Search Documents

By Y. Rama Murthy, Amit Ranjan, Pankaj Satija, Sunil K. Tripathy

"Chromite ore is one of the essential raw materials for ferroalloy and steel industry. Boula-Nuasahi belt of Sukinda region, Odisha, is the only resource of chrome ore in India. The Indian deposits are typically characterized as ferruginous and siliceous type ores. Chrome ore is generally mined by open cast mechanized mining method in these areas. The run-off-mine (ROM) ore from the various mines is sent to beneficiation plant via stack yard for further up gradation. The chrome ore beneficiation plant (COB) has two major circuits: comminution (feed preparation) circuit and beneficiation circuit. In the comminution circuit, the ore is reduced to <1 mm size ( for complete liberation of chromite) from -220 mm size in stage wise crushing (primary and secondary crusher) followed by screening and single stage grinding in a ball mill. Fraction having size <1 mm is further upgraded in the beneficiation circuit to produce three different concentrates having specific chemical composition and Cr: Fe ratio. The beneficiation plant is a complex circuit comprising of combination of unit operations (spiral concentrator, Floatex density separator, hydrocyclone, wet shaking tables). In the recent years the overall performance efficiency (grade and recovery) of the beneficiation circuit got affected with numerous changes in the run-off-mine ore quality (physical and chemical), mineralogical composition, etc.In this article, attempts made for improving the performance of chrome ore beneficiation circuit is discussed. The approach adopted and practical problems encountered while the process were also highlighted. The results of the trials has shown an improvement in the performance of the cyclone (d50 : 56 µm – 40 µm) and chromite losses into tailing to <12%.INTRODUCTIONChromite has a wide range of application, from refractories to metallurgical industries, and from chemical to non-ferrous alloy industries. Chromium ore (Fe2+, Mg) [Cr, Al, Fe3+]2O4) occurs exclusively in rocks formed by the intrusion and solidification of molten lava or magma which is very rich in the heavy, iron containing minerals such as pyroxene and olivine. With the richness of silica and iron, the chrome ores are broadly classified as siliceous type and ferruginous type. Pure chromite with composition FeCr2O4 is rare because magnesium usually substitutes for ferrous ion and aluminum and ferrous ion substitutes for chromium. Generally the associated gangue minerals are talc, quartz, hematite, goethite, limonite, gabro, serpentine, anorthosite, dunite, pyroxinite, etc. Around 96% of the chromite ore production is consumed for metallurgical applications of which 94% is converted into different grades of ferrochrome i.e., high carbon ferrochrome and charge chrome as shown in Figure 1. Stainless steel being the leading consumer of ferrochrome, any change in the dynamics of the stainless steel industry impacts overall chrome ore demands significantly."

Jan 1, 2016

By D. G. Minnes

Many non-metallic minerals and structural materials are produced in Ontario to serve the needs of domestic manufacturers and export markets. In 1982 production was estimated to have a value of $765 million. Approximately 81 per cent of this was represented by structural materials, nearly 12.8 per cent by salt, and the remainder was other industrial minerals. Total mineral production in Ontario in 1982 was estimated at $3 .16 billion, down nearly $1.5 billion from 1980's high of $4.58 billion.

Jan 1, 1984

By C. D. Rowe, H. S. Mitri, J. Malki, I. Vennes

Ore extraction at great depths creates high stresses around mine openings, which can result in violent rock failure in one of various forms of strainburst. This is especially true with strong and brittle rocks, which can store a large amount of strain energy that is suddenly released at failure. The strength and brittleness of rocks have been extensively investigated in the past. The most widely accepted method for the determination of rock burstability is the strain energy storage index obtained from a non-destructive uniaxial load–unload test. However, the results of this method are not always conclusive, showing less repeatability when the target test load is changed. This study concerns itself with the introduction of microscopic analysis as a tool to help validate the strain energy index results when burstability cannot be warranted based on mechanical property tests alone. In this study, two types of rocks, namely, basaltic komatiite (BK) and felsic norite (FNOR) obtained from Canadian underground mines are examined. The selection is based on the premise that felsic norite is known to be burstable from the mine experience, whereas basaltic komatiite is not necessarily burstable. A total of 60 mechanical properties tests were conducted including uniaxial compressive strength, Brazilian tensile strength, and load-unload tests. Laboratory tests on FNOR consistently exhibit high burstability; however, the results for the BK tests are not conclusive. To seek explanations for the mechanical rock behavior, 18 thin sections were examined with optical microscopy and image analysis. The findings show the tested BK specimens are dominated by alteration products, and all primary igneous minerals are lost. There is minor quartz, garnet, carbonate minerals, talc, and serpentine, which give the rock its ductile properties. The FNOR specimens are found to be relatively fresh and supported by a strong network of plagioclase with minor pyroxene, biotite, and secondary micas, explaining the higher stiffness. This study demonstrates how optical microscopy can complement mechanical property tests to evaluate burstability of rocks.

May 4, 2025

By S. B. Mishra

Ni-20Cr metallic coating was deposited on a Ni-based Superalloy (3Fe-19.5Cr¬0.3Ti-Balance Ni) by a shrouded plasma spray process; NiCrA1Y was used as a bond coat. Erosion studies were conducted on uncoated and plasma-spray coated superalloy specimens using an air-jet erosion test rig at a velocity of 40 m/s and impingement angles of 30° and 90°. The coating has been characterized for porosity, microhardness and microstructure and X-Ray Diffraction (XRD). An electron probe micro analyzer (EPMA) was used to obtain X-ray elemental mappings of the coating along the cross-section. Scanning electron microscope (SEM) with EDAX attachment was used to analyze the eroded surfaces.

Jan 1, 2005

By L. Yuan, J. Qin, J. Xie, Q. D. Qu, Y. P. Liang

"This paper presents key outcomes of a major Asia-Pacific Partnership project between the Commonwealth Scientific and Industrial Research Organisation and Huainan Mining Industry Group Co. Ltd. to develop and demonstrate advanced technologies at Pansan mine, Huainan, China. A comprehensive approach assessed fundamental strata and coal seam methane conditions during mining and optimized mining sequences and coal mine methane capture systems. The project demonstrated a practical approach and procedures for advanced coal and methane co-extraction systems, improved mining safety and efficiency, increased methane capture and use, and reduced fugitive methane emissions.RÉSUMÉ Le présent article donne les principaux résultats d’un grand projet de partenariat Asie- Pacifique entre le CSIRO (Commonwealth Scientific and Industrial Research Organisation) [Organisation de recherche scientifique et industrielle du Commonwealth australien] et le Huainan Mining Industry Group Co. Ltd.; ce projet cherche à développer et à démontrer des technologies avancées à la mine Pansan, à Huainan, en Chine. Une perspective globale a évalué les conditions fondamentales des strates et du méthane dans les couches de charbon durant l’exploitation et a optimisé les séquences d’extraction et les systèmes de captage du méthane dans les mines de charbon. Le projet a permis de démontrer une approche pratique et des procédures pour des systèmes avancés d’extraction conjointe du charbon et du méthane, pour améliorer la sécurité et l’efficacité minières, accroître le captage et l’utilisation du méthane et réduire les émissions fugitives de méthane."

Jan 1, 2015

By G. M. Humphrey

It is a great honour and privilege to be here in this distinguished company of the outstanding men in the mining industry and the political life of Canada. I fully recognize that I am so honoured as a symbol of the combination of American and Canadian leaders in industry who are partners in the sponsor-ship of the Quebec-Labrador iron-ore mining development which we are undertaking, and as such I want to express our great appreciation of the co-operation and assistance we have met on every hand in Canada, and the genuine friendliness and never-failing courtesy which we are always accorded. We are quite aware that it springs primarily from the very high regard in which our partner and sponsor, Jules Timmins, and our other Canadian associates are held. Their high standing among you is well known and we quite naturally fall heir to the benefits of the great esteem in which you hold them. Jules Timmins and his long-time associate, John Knox, were the original inspiration for our participation in this venture. It was their enthusiasm and vision which caught our interest and led to our joining with them in the years of exploration and search which have brought us to the threshold of this great development where we stand today. So much has been written of the details of our exploration and plans for future development that it would bore you for me to review them further here, but there is a phase of this development, and an extremely important phase of it, which I think has passed almost unnoticed and which it may be well worth while for me to bring to your attention this evening.

Jan 1, 1951

By Charles Camsell

At the Annual General Meeting of the Institute in 1924. I endeavoured to present the position held by the mineral industries in the commercial life of this country. The facts and figures were presented at that time in a detached way. Since then, however, I have made some attempt to analyze them in order to determine the causes for that position and to draw some conclusions as to the future of the mining industry. As everyone knows, our trade figures are very often used in political discussion, especially in discussion of tariff policy. It would be entirely out of order for me to say anything touching the tariff issue and I want to have it clearly understood that, in my opinion, the material I am about to present contains not a single statement or conclusion which anyone would be warranted in using as an argument for either a lower or a higher tariff or for tariff changes of any kind. As a starting point, let me re-state, very sketchily, Canada&apos;s general situation in external trade. In the last calendar year, 1924, we sold Canadian merchandise of all kinds to other countries to the value of $1,045,000,000 in round figures. Our purchases abroad reached about $893,000,000. Thus our sales exceeded our purchases by roughly $152,000,000. In other words, we had what is known as a &apos;favourable balance of trade&apos; - one of the biggest favourable balances we have ever had in our history. The proceeds of our sales of Canadian products enabled us to meet the bills for all our purchases of foreign commodities and, in addition, placed a large surplus to our credit with which to offset our interest charges and other obligations abroad.

Jan 1, 1925

By Masakazu Daté

Moisture effect has been studied for the CO oxidation over Au/TiO2, Au/Al2O3 and Au/SiO2, in the range of H2O concentration over four orders of magnitude. It has been found that the catalytic activity is generally enhanced by moisture in the reactant gas. The enhancement is as large as two orders of magnitude. Response to the moisture concentration, however, depends on the support oxide, indicating different contributions of the support to the reaction steps. The moisture effect is reversible and the activity is mainly determined by the amount of moisture absorbed by the catalyst. The apparent activation energies are not significantly influenced by moisture for Au/TiO2 and Au/Al2O3. On the contrary, non-uniform conversion curves versus temperature observed for Au/SiO2 are drastically changed, which indicates that the reaction over Au/SiO2 does not take place at low temperatures without moisture. The moisture effect may be probably attributed to the decomposition of carbonate species accumulated during the reaction, while the ?OH group might directly participate in the reaction pathways as a promoter.

Oct 1, 2003

By R. Boom

Corus Umuiden, formerly Hoogovens, was the first steel plant in Europe after Voest to introduce oxygen steelmaking. In the decision-making process contacts with Dofasco in Canada about the production of formability steel grades were crucial. In developing oxygen (LD-) steelmaking high liquid steel output rates had to be combined with accurate process control. For ingot casting static models with input control and sampling during interrupted blowing were sufficient to deliver liquid steel within the required carbon, phosphorus, sulphur and temperature windows. Computers were introduced to perform the complicated charge calculations. Continuous casting called for strict control of composition and temperature at process end point and made predictable timing crucial. Dynamic control was introduced based upon sub lance measurements and waste gas analysis. Reliable disposable measurement sensors were developed in a concerted international action. Dissolved oxygen at blow end deteriorated the quality of low carbon aluminium killed steel grades. Blowing gases through the converter bottom improved process kinetics, resulting in lower carbon-oxygen products, yield increase and better phosphorus removal and generated new families of hybrid blowing processes. Introduction of secondary metallurgy facilities such as argon stirring stations, vacuum degassers and ladle furnaces relieved the demands for strict BOF end point control. Desulphurisation of hot metal became standard practice. In regions with scrap shortage hot metal desiliconisation followed by dephosphorisation, was introduced in the blast furnace cast house and hot metal transfer ladles. Later redundant converter vessels were used for pre-treatment, resulting in a two-stage process. The fundamentals of oxygen steelmaking are described and a vision on the future is presented.

Jan 1, 2004

By J. Baz-Dresch

"The most cost-effective method of placement of the high strength fill used in the Cannon Mine&apos; s overhand cut-and-f ill bench stopes was determined to be truck haulage. Constraint s imposed by the mine layout dictated the use of a truck which could dump its load in a fifteen-foot high drift. The Dux Teledumper truck was selected as the most suitable unit for this application based upon operational and maintenance parameters which included a telescoping, tilting dump box; large load capacity; and robust construction. Development of the truck continues through the cooperation between the manufacturer and user. INTRODUCTIONThe Cannon Mine is situated in the centre of Washington state, approximately midway between the cities of Spokane on the east and Seattle on the west. The mine complex is located three block s south of the Wenatchee city limits at the eastern base of the Cascade Mountain range.Asam era Minerals (U.S.) Inc., with 5I% ownership, operates the Cannon Mine. Breakwater Resources, Ltd. holds the remaining 49%.Annual paroduction is 520 000 tons per year, presently on a 21-shift per week operating schedule for both the mine and the mill.All production is presently won by overhand bench stoping with backfill. Stoping starts with 15-ft high by 24- or 30-ft wide sill cuts driven above and below a stope block . A drop rai se and slot are used to open a bench which is then slabbed toward the open slot. Truck-placed backfill is dumped into the mined - out stope from the upper sill cut. This stoping sequence is repeated until the top of the ore block is reached . The top sill cut is then tightly filled with backfill to minimize subsidence and to provide adequate roof support during extraction of the pillars.Mining equipment consists of hydraulic drills and rubber-tired, diesel scoops and trucks."

Jan 1, 1989

By A. Haque

"This paper describes an improved formulation of an analytical shear strength model developed by Haque & Kodikara (2012) by incorporating the failure of regular concrete/rock joints subjected to CNS condition. Sokolovskii’s analytical solutions developed for failure stress of slopes have been found to be effective in this regard. The analytical models have been validated for predicting the shear behaviour of concrete/rock joints subjected to various CNS loading conditions. The model has been found to accurately predict the dilation, normal stress and shear stress behaviour for a regular triangular saw-tooth joint up to the peak shear stress. Moreover, the peak shear stresses of concrete-rock joints with asperity angles ranging from 5 to 27.5o compared reasonably well with the available laboratory test results.INTRODUCTIONA new shear strength model for elastic regular triangular concrete/rock joints loaded under Constant Normal Stiffness (CNS) boundary condition has been developed by Haque & Kodikara (2012). The salient feature of this model is its capability of accurately estimating the normal and shear stresses of joints with shear displacements under CNS condition by incorporating the elastic deformation of asperities. However, the shear strength model of Haque & Kodikara (2012) for the elastic asperities cannot be directly employed to predict the peak shear stress of a joint experiencing plasticity under applied loads. Therefore, the model inevitability requires articulation of an appropriate shear failure criterion simulating the boundary conditions of the loaded asperity to predict the peak shear stress and corresponding normal stress and dilation behaviour of concrete/rock joints. Sokolovskii (1960) developed a set of analytical solutions for failure stress of slopes comprising c-??soils, which can be exploited effectively to simulate the failure condition as encountered for loaded regular triangular concrete/rock joints (Seidel & Haberfield, 2002)."

Jan 1, 2015

By M. Hozayen, Q. Ni, E. S. Radwan, P. Nawrocki, A. Jebbouri

"A major geomechanical study was conducted for one of the UAE onshore oil fields with the purpose of studying reservoir rock properties and stress distribution, based on which a 3D coupled reservoir geomechanical model was built. This model was later used for wellbore stability analysis and for analyzing the effect of fractures on future reservoir production performance, including fracture deformation and permeability evolution occurring due to reservoir depletion and resulting changes in local stress field. The subject of this study was a complex fractured Upper Cretaceous carbonate reservoir characterized by high degree of heterogeneity, both vertically and laterally. Wellbore instability related drilling problems were encountered while drilling the wells in this field. The problems were mainly in drilling the horizontal wells, including breakouts and mud losses. Experimental results of laboratory tests used in this study are summarized in Part I of this paper whereas wellbore stability analysis and formulation of a3D geomechanical model that was built for that purpose is summarized herein.A 3D geomechanical reservoir model was developed, which included natural fractures. The mechanical properties of the reservoir rock, such as Young’s modulus, Poisson’s ratio, UCS, friction angle and tensile strength were populated based on the correlations established in Part I of this paper and the developed model was then used to simulate the 3D mechanical-property distribution and the evolution of the in situ stresses in the field due to depletion from 1983 to present-day. Based on the full field model, mud weight cubes were developed to predict the safe mud weight windows in different drilling directions. In addition, well stability prediction for two planned wells was performed using a 3D near-borehole model. Firstly, the computed stress state and mechanical properties simulated in the full field model were extracted along the well trajectory of an existing horizontal well which was drilled recently and then, a3D near-borehole model was constructed along the well trajectory. The wellbore stability analysis along the well trajectory, including stress state, strain distribution and displacements, was performed to identify the instability events along the well trajectory. It has been seen that the presence of natural fractures is closely related to the recorded borehole instability incidents. The computed plastic strains which indicate the wellbore failure were consistent with the recorded wellbore instability events in the FMI image logs, what provide further verification of the developed model. Then, this 3D near-borehole model was applied to two planned horizontal wells and the wellbore stability analysis for the two wells was carried out.The results showed that drilling vertically in the reservoir is safer than drilling horizontally. However, the drilling mud weight window in the vertical direction is narrow, being as narrow as 18.7 pcf or 0.299 sg locally. Drilling horizontally is less stable towards the maximum far field stress direction than towards the minimum far field stress direction. The mud weight cubes were used to identify the optimal well placement and well trajectory. For planned well trajectories, this technology can also be used to determine the optimal mud weight."

Jan 1, 2015

By Daniel B. Leznoff

The cyanoaurate anions [Au(CN)2]- and [Au(CN)4]- are shown to be useful building blocks for synthesizing supramolecular coordination polymers. For the gold(I) unit, aurophilic interactions often increase the structural dimensionality of the system and can impart increased thermal stability to the metal-polymers produced. A series of polymers of the form M[Au(CN)2]2(Ligand)x have also been prepared and show large colour changes upon changing the ligand, thus illustrating a sensor-type application. Both building blocks can mediate significant antiferromagnetic and ferromagnetic interactions between transition-metal centres in the polymers. For the gold(III) unit, no metal-metal interactions are observed, although weak Au-N(cyano) interactions control the intermolecular packing. Several structural examples of cyanoaurate-based coordination polymers are presented, including 2-D and 3-D arrays and a supramolecular square.

Oct 1, 2003

By C. H. Hopper

DIAMOND drills have played an important part in the development of mines for many years. Recently. they have also entered the production field arid the use of diamond drills m the primary breaking of ores has become a big branch of the industry. The writer has estimated roughly that the total diamond drilling in Canada during 1942 was 5,625,000 feet, of which 2,250,000 feet, or 40 per cent, was for blast-holes. This accounts for 6,750,000 tons of ore broken, using the conservative factor of 3 tons per foot of hole. Many consider that the use of diamond drills for blast-holes is the most important advance in mine practice of the past decade, and the industry owes a great deal to the staff of Noranda Mines, Limited, for the pioneering they have done in the development of long-hole mining methods and for publishing their results. A great many mines have followed Noranda&apos;s lead. At the Waite-Amulet, Aldermac, Flin Flon, Canadian Malartic, Hoyle, and Matachewan Consolidated mines, most of the ore is broken by long-hole blasting. While the mines were developing new methods, the diamond-drill industry was developing mechanically-set bits and better machines. Through the effective use o smaller, cheaper diamonds, as well as more efficient setting, bit costs per foot are only one-half what they were ten years ago. Few people realize that a diamond bit is relatively inexpensive. The common EXT coring bit, for example, contains some 200 small diamonds, weighing altogether about 2.70 carats which, at $3.40 per carat, cost $9.20. After use, the equivalent of about 100 of these diamonds may be recovered. Therefore the true cost of the bit is only $7.00, made up of $4.60, the cost of the diamonds lost, $2.00 for setting, and $0.40 tax. The trend in machines has been toward specialization for the different classes of rock in blast-hole work. Light, high-speed machines have been developed for soft ores and higher powered machines for hard ores.

Jan 1, 1943

By P. Ashtari

Influence of Sr and Mn single and combined additions on the modification of the Fe-containing intermetallic compounds and mechanical properties of Fe-rich AA319 aluminum alloys have been investigated, The microstructural features e,g, morphology of the Fe compounds and eutectic Si has been correlated to the mechanical properties, It was demonstrated that modification of the Fe compounds from the platelet ß-Al5FeSi to the Chinese script a-Al8Fe2Si compound improves the UTS and elongation of the alloys by 10.3% and 83.9%, respectively. Moreover, the simultaneous modification of the Fe compounds and eutectic Si increases the UTS and elongation of the alloys by 15,3% and 116,1%, respectively.

Jan 1, 2005

By A. Shaak

The town of Hedley is some 200 miles due east of Vancouver and lies in the bottom of the Similkameen River valley, at the junction of Twenty Mile creek, at about the 1,700-foot elevation above sea level. The Nickel Plate mine camp is on Nickel Plate mountain at an elevation of about 5,600 feet, four miles slightly east of north from Hedley, to which it is connected by 9 miles of road, and by 10,000 feet of tramway and electric railway. The latter is used both to transport the ore to the 275-ton mill at Hedley and to furnish the mine with supplies. History The Nickel Plate claim was staked in 1898 to cover the sole outcrop of the Nickel Plate system of orebodies. Soon afterwards it was optioned by the Marcus Daly interests of Butte and underground exploration commenced. Early exploration was successful, and a power plant, tramway, and mill were constructed. The mill began operations in 1904. Production under Daly control ensued from June, 1904, to August, 1909, and amounted to 167,000 tons. The Hedley Gold Mining Company was organized and commenced operations in 1909. The capacity of the mill was increased by stages to 200 tons and a steady production, except for short periods in winter, was maintained until 1930. By 1930, gold to the value of nearly $10,000,000 had been produced since the discovery in 1898. The South American Development Company optioned the property in 1932. Active exploration was conducted during 1933 and 1934 by the Kelowna Exploration Company, a subsidiary of the South American Development Company. This work was sufficiently successful that, coupled with the increase in the price of gold from $20.67 to $35.00 per ounce, production re-commenced in December, 1934, and continued uninterrupted until July, i946, when, along with all B.C. gold mines, a strike closed operations. Under the present ownership, the mill capacity was increased to 275 tons.

Jan 1, 1946

By H. Warren Newcomen, Dennis C. Martin

"This paper describes the investigation of a large, progressive slope failure on the southeast wall of the east pit at Highmont Mine, British Columbia Geotechnical investigation s consisted of geological and structural mapping, assessment of blasthole drilling records, review of rock core information, slope movement monitoring and back analysis of various possible failure modes. Climate records and mining history were also assessed to determine their relationship to slope movement .Analysis of movement monitoring records and geotechnical information indicates that the failure is deep seated. The upper portion of the failure surf ace occurs along clay filled discontinuities. The lower portion of the failure surf ace appears to occur through the highly altered rock mass. High groundwater pressures and mining at the toe of the slope are documented to have had a major influence on stability at various times during the failure. Stability analyses results are presented and possible remedial measures are discussed.IntroductionHighmont Mine is located near Logan Lake in the Highland Valley approximately 50 km southwest of Karnloops, British Columbia (Fig. I). Mining of the porphyry copper and molydenum ore bodies began in 1980. In May, 1983, when mining in the east pit had progressed to a depth of about 60 m (200 feet) , a failure (designated the Southeast Failure) began to develop in the southeast corner of the east pit. Subsequent mining to a depth of 110m (360 feet) was accompanied by frequent and substantial slope movements involving between 500000 and I 000 000 m3 of rock . The slope was monitored extensively to assess short-term movement trends for operational safety. Geological mapping, core logging and rock mechanics testing were used in conjunction with the long-term monitoring information to determine the failure mechanism, conduct stability analyses, assess the effects of instability on pit design and enable design and installation of remedial measures."

Jan 1, 1988

By H. Warren Newcomen, Dennis C. Martin

"This paper describes the investigation of a large, progressive slope failure on the southeast wall of the east pit at Highmont Mine, British Columbia Geotechnical investigation s consisted of geological and structural mapping, assessment of blasthole drilling records, review of rock core information, slope movement monitoring and back analysis of various possible failure modes. Climate records and mining history were also assessed to determine their relationship to slope movement.Analysis of movement monitoring records and geotechnical information indicates that the failure is deep seated. The upper portion of the failure surf ace occurs along clay filled discontinuities. The lower portion of the failure surf ace appears to occur through the highly altered rock mass. High groundwater pressures and mining at the toe of the slope are documented to have had a major influence on stability at various times during the failure. Stability analyses results are presented and possible remedial measures are discussed.IntroductionHighmont Mine is located near Logan Lake in the Highland Valley approximately 50 km southwest of Karnloops, British Columbia (Fig. I). Mining of the porphyry copper and molydenum ore bodies began in 1980. In May, 1983, when mining in the east pit had progressed to a depth of about 60 m (200 feet) , a failure (designated the Southeast Failure) began to develop in the southeast corner of the east pit. Subsequent mining to a depth of 110m (360 feet) was accompanied by frequent and substantial slope movements involving between 500000 and I 000 000 m3 of rock . The slope was monitored extensively to assess short-term movement trends for operational safety. Geological mapping, core logging and rock mechanics testing were used in conjunction with the long-term monitoring information to determine the failure mechanism, conduct stability analyses, assess the effects of instability on pit design and enable design and installation of remedial measures."

Jan 1, 1988

By F. Prescott, D. Hiam-Galvez, J. Hiam

Mines are frequently located in remote areas with little conventional employment and few opportunities for the existing population. The development and operation of the mines results in several years of intense activity followed by a near-complete reduction in employment and opportunities after the mines are closed. Designing Sustainable Prosperity (DSP) is a method for rectifying this situation by designing for long-term growth in areas that host mines. This process involves the participation of local and national governments, local community, mining companies, investors, academics and those with sector expertise. The mines will be the catalyst for regional sustainable development. If successful, long-term economic and environmental prosperity should be the result for the areas affected by mining and, in some instances, promoting the regions as centres of excellence for a particular industry. This paper will describe how the concept works using the copper producing region of Peru and Chile as an example. Designing sustainable prosperity starts by looking at regions based on the natural resources and skills available, the infrastructure and possible energy sources. Integrated natural resource models and innovative market studies, followed by education and skills requirements, are then established to determine the potential for the region and what needs to be done to realise the possibilities. INTRODUCTION Industry 4.0, or i4.0, dubs the fourth and current industrial revolution. Where previously they have been founded on ever-increasing consumption and production, i4.0 distinguishes itself by its partial focus on reducing resource intensity; lightweighting, energy efficiency, sensors and automation to improve resource efficiency. Industry 4.0 is an era of artificial intelligence, genome editing, biometrics, renewable energy, 3D printing, autonomous vehicles and the Internet of Things (Lu, 2017). These drivers represent key opportunities for the economic future of nations and regions.

Jan 1, 2019

By J. Carr

This paper discusses: (1) the need for Western Canadian coal in eastern Ontario Hydro plants; (2) design parameters-unit trains, year- &apos;round receiving from trains, and shipping (Great Lakes season); (3) equipment chosen-dumper-indexer, outhaul conveyor, yard belt, stacker, reclaimer, surge-bin feeders, shiploader, docking system and dust control; (4) foundation and soil conditions-dumper house, yard belt, surge bin and dock-piling-runway; (5) winter conditions- thaw shed, feeder, lump breaker, beltings (oil), and dust control and disposal; and (6) operations to date.

Jan 1, 1979