Search Documents

By Kavetsy A

In surface mining operations, the ease with which a muckpile may be dug is a dominant factor in mining efficiency. Within broad limits this is largely independent of the fragment size dis- tribution, since the equipment used to move the broken rock is generally larger than in underground mines. In such cases, muck- pile shape and voids ratio within a muckpile heavily influence mine productivity. In a particular operation, the muckpile shape after blasting should be tailored to the digging equipment being used. A front- end loader is best suited to a low, flat-lying, loose muckpile, because of its fairly good mobility and small break-out force with its bucket. In contrast, a rope shovel lacks mobility, generates a much larger break-out force with its bucket, and fills its bucket in a vertical filling motion. Therefore, it is ideally suited to well fragmented, steep faces. In situations where a dragline is used, the requirement for a suitable muckpile depends on the operat- ing scheme of the dragline. For a conventional highwall key method the preferred work- ing level of the dragline is the same as the highwall, so that the dragline may sit over its key. In this situation, the ideal muck- pile shape involves relatively little displacement of the fragmented rock, with a minimal "power trough" at the back of the blast. In throw blasting, on the other hand, it is desirable to cast as much of the spoil as possible across the pit. It is then necessary to optimize the blast design by maximizing the throw percentage under any necessary constraints (e.g. damage, vibration, flyrock, explosive cost).

Jan 1, 1988

By Cutmore NG

The moisture content of iron ore is important in handling, stockpiling, transport and further processing operations. Typically these ores contain both `free' and `bound' moisture, the latter being moisture that is not removed in a conventional laboratory determination of moisture by air drying at 105¦C, and it is the free moisture that is important in dust control and ore handling. The CSIRO Division of Mineral and Process Engineering has previously developed and commercialised gauges, based on capacitance and microwave techniques, for the on-belt determination of moisture in coal and minerals. However, these gauges determine total moisture, and have a different sensitivity to free and bound moisture in the material analysed. Consequently, the accuracy of determining total or free moisture alone may be significantly affected by variations in the bound moisture content. An investigation has been carried out on the simultaneous determination of free and bound moisture in iron ore fines (

Jan 1, 1993

By Haeussler P, Christie A, Bradley D, Skinner D

Mesothermal gold deposits of southern Alaska and Westland, New Zealand have both formed at the seaward edge of major collisional zones in the Pacific basin. In Alaska, production of large fluid volumes correlates in time with the addition of heat into the lower parts of the accreted terranes in the late stages of collisional orogeny. This heat was critical for driving both the metamorphic reactions that released the large volumes of fluid that carried the gold, and the contemporaneous widespread anatexis and magmatism. In Alaska's Chugach terrane, this heat was produced by subduction of a spreading ridge beneath the North America continental margin in the Eocene. The resulting products were the S-type granites and gold-bearing veins. The similar widespread S-type plutonism and gold veining in Westland's Buller terrane suggest that a similar tectonic event could have triggered ore formation along the southeastern edge of Gondwanaland. Based on the Alaskan model, a Devonian or Early Carboniferous age is favoured for high volume metamorphogenic fluid generation and gold vein formation in Westland.

Jan 1, 1995

This paper presents an overview of the strategy adopted to bring the Ballymoney opencut lignite deposit to an advanced stage of mine design and confidence. Certain aspects of the project differentiate it from the normal Australian experience. These include the thick overlying glacial drift, the proximity to established infrastructure and the wide fluctua- tions in annual lignite demand. The incorporation of these factors in the mine plan are discussed. The deposit area is located near the town of Ballymoney, in Northern Ireland. In July 1986, after winning an internationally competitive tender, Meekatharra Minerals Ltd commenced an exploration programme designed to delineate reserves to supply a 450 MW power station. In less than eighteen months, a complete evaluation was undertaken and a price submitted in December 1987 to the relevant authorities for the supply of lignite. Subsequently, UK government consultants and significant inter- national banks have endorsed the findings. The mining study commenced with the evaluation of various develop- ment strategies, followed by selection of the most viable mining method and equipment. The equipment selected will mine four million tonnes of lignite and eleven million cubic metres of waste each year. In year 15, the waste removal requirement increases to almost seventeen million cubic metres. This results in an average strip ratio over the mine life of three cubic metres of waste per tonne of lignite. The quality of the product delivered to the run of mine conveyor transfer point, based on maximum resource recovery, will include heat content of 8813 kJ/kg (3789 Btu/Ib), ash content of 28% and moisture content of 40%.

Jan 1, 1989

Pyrrhotite is pyrophoric when in a finely divided form. The problems of disposing of large quantities of finely divided pyrrhotite separated out by metallurgical processing from ore are formidable. In the case of an underground mine, a solution to the problem of disposal is to place the pyrrhotite in the stoped out areas and seal from any air supply. Further, the pyrrhotite could be diluted with tailings which would reduce the possibility of combust- ion. Several enquiries to various centres and authorities have shown that the products of the slow oxidation of pyrrhotite with moisture present can cement an inert matrix into a stable fill similar in physical prop- erties to fill stabilised with Portland cement. Stabilised fill can be used to advan tage with a suitable mining method to provide high recovery. The investigation demonstrated that air and 15% w/w water must be present for the fill to harden and that the sizing of the particles is a critical factor in drainage of a hydraul- ically placed fill and subsequent even harden- ing of the fill in a stope. With the materials used in the experiments in which the - 51 micron component of the tailings had been dis- carded, an optimum mix was found to contain 4:1 tailings/slag ratio and an overall pyrr hotite concentration of 8% (all proportion by weight). Approximately 34 days after drain- age to 15% moisture in natural air flow condit- ions, an unconfined compressive strength of 1.862 MPa was attained. A subsequent experi- ment was conducted with a sample of optimum mix in a pipe one metre long in forced air flow conditions. At a superficial velocity of 3.Om per hour the mix required 155 hours to harden to 1.862 MPa after drainage to 15% w/w moisture content. The pressure drop bet- ween the top and bottom of the mix in the pipe remained constant at 9 KPa/metre length. This result suggests that forced air flow conditions will increase the rate of hardening. No dangerous effluents were detected in the course of the experiments which could affect mine equipment or personnel.

Jan 1, 1973

By J Mukhopadhyay, J Gutzmer

Most world-class high-grade (60 - 67 wt per cent Fe) hematite iron ore deposits are the product of enrichment of Precambrian iron-formations but processes responsible for enrichment are still unclear. Different models, ranging from syngenetic and diagenetic (King, 1989), deep-seated hydrothermal (Powell et al, 1999; Barley et al, 1999; Taylor et al, 2001; Gutzmer et al, 2002) and ancient supergene (Morris, 1980; 1985; Van Schalkwyk and Beukes, 1986) to modern supergene (MacLeod, 1966) have been suggested. The high-grade hematite deposits stand in contrast to martiteûgoethite ores which are generally accepted to be the result of supergene enrichment of iron-formation because they are found along Cretaceous to Tertiary lateritic weathering profiles (Morris, 1980; Harmsworth et al, 1990). Uncertainties about the origin of the high-grade hematite ores appear largely due to the monomineralic composition of the ores. They are almost exclusively composed of hematite (as microcrystalline hematite and martite), a mineral with wide stability field and very simple chemical composition that reveals little about its origin. Second, many of the deposits have been overprinted by later deformation and chemical weathering obscuring primary ore characteristics and zonation (Taylor et al, 2001). Third, surprisingly few detailed geological studies have been undertaken on the deposits with the aim of unraveling ore genesis. Most studies focus on the present-day structure of orebodies and their general physical-chemical composition for mining and beneficiation purposes. A more thorough understanding of the origin of high-grade hematite iron ore deposits may be gained by combining available mining-orientated data with systematic petrographic-geochemical analyses of different ore generations and hematite phases. This paper presents a first summary of results of an ongoing study, started some two years ago, of high-grade iron ore deposits in South Africa, India and Brazil, including a comparison with the rather well studied deposits of the Hamersley Province in Australia.

Jan 1, 2002

Highwall mining commenced in the Appalachian region 50 years ago. With innovative equipment design introduced in more recent times, penetration distances over 300 m are now commonplace. It is only in the last three years that highwall mining has become part of the Australian coal industry. Geotechnical evaluation is an integral part of the Australian procedures, and although still being refined, has already proven its worth. Statutory guidelines have also been prepared for operations in Queensland. This paper explores trends in equipment design, geotechnical prediction, operating techniques and statutory requirements with regard to highwall mining Australia's coal deposits. A quick assessment guide to assist in the evaluation of potential sites is included.

Jan 1, 1992

The standard charge weight scaling laws imply that only one particular delay (that possessing the maximum instantaneous charge) contributes to the ppv. However, the present analysis clearly demonstrates that a varying number of blastholes contributes to the ppv. This number also increases with distance, x, between the blast source and the detector, and is caused by waveform broadening due to attenuation. Thus the operative charge weight, itself, is also a function of the distance, and so makes the standard charge weight laws difficult to implement. If the delay time scatter is neglected, then, under certain conditions, relatively simple expressions can be derived for the ppv magnification, FN, as a function of the number, N, of blastholes. When the influence of delay scatter and random fluctuations in each blasthole vibration is included using Monte Carlo simulations, then, to a first approximation, the condition FN=KNx applies, where KN is a constant dependent upon N. Unfortunately, however, for any particular blast this condition cannot be distinguished from the standard charge weight scaling law. The dependence of ppv on N would only be apparent if blasts of differing N were to be compared in an otherwise identical environment. Since this situation is very difficult (if not impossible) to realise, then the influence due to N, although significant, goes largely undetected. Another problem associated with standard charge weight scaling laws is the difficulty of accurately assessing the appropriate charge weight, even if attenuation broadening is neglected. For example, if a number of blastholes are very close, then they experience a vibration interaction which is non-linear. However, if the same blastholes were to be widely spaced, then the separate vibration signatures add linearly. The standard charge weight scaling law fails to distinguish between such linear and non-linear regimes. Unfortunately, in many production blasts, both regimes exist throughout various portions of the blast spatial pattern and so makes it difficult to determine the operative charge weight. The solution to the combined influence of waveform broadening and linear/non-linear interactions will obviously require substantial future research. A possible solution may be found in the use of numerical dynamic codes.

Jan 1, 1990

Throughout the Kalgoorlie Field the dominant factors influencing all planned exploratory work are: firstly, the general geology of the district, and, secondly, the lode fracture pattern. Superimposed on these, there are innumerable faulting problems which tend to complicate the search for ore.In this paper it is proposed to deal primarily with the lode fracture pattern and to touch on the general geology only insofar as it affects ore distribution. So much has been written on Kalgoorlie geology that it would be impossible to review the literature adequately in a brief paper such as this. The basic facts of rock types and rock distribution are well established and the broad structure of the field is known in the central portion, though it is less well established towards the northern and southern ends.The latest descriptions of the general geology are those of Stillwell (1), and Gustafson (2), -and these represent the basis of current knowledge.GENERAL GEOLOGY.The field is six miles long and about one mile wide, the long axis trending north-west. The "Golden Mile," or heart of the mining 'area, covers a length of three miles in the southern section, and consists of a central core of quartz dolerite greenstone which merges into uralitic quartz 'dolerite on its western margin. The uralitic quartz dolerite is derived from an original quartz dolerite by a low grade...

Jan 1, 1948

By McNay L. M

Two field studies to monitor fill pres sures and vein-wall deformation were conducted in mines of the Coeur d'Alene mining district in Idaho. Both operations employed cut-and-fill mining techniques in nearly vertical veins aver- aging 10 feet in width, and backfilled with classified mill tailings. Hydraulic pressure cells were used to measure transverse, longitudinal, and vertical pressures within the backfilled stopes. Rock bolts extending into the manways and mechanical closure devices were used to monitor vein-wall convergence. Continuous recorders were used with selected pressure cells to prolong the life of the installation. Transverse pressures in excess of 600 psi and stope wall closure up to 22 inches were re- corded. Closure rates were higher at midheight of the stope than they were near either sill, indicating that the vein walls react similarly to a beam supported on each end.

Jan 1, 1973

By G Kuntz, V Wall, B New

The prime aim of the Campbell Mine project was to develop a 3D geological model for the Campbell-Red Lake system to contribute to an exploration model for the region. The base data is composed of over 60 years of geological data covering an area of 16 by 8 km, and from surface down to 1830 m depth. This paper concentrates on the methods used in the GeoSpace system for the processing, integration, display and interpretation of such a large and diverse data set. A block model was developed that recorded the relative frequency of each geological feature within each block. The data input for the block models were based on recoding of the Campbell Mine drilling and channel sample databases into lithological, alteration and structural subsets. The value for each geological characteristic inserted into each block is calculated from all available data that falls within the block. Relative and absolute comparisons of the individual variables provide a targeted outcome from which the blocks are coloured for visual inspection. Different combinations of variable comparisons can be evaluated so that required features are highlighted for interpretation. Blocks are displayed to illuminate the ædominantÆ rock type, according to a formula that may be varied interactively to display the features required by the geologist. This flexibility allows rapid remodelling of lithological distributions, commonly highlighting minor lithological packages not readily visualised in, and interpreted from, drillhole traces alone. The 3D geological model was built from the drillhole datasets and old mine plans utilising standard 3D mining, GIS and database software, with several iterations of plan and sectional interpretation. Near surface bedrock geological interpretations were further constrained by low level aeromagnetic data. The Geospace approach employs an innovative technique for visualisation of the distribution of lithological packages and alteration via block modelling. The method utilises the block model format of data handling as it is considered to be more visible than drilling, flexible enough to incorporate a wide range of data sources, and allows for spatial proximity relationships to be investigated. The method is a simple form of processing large data sets so that results are clearly visible. The calculation is much more rapid than estimation procedures, and does not have any requirement for geostatistical interpretation which is also time consuming. Geospace is not unique to any mine environment software and it is expected to be able to be performed in any system. The proper portrayal of the internal structure of the mineralised body will provide practical input to exploration and mining principally in the areas of resource estimation, exploration vectoring and ore/waste characterisation and may be incorporated with other data to include mine support and mine scheduling.

Jan 1, 2003

'Nothing happens until something is sold' This statement is not original - it is a necessary orientation for marketing industrial minerals. The most important single philosophy of marketing is that it recognises the consumer as the starting point. Production orientation is concerned with producing products that the customer might buy. Market orientation is concerned with finding the needs of the customer and how they can be satisfied. The difference between the two approaches can be recognised in company structures but the most tangible difference is in the approach by a company to selling and development. In other words, it is the market that decides what can be done with a mineral. The markets requirements dictate what mineral, what grade and what price will be paid. Therefore it follows that when pricing a product we should avoid taking the basic cost and arriving at a final selling price through a series of standard markups (unless government insists on it). We should start with the price the market can stand and work backwards to find out whether you have a profitable product or one that will fail because it is too dear. Naturally a thorough understanding of production costs is necessary particularly when marginal markets are concerned.

Jan 1, 1978

By Dyson NF

Nickel sulphide precipitated from waste liquors at the Yabulu plant of Queensland Nickel Pty Ltd was pressure leached under various conditions. Leaching at 130¦C and 700 kPa of air dissolved 95 per cent of the nickel as the sulphate in less than 2 h. Leaching at 130¦C and 350 kPa of oxygen dis- solved 95 per cent of the nickel in less than 1 h. Dissolution was faster with oxygen than with the equivalent pressure of air. Crystallization of hydrated nickel sul- phate from the resulting clarified leachate is readily achieved. Because the sulphide pre- cipitate also contains minor amounts of iron, copper and cobalt, the crystallization product contains these metals in excess of the amounts required for electrolytic-grade nickel sul- phate. This grade of product could only be produced if the contaminants were removed prior to crystallization. Alternatively, the "crude" nickel sulphate could find a market as a feed for the electrolytic production of Ni-Fe coatings.

Jan 1, 1984

The purpose, basic data requirements and various analysis/modelling tools employed for geomechanical evaluation of mine-site conditions are overviewed. The impact and application of computer technology are dis- cussed. Broad guidelines and criteria are presented for establishment of a practical geomechanics data-base system to yield infor- mation suitable for mine design purposes. Future needs of the Australian mining in- dustry are examined.

Jan 1, 1983

Consideration was given to the.applicab on of a solvent extraction circuit to be'included in the process'for the-recovery of a high grade product from.:-the Rum Jungle Creek.South uranium ore body.The economics of two alternative processes, firstly the Eluex process which uses an ion exchange process followed by solvent extraction.-of a.high grade sulphuric acid eluate, and secondly a process using direct solvent' extractioh of pregnant leach liquor, were studied. There was a small cost advantage favouring the Eluex process but when other factors were considered, the installation of a direct solvent extraction process appeared the better long term investment. A solvent extraction plant was installed at Rum Jungle in 1962.

Jan 1, 1963

By R Nakia, R Livingstone

Historically the Goldfields of Victoria produced large volumes of gold. Interest in these historical Goldfields has grown over recent years with a view to restarting production of gold. A notable example of this is the Bendigo Goldfield. There is also interest in the Ballarat Goldfield and Ballarat Goldfields Ballarat East Project is a particular example of this. The aim of this paper is to describe the ventilation aspects of the potential Ballarat East project. The mine is proposed as a decline access. The paper gives an overview of the project and in particular the ventilation planning associated with a number of possible equipment scenarios. The paper also analyses the main ventilation pollutants that are likely within the proposed mine as it develops to increasing depth. An attempt is also made to determine the depth at which mine climate will become the dominant pollutant rather than diesel exhaust pollutants.

Jan 1, 2003

With the post-war expansion of mmmg activities on its Western group of mines, the management of Lake View and Star Limited has commenced a project for the improvement of underground ventilation.The major part of this project is to provide adequate return airways for the ventilation of the deep levels. To this end, the Ivanhoe South Extended shaft is being enlarged, and ultimately an exhaust fan with a capacity of 180,000 cu. ft. of air per minute will be installed at the shaft collar.Prior to 1932, the shaft was used exclusively for baling water from the 800 and 2,000 ft. levels. These two levels are the only ones connected to workings from the Horseshoe lease. After the installation of pumping plant at the Horseshoe Main Shaft, baling was discontinued, and the water was graVitated from dams to the pumps on the 1,000 and 2,000 ft. levels.Water makes into the shaft, through a series of fault planes, between the 600 and 1,500 ft. horizons. The total flow is 16 gal. per minute, of which approximately 7 gal. per minute graVitates to the 800 ft. level. As a big proportion of the water dropped uncontrolled through the shaft, a downcast current of air approximating 20,000 c.f.m. was induced. This air ventilated a limited area of workings in the Horseshoe lease, between the 2,000 and 2,360 ft. levels.In 1938, it was decided to reverse the direction of the airflow in the shaft. Work was carried out to pipe the...

Jan 1, 1948

By Parker C. J, Mikula P. A

The excavation for the Sydney Opera House Parking Station comprises a large donut shaped underground cavern with a central sandstone pillar. The maximum effective roof span is about 19 m and the rock cover is between 7 m and 8 m. Permanent support for the roof and the various services tunnels consists of a combination of tensioned anchors, and untensioned dowels, and mesh with shortcrete and fibrecrete as the final lining. Steel sets were installed at main intersections.Fundamental to the design philosophy for excavation of these spans at such shallow rock cover was the use of monitoring to check on the adequacy of the installed support. Prior to excavation, extensometers, inclinometers, piezometers and surface settlement survey stations were installed. Underground survey stations, anchor load cells and shotcrete pressure cells were installed as excavation proceeded. Excavation commenced at the crown using an initial heading and three widening stages. Geological mapping during excavation confirmed borehole expectations, namely sandstone beds 1 to 4 m thick interbedded with thin shale units. Bedding plane contacts varied over short distances from tight partings to thick brecciated seams. Jointing was subvertical and joints tended to be bed-limited.

Jan 1, 1993

By Szymanski J

The problems associated with underground mining continue to grow in size and complexity. As a result mine management is becoming aware of the benefits that can be achieved through the use of computer-oriented tools for system analysis. When such tools are employed in conjunction with benchmarking practices, the drivers of the system that lead to superior performance can more easily be determined. This paper discusses the use of the Simulation Language for Alternative Modelling (SLAM II) in the determination of the drivers of an underground room-and-pillar mining system. The mining operations included in the model consist of extracting, loading and hauling of the coal using continuous mining equipment in a room and pillar system. Equipment specifications and mining techniques used in the model are based upon current methods employed at the existing underground coal mines worldwide. The model developed is capable of adequately predicting the operational performance of the real world system from a statistical point of view. The results from the study show that computer simulation is an excellent tool for evaluating various mine configurations and for gaining a better understanding of the mining systems.

Jan 1, 1995

By Reichman J, Chapman G

The features of seam gas drainage from the point of view of mathematical modelling are outlined and discussed: 1. The use of conventional single phase gas reservoir simulator for very simplified modelling. 2 Alteration of a conventional petroleum reservoir simulator into a specialised simulator for seam gas drainage. 3. Application. of a conventional petroleum reservoir simulator for modelling of seam gas drainage by the way of pseudo-functions and sacrifying one dimension.

Jan 1, 1982