Search Documents

By Y V. Haarlem, P Coghill, N G. Cutmore, M Millen, I Carter

Due to the low concentration of gold, ore sorting for gold has always required measuring indirect properties, such as density or colour, to allow separation on a rock by rock basis. This only works on an ad hoc, by deposit basis and is likely to be least reliable where it is most required in low grade ores. One candidate technique, Gamma Activation Analysis (GAA) has been demonstrated to directly measure gold extremely accurately in powder samples of around 500gm and is used in the Chrysos PhotonAssay assay system. This method uses a linear accelerator (linac) to generate the X-ray radiation that activates the ore at low levels to emit a characteristic gold gamma ray that is then measured by a radiation detector. CSIRO is adapting this measurement technique to application on a belt at up to 800tph to measure pods of ore. The principal differences between measuring samples and an on-line measurement of pods are the requirement to measure coarse ore (<50mm), to measure a larger volume of ore as uniformly as possible, and to have an open-ended geometry with adequate shielding of the linac radiation source. These issues have all been addressed with measurements of coarse ore reported down to around 1ppm in sub-optimal test conditions. They have been demonstrated for <75mm particles with detectors capable of measuring a large volume geometry continuously. These are projected to allow measurements down to 0.3ppm in more optimum conditions for a 10 second measurement time period where the U/Th content of the ore is less than ~10ppm. Extensive Monte Carlo modelling has demonstrated that adequate shielding can be provided in relatively simple geometries with only 1 right angle transfer in the material handling. Steady progress is being made to reach the technical position required to trial an ore sorting system.

Nov 10, 2020

The task of designing stable high walls and spoil piles in strip coal mines, and stable openings with controlled roofs and floors in underground collieries - within the constraints normally imposed by economics - depends upon a reliable assessment of rock mass strengths and rock mass reactions under a variety of stress conditions. Of the geological factors influencing internal friction and cohesion within rock masses, many may be determined qualitatively or empirically from bore-hole evidence. Rock types, descriptions and properties of intact rocks, location of boundaries, limits and degrees of weathering, potential for slaking or decomposition of rocks when exposed, bedding characteristics, the nature of rock anisotropy and the likely effects of water on rock mass properties can be assessed from bore- hole data. Discontinuities, whether they be major such as faults and dykes, or minor such as joints and fractures, present a greater problem, and in most instances the mine geologist must resort to additional techniques to describe or predict their occurrence, nature, frequency, intensity or physical properties. Information on ground water and seam gas is available from bore-holes within certain levels of reliability.

Jan 1, 1977

By Cox SJD, Kramadibrata S

One of the major causes of accidents and loss of production in underground mines is falls of ground.As mines go deeper, higher stresses are encountered and strain energy stored in the rocks is more likely to be released dynamically. This results in bumping in the rock mass around a stope or development face. Such noises and increasingly difficult ground conditions are obviously a warning of more serious problems ahead. The activity is collectively referred to as rock bursting.In Australia the mining of metalliferous deposits is taking place at increasing depths at Mt Isa, Broken Hill and the Eastern Goldfields and ground control problems with rock bursts has already been experienced at all three sites.

Jan 1, 1990

By Bourke J. H, Ashcroft T. B

Many changes have occurred in the world market for manganese over the last five years. Among these, the emergence of divided steel processes for the hot metal refining of pig iron is affecting the use of both ferruginous manganese ore and ferro manganese, at this stage particularly in the Japanese steel industry. Subsequent demand for higher quality manganese materials is promoting the use of thermally beneficiated products such as sinter. In addition, many processes are being developed for the direct smelting of fine manganese ores, of which plasma technology is the most advanced. Cost pressures and product quality requirements are encouraging pre- viously self sufficient countries such as The People&apos;s Republic of China and the USSR to import high grade manganese ores to supplement indigenous lower quality supplies. At the same time, Brazil has been provided with the impetus to convert its substantial reserves of ore to value added products.

Jan 1, 1988

Supergene nickel sulphide ore mined currently by Agnew Mining Company is at times partially oxidised to sulphate. The resulting soluble nickel, and calcium and magnesium in mill water, are shown to act as depressants in flotation. The depressant effect is favourably selective in that violarite, the main nickel mineral, is less affected than pyrrhotite. Nickel recovery, however, is adversely affected, probably through reduced flotation of complex sulphides. Soda ash consumption is increased markedly by the presence of the cations as shown by operating data and pulp titration tests. A significant increase in concentrate grade, from 9% to 14% Ni, was achieved late in 1981. One of the changes in plant practice which contributed to this improvement was the addition of soda ash to mill feed rather than to flotation feed as before. It is shown by laboratory tests that this reduced the depressant effects of the cations, thereby improving recovery at the expense of rougher selectivity, or equivalently, increasing concentrate grade at constant recovery. The selective depressant effect cannot be exploited until scavenger recovery is improved and a scavenger concentrate regrind-retreat äcircuit is implemented. Development is

Jan 1, 1978

By P Krauss, S Harpalani

Methane emitted from underground coal mines, along with ventilation air and known as ventilation air methane (VAM), constitutes the largest component of coal mine methane (CMM) emissions. Atmospheric methane, on the other hand, is a potent greenhouse gas with a significant adverse impact on the atmosphere. This has led to the development of various technological alternatives for its use as an energy fuel. Techniques involving oxidation of VAM, usually consisting of very low concentrations of methane, have been validated in the past. Prominent among these technologies are the thermal and catalytic flow reversal reactors, ancillary fuel technologies, lean fuel gas turbines, and concentrators and gasifiers. However, the efficiency of any VAM utilisation technique depends on the amount and concentration of methane in the ventilation exhaust air. Therefore, quantification of VAM emission from a coal mine is the first step towards identifying the most suitable technology for its utilisation for energy production. This paper presents an evaluation of the efficacy of VAM as an energy source. It provides details of a case study aimed at developing a technique to accurately quantify VAM emission from a coal mine. It further discusses the various VAM utilisation techniques available, and presents an economic evaluation of the alternatives. Based on the findings of the study, the most feasible method for VAM utilisation is identified for the mine. The paper summarises the procedure for quantifying VAM emissions and selecting the most suitable utilisation technique.

Jan 1, 2005

German coal mining suffers from rock temperatures up to 600C which are the same as in South Africa at 3000 - 4000 m of depth. Therefore cooling plants have increased in the last decade and today a cooling power of nearly 200 MW is installed in the total Ruhr District. Cooling a mine is a little bit different from cooling a bottle of beer in a refrigerator in the kitchen because the heat taken from the bottle of beer is delivered to the kitchen some centimetres away; in mining the cooling-problem is more difficult: here the bottle of beer corresponds to the airflow at the coal face and the kitchen to the surface, So it is necessary to transport the heat or the "coldness" a long distance. In the address by Ieuan Morris some systems for transporting heat from the coalface to the evaporator of the cooling machine and further from the condenser of the machine to a return airflow were described. The following is a short idea of the way this problem is treated in Germany.

Jan 1, 1983

By Waterhouse BJ

Occurrence data of Tastubian,Sterlitamakian, and Aktastinian (all of Sakmarian Stage of Early Permian) brachiopod genera are analysed by Q-mode cluster analysis, principal component analysis, and discriminant analysis based on presence or absence of genera. Five faunal provinces and their corresponding generic associations persisted throughout the Sakmarian Stage. The additional Sasian Province incorporating the Lhasa and Shan-Thai terranes became recognisable in Sterlitarakian and strengthened in òAktastinian, implying a Tastubian-Sterlitamakian rifting event, followed by subsequent northward drift and divergence from Gondwana, and convergence with Laurasia. The nature of Permian &apos;Tethys&apos; is discussed on the basis of faunal migration and abrupt changes of faunal provinciality in Lhasa and Shan-Thai terranes.

Jan 1, 1990

By C Li, S Wang, L Qiao

Jinchuan nickel mine is the largest nickel mine in China. Cut-and-fill mining method with high density cementing materials is used in the mine. The original mining design divided the mining operation into two steps. The first step stopped the mining rooms and the second step stopped the pillars. Because the two-step method made big trouble for finally mining pillars and strongly limited the mining speed and production, it was successfully changed to a continuous cut-and-fill method without pillars. However, the mining operation in the mine has been down to 800 m and the mining condition is getting worse and more complicated. Through systemetical field investigations and 3D FEM analysis, it is proved that the mining method without pillars is feasible for mining deeper orebodies in Jinchuan nickel mine.

Jan 1, 2000

By K L. Silversides

Shales form distinctive peaks in natural gamma downhole logs, which are used to manually identify the location of ore boundaries. These shales form important lithology markers that can potentially be automatically identified using Gaussian processes. This approach is trialled using data from a typical iron ore mine in Western Australia which contains the Marra Mamba sequence of the Hamersley province.The method uses Gaussian processes (GPs) with a single length scale squared exponential covariance function. A library of 8 m sections, where natural gamma measurements were taken at 10 cm intervals down the hole, was used to train the GP model. This library was iteratively improved and was tested using natural gamma logs that were not included in the library. Areas that were misclassified or were not clearly classifi ed were added to the library. The new library was then used to train the model and improve the results. The trials used a double gamma peak from the NS3 and NS4 shales at the boundary between the Newman 1 and Newman 2 ore zonesin the Newman member and the AS1 and AS2 shales at the base of the West Angelas member. The results show that both boundaries can be identifi ed with an accuracy of over 99 per cent. The classification has the highest accuracy on undeformed shales. This method provides a fast, accurate and objective identifi cation of shale and ore boundaries and can potentially replace the current manual detection.

Jul 11, 2011

By Mike Sharwood

This subject is to be discussed in greater depth by Mike Sharwood. It has also been the subject of a mini-symposium by the Melbourne Branch of the AusIMM in October, 1993. The papers from this symposium were distributed to the membership late last year "to raise their consciousness and to promote greater awareness and understanding of the wide range of liabilities that may arise". An introductory paper by Nicholson outlined the many areas in which liability may arise with particular emphasis on expert reports, eg: Takeovers Schemes of arrangement Acquisitions from associates Prospectuses Related party transactions Directors&apos; duties Continuous disclosure Other influences (environmental, occupational health and safety, trade practices)

Jan 1, 1994

The Mount Sisa orebody on Misima Island, P.N.G., consists of goldsilver mineralisation associated with massive carbonate and amorphous iron-manganese oxides in fractures and breccia matrix. The orebody forms the northern extension of the Umuna deposit, which lies within a three kilometre strike length of a northwest trending, 300 metres wide, high angle fault zone. The structure is deeply oxidised, with the magniferous oxide material resulting from oxidation of carbonate. The wallrocks are metamorphosed basement psammopelites and basic volcanic rocks, extensively intruded by microgranodiorite. These are dominantly epidotised and sericitised. The precious metals are associated with anomalous Cu, Zn, Pb, Mn, As, Ba, Ga, Sb, and Mo. Many of the features of the Mount Sisa mineralisation are characteristic of volcanic-hosted epithermal deposits of western North America.Lithologic and textural gradation is observed between the carbonate hydrothermal breccia-fill at Mount Sisa, and the quartz dominated brecciafill and dilational fracture-fill mineralisation which forms most of the Umuna deposit to the south. This gradational relationship is analogous to that in the Amethyst-OH vein system at Creede, Colorado, where it is shown to be indicative of deposition from laterally migrating fluids.

Jan 1, 1988

By K Orth

The volcanic successions that host massive sulphide deposits are diverse in composition, facies types and facies relationships. They also show a variety of spatial and temporal relationships to mineralisation. In many examples, such as the Koongie Park Formation in Western Australia, the host succession includes more or less conformable syn-volcanic sills with peperitic contacts. Such sills can be an important source of heat for fluid circulation, influencing patterns of hydrothermal alteration and the location of co-eval and later mineralisation. The impact of syn-volcanic sills on the host succession depends in part on the initial porosity and permeability of the enclosing facies. The special properties of glassy pumice û being highly porous, permeable, and reactive û allow pumice-rich facies to preferentially focus hydrothermal fluid flow. However, the same properties promote early alteration and porosity reduction. Hence, the diagenetic and compaction history of pumiceous facies strongly influences their potential to host massive sulphide mineralisation. In contrast to pumice, dense glass has relatively low porosity, at least initially, and does not compact. Non-vesicular glass is a major component of submarine lavas, syn-volcanic intrusions and some volcaniclastic facies. However, especially in submarine settings, dense glass is commonly intensely perlitically fractured soon after eruption. The fractures greatly increase the porosity and permeability, locally accelerating diagenetic and hydrothermal alteration. In addition to false pyroclastic textures, altered perlite may exhibit false porphyritic textures. Silica- or feldspar-altered perlite kernels surrounded by intensely altered phyllosilicate domains can resemble phenocrysts in a fine grained groundmass.

Jan 1, 1999

By Kubo H, Kubita K, Morinara M

A quantitative method for predicting the mechanical properties of zinc alloys is proposed on the basis of the molecular orbital calculation of electronic structures. A new parameter which is the s-orbital energy level, Mk , of alloying elements in zinc was introduced into this method. This Mk parameter correlates with the electronegativity and the atomic radius of elements. The compositional average of this parameter varied linearly with the tensile strength and the hardness of commercial alloys and some alloys developed by Mitsui. This electronic method was very convenient in designing high performance zinc alloys efficiently.

Jan 1, 1993

By Bhattacherjee A, Makesh S

Mechanised sub-level stoping is one of the most widely accepted stoping practices followed in base metal mines in India. As a general practice, blast-scheduling of rings in these stopes is done either heuristically or randomly which leads to a high fluctuation in ore grade when drawn and delivered to the mill. In this paper, dynamic programming has been investigated as an optimisation technique for optimal blast-scheduling of rings. A microcomputer based dynamic programming algorithm has been developed in C language which runs under the UNIX environment. A case study based on Indian mine data is presented to demonstrate the application of the dynamic programming concept and use of the developed software. It is concluded that dynamic programming can be used as a production planning tool in Indian mines practicing sub-level stoping and following heuristic/random approaches for blast-scheduling of rings.

Jan 1, 1995

The earliest caveman, very much a minority group, in the face of great adversity and person- al peril, had to take his livelihood by stealth or force of arms - aided by some degree of reas- on and ingenuity. He was pretty much a law unto himself. As time went on, his type became more numerous; and, after bumping heads with the- tough bloke who lived in the cave across the valley, he decided that perhaps he ought to try to get along with him. Perhaps he could trade some over-ripe emu meat for that `roo skin that he had tried to take. Then too, next time he wants a woman, he had better use a lighter club and just stun her a little - that last one was pretty badly bashed. Perhaps he should keep her around the cave and train her to keep the fire going, gather some roots, and skin the game. Those joeys of hers are kind of cute too. Of course they eat, and it would necessitate bringing in more food. So man gained increasing responsib- ilities to his family and neighbours. He domesticated animals, learned that he could cultivate certain plants that were palat- able and would supplement the meat diet, and found that he could modify earth materials to make tools - he became a grazier, a farmer, a miner and a manufacturer. He ceased to be nom- adic and community life came into being. This complicated life and made more rules essential.

Jan 1, 1974

By Kubo H, Ninomiya R, Ojiro T, Sato T

New high-strength Zn alloys for moulds are demanded from the automobile and electric industries in Japan, because the s rength of Zn moulds is still not high enough for the mass production. There are two approaches to improve the strength of Zn alloys. One is to increase the Al content. ZA alloys (ZA-8, ZA-12, ZA-27) were developed through this approach. The other is to increase the Cu content. But it is known that an increase in Cu generally depresses the castability of Zn alloys, so that the alloys with increased Cu have been rarely studied until now. In this study a reconciliation between the strengthening and the castability of Zn alloys by enriching both with Al and Cu has been attempted. Accordingly we have studied on the Zn alloys containing 4 to 25 mass per cent Al and to 24 mass per cent Cu have been studied. Their fluidity, which primarily corresponds to the castability of the alloy, were measured first and 19 alloys were selected based upon their fluidities and casting temperatures. Mainly the mechanical properties of all 19 alloys were tested and some were found to be excellent in both strength and castability. Z1009 (Zn-IOAI-9Cu-0.02Mg alloy) cast in a sand mould has the tensile strength of 360 MPa while ZAS (Zn-4AI-3Cu-0.04Mg alloy), which is the most popular alloy for moulds, is 215 MPa. Z2520 (Zn-25AI-20Cu-0.02Mg alloy) cast in a sand mould has a Vickers hardness of 178, compared to 107 for ZAS and 104 for ZA-27 (Zn-27AI-2Cu-0.02Mg). Furthermore the castability of Z1009 is as good as that of ZAS. The underside shrinkage occuring in casting ZA-27 is restrained in Z2520.

Jan 1, 1993

By J Ortiz

In almost all copper mining companies, mine planning is done considering different time frames, leading to long-term (life-of-mine) (LOM), medium-term (first three years) and short-term (first year, monthly, weekly, and up to daily plans). Shorter term plans are usually associated with more abundant information, hence models with lower uncertainty. However, they capture more of the variability found on the geological attributes. In long-term models, usually estimation methods tend to hide this variability, providing smoothed interpretations.Medium and long-term plans consider average values for the parameters and optimisation techniques are applied aimed at maximising the economic profit. Short-term plans, on the other hand, are made to comply with the medium-term promises, maximising the use of the available resources (equipment and processing capacities) and dealing with the variability not characterised in the previous planning stages. This generates an important gap between the short-term and the medium and long-term plans. A case study was made using an important oxide copper mine, where the variability found in the short-term plan has a large impact in the productive process, thus reducing the daily ore grade variability is an important goal. In this paper, this planning issue is addressed by creating medium-term mine plans using mixed integer programming which are compared using the output of a simulation of the daily extraction that is aimed at satisfying the daily constraints of the processing plant, the availability of mining equipment and the variability of ore grade. The result shows the expected gap between these mine planning processes, which suggests correcting some of the parameters used in future medium and long-term plans.

Sep 26, 2011

By Langham B. M

A chemical study of the petrographic components of Greta (Maitland) coal, carried out by the Metropolitan Gas Co. (Melbourne), has revealed an anomaly in the composition of the durain which was thought to warrant petrological investigation.The original study, by the Metropolitan Gas Co., extended over eight shipments of coal received during the winter of 1943.The percentages of the several petrographic components were eslimated by careful handpicking of large samples of each shipment, and analyses were made of the handpicked components, which were also tested as to their gas-making and coking properties.The results are summarised in Tables 1 and 2. At first sight the components of the Greta coal bear a general resemblance in composition to those of other bituminous coals of similar rank, apart from a notable richness in volatiles, which is a distinctive feature of Greta coal. The durain has a typically higher ash content, and lower volatile content than the clarain (Table 1); and the coking behaviour of the four components is typical (Fig. 4).When, however, the analyses of Table 1 are re-calculated on a dry, ash-free basis, an anomaly appears: the clarain and the durain, on this &apos;pure coal&apos; basis, have practically identical compositions, with the durain containing a slightly higher proportion of volatiles than the clarain (cf. Table 3); but the tar yield of these two components is very different (Table 1). Re-calculated on a dry, ash-free basis, the yield from the clarain is 18.9 gallons of tar per ton, while, that of the durain is 29.0 gallons per ton. The gas derived from the durain is correspondingly richer in illuminants (CH etc) and poorer in hydrogen than that from the clarain (Table 2), and is also notably richer in nitrogen.That the composition of the Greta durain is consistent is proved by the analyses of Table 3, in which the compositions of the respective durains and clarains of eight separate shipments of coal are compared. In most bituminous coals, the durain contains several per cent less volatile matter than the associated clarain, and high volatile content in a durain usually indicates a durain rich in spores.

Jan 1, 1947

A brief review of the problems in ventilating and cooling deep and hot Australian mines is presented. An overview is given on the development of the controlled partial recirculation concept. The main part of this paper describes the first majo

Jan 1, 1994