Search Documents

The coalmining industry in most countries has, at various times, suddenly been confronted with a decrease in demand for coal. Readjustments made to reduce productive capacity to match the reduced demand for coal have often resulted in hardship to mineworkers, loss of capital investment to mineowners and loss of coal reserves. The consequences of the methods of readjustment adopted in the past have contributed to the low esteem in which coalmining has come to be regarded by a large section of the gel).eral public in many countries.Four sections of the coalmining industry, representing different periods of time, different countries, and different methods of industrial organisation have been examined:Great Britain and the U.S.A. during the inter war years, the post war European Coal and Steel Community, and post war Great Britain under the National Coal Board. An assessment has been made of the methods adopted in each case to reduce productive capacity to match a reduced demand for coal. Finally the fundamentals of the problem-as it affects the coalmining industry of any country-are considered, and possible solutions put forward.During the 1950's, surplus productive capacity was a problem in many coalmining countries, including Australia and New Zealand. As a rule no techniques are developed beforehand to solve problems introduced by a sudden decrease in demand for coal. The situation is usually tackled by a series of short term decisions based on expediency, which often in the long run only aggravate the problem.

Jan 1, 1961

Hot briquetting is a reliable, fully developed industrial concept for the passivation of direct reduced iron produced with the various processes of direct reduction. During hot briquetting, the large specific surface area of direct reduced iron is drastically reduced, and therefore the well-known problems caused by reoxidation and overheating are avoided. Even the shipping instructions published by the International Maritime Organisation (IMO) confirm that Hot Briquetted Iron (HBI) can be handled and shipped without special precautions. From the mid-1970s until today, after extensive pilot testing of the technology, a number of industrial plants for the hot briquetting of direct reduced iron have gone into operation. Additional hot briquetting plants for already established but also for new direct reduction processes are tinder construction or in different stages of planning. This paper describes the characteristics of HBI and its current industrial application for various Direct Reduction Processes.

Jan 1, 1999

By C Ross

This paper uses the results of research trials by Landcare Research and Forest Research Institute and assessments of reclamation plantings at mines and other drastically disturbed sites to describe methods of enhancing restoration of native forests. The characteristics of mine and forest environments are compared to highlight the difficulties facing restoration and techniques which result in successful restoration are described. Selection of the most appropriate technique is illustrated by describing restoration of lowland beech-podocarp forest at a West Coast coal mine. The key to successful reclamation is to understand the factors controlling and limiting plant establishment and growth, then to design rooting media, surfaces and management regimes to create a favourable environment. This paper concludes with a summary of the planning and technical factors which are critical for successful restoration of native forest.

Jan 1, 1995

CONTENTS.IntroductionAcknowledgementsDescription of MineVentilation of MineOrganisation of Fire Fighting SquadsTraining of Fire Fighting SquadsRescue WorkFire Fighting and Rescue EquipmentFire AlarmsConclusionINTRODUCTION.This paper should be read in conjunction with that by R. P. Hooper, entitled "Underground Mine Fire Prevention at the South Mine," Broken Hill. Contents of the paper have been arranged similarly for easy reference. The methods used in educating employees in the use of Proto apparatus remain basically the same, but many changes in the methods and equipment used in subjugating fires have been brought about by the practical experiences gained by officers of the company in extinguishing the outbreaks which occurred in the latter half of 1944.Three fires took place during this period, the first in July, on M.L. 11 in openings leading to timbered workings previously worked and subsequently abandoned by...

Jan 1, 1946

The Tasman Orogenic Zone is regarded as a single metallogenic province (the Tasman Province) with four SUb-provinces corresponding with its major tectonic components: the Lachlan, New England, Hodgkinson.and North Queensland orogenic provinces. Within the Tasman Province there are four main ore-rock associations.These are1. manganese and iron with sedimentary and basic volcanic rocks,2. zinc-lead-copper and copper with intermediate-acid volcanic sequences,3. minor chromium, platinum, and osmiridium with ultramafic complexes, and4. tin, wolfram, gold, and copper with syn- and posttectonic granitic intrusions.Whereas the ores of ultramafic and volcanic associations form geographically-restricted metallogenic districts, the ubiquitous granitic ores may be subdivided into twenty-one districts that cover almost the entireOrogenic Zone. The Tasman Province is notably lacking in uranium ores and Mississippi Valley-type deposits.There is a distinct tendency for ores of each association to be progressively younger to the east and north, thus paralleling the progressive growth and stabilization of the Zone. Similar ore-rock associations are present in repeated phases of mineralization from the Cambrian to the Permian-Triassic, reflecting the essential homogeneity of the Tasman Province, and the similarity of the successive tectonic cycles.

Jan 1, 1972

THE Australian States and New Zealand have for many years provided instruction in mining, metallurgy, geology, and their allied subjects through their Universities and Schools of Mines. Though such education has been provided at considerable expenditure, there is no legal recognition whatever given to the holders of degrees, diplomas, or certificates granted by the authorities controlling these educational institutions. Certain of the, Australian States and New Zealand require, however, that mine managers and other officials employed by the mining industry shall 'hold' certificates granted by their respective Mines Departments.The position at present is that each educational institution is practically a law unto itself, and therefore in many ways there is a want of uniformity amongst institutions all aiming at the same result the training of mining men. The object of this paper is, in the first place, to point out certain aspects of this want of uniformity, and thereby how disabilities accrue. Some points in connection with the granting of State certificates will also be...

Jan 1, 1915

By M J. Begbie, P C. Keall, M P. Simpson

The Golden Cross low sulfidation epithermal deposit occurs in pervasively altered andesite of the Waipupu Formation and in the Waiharakeke Dacite. The unaltered, post-mineral Whakamoehau Andesite overlies these units. The Empire zone of the Golden Cross deposit contains a stockwork which is currently mined by open pit methods, and a series of veins that are mined underground. Alteration envelops both the underground and open pit mineralisation. The core of the alteration zone contains silicification, as quartz veins, and adularia. Shallow portions of the system contain illite-smectite and a thermally unstable chlorite, tentatively identified as corrensite, which pass downward into illite and chlorite, respectively. Replacement calcite occurs widely throughout the altered zone; pyrite is nearly ubiquitous. This alteration assemblage indicates formation from near-neutral alkali chloride waters. A late, post-mineralisation alteration assemblage of calcite, smectite, illitesmectite, kaolinite and siderite presumably formed from weakly acidic, steam-heated CO2-rich waters.   We have identified eight stages of vein formation: (1) sulfide veins, (2) black veins, (3) massive veins, (4) banded veins, (5) thin white veins, (6) crumbly veins, (7) massive/platy calcite veins, and (8) flattened rhomb calcite veins. Gold mineralisation occurred relatively early in the lifetime of the system, dominantly during 2 through 4. The late calcite veins (7 and 8) and early sulfide veins (1) are barren.  

Jan 1, 1997

The Fraser Range is composed dominantly of basic pyroxene granulites derived from basalts, many of which appear to have been vesicular and pillowed. Acidic and basic garnet-bearing granulites are important in the west, and acidic granulites and narrow anorthosite layers are dominant in some regions east of the Fraser Range. An extensive flat-lying olivine gabbro sheet cuts the granulites, and in places has been converted to spineI-bearingmeta-gabbros and pyroxene granulites. The granulites of the Fraser Range (Proterozoic) are separated from the gneisses and schists of the goldfields regions (Archaean) by the Fraser Fault, over which there is a large gravity anomaly (gradient 20 milligals per mile). Some of the problems associated with the concentration of Cu, and Ni liberated from mineral lattices during metamorphism, and other principles of metal concentration in granulite terranes, are discussed. The recognition of vesicular and pillowed zones, even though highly metamorphosed, is of fundamental importance.

Jan 1, 1969

By G F. Brent, R D. Hart, C Carr, F Felipe

In underground operations, where copper, gold and other metals are mined, the open stopes can be backfilled to stabilise surrounding workings. This fill may consist of tailings from the processing plant, usually mixed in slurry with a binder such as ordinary Portland cement (OPC). Extensive use is made of tailings in OPC-based paste fill, cemented hydraulic fill or cemented aggregate fill applications. A large underground operation such as the Mount Isa Copper Operations utilises over three million tonnes of backfill per annum. Geopolymers offer an alternative binder system with significant environmental advantages over OPC. Geopolymers are formed by polymerisation of aluminosilicate precursors in an alkali medium. They generally form products with superior strength characteristics as well as increased resistance to degradation, particularly under acidic conditions. Geopolymers have lower carbon dioxide emissions associated with their manufacture than OPC and offer further potential advantages, such as the use of less water and more waste materials. The application of geopolymers to weak material systems such as mine backfill has not been widely studied. The aims of this investigation were to assess a range of Australian mine process wastes for suitability as feedstocks in fill applications and to construct a range of these cemented minefills using a geopolymer binder. The physicochemical characteristics of each of the wastes are discussed as well as how they ultimately contribute to the geopolymer cement through direct replacement of OPC. Results from various tests on the candidate geopolymer fill formulations are presented and the potential of such fill formulations to replace OPC in mine backfilling operations is highlighted. The significant potential contribution to reducing greenhouse gas emissions from the use of geopolymer-based mine backfill across the industry is noted. Conversion of a single mine, such as the Mount Isa Copper Operations, is shown to match the reductions in greenhouse gas emissions due to the current total installed photovoltaic electricity generation capacity of Australia. A similar examination of wastes available to a gold mine could potentially yield new binders for use in established or new fill systems.

Jan 1, 2007

High Pressure Grinding Rolls Scale-Up and Experiences

Sep 13, 2010

IN this paper an attempt is made to describe the sluicing operations on the tin fields of north-eastern Tasmania. No claim is made to completeness, for much of the ground has already been covered, and nothing is to be gained by needless repetition. On this account some portions of the subject have obviously received but attention in order that others may be rather more fully dealt with; for instance, referring to the accuracy of various methods of valuing alluvial deposits, particulars of efficiencies, and water duties on both overburden and drift; also, the system of recording water distribution, &c. The plans of the tin-streaming shed, sluice and feed race, and overburden tail-race represent types of the most modern design.GEOLOGY. The principal alluvial dcposits being worked at the present time are situated either in the ancient or modern bed of the Ringarooma River or its tributaries. This river flowed in a north-easterly direction, receiving numerous tributaries on either bank...

Jan 1, 1910

By S Maritsa, E K. Chiwandika, S M. Masuka

The iron and steel industry is experiencing an increase in the use of iron and steel commodities within societies, decarbonisation pressures, depletion of high iron ore grades and high energy consumption. This necessitates scrap metal recycling, low-grade ore utilisation using the induction or electric arc furnace to achieve the global target of net zero CO2 emission. The available highquality scrap metal cannot sustain the steel industry but the world has unused hematite-goethite ores. It is the aim of this research that this resource be utilised using the induction furnace to sustain the steel industry in an environmentally friendly manner. Indurated pellets prepared from the hematite-goethite ore, 5 wt per cent limestone and 5 wt per cent coal addition were smelted in the induction furnace at 1350 ± 50°C with 25 mins holding time. The effects of basicity and carbon content were also investigated to optimise the smelting parameters. The results showed that the careful control of the basicity, and iron-to-carbon ratio maximised total metal recovery. The optimal basicity ratio was determined to be 1.3 and a carbon to iron ratio of 1.4 achieved a total metal recovery of 73 per cent. The metal recovery was closely related to the estimated slag melting temperature. The basicity ratio of 1.3 achieved the lowest slag melting temperature estimated to be around 1380°C based on the CaO-SiO2-Al2O3 phase diagram. The recovered metal had a comparable chemical composition and microstructure to that products from an ITmk3 furnace.

Jun 19, 2024

The mineral matter has been isolated from a selection of Australian bituminous coals using low temperature (radio-frequency) oxidation or hydrogen peroxidation techniques and the species present identified by x-raydiffraction. Quartz, kaolinite, and a range of mixed layer clay minerals are the dominant constituents of the coals studied, with carbonate, sulphate, and phosphate minerals abundant in some samples. The clay bands thatoccur within these coal seams contain similar mineral assemblages to the coals themselves, but the lutites that form the inter-seam strata have a markedly different mineralogy, characterized by abundant quartz andillite and a low kaolinite content.The kaolinite is thought to have formed chiefly by interaction of silica and alumina in the waters of the coal swamp, aided by the catalytic action of organic acids, while most of the other clay minerals are probablydetrital. The absence of illite from Australian coals is not fully understood, but it may reflect the action of organic acids on the detritus in the swamp, coupled with deposition in freshwater rather thanmarine conditions. Pyrite, although present in some coal samples when fresh, may undergo oxidation during storage to form a number of sulphate minerals, some of which may interact with any calcite present toform gypsum.The mineral matter assemblage in the coal determines to a great extent the fusion characteristics of the ash.Unless abundant carbonates are present, coals with kaolinite-rich assemblages have a very refractory ash, while those rich in chlorite or montmorillonite have ash fusion temperatures between 1000 and 1300°C. Theinfluence of the minerals on coal preparation and coking properties is also brieflY discussed, as well as the potential of mineral matter studies in coal seam correlation.

Jan 1, 1978

By P Illig, R Newberry

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Recent exploration efforts in Eastern Interior, Alaska have discovered significant ca 72 Ma Au-Cu-Ag sulfide-amphibole skarn mineralisation within metamorphic rocks of the Yukon Tanana Terrane, 20 km SE of Tok, Alaska. Contango ORE, Inc’s 1.1 Moz Au-equivalent Peak deposit skarn discovery is hosted by an argillaceous marble layer in quartzite and micaceous quartz schist. This skarn mineralisation is both younger and much more Cu-rich than the typical ca 90 Ma Au intrusive-related gold deposits in the Tintina Gold Belt (eg Ft Knox and Pogo). Silicates at the Peak skarn are predominantly high Cl-, randomly oriented, Fe-rich amphibole, lesser chlorite and minor (<1 per cent) residual clinopyroxene (Hd80–90). Amphibole is ferroedenite to hastingsite and contains up to 4.2 wt per cent Cl-. Pb-Zn-Sb veins are most distal and cut schist wall rocks and amphibole skarn. The predominant sulfide mineral is pyrrhotite, with subordinate arsenopyrite and lesser chalcopyrite, native gold, minor pyrargyrite (Ag3SbS3), trace Jonassonite (AuBi5S4) and maldonite (Au2Bi). Native bismuth, galena, hedlyite (Bi7Te3) and Joseite-A (Bi4TeS2) are also present.Unmineralised garnet (Ad38–43) + pyroxene (Hd60–63) and pyroxene-rich (Hd76–80) skarn occurs in different fault blocks from the Peak skarn and represent proximal skarn related to different intrusive centres. Amphibolites in the region are true metabasites, display metamorphic fabrics and lack the high Fe-Cl compositions of the amphiboles in mineralised skarn. Residual clinopyroxene in the Peak skarn is rare, and most of the hornblende is coarse radial splays that shows no evidence for replacement of pyroxene. Consequently, we propose that the sulfides and hornblende were mostly direct replacements of argillaceous marble and not formed by retrograde alteration of pyroxene-rich skarn. The high-Cl amphiboles indicate that the fluids were Cl-rich and presumably carried Cu via Cl complexing, unlike the Cl-poor fluids associated with ca 90 Ma Cu-poor deposits of the region.CITATION:Illig, P and Newberry, R, 2015. Amphibole Au-Cu skarn and massive sulfide replacement at the Peak deposit, Eastern Interior, Alaska, Peru , in Proceedings PACRIM 2015 Congress, pp 415–422 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

A composite iron ore-reductant pellet is a mixture of fine iron ore and fines of coal/char/coke, bonded at essentially room temperature with sufficient green strength for subsequent handling. In ironmaking, these pellets offer the advantage of fast reduction, utilisation of fines, non-coking coal and coke breeze. The composite pellet-based alternative ironmaking processes constitute a promising route for ironmaking in future. The present paper is a brief review of kinetics and mechanism of reduction of iron oxides into iron and other associated reactions, when these pellets are heated to high temperature. It would draw significantly from investigations conducted by the author and his co-workers.

Jan 1, 1999

The point of the anode effect on carbon anodes of dcfincd surface area. during electrolytic decomposition of alumina dissolved in molten fluorides. has been determined from current-voltage curves. The reproducibility and accuracy was found to be better for cell voltage than anode current density. Results have been obtained for the effect of alumina concentration temperature and carbon type. The point of the anode effect was strongly dependent on both the alumina concentration and the carbon type. For high alumina concentrations it has been found that the anode effect approaches reversibility. From these results it is concluded that co-evolution of CO, and CF. occurs prior to the onset of the anode effect. The anode effect results when the CF, content becomes sufficiently high for the melt not to wet the electrode surface and is maintained because of the slow desorption of CF, and the high electrode potential that results.

Jan 1, 1967

How the Australasian and Canadian Codes (VALMIN and CIMVal) approach mineral property valuation is described. Brief comment is also made on the International Valuation Standards CommitteeÆs interest in a global valuation standard for Mineral (Extractive) Industries and the South African SAMREC initiatives to adopt a VALMIN-like Code. The conventional tripartite classification of valuation approaches into those that are Market-based, Income-based and Cost-based is outlined. It is best practice to use as many of these approaches as possible (and as many methods as reasonable in the particular circumstances), given the quantity and quality of the data available on the Mineral Asset (which depends upon the state of development of the mineral property). The use of specific methods must satisfy the basic considerations of logic and reasonableness and the purpose of the valuation. The competence, judgement and repute of the valuer are critical factors, since all valuations are time and circumstance specific. What constitutes æMarket ValueÆ in the different jurisdictions is discussed and definitions are given. Challenges facing the globalisation of a VALMIN-type Code for the international Minerals Industry are the influence of real estate valuers and the US jurisdictional idiosyncrasies. This is mainly due to a fixation on real property rights with a preference for using real estate-like comparative sales techniques (Market Approach) to the exclusion of Income-based approaches; a regulatory reluctance in the US to accept that Resources have considerable value; and the International Accounting Standards BoardÆs preference for Historical, rather than Current Value, accounting.

Jan 1, 2002

By Ray H. S, Galgali R. K

It is well accepted that the blast furnace will continue as the main route for iron-making for many more years. However, its limitations have motivated researchers to look for alternative routes, particularly, those where non-coking coal is used for liquid iron production. Smelting reduction (SR), where coal and oxygen are used to produce liquid iron and power is now receiving serious attention. Several smelting reduction reactors are now operating in pilot plant scale and one or two have reached commercial status.

Jan 1, 1999

By L Avalos, F Melo Miranda, J Misle, M Ingwersen

"Los Pelambres, majority owned by the Chilean company Antofagasta Minerals, is one of the leading producers of copper and molybdenum in the country. It is located high in Andes Mountains, over 3000 metres above sea level, 316 km from the nation's capital, Santiago.The maintenance service supplied to Los Pelambres over the past 13 years has evolved to the point that FLSmidth now provides an integrated service crucial to the management of their customer's assets. The contract initially involved specialty mechanical, electrical and instrumentation maintenance and has developed to encompass maintenance planning and plant control systems.The integrated partnership has delivered excellent results in the areas of improved availability, reliability and return on investment. The operation is now amongst the industry leaders in plant availability.The integrated maintenance service has delivered: An increase in plant availability from 93%, in the first year, to 96.5% today, generating approximately $50 million additional income per year, Quality work procedures, Process and equipment improvements, Major shutdown planning involving more than 700 personnel, 6000 parts and over 2 000 discrete activities.The ongoing success of the partnership requires a high level of understanding between both companies. A commitment to maintain a long term sustainable relationship, based on a ""win - win"" culture, is the key to this success. In this regard Los Pelambres has been a pioneer in establishing and developing such relationships.This case study will share the lessons learnt, the measures taken to improve performance and the best practices adopted during the 13 year evolution of the maintenance service partnership.CITATION:Misle, J, Melo Miranda, F, Avalos, L and Ingwersen, M, 2013. Integrated maintenance services at the Los Pelambres Mine in Chile - The lessons learnt and best practices developed from a long-term sustainable relationship, in Proceedings MetPlant 2013 , pp 296-331 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

A detailed study of the capital investment and production cost for copper electrowinning plants shows that significant savings in both can be achieved by increasing the current density. From the economic analysis it is determined that the optimum current density which will result in lowest capital investment and lowest operating cost is between 60 A/sq. ft. and 70 A/sq. ft., or at least three times as high as the Conventionally employed current density. The specific investment, expressed as $/ton-year, is found to be a function of both the current density and plant capacity and has a minimum value at the optimum current density. Empirical equations are developed for the purpose of estimating the capital investment and operating cost for plants of any production capacity operating at any current density.

Jan 1, 1972