Search Documents

By A. M. Ramadan

The composition of phosphate rocks, mainly used in manufacturing fertilizers, varies among deposits; therefore, phosphate rocks from different sources are expected to behave differently in acidulation processes. This paper examines the effect of preconcentration of phosphate ore from El-Sebaiya East, Egypt, using flotation on uranium leaching. A high-grade ore sample (27.3% P2O5, 168 mg/kg U) supplied by the Al-Nasr Mining Company, was subjected to reverse single-stage flotation to separate carbonate from the phosphate sample. Subsequently, P2O5 and U concentrations were 32.2% (92.1% recovery) and 225 mg/kg, respectively. After the leach process, the U concentration in the liquor was 319 mg/L.

Jan 1, 2014

By David Lin

"Modal data from Red Dog Main Pit ores were collected and analysed on a size-by-size basis. The Main Pit data were compared to data from composite samples of Red Dog Aqqaluk ores. The data revealed that a large fraction of the sphalerite in the Aqqaluk baritic ore was tied up in sphalerite/galena binaries. This provided an explanation for its poor leadlzinc selectivity compared to Main Pit ores. The Aqqaluk vein ore exhibited levels of sphalerite/galena binaries comparable to that of Main Pit ores resulting in comparable lead/zinc selectivity.An attempt was made to correlate the modal and metallurgical data for Main Pit stockpiles. It was found that there was moderate correlation between the percentage of sphalerite locked in binaries with galena in the <C5>C6 size fi-action and sphalerite deportment to the leadconcentrate.INTRODUCTIONTeck Cominco’s Red Dog Mine in northern Alaska is one of the richest zinc districts in the world. Red Dog Mine has been in operation for over ten years and produces nearly 1 million tonnes of zinc concentrate per mum. Red Dog Mine is an open pit operation and current mining is conducted in the area known as the Main Pit. The Main Pit contains proven reserves of about 41 900 000 tonnes of ore grading 19.2% Zn and 5.2% Pb (Cominco 2000). To the north of the Main Pit is the Aqqaluk deposit. It contains probable reserves of 56 100 000 tonnes of ore grading 16.6% Zn and 4.1 % Pb. After the Main Pit has been exhausted, the Aqqaluk deposit will be exploited.The Aqqaluk deposit consists of three main geologic ore types: baritic, siliceous and vein. The siliceous ore type is dominant, representing 64% of the mineralisation. Composite samples of these ore types were created from drill core and batch flotation tests were performed on them. The flotation tests indicated that there were significant metallurgical differences between Main Pit ore and the Aqqaluk siliceous and baritic ore. The siliceous and baritic ores were found to suffer from poor lead/zinc selectivity (Lin 1999, G&T 1999). It was suspected that there were problems with the original Aqqaluk composite samples, thus a new set of composite samples were created and batch flotation tests were conducted again. In this set of tests, the new baritic ore still suffered from leadlzinc selectivity problems, but the new siliceous ore provided excellent metallurgical results. A summary of the flotation results is given in Table 1. Stockpile 132, which is typical of Main Pit ore, is given for comparison purposes. The mineral suite at Red Dog is relatively simple. The ore consists of galena, sphalerite and pyrite in a silicate matrix. The low zinc recoveries of the baritic ore were largely due to sphalerite losses to the lead concentrate."

Jan 1, 2002

Pressure for Better Safety Practices ? Increase Government Regulation ? Safety practices evolve from: ? Increased efficiency and performance ? More knowledgeable workforce ? Focus on decreasing risk to shareholder value In Order to achieve this ? Focus Points: ? Skill Development ? Best practices ? Situation-based decision making ? Enablers: ? Adoption of new technologies ? Transformed miner education ? Delivering on-demand information to the point of work Results: Miners empowered to improve mine safety

Aug 1, 2013

By H. Powell

"This paper discusses how elemental analysis of conveyed bulk flows in real time using PGNAA (Prompt Gamma Neutron Activation Analysis) technology has resulted in significant improvements in advancing plant control in mineral processing operations. PGNAA through belt, full stream, continuous, multi-elemental, real time analysis technology is explained. Capabilities and limitations in plant operating environments are discussed including comparison with other real time, on-line technologies through review of published information available for on-conveyor minerals applications. Case studies include an iron ore and copper-gold company, both of which consider the technology an essential component in advanced plant control necessary in new process flow sheet designs, rather than an optimisation tool.INTRODUCTION Process operators rely on supply of a reasonable ore quality and consistency from the mine. Unfortunately neither the mining nor process operators have much control over the ore quality once it has been put into the crusher. Grade control typically stops once the material is designated as ore and the process plant operator needs to process it irrespective of quality. Plant control is most effective when technologies measure process streams directly and preferably in real time. Measuring sampling streams that are not representative of the primary flow will result in incorrect plant control decisions. Sampling coarse conveyed flows is expensive and impractical at many operations, however, this does not mean those flows cannot be measured. Investigations to find techniques suitable for real time elemental analysis have focussed on the application of known laboratory techniques to process streams. For conveyed applications, development of neutron irradiation techniques were most promising and early studies indicated potential success for bauxite measurement (Beurton et al, 1995). Tran & Evans (2001) concluded there was no equivalent technology to PGNAA in terms of material penetration power and that the technology was eminently suitable for basic industries such as cement. Nelson and Riddle (2003) evaluated PGNAA for possible use in the phosphate industry by using a unit installed in a cement plant to test performance on phosphate samples and ultimately recommended its use for further characterisation of the mine’s various ore types to improve stockpile allocation and grade control"

Jan 1, 2014

By R. Holmestad, M. Gazizov, S. Wenner, R. Kaibyshev, J. K. Sunde

"Mechanical properties and microstructure of an Al-4.7Cu-0.74Mg-0.51Si-0.48Mn-0.10Cr-0.09Ti-0.02Fe (wt. %) alloy subjected to various thermomechanical processing (TMP) have been investigated and compared to conventional ageing at 170°C (designated T6). Three TMP routes involving cold deformation of solution treated samples were tested. These were (i) 3%-stretching (T8-3%), (ii) equal-channel angular pressing (ECAP) to true strain (e) of ~1 (T8-1) and (iii) ECAP to e~2 (T8-2), all with subsequent ageing at 170°C for 0-96 h. At peak age conditions, both yield stress, ultimate tensile strength and elongation-to-fracture decreased for the T8-3% state as compared to the T6 condition. Intermediate ECAP (T8-1 and T8-2) lead to significant increase in maximum yield stress, ultimate tensile strength and elongation-to-fracture. The changes in mechanical properties were related to microstructure evolution, encompassing changes in grain sizes, dislocation densities, precipitate morphology and phase fractions, which were characterised using transmission electron microscopy. Relations between TMP, precipitation behavior and contributions to different strengthening mechanisms are evaluated.INTRODUCTION Al-Cu-Mg-Si alloys are widely used as structural materials in aerospace industry due to their attractive combination of high specific strength, good fracture toughness and enhanced creep resistance. These properties are largely due to the formation of a large number of nano-sized metastable precipitates during artificial ageing (Polmear, 2006; Eskin, 2003; Gazizov, Dubina, Zhemchuzhnikova, & Kaibyshev, 2015). The precipitation behaviour in these alloys is complicated and depends among other things on Cu concentration and the Mg:Si ratio (Wolverton, 2001; Chakrabarti, & Laughlin, 2004). In general, the precipitation sequence has been presented in a prior study (Eskin, 2003) as follows:"

Jan 1, 2018

By P. Miranda, K. Le, G. Maes, R. Peters

"The Mount Milligan Mine, owned by Thompson Creek Metals Company Inc. (TCM), started operations in September of 2013. It is located between the communities of Fort St. James and Mackenzie and is the first major metal mine to open in British Columbia in 15 years. Based on reserves as of January 1, 2014, it has an estimated 22 year mine life with 2.1 billion pounds of copper and 6 million ounces of gold in reserves. Like all commissioning operations, there have been issues achieving design throughput and recovery due to flow sheet design, equipment failures, control philosophy, and reagent scheme. Efforts to improve overall mill performance include equipment modifications, reagent screening and testing, and grind size testing. Applying these changes to the mill and working closely with the mine has resulted in continuous improvement each month as Mount Milligan looks to achieve the nominal design capacity of 60,000 dry metric tonnes per day in the later part of 2015. Considerable focus is being placed into ensuring size reduction equipment is utilized effectively. Additional modifications and tests are being undertaken to steadily improve processes and alleviate restrictions in the mill. This paper will discuss the start-up and present ramp-up history of Mount Milligan, the current mill processes, and the steps taken to achieve expected production numbers.OPERATION BACKGROUNDMount Milligan is an open-pit copper and gold operation wholly owned and operated by Thompson Creek Metals. It is located approximately 155km northwest of Prince George, British Columbia, between the communities of Mackenzie and Fort St. James. The copper-gold porphyry deposit contains a Measured and Indicated Mineral Resource of 706.7 Mt at 0.18% Cu and 0.33 g/t Au, containing 2.84 billion lb. copper and 7.50 million oz. gold. Mine life is currently estimated at 22.1 years (“Feasibility Update – Mt. Milligan,” 2009). The mill is designed to process 60,000 dry metric tonnes per day and produce 400 dry metric tonnes of concentrate per day averaging 25.5% Cu and 40 ppm Au. Concentrate is delivered by truck and trailer to Mackenzie followed by rail to Vancouver for overseas shipping to various customers.Mount Milligan is considered a “zero discharge” operation meaning no process or surface water will be discharged to the environment. As well, stockpiling is very limited and is only permitted for a short period of time. This scenario presents several unique challenges. Scheduling of ore/waste production must be carefully planned as waste rock is used to build the tailings storage facility (TSF). Reagent selection is also important as persistent chemicals will have a tendency to build up in reclaim water which feeds the process water tank."

Jan 1, 2015

By Michael J. Lord, Richard H. O. Wagner

"The technologies used in the mineral processing of ores are being increasingly applied to the identification and remediation of metal contaminated industrial, military and landfill sites. The objective of mineral processing treatment of contaminated site material is to restore the value of the land and to concentrate the contaminants into a very small volume of separated material which, depending upon its nature, can be further processed, marketed, or sent to a landfill. A systematic characterisation of the site material is first undertaken. Bench and pilot testing follows to evaluate criteria for metal separation. The testing may examine one or more physical or physico-chemical reprocessing methods, singly or in combination, for the remediation of the test samples. These mineral processing tests determine the % metal removal fiom the soil and the contaminants concentrated from the medium. The usefulness of mineral processing testing for site remediation flowsheet design and execution is illustrated by the case studies presented. This paper will present the test results of three case studies: an industrial site decontamination, the cleanup of a small arms firing range, and the reclamation of property within a landfill.INTRODUCTIONEnvironmental legislation and our society’s quest for a cleaner environment has led to the application of mineral processing expertise and technology for industrial site decontamination, military site cleanup and landfill reclamation. Although the required level of decontamination varies between jurisdictions, a site becomes a candidate for decontamination once the contaminant concentrations are found to exceed the Canadian Council of Ministers of the Environment (CCME) Interim Remediation Criteria for soil (decommissioning guidelines) or applicable provincial guidelines. The objective of mineral processing treatment of contaminated site material is to restore the value of the land and to concentrate the contaminants into a very small volume of separated material which, depending upon its nature, can be further processed, marketed or disposed of in a landfill"

Jan 1, 1999

By S. Dessureault, J. Porter, M. Woodhall

Information and communication technology (ICT) is seen as a key source of future productivity improvements in mines. The information technology infrastructure (ITI) necessary to achieve these productivity improvements will come in the form of data integrated from multiple source systems throughout the mining value chain. Two pure approaches are available: supplier-controlled or operations controlled data structures; each strategy has its own advantages and disadvantages. Case studies involving the South African mining industry are used to demonstrate the advantages of using hybrid-controlled data structures. Depending on the level of operational control, new skills are also necessary to be learnt by mining professionals including: information engineering; creating consistent and quality data; and process improvement techniques that use the integrated data for improving the operation.

Jan 1, 2004

By G. Landry

"IntroductionThe Cape Breton Development Corporation (CBDC) is constantly searching for new technologies that will enhance the marketability of its coal. One technology which shows promise in utilizing Cape Breton coal while at the same time addressing the traditional problem of high sulphur inherent in the Sydney coalfield, is coal-water fuel (CWF).The CWF process incorporates a physical change of coal by grinding it to a flour-like consistency and then mixing additives with it to make a fine coal slurry. The result is a liquid dispersion of fine coal particles that looks like oil, stores and flows like oil but burns like coal. The equipment used in the CWF process is standard mineral processing equipment but application of the equipment to manufacture a specific coal particle size and the specified additives used in the mixing make it a unique technology.The product, which CBDC calls Carbofuel, consists of 70% coal, 29.5% water and 0.5% chemical additives. The key properties of the product are: (I) high solids loading, (2) medium viscosity levels, (3) stability against sedimentation, and (4) good atomization behaviour. Carbofuel specifications are presented in Table I. Carbofuel ProductionThe production of Carbofuel is based on the controlled processing of coal. This involves wet grinding of the coal to a specified fine size (-250 um), cleaning this fine product to remove mineral impurities and formulating (with chemical additives) a finalproduct from the cleaned coal. The flow diagram in Figure 1 indicates the processing circuit for Carbofuel production.CBDC operates a 7-tonne-per-hour continuous production plant complete with state-of-the-art control, full laboratory services, product storage and loadout facilities. The plant has operated since 1983 and has produced over 12000 tonnes for several major demonstrations. The plant is shown in Figure 2."

Jan 1, 1987

By Sanjiv Dhanjal

"Often mineralogy dictates the physical properties of a material rather than chemistry. This in turn affects how that material behaves in a process plant, and whether optimum conditions for refining one mineral are different to those for refining another. For example how does refining copper from chalcopyrite differ to refining copper from bornite?Minerals are naturally occurring inorganic solids that have a definite chemical composition and an ordered atomic (crystalline) structure. X-ray diffraction is a common and highly developed method to identify and quantify minerals. X-rays are fired onto a material and the mineral is identified by the angles where the diffracted X-rays are in phase.Most X-ray analyzers are laboratory based. A sample is prepared and analyzed by a detector that travels in an arc to collect the diffraction pattern. COSMA has a curved detector which picks up the complete x-ray pattern instantaneously. Therefore, material is collected and transported through the machine where is it is analyzed continuously.COSMA measures about 0.5 tons of material per day, while laboratory analyzers measure a few grams at a time. Real time data trends are produced allowing for improved process evaluation and automatic control. The COSMA on-line system has taken X-ray diffraction out of the laboratory into the field.There are a number of systems in operation in cement production. It is recognized that on-line mineral analysis has a role in many other processes. This paper presents the technology and invites further discussion should the technology be beneficial to members of the audience.INTRODUCTIONThis article describes COSMA, a system that provides direct and continuous on-line mineral analysis using X-ray diffraction in the field. While X-ray diffraction is a common technique used in mineral analysis, the time from sampling to analysis can be hours and plant operators typically do not get the data in time to control a process or respond to an upset. COSMA provides rapid measurement, analysis and feedback of data, in real time. This provides powerful information that can be used to optimize operation, thereby reducing costs and increasing quality."

Jan 1, 2009

By L. Garycki, P. Poks, R. Urbaniak, T. Gabka

In 2016 at Głogów Copper Smelter KGHM Polska Miedź S.A., after shutting down the shaft furnaces new FSF was launched. Currently, it is the only smelter with two direct to blister flash smelting furnaces in operation. The main difference between the vessels are the dimensions and production capacity. The new furnace design output is about 30% higher compared to the old flash smelting furnace working for 40 years. The paper presents a comparison of both FSFs operation, differences in technology and the way to optimize the process to maximize efficiency. INTRODUCTION KGHM Polska Miedź S.A. is the only company in Poland (eastern part of Europe) that extracts and processes copper ores. It is located in the south west of Poland and this region is called the "Copper Basin”. KGHM PM S.A. consists of three underground mines: Lubin, Polkowice-Sieroszowice, Rudna, concentrator plants, a tailings pond plant, three copper plants: Legnica, Głogów and Cedynia wire rod plant in Orsk. The publication relates to the operation of the furnaces in Głogów (the plant in Głogów consists of Głogów 1 and Głogów 2 which form integrated smelting and refining facilities). In 2016, after closure of the shaft furnaces technologies in the Głogów 1, a new FSF commenced operation. The simplified process flow sheets are given in Figure 1 and 2. Technological schemes are similar, but due to the differences in them, they will be discussed separately. Głogów 1 Enriched ores are discharged and directed to the feed preparation plant. Delivered concentrates are built up on the three bedding aisles in appropriate proportions. The concentrates are distributed in even layers in one of the three aisles. Aisle emptying is done with a blending machine which cuts across the concentrate layers and collects thus blended material, sending it via belt conveyors to a storage bin. From the cross- blending machine and conveyor assembly, the mixture of concentrates is directed to drying in the steam dryer. Part of the charge is directed to the FSF and part to the roaster for carbon elimination. Known in the world roasters are used to eliminate sulfur compounds or arsenic. In the case of KGHM deposits, the aim of the process is to reduce the energy value of the feed by eliminating carbon and converting sulfur from sulfide to sulfate. Changing the nature of exothermic to endothermic material is crucial in the case of furnace operation with design performance. Roaster is a separate furnace with an innovative character.

Jan 1, 2019

By A. Sinha, N. K. Babar, H. R. Kalihari, A. K. Chakraborty, M. R. Saharan, C. P. N. Pathak

A case study is presented on the optimization of cable bolting patterns in cut-and-fill stopes at the Chikla Mine, MOIL, India. Rock mass characterization, using Bieniawski’s RMR and Barton’s Q, indicated that the stopes lie in the “no supports required” to “spot bolting required” support categories. In contrast, the current practice of cable bolting in a 2.0 m by 2.0 m grid pattern for stope widths less than 12 m displays different results. Numerical modelling results are in line with the rock mass characterization study. It can be affirmed, as well, that no cable is carrying rock loads greater than 5 t. This fact is derived from observational behaviour of the crown pillar of an experimental stope with open stoping operations and hanging cables in the cut-and-fill stopes of the mine. An increase in the cable bolting grid spacing is, hence, recommended for implementation by mine management, based on the study described in subsequent sections. It is also suggested that the mine adopt the open stoping method, provided results of a rock mechanics instrumentation program in an experimental stope with a cable bolting grid of 2.5 m square are favourable.

Jan 1, 2007

By Bruce Conard

For many years, Bruce Conard has been engaged in reading about and discussing the desired sustainability of the mining and metals resource industry. He has, however, become concerned that there is a greater issue that requires our urgent attention: what challenges do we face as a global society? His Distinguished Lecturer presentation traces the idea of environmentally sustainable economic development but concludes that a business’ interest in its sustainability is predicated on the sustainability of our global society. Conard reviews some of the most serious challenges, including population growth, clean energy supplies, freshwater availability and climate change, and calls on scientists and engineers not only to apply their skills in helping solve these challenges, but most urgently, to speak with intelligence and passion about the need to act now.

Jan 1, 2014

By G. K. Mann

Fragmentation analysis of blast or crushed rock material is a time-consuming and costly process. During the last two decades, the mining industry has been investigating image-based analysis systems as an alternative to generate fragmentation results. Many image-based techniques and commercial products have emerged during the last few years, and the mining industry has recently begun using these tools for real-time estimation of size distributions. Some existing systems require manual image editing to add or delete edges (or net) before executing the fragmentation analysis routine. This manual procedure may take hours of time for each image analyzed. Reliable and robust image segmentation should be able to handle a wide range of rock textures and sizes under a variety of lighting conditions. This paper describes a novel software application, which has the capability to autonomously capture images and analyze them to generate the particle size distribution. The system can also process a batch of images captured during a fixed duration of time and produce the overall particle size distribution. The new method has different layers of segmentation modules, which allows the system to operate under a wide range of rock textures and lighting conditions. A new grey-level slicing technique is developed which can perform under a range of illuminating conditions. The Canny-based edge detection technique is used to segment rocks appearing in dark regions.

Jan 1, 2006

By w. w. Milde

"Since its startup in 1975, the Rabbit Lake mill has been modified (0 process both increased tonnage and higher grade ore. Ore initially came from the Rabbit Lake pit . In 1985, a major mill expansion was commissioned to allow treatment of B-zone pit ore, which is mineralogically and metallurgically different fromRabbit Lake pit ore.Mill modifications, and the changing ore characteristics and processing targets which made them necessary, are described. Mill LocationThe mill complex, shown in Figure I, comprised of milling facilities, acid plant, power generation , warehouse and administration offices, is located approximately 1.5 Ian south of the Rabbit Lake pit, and about 8 Ian southwest of the B-zone open pit mine.Original Milling CircuitOre feed to the mill commenced June 10, 1975. The mill was designed to process 1500 tonnes per day , 483 000 tonnes per year with an average grade of O.44OJo Ups and an annual production of 2000 tonnes UPs&apos; Run-of-mine ore was dumped directly onto a 60 em square opening grizzly. Oversize was broken with an Ingersoll-Rand hydrauli c rock breaker. Minus 60 cm ore was fed to a 6 m diameter by 1.8 m long Hardinge semi-autogenous (SAG) grate discharge mill. Mill discharge was screened over a Tyler double-deck vibrating screen, with screen oversize returned to the SAG mill feed chute via conveyor belt. Screen undersize (minus 2.4 mm) was pumped to 51 cm diameter Krebs cyclones in closed circuit with the SAG mill. Cyclone overflow (about 50% minus 74 micron) was thickened to 55% solids in a 30 m diameter neutral thickener .Thickened pulp was stored in two mechanically-agitated wood stave tanks (5.5 m diameter by 6 m high), to which sulphuric acid was added to obtain a pH range of 1.5 to 2.0. The fmalleaching was carried out in five more identical tanks. Sulphuric acid and sodium chlorate were used to maintain a pH of 1.5 and a terminal emf of -450 to -500 mV. Steam sparge was utilized to obtain a temperature of 45°C."

Jan 1, 1989

By V. N. Bryant

"1.0 SYNOPSISThe Colomac property, located 137 miles by air northwest of Yellowknife in Canada's NWT. will recover gold from 10,000 tons per day of open pit ore.The decision to proceed with the project was based on a mineable ore reserve of 16 million tons (including dilution) averaging 0.064 oz/ton. After an in-fill drilling program in the latter half of 1988, Colomac's mineable, proven and probable ore reserves were increased to 28 million tons averaging 0.056 oz/ton of gold.A feasibility study completed by Wright Engineers for Neptune Resources in December 1987 examined the possibility of vat leaching followed by C.l.P. and electrowinning. A second feasibility study completed by Wright in February 1988 demonstrated that a conventional agitated leach circuit using a finer grind justified the higher capital cost of this process. This study was accepted and formed the basis of the project authorization.Preliminary engineering commenced in April 1988 and detailed engineering was started in September of that year with the objective of a mine/mill start-up by early 1990.The short time period available to meet the project deadline was additionally challenging, as site access is either by plane year round, and winter road from early February to late March. Normal lead times for equipment design, specifications, quotations and bid analyses were not possible, if the winter road time-slot was to be met."

Jan 1, 1990

By Joseph N. Bakambu

It is currently recognized by mining society that autonomously guided underground mining vehicles may greatly increase the efficiency of mining production and improve human safety. Recent results in mobile robotics, data fusion and sensor development provide a solid basis for solving the problems related to autonomous underground navigation. Recently developed commercial systems mostly rely on the infrastructure that is expensive and difficult to maintain. Guideless navigation in unstructured and harsh environment of underground mines is still a challenging task. In this paper, we describe an autonomous navigation system for an underground mining vehicle equipped with on-board dead reckoning, inertial and optical sensors. This system does not require any artificial infrastructure and is capable to guide the vehicle along the complex environment of interconnected underground drifts; it also ensures the detection of obstacles on the vehicle path. The user interface for monitoring and control is described and the results of laboratory tests and on-site experiments are presented. Work in progress addresses the system integration for real equipment, and the system upgrade, adding map-building and selflocalization capabilities .

May 1, 2002

By Ken Dyck, Chuck Edwards

"Cameco's McArthur River is the world's largest high grade uranium mine. Production started in late 1999. Cameco carried out the engineering design and construction management for the McArthur River project, including all aspects of mining, ore handling and ore transportation. The ore composition was expected to vary dramatically (0 to 30% U3O8; 0 to 25% clay; etc). To cope with the composition swings, sizing screens were selected to provide classification in the grinding circuit. The grinding circuit started up close to the design to provide minus 500 micron slurry. The 50% solids (wt) ground ore slurry proved to be difficult to transport to and process at the Key Lake Mill. Slurry containing high concentrations of high density pitchblende (about spgr 8.0) and low concentration of stabilizing clays, would settle in containers. Ore transport efficiency to Key Lake was found to be unacceptable.A test classification cyclone was installed in the grinding circuit at McArthur River early in 2002. The cyclone operating parameters were not typical, but the cyclone was made to work very successfully. Transportation efficiency to Key Lake increased due to more stable slurry. Preferentially ground (fine) pitchblende particles were easier to leach at Key Lake. The radiation exposure for operators and maintenance personnel to handle the more stable slurry was also reduced.The classification sizing screens were removed from the McArthur River grinding circuit and replaced by permanent classification cyclones late in 2002.INTRODUCTIONThe McArthur River mine and Key Lake mill operations are located in northern Saskatchewan, approximately 650 and 720 kilometres from Saskatoon, respectively. Figure 1 is a location map. McArthur River is the world's largest, high-grade uranium mine, with a production capacity of 18.7 million pounds U3O8 annually. (Rosner and Edwards 1998, Dyck 2000, Jamrozek 2000, Rodgers 2001) Proven and probable reserves are more than 473 million pounds U3O8. McArthur River ore, grading on average 21% U3O8, is milled at Cameco's Key Lake operation, 80 kilometres southwest by road. McArthur River production began in December 1999."

Jan 1, 2004

By John A. Wells, Leticia Conca, Kenneth G. Thomas

"Since about 2002 there has been significant capital cost escalation, not inflation, in the mining industry causing turmoil for successful project completion. Project capital costs have more than doubled and some cases tripled in this time period. This has rendered many projects to be economically challenged and in some cases not viable. In addition higher than expected operating costs have further adversely affected project metrics such as NPV and IRR. Capital cost increases for projects have been widely reported globally. This current paper reviews three items. Firstly, why such capital increases and the various components that make up capital estimates. Secondly, it looks at reasons why preliminary estimates, for example at scoping and pre-feasibility level, have been lower than the ultimate constructed costs. Such increases and differences in estimates have caused major problems for mine builders and have led to a general nervousness on the part of those providing project finance. Thirdly, what discipline is needed in project execution in an attempt to mitigate such capital increases. The paper will hopefully give a better understanding of the various issues and factors involved for those in the mining industry.INTRODUCTION The years 2012 and 2013 were a turbulent time for the mining industry. The European economic crisis, politics, metal price volatility and a wave of changes of CEO´s in some of the major mining companies all contributed to a challenging couple of years. Two issues stood out. First, the huge increases reported in the capital costs of projects, where increases of 100% - 300% were not uncommon and in some cases exceeded that during the first decade of the 21st century. Second, company write downs related to takeovers during the boom and the stabilization/correction in commodity prices. These have led to great uncertainty, made it difficult (or impossible) to raise project financing costs, contributed to the changes at CEO level and placed many projects either on hold or cancelled altogether. It is commonplace now to read of companies talking of reduced capital expenditure and making a complete review of their projects and operations to contain costs."

Jan 1, 2014

By D. Knuutila, G. Goyette, James A. Finch, G. Bartolacci, A. Fortin, Chi Ho Lau, A. Lockhart

"In a COREM-McGill collaborative research and development project, gas dispersion parameters and froth properties were manipulated in a copper flotation plant to study interactions between the collection and the cleaning zones. In this paper, specific work on developing some relationships between operating conditions and froth stability in a rougher column flotation cell of 125 m3 is reported. Froth stability, measured by image analysis, was related to the following process conditions for specific flotation machines in an industrial case study: Gas flow rate, collector dosage, pH, frother type and dosage. Across the range examined, froth stability was improved through a decrease in gas flow rate and/or increasing frother dosage. Metallurgical results (grade and recovery) showed that both gold and copper were dependent on froth stability.INTRODUCTIONMcGill and COREM have over the past two years collaborated in a research and development project to merge gas dispersion parameters, frother analysis (McGill technology), and froth properties (COREM’s imaging system) to study the interactions between the collection zone (pulp) and the cleaning zone (froth). The main goal is to increase knowledge of flotation cell hydrodynamics since it is known to govern the metallurgical performance of the flotation process (Power et al., 2000). In this paper, specific work on developing some relationships between operating conditions and froth stability in a copper flotation circuit is reported.The objective of this work is to study gas dispersion in a large volume flotation column (hydrodynamics) and to measure its impact on the froth. By froth imaging, it is possible to diagnose operational problems on the basis of froth characteristics (Bartolacci et al., 2005a) and consequently, to propose ways of improving process performance by froth analysis (Bartolacci et al., 2005b).Another approach to froth characterization is investigated in this paper. In the same flotation column, a froth stability apparatus (column) was included (Triffet and Cillers, 2004). The mechanical froth stability apparatus is used to link “hard” froth characteristic measurements to “soft” froth characteristic measurements (those obtained by imaging)."

Jan 1, 2008