Search Documents

By K. M. Wild, C. D. Martin, F. Amann

"Argillaceous rock formations, in particular clay shales, are notorious for creating challenges in rock engineering. Due to their generally low hydraulic conductivity and their complete saturation in their natural state at depth, the behavior of clay shales is usually characterized by a strong hydro-mechanical coupling.This paper presents typical pore pressure responses monitored in different underground rock laboratories and explores alternative ways for their interpretation. The underpinning processes and their relevance are identified based on analytical and conceptual numerical models. Pore pressure monitoring data from Opalinus clay at the Mont Terri Underground laboratory, the Boom Clay at the Mol facility and the Callovo-Oxfordian clay in the Meuse/Haute–Marne URL show a similar pore-pressure response associated with stress changes accompanying tunnel construction although the tunnels were built in different rock types, at different locations, and under different in-situ conditions.The numerical analyses in this study shows that the pore pressure response around an excavation in low permeable clay shales may have different explanations. Pore pressure drops observed in the tunnel near field can theoretically be explained by both, a pure elastic response in an isotropic or anisotropic rock mass with an anisotropic stress state, or a inelastic response and related dilatancy. However, a comparison between the numerical models and the in-situ measurements revealed that the latter is more likely. This conclusion is justified by the observation that pore pressure drops occur significantly ahead of the tunnel face which is not the case in elastic numerical simulations. Pore pressure measurements in the far field, where failure processes are unlikely to occur, can only partly be explained by a linear poroelastic models. The introduction of an anisotropic material plays a key role in reproducing the responses, conceptually."

Jan 1, 2015

"5.1. IntroductionThe sample preparation requirements for bulk analyses of platinum-group elements (PGE) are different from the requirements for ore microscopy and in-situ analyses. It is necessary that the initial sample collection results in as representative a sample as possible for both types of analyses. Ingamells (1980) believes, however, that sampling is always imperfect and that there is no such thing as a truly representative sample. Once collected, the usual low content and irregularly dispersed nature of the PGE require that samples for bulk analyses be made as uniform as possible, whereas in samples for ore microscopy and in-situ analyses the PGE must be concentrated. Because of the generally high specific gravity of platinum-group minerals (PGM), certain precautions must be taken, such as mixing the sample material in the bags prior to opening.5.2. Preparation forBulk Analytical MethodsThe principal factors that determine the size of the sample required for a bulk analysis are grade, heterogeneity and grainsize. Initially, the grade and sample heterogeneity can only be estimated and a sampling methodology is developed with experience. It is essential at all times, however, that the assayers have information about the source of the sample and the purpose for the analysis. Information on the grain-size, which can only be obtained through mineralogical analysis, is also very important for PGE analyses, but, unfortunately, is often ignored.5.2.1. Samples fromUnconsolidated DepositsConcentrations of PGE may occur in eluvial deposits as well as in a large variety of alluvial deposits, including those of fluvial and glaciofluvial origin. These deposits are often difficult to map and sampling is further complicated by the wide range, from sand-size to boulders, of the non-POE-bearing constituents, and by the irregular distribution and shape of the ""pay streaks"". PGE concentrations in unconsolidated deposits are largely composed of resistant Pt-Fe and Os-Ir-Ru alloys (cf. Cabri and Harris, 1975 and Raicevic and Cabri, 1976), thus making comminution to the usual-150 to -200 mesh somewhat unreliable, due to the malleability of these alloys."

Jan 1, 1979

By The Staff

This is in direct contradiction to the generally accepted philosophy of tube-mill grinding, which is based upon an enormous amount of experiment carried on in different parts of the world. Personally, I have no faith in the reliability of these conclusions of the authors. (Incidentally, the two circuits compared consist of six mills each of which the change in the hook-up is only in the last three mills-in one case, these three mills are in closed circuit and in the other, open or series circuit. Hence the last three mills are alone responsible for the alleged improvement, which means that the improvement in these three mills amounts to at least 18.8 per cent). The value of these figures depends upon the reliability of the work, of the measurements and the calculations of the authors. As very little information is contained in this Addendum concerning the methods of the work and the details of the measurements, it is necessary, in order to form an estimate of this reliability, to study carefully the previous paper published in the July, 1940, BULLETIN(3). Referring to the original paper, the present paper has this to say (bottom of page 379): "Here it may be remarked that we have made more money for Lake Shore digging into and forming the report than in obtaining the figures and data, and so far have never gone back to work on it without a resulting Lake Shore profit". Let me state that I, so far, have never gone back to work on it without finding more discrepancies and inconsistencies and illogical reasoning. In my first contribution to the discussion of the first paper, which discussion was published on page 355 and following, in the July, 1941, BULLETIN, I pointed out discrepancies and inconsistencies and illogical reasoning.

Jan 1, 1942

By B. Zeifert, C. Martínez-Morales, A. Romero-Serrano, A. Pineda-Rivera, H. Martínez-Gutiérrez, G. Diaz-Sandi

In this work, the effects of CaO/SiO2 ratio and the FeSO4 and FeS2 contents on the stability of the mineralogical species in chromium-based slags were studied. The chemical stability was evaluated by leaching with an acid solution. The main Cr-compounds in slags with FeSO4 and CaO/SiO2=1 were FeCr2O4 and Ca3Cr2Si3O12, while Cr3S4 predominated in slags with FeS2. The slags with CaO/SiO2=2 mainly contained CaCr2O4. The highest Cr concentration levels in the leaching liquors corresponded to slags with CaO/SiO2= 2, and the lowest Cr concentration corresponded to slags with high FeSO4 or FeS2, owing to the stable binding of chromium in the compounds FeCr2O4, Cr3S4 and FeS•Cr2O3.

Jan 1, 2011

By T. K. Akopyan, E. A. Naumova, V. V. Doroshenko, N. A. Belov

"A qualitative and quantitative analysis of the new Al-Ca-Mn-Fe phase diagram in the region of the aluminium corner is carried out using both thermodynamic calculations and experimental methods. Using the obtained data, the principal possibility of creating both cast and wrought sparingly alloyed aluminium alloys with calcium, manganese, scandium and zirconium at allowable iron contents of up to 0.4% that do not require solution treatment and quenching is justified. At the selected concentrations, the entire amount of manganese (1%) is practically included in the aluminium matrix, while calcium (~2%) and iron are in the multiphase eutectic, which has a fine structure. The joint introduction of 0.25% Zr and 0.1% Sc into the alloy leads to precipitation hardening due to the formation of the L12-Al3(Zr,Sc) phase during annealing. Based on the experimental data for the model multicomponent Al2CaMnFeZrSc alloy, it is shown that such alloys can combine high mechanical properties and good manufacturability during both casting and metal forming. This is due to the combination of a narrow temperature range of solidification with a fine eutectic structure.INTRODUCTION Hardening in branded aluminium alloys (both cast and wrought) is generally achieved by heat treatment of the T6 type, including quenching and artificial aging (Zolotorevskiy, 2007; Kaufman, 2004; Mondolfo, 1976). Heat treatment significantly increases the cost of the final products. Therefore, industrial companies are interested in developing alloys that can be hardened to the desired level without quenching. To solve this problem, alloys with scandium are the most suitable (Toropova, 1998; RØyset, 2005). This element (usually in an amount of ~0.3%) is one of the most effective hardeners in aluminium alloys, due to the formation of Al3Sc (L12) phase secondary precipitates, the size of which is less than 10 nm (Knipling, 2010; Fuller, 2005). These nanoparticles are formed during the annealing via decomposition of the supersaturated aluminium solid solution (hereinafter referred to as (Al)). This feature allows us to significantly increase the strength of aluminium alloys by simple annealing (at ~300°C), i.e., without heat treatment, including quenching. However, scandium is a very expensive metal, so its use as an additive is severely limited. The most effective method is the introduction of scandium together with zirconium (Lefebvre, 2009; Booth-Morrison, 2012). The optimal combination is the introduction of ~0.1% Sc together with 0.20–0.25% Zr, which, according to (Belov, 2006), gives approximately the same strengthening effect as the introduction of 0.3% Sc."

Jan 1, 2018

By Amauri Garcia, Rodrigo Valenzuela Reyes, Noé Cheung, José Eduardo Spinelli, Leonardo Fernandes Gomes, Rafael Kakitani

"The present research work deals with directional solidification (DS) of both Al-15wt.%Si and Al-15wt.%Si-1.5wt.%Mg alloys and further characterization of the related microstructures. The growth of refined primary Si and refined eutectic is well-known as positive in order to improve mechanical properties of the Al-Si based alloys. Alloying is also an effective method to strengthen the Al-Si based alloys, in which Mg is considered an important alloying element. However, lack of investigation regarding the effects of Mg on microstructure of these alloys is noted. So, in the present research work emphasis is given on both dendritic and eutectic growth being affected by solidification kinetics (V-growth rate and G-thermal gradient) during transient directional solidification. Experimental evolutions of microstructural spacing of both alloys have been determined which becomes possible to understand the effects of Mg coupled with the effects of growth rate on the final microstructural arrangements. A direct comparison of the tensile mechanical properties obtained for the alloys is also performed. It is shown by these correlations that the addition of Mg generally improves the tensile mechanical resistance with a minor decrease in ductility. Furthermore, the Scheil solidification path of the ternary Al-Si-Mg alloy was determined using the computational thermodynamics software Thermo-Calc, resulting in the following sequence of precipitation: Liquid-Si-a (Al)+Si- a(Al)+Si+Mg2Si. This sequence is compared with the experimental microstructure findings.INTRODUCTION Al-Si alloys containing from 4wt.% to 22wt.% Si comprise more than 90% of all Al-based castings. Parts manufactured with these alloys have a wide range of industrial applications due to their excellent castability, crack resistance, good corrosion resistance, good weldability, low density and high strength (Bray, 1976; Zolotorevsky, 2007; Reyes, 2017). Hypereutectic Al-Si alloys are widely used and researched in the automotive and aerospace sectors due to the low coefficient of thermal expansion, resistance at high temperatures, good wear resistance and high strength (Reyes, 2017; Tebib, 2013). Above the equilibrium eutectic composition (~12.5wt.%Si) the amount of primary Si particles becomes significant (Lasa, 2003). In the place of conventional hypoeutectic Al–Si, there is growing interest in hypereutectic Al–Si alloys as a candidate material for the high-quality engines because a higher volume fraction of silicon may bring about superior properties (Matsuura, 2003)"

Jan 1, 2017

By E. L. Martheleur

A general expression for the electric power generated or consumed in a direct-current circuit is obtained by multiplying the reading of a suitable voltmeter connected across the terminals by the reading of an ammeter connected in the circuit. by the reading of an ammeter connected in the circuit. When alternating currents are considered, the product of the volts and amperes as obtained for direct currents does not generally represent the true energy involved; it is greater than this true energy and should be multiplied by a certain factor which may have any value between zero and unity, according to the conditions of the circuit. This factor is called the power-factor of the system, and expresses the ratio of the true energy over the apparent energy. For a three-phase system the expression of the apparent energy is [\/ 3 x E x I; ] while the expression of the true energy, that is, energy suitable for mechanical work, is [v? 3 x E x I x cos A.] The total current of a circuit corresponds to the reading of an ammeter connected in the circuit; it is the resultant of two currents. The first of these is in phase with the voltage, and is that portion which really produces mechanical work; the second is always in quadrature with the voltage, that is it may lead or lag the voltage by 90° according to the condition of the circuit. This second current does not produce any sensible work, and for this reason is sometimes called wattless current or reactive current.

Jan 1, 1924

By R. B. Nourse, S. F. Gwynn-Jones, S. Nikolic, M. L. Bakker, I. McDougall, H. Joubert

"Tenova Pyromet’s core furnace knowhow and expertise has been built within the ferroalloy and nickel/platinum group metal (PGM) industries with the supply of electric furnaces for a number of nickel/PGM operators, including Eastplats, Lonmin, and Anglo-Platinum in South Africa, Mineraçào Serra Da Fortaleza in Brazil, and Norilsk Nickel in Russia. Tenova Pyromet has also supplied the electrode columns and associated electrode equipment – the heart of the electric furnace technology – for cobalt recovery in furnaces in Zambia and the Democratic Republic of the Congo. The quantity and size of projects undertaken by Tenova Pyromet has provided the opportunity to continuously improve furnace designs and the scope of supply, culminating in the most recent nickel/PGM project currently under construction at Northam Platinum. Through this innovative culture, the Tenova Pyromet Base Metals Initiative was formed in 2015 to develop the Novasmelt™ Furnace; a next generation optimised Top Submerged Lance (TSL) furnace design. The combination of Tenova Pyromet’s advanced Novasmelt™ product with our industry leading electric furnace technology are discussed with reference to applications for nickel and cobalt production. Flowsheet arrangements are compared summarising potential capital savings, operating requirements and achievement of downstream product quality.INTRODUCTION Tenova Pyromet is a leading player in the field of smelting technology development and equipment supply. Tenova Pyromet is the result of the union of three furnace suppliers under the Tenova banner: Techint Technologies (Tagliaferri), Core Furnace Systems Corp (Lectromelt) and Pyromet Technologies. The furnace experience of the combined groups dates back over a century with the earliest Lectromelt going into production in the early 1900s. Throughout the modern era, Tenova Pyromet has developed a reputation for providing dependable innovative smelting technology, high quality equipment and sound project execution to a worldwide client base with customer plants operating in Europe, Southern Africa, North America, South America, Russia, Kazakhstan, the Middle East, South Korea, and India. Tenova Pyromet’s core knowledge and expertise was developed in the South African ferroalloy, base metals, and platinum group metals (PGM) smelting industries. Tenova Pyromet has spent considerable effort on development and has contributed significantly to improve the state of the smelting industry. Tenova Pyromet’s electrode columns have become widely renowned and are now providing significant benefits, especially in increased furnace availability, to many smelting furnace operators. The electrode column is the heart of the furnace as it delivers a controlled amount of electrical energy, at an optimum depth in the burden/bath, to the smelting process. Every furnace is custom designed to the specific operating range and optimal operating point of that furnace and process"

Jan 1, 2017

By L. S. Brooks

TIMBER HANDLING presents a problem for any mine where appreciable amounts are used. This problem is accentuated where the shaft compartments are too small to allow a loaded timber truck to be lowered in the mine cage. When Normetal Mining Corporation, Limited, found it necessary to resort to square-set mining it faced this problem of getting large quantities of timber down a shaft that was also required for hoisting ore. A 'timber car' that could be suspended under the cage was developed to overcome this difficulty. Production started at the Normetal mine in 1937, at the rate of 250 tons per day. In 1938 a winze, known as No. 3 shaft, was sunk from the 800-foot level ?to the 1,385-foot level. This was later raised to surface and then deepened to 3,275 feet in three stages and became the main production shaft. The portion of the mine below the 3,070-foot level is serviced by a winze, locally referred to as No. 4 shaft, which has been developed for stoping down to the 3,990-foot level and which has been deepened to the 5,365-foot level. No. 3 shaft has two hoisting compartments, each 4 ft. 6 in. by 5 ft. 0 in. inside the timbers, through which the ?ore must be hoisted and timber and supplies lowered.

Jan 1, 1956

By N. A. McPherson, P. C. Stevens, A. J. Rigby

"There has been a consistent move in recent years to continuously cast small billets while utilizing ceramic stream protection between tundish and mould. The need to have ceramic stream protection has developed from a need to improve billet surface quality by submerged pouring. The need to protect the ladle to tundish stream in conjunction with tundish to mould protection is explained.The continuous casting of thin slabs is at the development state and will require a great deal of ceramic development to ensure the economic viability of the project. An insight is given to the main problems.IntroductionDuring the early development period o f the continuous casting of steel in the late 1940s and 1950s, much of the work was carried out on small cross section products. For example, the continuous casting of 50 mm square billets was carried out on a production scale in the United Kingdom at Barrow. Slab casting was initiated on a production basis on 100 mm thick stainless steel slabs at Atlas Steel, Weiland, Ontario. In the case of slab casting the thickness increased gradually until it was similar to Slabbing Mill feedstock , i.e. in the range 200 mm to 250 mm , although stainless steel continued to be lower at around 185 mm thick.For billets , a significant proportion of steel is now cast at around 100 mm square which creates specific difficulties when casting with a submerged pour - mould powder practice. The move back to smaller cross sections is further emphasized by the current interest in "" Near Net Shape Casting"" . If this move continues, then significant development will be required to create the refractories used between tundish and mould in the continuous casting process.Two specific areas which will receive attention are; (I) the casting of small cross section billet s; and (2) the casting of thin slab."

Jan 1, 1990

By T. C. Rao, Deb Kanungo

"The results of tests carried out on a 3-in. hydrocyclone have shown the linear relationships that exist between: (1) the flow-rate of water in the feed to and the overflow product from the cyclone; (2) the flow-rate of solids in the feed to and the underflow product from the cyclone. The underflow size distribution of an operation has been found to be linear and its usefulness in evaluating particle distribution in the cyclone has been discussed. Effects of design and operating variables on the above relationships have been discussed. The performance of this 3-in. hydrocyclone has been compared with that of a 20-in. cyclone, the results for which are available in the literature."

Jan 1, 1973

By Åke C. Rasmuson, Mahmood Alemrajabi, Kerstin M. Forsberg, Kivanc Korkmaz

"In the present study the recovery of a Panasonic Prismatic Module 6.5 Ah NiMH 7.2 V plastic casing hybrid electric vehicle (HEV) battery was investigated, separately processing the anode and cathode electrodes. The composition of the electrode materials was determined by total dissolution and analysis using ICP-OES. Nickel is the dominant metal in the active materials (65% by mass in the anode and 70% by mass in the cathode). Most of the rare earth elements (La, Ce, Nd, Pr and Y) are located in the anode active material, whereas only a small amount of Y is found in the cathode material. The electrode materials were further characterized by SEM-EDS and powder XRD. The electrodes were leached in sulfuric acid and in hydrochloric acid under different conditions. The dissolution was followed by taking out samples and analyzing the concentration of REE, Co, and Ni using ICP-OES. The results indicate that the dissolution of nickel could be limited by slow dissolution kinetics of nickel oxide. Further, it was found that light rare earths are lost through precipitation during sulfuric acid leaching with increasing extent as the temperature and sulfuric acid concentration increases. The separation of REE from the sulfuric acid leach liquor by precipitation as NaREE(SO4)2.H2O and from the hydrochloric acid leach solution as REE2(C2O4)3.xH2O have been studied by performing experiments using battery leach liquors. INTRODUCTIONIt is well known that the Hybrid Electric Vehicle (HEV) is becoming more common due to economic and environmental reasons. Batteries are widely used in HEVs’ such as automobiles or larger trucks for transportation purposes. The most common type of battery in these vehicles is nickel metal hydride (NiMH), largely due to Toyota's decision to use them in their popular Prius. More than two million hybrid cars worldwide are running with NiMH batteries, such as the Prius, Lexus (Toyota), Civic, Insight (Honda), and Fusion (Ford). Panasonic manufactures HEV prismatic NiMH batteries that have been used by Toyota and GM (among others), while Sanyo manufactures HEV cylindrical cell NiMH batteries, which have been used by Honda and Ford."

Jan 1, 2016

By L. Magne, M. Maldonado, R. Varela

Real-time optimization of flotation circuits demands for accurate and reliable measurements to support the decision making process. The collection zone gas holdup is an important variable in this context as integrates the effect of machine and chemical factors on the bubble size and velocity distributions. It has been demonstrated that gas holdup not only correlates with bubble surface area flux, which defines the particle collection rate and recovery in the collection zone, but also with water overflow, a variable which has been related to the froth zone recovery. Therefore, on-line gas holdup measurements provide a reliable alternative to judge efforts leading to the optimization of flotation cells and columns. Estimation of gas holdup in flotation from electrical conductivity measurements has been proposed and extensively used in lab and industrial installations. The approach is based on the application of Maxwell's model, which relates the concentration of a dispersed phase in a continuous medium to measurements of the conductivity of the liquid medium and of the mineral pulp with and without air bubbles included. These measurements require a conductivity cell which covers a representative volume of the flotation cell, and creates a homogeneous electric field throughout this volume that ideally is not affected by the conductivity of the medium. The development of such a cell in the limiting space and geometry of a laboratory flotation cell has been problematic, but a multi-electrode arrangement offers a promising alternative. Electrodes were installed in the flotation cell of a Denver unit; the results of preliminary testing are discussed with a focus on its performance in the measurement of two- and three-phase dispersion conductivity.

Jan 1, 2015

By K. J. Daun, C. J. Shi

UsiborThrough the second step heating at 900 °C, the spectral emissivity shows a gradually decreasing trend with increasing soak time, caused by the surface phase transformation from Al® 1500P coupons are austenitized in a Gleeble 3500 thermomechanical simulator using a two-step heating procedure in an argon atmosphere. Variations in spectral emissivity are measured in-situ using a near infrared spectrometer and ex-situ with a Fourier transform infrared reflectometer. Microstructural evolution and surface roughness are investigated using optical microscopy, FE-scanning electron microscopy, and a surface profilometer. A series of phase transformations of Al-Fe-Si intermetallic phases at the coating/steel substrate interface cause the surface phase and surface roughness to change, which in turn influences the spectral emissivity. At the beginning of the first heating step, the coupons have very low spectral emissivity, due to the molten Al-Si coating. Spectral emissivity increases significantly with increasing soak time from 5 to 12 minutes, associated with the surface phase transformation of the coating into Al7Fe2Si intermetallic phase and an increase in surface roughness. 5Fe2 into AlFe intermetallic phase with a decrease in surface roughness.

Jan 1, 2015

By James G. Lyons

All machines vibrate and make noise. An increase signals impending trouble. Vibration and noise analysis allows the condition of the machine to be determined without costly interruption in service for disassembly and physical inspection.

Jan 1, 1977

By E. O. T. Simpson

"IntroductionAS COMPARED with coal mines in the United States, and even with some of those in eastern Canada, the coal mines of western Canada, generally speaking, :have made little progress toward mechanization at the working faces. So far as Vancouver island is concerned, there are three main reasons for this : ( 1 ) in some areas, conditions• easy for hand-loading but unsuitable for mechanical loading make high outputs per man •possible by the former method; (2) faulting of the coal seams in ..some areas precludes long-term planning and the introduction and efficient use of expensive equipment; (3) thinness •and other characteristics of the seams in many areas favour hand-loading.No. 8 MINENo. 8 mine of Canadian Collieries (Dunsmuir), Limited, is located in the Cumberland sub-area of the Comox coalfield on Vancouver island about 90 miles west-northwest of Vancouver. The geological structure of this coalfield has been described by J. D. McKenzie. The seams occur in the Comox formation, a subdivision of the Upper Cretaceous Nanaimo Group. The formation is of near-shore origin and was laid down on an irregular surface of' older rocks. The irregular generally have a northeasterly dip, modified by gentile folds and by a •few large, and a number of smaller, faults.Four seams have been worked in the Cumberland area and all vary in thickness and in the amount and number of interstratified bone and rock •bands."

Jan 1, 1953

By J. R. Foster

Investigations into the effect of a variety of acid digestions on common rock-forming minerals demonstrated a considerable variation in the proportion of the total metal extracted. A similar situation applies to the analysis of a number of common rock types. In addition, grain-size variation has an effect on the amount extracted by certain digestions. This work indicates that considerable care needs to be given to selecting an appropriate acid digestion capable of determining metal held in particular components of a sample. By using partial extraction techniques, the identification of certain patterns of metal distribution, undetectable by normal methods involving total metal analysis, may be achieved.

Jan 1, 1973

By R. S. Douglas

THE Granby Consolidated Mining, Smelting and Power Company, Limited, is engaged in the mining and concentrating of copper ores, and, incidentally, in the mining of coal and the production of electric power. The Company has been engaged in these various operations both on the mainland of British Columbia and on Vancouver island for the past forty-five years. This paper will attempt to cover their present operations in the Similkameen mining district of southern interior British Columbia. GENERAL CHARACTER OF THE DISTRICT The Interior Plateau in southern British Columbia ranges in elevation from 3,000 feet to 6,000 feet. In the vicinity of Princet0n, a depression in the Plateau forms a well defined basin which is floored with a series of nearly flat-lying Tertiary sediments containing some workable seams of lignite. From this basin, the upland surface rises gradually t0ward the south, from an elevation of 2,000 feet at Princet0n to 4,000 feet at Copper mountain, and 6,000 feet in the upper parts of the Similkameen basin, where it merges into the rugged and diversified t0pography of the Cascade system, with glacier inhabited peaks rising to over 9,000 feet. The valleys of Similkameen river and its tributaries are wide, having flaring sides and gentle slopes, and are separated one from another by subdued rounded spurs, of which Copper mountain is typical. The drainage of this district is taken care of by Similkameen river and its larger tributaries, such as Pasayten river, and Wolfe, Friday, and Whipsaw creeks. The name Copper mountain is applied to a gently arched, nearly flat-topped spur between the deep valley of Similkameen river to the west and the shallower valley of Wolfe creek tO the east. The mountain is appro-priately named from the number of copper deposits occurring on its sides and summit, some of which have been developed int0 an important producer, known as the Copper Mountain mine.

Jan 1, 1943

By Lloyd F. Dunham

"Crucial to the implementation of new computer-based information systems at Sudbury Operations of Falconbridge Limited was a data communications network that would take computing power to the various mine and plant sites. Falconbridge required a capability to provide on-line data entry, inquiry, and reporting capabilities in three geographical areas, six mines, two mills, a smelter, approximately fifty shops, seven warehouses and numerous administrative offices throughout the Sudbury basin.Conventional cabling methods were rejected based on the projected cost of installation of necessary cables; lack of flexibility to meet the changing requirements of the mine environment; and the risk of losing service to an entire area depending on solitary communication lines.Instead, Falconbridge selected and installed a Data Carrier System (DCS) and Packet Switching Communication System from Teltone Limited, Markham, Ontario. This combined system ""piggy-backs"" computer data over voice-grade twisted pair wire, bringing data to the associated PBX equipment. From there data packets are assembled and routed to the central computer site where they are disassembled for entry into the host machine.Falconbridge has been successful in using existing technology to solve communications problems in a difficult environment. Plans for the future of this network will increase its utilization for technical and real time data communications in addition to the business systems workload it now handles. The Computer Services group in Sudbury is confident that the data highway will handle communications traffic well into the future.IntroductionIn late 1984, the Sudbury Operations of Falconbridge Limited undertook a review of their existing business computer systems. The results of this review indicated that there was an opportunity to improve the timeliness and quality of information coming from the existing computer-based systems while achieving an investment payback by undertaking the project. The greatest benefits from this project would be achieved if the computing tools could be delivered to the employees that were the day-to-day users of the data. Falconbridge's existing business systems were oriented to the batch mode of processing. An alternative solution to using the existing programs had to be found."

Jan 1, 1988

By P. J. Sylvester, D. H. C. Wilton, R. I. Wheeler, M. A. E. Huminick, D. Evans-Lamswood

"Abstract — Systematic characterization of the mineralogy of massive sulfide ore deposits can provide valuable insights into ore genesis and metallurgical processing that would not be apparent otherwise. We describe a method wherein (1) normative mineral abundances are calculated from whole-rock chemical assays using an algorithm, (2) the results are cast in block models, (3) the results are then verified with automated image analysis of a subset of samples prepared as grain mounts by backscattered electron imaging and X-ray mapping on a scanning electron microscope, and (4) those verified results are integrated with textural data determined by optical microscopy.The technique is applied to the magmatic Ni-Cu-Co sulfides of the Ovoid orebody, based on geochemical assays of 3175 whole-rock samples. Three principal ore zones are defined in the Ovoid. Type I ore occurs in the center of the deposit; it is magnetite-rich and pyrrhotite-poor with intermediate contents of pentlandite and chalcopyrite. Type II ore surrounds Type I ore and is pentlanditechalcopyrite- rich with intermediate contents of pyrrhotite and magnetite. Type III ore occurs at the base and along the outer periphery of the northern part of the orebody; it is pyrrhotite-rich and chalcopyrite- poor with an intermediate content of pentlandite, and a low-to-intermediate content of magnetite."

Jan 1, 2012