Search Documents

By C E. Loo

The cohesive zone has a significant influence on blast furnace operation and performance. The high-temperature behaviour of the reducing ferrous burden determines the properties of the cohesive zone and is studied in a laboratory using a softening and melting test. This paper summarises recent work aimed at better understanding the physico-chemical changes in a ferrous bed during softening and melting. Using a combination of standard, non-standard and quenched tests supported by optical image analysis, this work has highlighted some important differences in behaviour between lump, pellets and sinter as well as between the two lump ores and two acid pellets. As with the two lump ores, one pellet is denser than the other and the denser ore/pellet is also higher in silica.Within the cohesive zone, densification of the ferrous layer leads to reduced permeability and greater pressure drop. From the work presented in this paper, two key mechanisms of ferrous layer densification were identified. Firstly, the formation of fayalite, which melts at low temperatures, can act as a lubricant between particles and lead to densification of the ferrous layer under load. Secondly, reduction to metallic iron is topochemical and fayalite in the outer shell of the particle restricts gas flow to the centre and results in the formation of a wustite core. As temperatures rise, the wustite melts and eventually exudes out of the shell, occupying void spaces between particles and further reducing layer voidage and permeability.This work has shown that density and silica content are two key factors that result in increased densification of the ferrous layer. For porous Australian lump ore, the higher porosity and lower silica reduces the formation of fayalite and limits the formation of the wustite core, ultimately leading to a more permeable bed. The difference between the porous and dense ores was more pronounced with the introduction of prereduction to better simulate blast furnace conditions. This suggests that a porous ore gives significantly better cohesive zone permeability and blast furnace operations than a dense ore.The behaviour of fluxed sinter particles is different in that the silica reacts with lime to form dicalcium silicate. Minimal wustite core forms because relict hematite particles in sinter are only small and reduction occurs uniformly throughout the particle. Even with significant loss of material through prereduction, beds formed from sinter remained comparatively rigid. Studies using a typical blast furnace burden mix of 80 per cent fluxed sinter and 20 per cent porous ore showed that the structures of these beds at softening and melting temperatures are very similar to the sinter-only test. Measurements of bed contraction and pressure drop also confirmed that the introduction of 20 per cent porous ore into a sinter bed did not alter its properties. This is an indication that 20 per cent ore can be easily accommodated by blast furnace burdens.CITATION:Loo, C E, 2015. Important acid ferrous burden properties in the cohesive zone of a blast furnace, in Proceedings Iron Ore 2015, pp 367–376 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By J Watson

Electronic detonator technology has been under development for the last two decades. Currently, there are a number of systems commercially available with several others still under development, each with its own unique features. This technology can offer a significant advantage to the drill and blast engineer through their ability to initiate an explosive charge at the æplannedÆ time. This new technology has created huge interest within the drill and blast community and also raised their expectations to produce better blasting outcomes. In many cases, specifications (or even expectations) of desired blast results are not properly defined. Interaction between the input variables (rock mass characteristics and blast design) and results (fragmentation, throw, damage, ground vibrations, etc) and their mechanisms, or relationship to one another, are not very well defined or understood. That is why rock blasting is still considered by many as an art rather than science. With one of the few remaining variables (cap scatter) now controllable, todayÆs blaster finally has the ability to apply science to his trade. Even though electronic detonators are available and becoming more commonly used, current field practices are not always conducive to extracting or deriving the maximum benefit from this new technology. In the authorÆs opinion, the following need to be understood to derive and sustain the maximum value: clear definition or specification(s) of desired outcomes from a given blast; impact of different features in an electronic detonator system (precision, accuracy, flexibility, reliability, etc) and their impact on the desired blasting outcomes; interaction of blast design variables (energy, energy distribution, timing, blast geometry) and their impact on desired outcomes; impact of rock mass variability and quality of blast implementation on the desired blasting outcomes; and critical need to utlilise appropriate tools and systems in order to measure and quantify benefits.In the authorÆs opinion a scientific implementation process is the key to derive the benefits. This paper analyses the industryÆs preparedness to derive the benefits from this technology and proposes a scientific methodology to understand, evaluate and sustain the value from this technology.

Jan 1, 2004

The author describes 1. The classification and characteristics of various thick seam mining techniques in various Japanese coal mines. 2. Practices of thick seam mining methods experienced in Taiheiyo Coal Mine. Currently, thick single lift, simultaneous multi lift and non simul- taneous multi lift mining methods are adopted as underground flat thick seam excavations in Japan. These are now reliable and effective in increasing the extraction ratio. At Kushiro Colliery of Taiheiyo Coal Mining Co., these three thick seam mining methods have been used. According to the results, if solidification of the top lift goaf is essential, the non simul- taneous multi lift mining method is the most effective in increasing the extraction ratio without minimising productivity of each lift and it points out that further development of this method is necessary.

Jan 1, 1976

By Sivell W

We discuss the origin of the Patuki ophiolite complex and the Dun Mountain ultramafics of Middle Permian age in Nelson, New Zealand. It is shown that the Patuki volcanics have strong affinities with tholeiites of mid ocean spreading ridges transitional to alkaline basalts similar to those from fracture zones and ocean islands. At D'Urville Island, typically pillowed alkaline basalts enriched in rare light rare earth elements (LREE) - ophitic spilites - are associated with LREE-depleted (N-MORB-like) tholeiitic spilites with intergranular textures. The metabasalts are associated with a wide variety of sediments, and with sediments are intruded by conformable sheets of serpentinite. Coarsely crystalline mafic and plagiogranitic rocks signify vents and magma chambers, and we propose that the group developed as ocean crust from a slowly spreading mid-ocean ridge, transform association, overwhelmed at intervals by volcaniclastic sediment. Detailed mapping at a scale of 1:5000, and stratigraphic and geochemical development and structural coherence, show that the group is not melange in the Franciscan sense. The Dun Mountain Group, of serpentinites, peridotites, dunites, gabbros and other rocks, intruded the upper Patuki Group as a linear series of aligned pods and sheets. They carried up with them tectonic inclusions of older rock, which were metasomatised, and altered wall-rock, and one low angle dike passed several hundred metres into overl~ing sediment, at moderate temperatures (500 C). The rocks did not act as a floor (and alleged source) for the Patuki, but partly post-dated and were emplaced into Patuki.

Jan 1, 1987

By Poplawski R. F

A 32-channel PSS seismic monitoring system was commissioned at Mt Charlotte mine in 1994, and at the time it was the first such system in Australian mines. The system continuously observes the occurrence of seismic events and locates them accurately in space and time. Mt Charlotte has a history of seismicity, with the largest event in recent years of Richter magnitude 4.3. The decision to 'go seismic' was made despite some uncertainty regarding its potential usefulness. However after the first year of operation, benefits have been realised in terms of less production downtime, improved mine safety and mine planning, and better understanding of the nature of Mt Charlotte seismicity. The seismic network has performed well, recording 550 events in its first year of operation to a location accuracy averaging ¦ 12 metres. System reliability is excellent, with very little downtime, and acceptable operation and maintenance times and costs. Observations show major distinct changes in the rate of mining induced seismicity over time periods of weeks and months. Events have tended to cluster in specific mine areas and on particular faults and structures. Case examples of pillar preconditioning, breakout around an orepass, and a major stope rockburst, illustrate the role of seismic data and the benefits it brings to safety, productivity and planning.

Jan 1, 1995

Underlain by and intruded into the sedimentary rocks of the Transvaal Supergroup the Bushveld Complex is the largest known layered intrusion in the world and contains one of the richest ore deposits on earth. It has been the world's major source of Platinum Group Metals (PGM) since the mid-1900s with Chromite and PGMs the two most economically important components of the Bushveld Complex. The lower group (LG), within the critical zone, consists of seven chromitite layers and it is within this sequence of chromitite layers, the most important target of the lower chromitite group is found, ie the LG6 chromitite unit. The LG6 chromitite unit consists of a chromitite duplex composed of the lower LG6 chromitite layer (Steelport seam), averaging 1 m thick, overlain by a 0.66 m waste parting and a thin 0.34 m thick LG6a chromitite layer (leader layer).Two mining methods are commonly applied in the Bushveld Complex to extract the LG6 chromitite layer package. One method consists of footwall development utilising rail bound equipment to gain access to the orebody and then extracts only the LG6 chromitite layer by means of hand held rock drills and scraper winches. The second method is the use of mechanised equipment to access the orebody on the plane of the ore utilising bord and pillar mining method, which extracts the full mineral resource, ie the LG6 and LG6a layers. Conventional narrow vein stoping is often selected due to the large conventional mining skills base found in South Africa, the perceived cost and dilution implications of utilising mechanised equipment, and the difficulties of using mechanised equipment at dips above 12¦. The driving factor for mechanised mining is the perceived ability to access the orebody quickly and inexpensively, and extract the entire mineral resource package (LG6 and LG6a) while limiting capital expenditure and improving safety.This paper investigates these two commonly applied approaches, highlighting the benefits and problems associated with the two approaches. Comparisons will be made of the two mining methods and recommendations given for the mining engineer to consider before selecting the appropriate mine design.

Dec 6, 2010

By Carter A. J, Miller D. M, Holder N. H M, Van Aswegen P C

The Harbour Lights Mine situated at Leonora in Western Australia, mines a refractory sulphidic gold ore. The main sulphide minerals are pyrite and arsenopyrite. Due to the association of gold with the pyrite and arsenopyrite, gold recovery is not amenable to the normal cyanidation process.A pyrite/arsenopyrite flotation concentrate is produced at Harbour Lights. This concentrate has been stockpiled for the past two years.A bio-oxidation process (BIOX«)* to treat refractory gold flotation concentrates has been developed by GENMIN in South Africa. Harbour Lights acquired the technology from CRL BIOX« Pty Limited in Brisbane, to treat the refractory gold concentrates.

Jan 1, 1992

The New South Wales Department of Mineral Resources has, since 1974, administered the Derelict Mines Rehabilitation Program (DMRP) to reduce the environmental impacts of abandoned and orphan mine sites. The application of the DMRP is presented in case studies of sites from the South Maitland Coalfield featuring residual drainage of acidic and saline water in a semi urban and rural community setting. The acidity here is typically derived from iron oxidation in shallow underground coal mine workings and in surface emplacements of coal washery reject materials. This paper presents summary information on AMD investigation, monitoring and rehabilitation. The experiences of community expectation, stakeholder consultation and peer review are discussed.

Jan 1, 2003

By Sobek S, Lotzien RM

Although the conventional procedures for designing agitator flotation plants are well-known and reliable, little experience for designing modem pneumatic flotation plants has been gained up to now. A reliable procedure originating from graphic methods for the design of distillation columns is presented. Examples demonstrate on laboratory and semi-technical scale the application of this extremely practical method for designing a fly ash and a magnesite flotation plant.

Jan 1, 1993

By Ehlers HK

Mount Isa Mines Limited has 25 rod and ball mills of various sizes installed in two Concentrators at Mount Isa. A continuing investigation into installation, design and materials of liners for these mills has been in progress since the early sixties. Both manual and mechanical methods of liner installation are used and described. Materials for the various applications have been evaluated, mainly by field trials. Design of liners has also been evaluated by field trials and the history of trials in No.4 Concentrator is given. The purpose of the investigation has been to reduce the cost of mill lining and the life of many linings has been greatly increased as a result of this work.

Jan 1, 1978

By Longworth C. R

This paper descrioes a case history of a coal mine which developed un'tahle roof conditions due to mass sliding of the overburden strata on a claystone band within the coal seam. The sliding is believed to have been initiated by stress relief associated with the removal of overburden alongside the entry portal of the underground workings. Once in motion, the roof block was kept moving by bulking due to roof collapse in the normal underground goafing operations. Control measures in the form of an earth and rockfill buttress against the entry portal and a sequential mining plan to create goaf areas alongside the entry portal have been initiated to attempt to limit movement. The operation has been continually monitored and a gradually decreasing pattern of movement is being re, orded.

Jan 1, 1981

The Yabulu refinery of Queensland Nickel Pty Ltd located near Townsville now imports more than three million wet tonnes per year of nickel laterite ore from New Caledonia and Indonesia, making it the largest importer of any commodity in Australia. The project has illustrated that importing untreated bulk ore and re-exporting high value products makes good economic sense for the company and the nation. The economics of this exercise have been considerably enhanced in the past year by changing the project's principal product from nickel oxide sinter to refined high purity nickel metal. It is one of the few operations in the world where nickel ore is transformed to nickel metal at a single site. Several novel technological processes were developed at Yabulu and incorporated into the refinery to allow this product transition to occur. By utilising internally developed technology the new processes were installed at a capital cost of less than $10 million. It is unique for a large nickel producer to completely change the quality of its entire product range many years after the plant was constructed and considerable attention to marketing the new products has been required.

Jan 1, 1995

The problem of manufacturing from sulphuric 'acid and Christmas Igland "A" phosphate, superphosphate of acceptable physical condition and agronomic phosphate availability, is directly related- to the crystallisation of a reac- tion product, monocalcium phosphate monohydrate. Two solutions to the problem, vacuum drying the superphosphate and calcination of the ore before reaction with acid, are discussed.

Jan 1, 1971

By C Tapia Cortez, C Sammut, S Saydam, J Coulton

‘Like every other commodity, the value of the metals is subject to variation’ (Ricardo, 1817). Mineral commodity price uncertainties have always been a significant issue in mining business due to the close relation between global economic conditions and commodity prices, which commonly generates significant and unexpected price fluctuations. Price forecasts have been driven by economic theory, which states that in the long-run market will be balanced and that prices tend to the marginal cost of production. However, this theory has been misunderstood in the mining industry and future prices through time, in real terms, are assumed to be unchanged. This is unrealistic due to regardless of the cycling nature of economy and the omission of uncertainties. Furthermore, using historical data in traditional price forecast approaches does not guarantee realistic predictions as past events will not necessarily be repeated at the same intervals and with the same intensity. Mining, finance and economic sectors have made significant research efforts to predict prices and control uncertainties through classic linear, Gaussian and probabilistic simulation approaches. However, by definition, uncertainties cannot be measured or accurately modelled. Uncertainties can be identified to measure and manage the associated risks; therefore, uncertainties in mining projects have been historically misinterpreted, erroneously measured and poorly controlled. It is widely known that supply and demand functions drive market prices. While technological development noticeably influences supply, demand is strongly driven by psychological factors, mainly related to customer preferences and lifestyle expectations. Thus, human behaviour is one, or if not, the most important variable to determine commodity prices in a competitive market. During the last decades, alternative methodologies have been used to study uncertainties in human, environmental and market behaviours. Chaos theory, fractals, artificial intelligence and econophysics have been widely and successfully used to investigate complex dynamic systems to address uncertainties over time in the fields of neurosciences, meteorology, aviation and market trading. The application of these techniques in the market suggests a more realistic approach to the business environment. Through the combination of the methodologies above a novel long-run price uncertainties simulation approach that emphasise the differences between risks and uncertainties is proposed in this paper. CITATION:Tapia Cortez, C, Saydam, S, Coulton, J and Sammut, C, 2015. Copper price uncertainties – chaos theory to manage risks in mining projects, in Proceedings Third International Future Mining Conference, pp 261–272 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By P Gardner

The Kanowna Belle gold mine in Western Australia has reached a depth of 1000 m on the way to 1300 m. A feasibility study undertaken in 2006 identified the mining of E-Block as both technically and commercially feasible. One of the major risks identified in the study was the ventilation capacity, as the existing primary ventilation system would not support the production schedule for mining and a major system upgrade would be required. Failure to provide the necessary airflow would put the project at risk. A review of the airflow requirements and infrastructure options detailed in the feasibility study was undertaken to ensure that the assumptions and design were optimised. This review recommended a minimum airflow of 206 m3/s, but by acknowledging the necessary constraints imposed by mining at depth and re-engineering the mine layout to optimise the primary ventilation circuit, this requirement was reduced to 160 m3/s. This represents a 22 per cent reduction in airflow and a reduction in capital cost that will see mining at depth become economically feasible at Kanowna Belle. This paper discusses the processes that led to a redesign of the mining layout and highlights the importance of including the ventilation network in the optimisation process.

Jan 1, 2008

By Hutchinson IN

In order for the Australian underground coal mining industry to achieve the high productivity rates demanded of it without compromising its good safety record, improved geotechnical monitoring systems are required. One of the main problem areas affecting underground coal mining is the deterioration of previously stable roadways.CSIRO Division of Geomechanics has been working on a NERDDC funded project to develop an instrument to monitor coal mine roof deformation. The instrument which has been developed, Roof Alert, is a self contained, battery powered, intrinsically safe device. It can monitor the magnitude and rate of deformation and give multiple, variable visual alarm signals where preset levels ate exceeded.

Jan 1, 1991

Thermal Processing of Petroleum Fly Ash for Vanadium Recovery

Sep 13, 2010

The "Line of Lade", a generic term by which the great Broken Hill orebodies are collectively known, lies in the County of Yancowinna, New South Wales (NSW) at the south eastern extrenity of the Barrier Ranges. As the township of Broken Hill grew to a city (incidentally it was officially named Willyama but by exerting an enterprising community independence which is still evident today it outplayed officialdom and retained its descriptive name), two major areas of population developed, Broken Hill and South Broken Hill. These two main civic divisions are respectively north west and south east of their dividing line, the surface expression of the orebody. See Fig. 1. The border between the States of NSW and South Australia (SA) is drawn along longitude 1410 East whilst the city of Broken hill's official longitude is 1410 28' 14" East which means it is only 50 km from this political boundary. A latitude of 310 57' 03" South contributes to the harsh climate of high summer temperatures which is not mollified by any significant increase in altitude for Broken Hill is only 300 m above sea level.

Jan 1, 1983

As mining and extraction processes improve and lower grade ores become economic, mining for most ores have extended to depths beneath the zone of weathering oxidation created over geological history. These deeper openings expose sulphidic formations and reduced mineral species as either primary ore or simply as accessory or gangue minerals in the country rock. This is not new, underground mining for primary base metal and gold have long been familiar with these problems, as have coal and uranium miners. The change is simply that the number of mines exposing sulphidic waste rocks, tailings to the atmosphere and/or leaving behind dewatered sulphidic rock surrounding the mine void has increased the number of sites from where acid mine drainage (AMD) may emanate with consequential problems for the hydrological environment including downstream catchments (Miller et al, 1996). The principles of ecologically sustainable development (Brundtland, 1987) have been more or less ratified by all the developed nations of the world and this has led, amongst other things, to an expansion unprecedented in the research and documentation of means for achieving long-term environmentally acceptable stabilisation of solid wastes of all sorts. These have revealed that AMD problems can be minimised and even reversed in many cases by the integration or co-disposal of biodegradable organic wastes with oxidising sulphidic wastes (Elliott et al, 1996). This paper considers how this might be achieved at mine sites in Australia and the results encountered at some relevant sites.

Jan 1, 1997

By Koppe J. C, Dimitrakopoulos R, Costa J. F

Grade control and the delineation of ore/waste in open pit operations is traditionally based on the comparison of estimated grades with an economic cut-off. This paper deals with an alternative approach to grade control based on estimating gra

Jan 1, 1998