Search Documents

In many mining operations, the truck and loader equipment represents the bulk of the invested capital and the majority of the mine operating cost. The profitability of these mines is therefore critically linked to the efficiency of the truck and loader operations. The various factors which affect the productivity of trucks and loaders are analysed by computer simulation, and the results presented in a form allowing assessment of the importance of each factor on overall productivity.

Jan 1, 1983

By Rogers J. F, Bird A. C

The establishment of vegetation for dust control on tailings dams at The Zinc Corporation, Limited and New Broken Hill Consolidated Limited (ZC/NBHC) is outlined. The evolution of practices and techniques employed is described and the problems encountered are discussed.

Jan 1, 1983

By Keyte SG

Gravity methods of recovering alluvial gold are not very efficient at particle sizes below about 0.1mm. Whereas such gold may not have been economic to recover in the past, the same may not be true today. Centrifugal concentrators, like the Knudsen and Knelson bowls, are showing promise after an inauspicious start, at least in New Zealand. The large proportion of heavy mineral in many auriferous beach sands and the natural hydrophobicity of fine gold should make flotation an attractive contender for its recovery. The conventional mechanical flotation cell is effective, but roughing, scavenging and cleaning are necessary to achieve both high recovery and low mass yield. More problematic is the difficulty of maintaining coarse and dense sands in suspension. The air sparged hydrocyclone is effective at recovering fine gold from a fine Colarado River sand, but is not effective for the coarse and dense beach sands of New Zealand. The flotation column shows much promise for these sands, when recoveries of over 80% and mass yields of less than 1% can be achieved in a single pass. The froth separator of the USSR and flash flotation could also be worthy contenders. It is felt that flotation could be limited to naturally and artificially de-slimed concentrates.

Jan 1, 1990

By Woodlands W. K

A 3D graphics modelling system has been applied to longhole stope ring design at Z.C. Mines, Broken Hill, NSW. This has been in operation for a four month period (January, 1988). The purpose of this application was to provide computer assistance to mine planning engineers and blasthole design draftsmen for the longhole design process, particularly by: 1. reducing the- volume of tracing, drafting and geometric manipulation which is a significant feature of the manual design process, 2. providing additional design drawings to enhance the conception and implementation of stoping design.

Jan 1, 1988

Jan 1, 2004

Electron paramagnetic resonance provides a fast method to characterise quartz. Quartz from veins associated with the Cambrian massive sulphide deposits in the Mt Read Volcanics of western Tasmania and from Devonian reefs associated with gold mineralisa- tion at various localities in Tasmania exhibit specific EPR patterns, different from quartz from common veins. The intensity of the EPR spectra of the quartz can be used as a statistical guide to gold mineralisation at Beaconsfield.

Jan 1, 1987

By Komosa T, Muir D. M

Adequate levels of dissolved oxygen are essential for efficient gold dissolu- tion. The actual levels in plantpuips can be seriously reduced by the presence of oxygen consuming reactive minerals, and reduced oxygen solubility in saline water. The rate of gold dissolution is then limited by oxygen availability rather than cyanide. Ion selective electrode dissolved oxygen meters can give an effective indication of the relative oxygen saturation, but they are not able to give meaningful values of dissolved oxygen in saline water, without custom calibration curves. When the dissolved oxygen concentration is rate limiting, the addition of oxygen or peroxide can improve gold leaching kinetics as well as reduce cyanide consumption.

Jan 1, 1991

By M A. Harrington-Baker, J M. Trudnowski

Sulfate-reducing bacteria (SRB) have the ability to immobilise dissolved metals by precipitating them as sulfides, provided that a favourable biochemical environment is created. Such an environment includes the presence of sulfate, anaerobic conditions and the availability of organic carbon. If such conditions are engineered within a reactive barrier or field-bioreactor, most metals can be effectively removed. To demonstrate this concept, three passive SRB field-bioreactors were constructed in 1998 at an abandoned mine site in the vicinity of Butte, Montana, USA to treat acid mine drainage with characteristic elevated concentration of metals and low pH. Performance of the field-bioreactors, using aqueous samples, was monitored over 32 months until the project was terminated, field-bioreactors were decommissioned and solid matrix sampling of the reactive matter was performed. The most important analytical results are presented in this paper together with conclusions regarding the appropriateness of the field-bioreactors construction features. Only Zn, Cu, and Cd were being removed as sulfides due to SRB activities. Changes in concentrations of other metals (Fe, Mn, Al, As), which do not necessarily precipitate as sulfide, seemed to be affected by SRB only in an indirect manner by responding to increased pH caused by SRB activity. An innovative cellular containment system used for placing organic matter worked very well in preventing settling of the organic matter and ensuring uniform flow of AMD throughout the entire cross-section of the organic carbon with no preferential flow paths This demonstration was funded by the US EPA and was jointly administered by the EPA and the US DOE under DOE contract number DE-AC22-96EW96405. The project was implemented by MSE Technology Applications, Inc, Butte, Montana, USA.

Jan 1, 2003

Miners and mineral explorers are concerned at the increasingly hostile environment being generated towards their industry and their profession. There is little official or public recognition that the mining industry is essential for the maintenance of the country's standard of living; a large part of this hostile feeling is caused by the assumption that mining destroys large tracts of our attractive countryside. This paper presents a historic review of the impact on the countryside of the major land using groups commencing with the Polynesian migration. European farming practices, subsequent expansion of the urban dweller and the land management practices of the two Government Departments, Lands and Survey and New Zealand Forest Service who between them control half of the total land area, are discussed. Estimates of total land area to date, directly and indirectly affected by mining have been calculated and a broad estimate of 18 000 ha or 1/1500 of total land area is indicated; current annual mineral production requires some 240 ha. These gross areas take no account of subsequent land rehabilitation, its improvement upon the original in some cases and the recreational, historic and aesthetic areas gained. Comparisons are then drawn with some current land practices in New Zealand.

Jan 1, 1977

By J Vann, C Seymour

Geology is generally treated as a æfront endÆ step in mine development. After infill drilling, the majority of resource estimation, mine-planning, development, mineral processing strategies and operational procedures are planned and implemented with little geological input, particularly in open pit operations. However, significant benefits in overall costs, cash flow, and technical risk reduction can be realised when sound geology is utilised more rigorously throughout the mining process. This under-utilisation of geology in the mining process has arisen due to a combination of factors:A lack of interest in, or knowledge of the full mining process by geologists. Few geologists fully understand where their inputs make critical impacts on downstream users. As a result of this, geologists generally do not focus their inputs towards areas of greatest value added, ie addressing issues critical for other members of the mining team. Most importantly, few geologists effectively communicate their results to the downstream users of their geology models. The results are that the potential benefits of geology, and the appropriate status of geology in the mining industry, are not fully realised. It is fundamental to realise exactly what geologists do. Geologists constrain geological processes and geometry. All geoscientific tools at the geologistsÆ disposal are geared towards one of these goals. An emphasis on geological processes is present throughout the exploration process, whereas in the resource estimation and mine development process an emphasis on geometry is required. The mining process is a web of disciplines that are attempting to optimise development of a resource to provide value to shareholders. Yet few people within these disciplines have a full appreciation of this web, and where sound geology inputs can add value through various feedback loops. Geology inputs do not end at the resource estimation stage, nor are they relegated to grade control implementation. If geologists have an appreciation of the mining process and close liaison with the other disciplines such as geostatistics, geotechnical engineering, hydrogeology, and mining engineering, they can significantly benefit project costs, timelines, and constrain technical risk by addressing their issues at the earliest possible stage. Furthermore, the mining process is not a single pass timeline, but an iterative process where the exploration, resource definition, mine planning and mining loop is continually repeated over the life of a project. Therefore, the potential inputs of geology are critical throughout the mining process. Effective communication of the impacts of geology inputs on downstream users is often lacking on mining projects. The most effective way to communicate geological results is through where it impacts most û project risk. Focussing all geology inputs and communication in terms of potential material risk allows the geologist to be more effective in contributing value to the mining process, and allows the downstream users of geology inputs to better constrain the risks associated with their aspects of the mining project. Through a program of geologists:taking an interest in the entire mining process and identifying critical areas for geology inputs to downstream users (the geologistsÆ clients); focussing geology inputs to address the potentially material issues on mining projects; and communicating their inputs to the æclientsÆ in terms of technical risk, geology will be much better integrated into the mining process. As a result, the potential benefits of geology throughout the mining process will be realised, and the status of geologists within the mining process will be elevated to a more pivotal position.

Jan 1, 2000

By Anderson DR, Tassell G

A major environmental impact study carried out in the sand dunes of eastern Cape York used image analysis of remotely sensed data to both select sites for ground investigation and categorise the different ecological units present. The approach adopted was particularly suited to the type of environment in question and allowed a high degree of quantification, at a high level of confidence, at costs several orders of magnitude less than conventional Methods.

Jan 1, 1987

Much of New Zealand is comparatively young geologically in the sense that it has only recently been uplifted. In many places young marine sediments are to be found at high altitudes, as evidenced by the existence in the North Island of Pliocene shell limestones which form prominent escarpments at altitudes of about 3000 ft. inthe central part of the Island, and remnants of the same formation found on the summits of the northern Ruahin.e Range at altitudes greater than 4000 ft.

Jan 1, 1962

The Mineral Research Centre is located at Perth in the suburb of Waterford, adjacent to Curtin University of Technology and within a Technology Precinct which includes Technology Park. The Centre, constructed by the WA Government at a cost of $16 million and occupied in late-1994, comprises three separate buildings housing the CSIRO Division of Minerals, Curtin University's School of Chemical Engineering and the Mineral Processing Laboratory of the Department of Minerals and Energy. The emphasis on R&D at the Centre is primarily in hydrometallurgy as a result of staff expertise, extensive bench and pilot-scale facilities, track record with the industry and, very importantly, two of the occupiers being partners in the AJ Parker Cooperative Research Centre for Hydrometallurgy. Staff in the Centre have a long involvement with R&D agencies such as AMIRA and MERIWA. The hydrometallurgical focus of the Centre complements that of pyrometallurgy at the GK Williams CRC in Melbourne and the Centre for Mining Technology and Equipment in Brisbane, to ensure that the mineral processing industry in Australia has access to a complete range of expertise and facilities to serve its needs.

Jan 1, 1996

By Hunter T. C

The wirebar furnacing and casting facility commissioned in 1970 at Copper Refineries Pty. Ltd. (CRL), Townsville, comprising a 70 tonne/ hour ASARCO shaft furnace and a Walker type casting wheel, contained several unique design features. Since commissioning, effort has been directed at improving metallurgical control of the casting process. This has resulted in the identification of optimum mould lubricant properties and the use of continuous on-line measurement of molten metal oxygen content. Casting defects such as cracks and surface porosity are readily explained and controlled using these techniques.

Jan 1, 1977

Against a background of deeper pits, the introduction of prestripping fleets and the need for closer control of operating costs (especially the waste removal component), Australian coal operations utilising draglines have in recent years become increasingly focused on:1. assessment of more efficient excavation methods; and2. application of explosive products and initiation systems which offer more flexibility than ever before.Additionally, developments in blast performance assessment techniques and equipment, and computer modelling and excavation monitoring systems have provided an improved opportunity to design a blast to achieve a desired profile suited to the excavation equipment and Sequence.

Jan 1, 1992

Over the longer term, the adoption of new technology is an essential component in the endless tasks of reducing mining costs, improving safety and improving environmental standards. However the choice of which of the many available new technologies to adopt and which not to adopt is not easy and the price of mistakes can be very high. The most important issue for mine developers faced with making such choices is knowing whether or not a new technology has been developed to the stage where the timing is right for its adoption. A system for categorising new mining technologies is provided. It provides a basis for more easily reaching common understandings about various new technologies and the background information supplied provides an understanding of what it takes to get new technologies to the proven stage and the risks of never getting there. Wherever possible, new full-scale mine developments should not rely on unproven technologies. Approaches to handling situations where a proposed new mine development is not feasible on the basis of proven technologies are also provided. If any commitment to the use of unproven technologies is made, a guarantee of high quality development support from the supplier of that technology is essential. Several case studies of successful and unsuccessful new technology development programs at BHP are Provided.

Jan 1, 1997

More and more coal in Australia is extracted by underground mining methods especially by longwall mining. These methods can be particularly sensitive to relatively small-scale structural discontinuities and variations in roof and floor rock character. Traditionally, information on these features has been obtained through drilling. However, this is an expensive process and its relevance is limited to the immediate neighbourhood of the boreholes. The geological uncertainty remains. Seismic surveying, especially by 3D seismic, is an alternative tool for geological structure delineation with growing credibility. In fact, it is one of the most effective geophysical methods available for identification of geological structures such as faults, folds, washouts, seam splits and thickness changes which are normally associated with potential mining hazards. Seismic data even can be used for stratigraphic identification. The information extracted from seismic data then can be integrated into mine planning and design. In this paper, we demonstrate computer aided interpretation techniques for maximising the information from seismic data and illustrate the ability of seismic reflection methods to resolve localised geological features. Both synthetic and real seismic data obtained in recent 2D and 3D seismic surveys from Australian coal mines will be used. Compared with results obtained with drilling programs, the structural definitions from seismic are of unprecedented quality.

Jan 1, 2002

By Mousset-Jones P, McPherson M. J

Underground airways are characterized by irregular shape and uneven surfaces including large-scale natural roughness, fractures, and a super-imposed sand roughness. Swirls in the grooves of the wall and separation because of the periodic variation of the open cross sec- tion, due to the blasting patterns, make it almost impossible to calculate average con- vective heat transfer computationally on the bases of the geometrical description of the surface. However, dimensionless friction factors can be used to characterize the surface effect of an airway and an analogy between heat and momentum transfer can be applied to calcu- late an average convective heat transfer Coefficient.

Jan 1, 1988

This paper summarises the results of a study carried out for the Sustainable Minerals Institute, University of Queensland, aimed at identifying the major water-related issues facing the minerals industry internationally and the research required to support the development of practicable solutions. An overview is given of the sources and uses of the worldÆs water resources and of the regional and global sustainability of water supply and management. Agriculture is the worldÆs major user of water; it wastes more water than the minerals industry uses. Water reform and its potential impact on the minerals industry are discussed with particular reference to Australia and South Africa. The sources, uses and management of water on mine and processing sites are outlined. Particular attention is paid to the importance of groundwater as a source of often saline water that can be used in mineral processing and for other purposes. Aquifer storage and recovery has the potential to help conserve water resources. Generally, the major uses of water on mining and processing sites are for mineral processing and refining and for the associated tailings disposal. Water consumption for these purposes may be reduced by recycling process water, using saline water, paying close attention to water management, thickening tailings and using techniques such as dry stacking and paste. A change in the minerals processing paradigm in respect of water use could come through research into new, improved and less costly dry processing techniques. The treatment of mine and processing water will be required increasingly before water is reused, stored, discharged or sold, and before sites are decommissioned. Research and development are required to reduce costs and develop new treatment methods. Mine closure and decommissioning raise a number of long-term water issues requiring continuing generic and site-specific research and development.

Jan 1, 2003

By P Cundall

Three-dimensional DEM (Distinct Element Method) simulations were conducted in order to examine the performance of screw conveyors, which are installed to transport bulk materials as parts of many industrial machines, including mining and construction machinery. To apply the DEM to the analysis of screw conveyors, we added a spiral object and cylinder objects, which correspond to the helical screw, the casing pipe, and the driving shaft of a screw conveyor. These objects are represented analytically to enhance the precision and efficiency when calculating the interaction between objects and particles. Simulations were conducted for some real applications: inclined and other types of screws, as well as the basic types (horizontal and vertical). Results were compared with previous work and empirical equations. It is concluded that this method is sufficiently well-developed and useful to analyse various kinds of screw conveyors.

Jan 1, 2000