the Institute of Mineral Processing, University of Leoben. This methodology is combining mineralogical, geochemical and process mineralogical characteristics. Automated mineralogy (QEMSCAN) was used to study the modal mineralogy, the distribution of silicate minerals in different particle size classes after comminution, the deportment of silicon (Si) between various silicates and degree of liberation and intergrowth of magnetite and silicates. Based on the mineralogical investigations, actinolite, phlogopite and even quartz and albite are the predominating SiO2 bearing minerals in the ore. The important result of the investigations was the discovery of two separate subtypes within the high silica ore type B2 based on their mineralogy and mineral processing characteristics. The crucial part of the investigations of intergrowths and liberation of magnetite results was the magnetic separation tests carried out with the Davis magnetic tube. The binary intergrowths of magnetite and the silicate minerals (mostly actinolite) are the most common type of mineral association discovered. The significant characteristics in the intergrowths of magnetite and actinolite are the fine-grained magnetite inclusions in actinolite which may end up increasing the SiO2 grade in the magnetite concentrate despite magnetic separation.

Jan 1, 2016

"Batch flotation testwork demonstrated that a low-grade chromite ore from Bird River, Manitoba, was best floated at pH 2 using Armac C (coco amine acetate) collector and sulphuric acid as pH modifier. A grind of 100% minus 150 um was necessary for liberation, and flotation selectivity was greatly enhanced by prior desliming. A concentrate analyzing 24.2% Cr203 with a recovery of 90.2% was obtained, after three cleaning stages, from ore grading 6.05% Cr203. Total rougher collector concentration was 500 g/t and cleaner collector concentration 380 g/t. Similar grade and recovery were obtained during the pitot-plant evalualion, when a concentrate analy zing 22.3% Cr203 with a recovery of 93% (based on deslimed feed) was obtained for a total collector addition of 630 g/t.Selective flotation in a region of positive surf ace charge implies anionic activation, and a possible flotation mechanism is suggested.IntroductionIn an earlier study(1) of the beneficiation of chromite ore from Bird River, Manitoba, several methods of beneficiation were explored. These included ore sorting, heavy-media separation, and gravity concentration with flotation using Armac C (coco amine acetate) collector at pH 2, and sulphuric acid as pH modifier. Because flotation was not fully evaluated, a laboratory study was undertaken to determine the optimum parameters of chromite flotation. Optimization of parameters was established first on a laboratory scale followed by confirmation a t the pilot -plant level. Flotation of chromite using Armac C and sulphuric acid as a pH modifier has been reported as being selective for low-grade chromite ores(2)."

Jan 1, 1990

By Roy T. Bowles

This paper focusses on technological developments which occurred in the village of Deloro, Ontario between 1868 and 1919. These developments illustrate the manner in which improved metallurgical processes linked Ontario mineral resources to industrial expansion. Overview of Deloro The village of Deloro is in Hastings county, about 5 miles from the village of Marmora, the site of the old Marmora iron works and the more recent Marmoraton iron mine. In this area, the Canadian Shield meets the Great Lakes lowlands. The first settlement in the vicinity occurred in the 1820s and was associated with the Marmora iron works. Settlement grew around agriculture. Gold was discovered in Hastings county in 1868. Deloro - the name derives from gold - developed as a concentrated settlement in proximity to several gold mines and the related processing activities. By 1901, substantial smelting works were successfully producing gold and arsenic from local ores. The village was developing as a company town within the framework of benevolent paternalism. For reasons associated with markets and with local ore supplies, the Deloro mills were idle for a period beginning in 1902. Developments in later periods connected Deloro to world events. In 1903, silver was discovered at Cobalt, Ontario. By 1907, M.J. O'Brien, who owned mines at Cobalt, had purchased the Deloro works and was using them to process Cobalt-area ores*.

Jan 1, 1999

By Michael S. Moats, Prashant Bagri

"In recent years with increasing concerns about energy consumption in hydrometallurgical processing, there is an ongoing attempt to use Catalytic Titanium Anodes (CTAs) for copper electrowinning. For this work, anodes with IrO2 - Ta2O5 coatings were prepared in the laboratory with the same total coating loading but varying the number of layers by changing the speed of withdrawal in dip coating. A second set of CTAs were fabricated on niobium, Ti Grade 1, Ti Grade 7 and Ti Grade 36 metal substrates. All the anodes prepared in the laboratory were characterized using standard electrochemical techniques and subjected to accelerated life testing. It was found that the coating would not adhere to the niobium substrate, the grade of titanium had a minimal to no effect on the life of the anode, and it is observed that as the coating speed slows, there is an increase in the electrochemically active surface area of the coating which seems to directly contribute to an increase in the Tafel slope of the anodes. There was inconclusive evidence on the effect of coating speed on anode lifetime.INTRODUCTIONLarge scale hydrometallurgical extraction of copper has become widely practiced over the last 40+ years. The hydrometallurgical route entails leaching, solvent extraction and electrowinning. With the increasing desire to process refractory sulphides like enargite and chalcopyrite through the hydrometallurgical route, use of hydro-processing of copper is expected to remain high.In conventional electrowinning, copper is deposited on the cathode and an inert anode is used for oxygen evolution. Presently, the most common anode material is rolled lead-calcium-tin and the cathode is 316L stainless steel (Robinson et al., 2013). This lead alloy is fairly inexpensive and is robust, providing lifetimes typically of 4+ years. The main drawbacks of lead alloys are their relatively high oxygen evolution overpotential, the need for cobalt in the electrolyte to reduce their corrosion, the contamination of cathode product by lead, and the generation of harzardous by-products (Hiskey, 1999)."

Jan 1, 2016

By Penny C. Stewart

Narrow vein underground stope design engineers in Australia have expressed significant interest in the requirements and methodology for developing site-specific stability charts. This is largely due to a concern that existing stope stability charts inadequately take into account factors influencing narrow vein stope stability, such as the effect of backfill abutments and the effect of in stope pillars. This paper presents conclusions from a comprehensive statistical examination of case history requirements for a site specific stability chart and critiques literature arguments for site-specific charts. A new statistical analysis technique and a large comprehensive stability database enabled the authors to quantify case history requirements and any site-specific effects the model exhibits. The analyses indicated that a reliable stable-failure boundary requires at least 150 case histories, of which a minimum of 10 percent should be unstable stope surfaces. Marginal site-specific effects were observed for the operating conditions captured within the database. The authors conclude that the apparent site-specific effects noted in previous literature are attributable to operating conditions inadequately represented in the database. Such operating conditions could induce erroneous stability predictions at any site, and are therefore not truly site-specific. Following from these conclusions, a strategy for taking into account operating conditions particularly relevant to narrow vein mining has been proposed. In particular, the development of a chart that accounts for the effect of backfill abutments on stope stability. Backfill abutment effects are particularly relevant to mechanised narrow vein mining methods such as modified Avoca. Collaboration from at least five sites is required to obtain access to relevant data and underground drives for geotechnical mapping. Preliminary estimations indicate that approximately three months fieldwork is required to meet case history requirements. CMS data in conjunction with 3-dimensional design software will be used to calculate equivalent linear overbreak/slough (ELOS). In contrast to stable, failure, major failure and caving categorical variables, ELOS is an objective and continuous stability variable and is therefore, more conducive to mathematical modelling.

Oct 1, 2001

By David R. Winfield

I would like to thank you for spending the time with me today to review the FLIR PathFindIR thermal imaging camera system: It is truly an innovative safety system that has the added benefit of offering increased efficiency Our company the Winsted Group, specializes in mobile video systems that are fully customizable to address standard and unique operational requirements in a variety of industries from heavy equipment cameras to police and military digital recording systems, high end video camera systems are a hallmark of Winsted?s product line. The use of thermal imaging camera systems to enhance mobile safety is a relatively new concept as it relates to their use in both transportation and heavy equipment operation. This technology, like so many before it, has been adopted for civilian use from its military roots. The identification of enemy combatants through their heat signature has given our troops a decisive edge in military operations in total darkness Likewise, the ability to discern people and objects that give off heat is a significant step forward in collision and accident avoidance. The PathFindIR camera system that I am demonstrating today is so advanced that it cannot be exported outside of continental North America without a US government approved export license I would like to commence my presentation with a short video clip that discusses the technology associated with the FLIR PathFindIR Thermal Imaging camera systems. The video demonstrates the operational effectiveness of thermal imaging camera systems installed on a vehicle operating on the roadway at night, of course there are definite parallels to use in a mining environment, primarily the fact that lighting is limited and the chance for vision limiting dust is ever present. We are, of course more concerned with personnel safety in our mines than encountering wildlife on the roadside. From the same perspective, the transport driver is just as concerned with encountering a stalled vehicle as our mine truck operators are with other mine traffic.

Feb 1, 2008

By M. Kim, M. Ha

"The effect of red mud on the melting behavior of ferronickel slag was investigated by a laboratory-scale horizontal tube furnace. Melting and softening of slag samples fluxed with different amount of red mud was examined by in-situ visualization technique at temperature range from 1400 to 1550°C. FactSageTM 7.0 was used for the thermodynamic calculation of multi component system of ferronickel slag and red mud. Liquid phase area was extended to lower temperature by adding red mud indicating its suitability as a flux material. X-ray diffraction analysis confirmed the dependency of the phase changes on the red mud content. Microscopic observation by scanning electron microscope (SEM / EDX) clarified the phase transformations from olivine to spinel along with red mud additions.INTRODUCTION Ferronickel smelting by submerged arc furnace (SAF) is an energy intensive process performed at high temperature range 1500–1600°C. During the smelting process of saprolitic nickel laterite ore with a nickel content of 2.2–2.3 pct, a large quantity of ferronickel slag is being produced that account for 97 pct of ore charged. To achieve ferronickel grade of 15–20 pct Ni, electrical energy of 80 to 85 MW is used for the melting and reduction of nickel oxide (NiO) and iron oxide (FeO) in the ore (Rodd et al., 2010). Unreduced components, mostly MgO, SiO2 and partly FeO are removed from the furnace in a liquid slag form by a tapping operation. Due to the high melting temperature, forsterite (Mg2SiO4) based slag containing approximately 10 pct FeO requires typical process temperature of 1600°C. Flux in metallurgical process is a medium that decreases melting and operating temperatures while it increases fluidity of the liquid slags. Calcite and fluorite are examples of flux materials used for the ironmaking, steel refining and continuous casting process. Oxide systems based on CaO - CaF2 - SiO2 - Al2O3 - MgO cover most of the slag composition in ferrous metallurgy accordingly. Crucial operating factors for ironmaking and steelmaking slags are basicity (typically CaO/SiO2 ratio), viscosity and impurity levels. These are extensively controlled by the fluxes. General metallurgical fluxes such as limestone, dolomite and calcium fluoride are abundant in nature and supplied to steel mills at low prices. Meanwhile, in copper flash smelting process, silica is supplied with copper concentrate to remove iron oxide (FeO) generated from sulfide oxidation. FeO - SiO2 binary system formulates eutectic area at 25–38 pct of silica that has low melting temperature below 1205°C. Fayalitic system (Fe2SiO4) that has low viscosity (0.1 Pa·s) (Park et al., 2011) facilitates easy separation of slags from molten sulfide mattes. Recently, copper plants actively utilize recycled raw materials as a flux. Various recycled glasses are ground and fed to copper smelting process as a partial replacement of silica ore. Applying industrial wastes to smelting processes is advantageous since the operators can reduce the production cost remarkably. Not to mention the consumption of recycled materials can ultimately minimize the environmental risks and the waste management costs. The authors, therefore, investigated the reasonable waste materials that can be effectively used for ferronickel smelting process. Prerequisites for potential fluxing materials are non-recyclable property, low transportation cost and excellent performance as a flux."

Jan 1, 2017

By Thom Mambe, Angelo Fernando

The objective of this work was to identify key parameters related to the reduction of the sulphur content in ammonium diuranate (ADU), and the identification of solid products being formed under various operating conditions. A laboratory-scale, continuous ADU precipitation circuit was assembled using a glass reactor vessel immersed in a temperature-controlled water bath. A pre-prepared uranium feed solution was fed continuously using a peristaltic pump. Anhydrous ammonia mixed with compressed air was metered and pumped using a double-headed peristaltic pump. An over-head mixer was used to keep the solids in suspension. The precipitated ADU slurry was removed from the reactor at the same flow rate as the feed solution. The slurry was sampled to generate ADU solids for chemical and physical analysis after four hours of continuous operation to ensure steady-state conditions. The following variables were studied to determine their influence on the sulphur content in the resulting ADU. (a) sulphate:uranium molar ratio in the reactor (1:1, 1:5, 1:10 and 1:20) (b) precipitation pH ( pH 6, 6.5, 6.9, 7.5 and 9) and (c) precipitation temperature (40C and 60C) A total of 18 tests covering the above parameters were conducted, and the results indicated that the sulphur content in the resulting solids was highly dependent on the reaction pH. Out of the pH levels tested, tests completed at pH 6.9 and 7.5 generated solids containing the lowest sulphur contents, between 0.5 to 1.5% S uranium basis (UB). The sulphur content in solids was found to vary linearly with the sulphate:uranium ratio in the feed solution, showing a statistically valid correlation. The impact of temperature was minor between 40°C and 60°C, with a slight advantage at higher temperatures. Tests at a sulphate:uranium ratio of 1:1 produced solids with the lowest sulphur contents. The influence of pH or temperature on sulphur content in solids was almost non-existent at this sulphate:uranium ratio. Precipitation pH is the major factor influencing ADU sulphur content, followed by the uranium to sulphate ratio.

Jan 1, 2020

By J. Keith Haddock

"The Luscar Mine is a metallurgical coal mine located in the foothills of the Canadian Rockies, 41 km southeast of Hinton, Alberta. The mine is operated by Cardinal River Coals Ltd., a 50/50 joint venture between Luscar Ltd. and Consolidation Coal Company of Canada. The mine produces a high quality medium volatile metallurgical coal which is sold on the export market principally to Japan and South Korea. Operations consist of a surface mine with capacity to produce 3.0 million tonnes per year and an underground mine which is currently mothballed due to market conditions.GeologyBedrock units within the Luscar minesite are of Devonian to Upper Cretaceous age. The commercial coal measures in the area are, however, confined within the Lower Luscar Formation. The Luscar Formation consists of a 460-metre thick sequence of interbedded sandstones, shales and coal seams. The sequence is primarily deltaic in origin, and is bounded to the north and south at the Luscar mine by tectonically induced thrust faulting.The only mineable coal seam at Luscar is referred to locally as the Jewel seam. Average thickness of this coal measure is usually 10.5 m to 14 m, although in some areas folding and faulting has produced ""pods"" of coal from 15 m to over 40 m thick while in others the structural deformation has thinned the coal to 3.0 m to 4.6 m. Waste within the Jewel seam seldom exceeds a metre of shale, carbonaceous shale or infrequent sandstone stringers.Reserves and Coal QualityProven surface mineable reserves, based on pit scheduling through 1996, are 50.8 million raw tonnes. An additional 19.2 million raw tonnes are contained in possible extensions to the present planned operations. These surface mineable reserves are considered to be those reserves within 155 m of the surface. Underground reserves, located within 770 m of the surface show that 25.7 million raw tonnes have been proven to date in additon to 27 .5 million indicated and 260 miIJion inferred.Coal specification at Luscar Mine is as follows:"

Jan 1, 1985