Search Documents

By Eckersley J, Boyd G

A brief review is presented of the mechanisms and causes of spoil pile failures which have occurred at the Goonyella Mine. In particular, the results of a recent geo- technical investigation of the spoil dumps in the Cleanskin pit are briefly presented. Spoil pile hydrology is discussed in relation to the use of effective stress concepts in the analysis of spoil pile stability. Experience in relation to stabilisation of dragline dumps is discussed as well as the likelihood of current techniques being success- ful in the prevention of gross failures if prestrip material is placed in existing spoil piles. Parameters exerting a major control on dump stability are outlined.

Jan 1, 1981

Oxygen is required for the leaching of gold ores in cyanide solutions. The source of this oxygen demand and the effect of dissolved oxygen concentration on the rate of the process are briefly reviewed.A method of measuring the oxygen consumption rate is described and some experimental results reported.Fundamental aeration theory and rating of aerators is summarised to show how this type of experimental work provides the basis for full-scale design of aeration equipment.

Jan 1, 1984

Traditionally trucks have dominated haulage in open pit mines. Only recently have conveyors begun to be used in the long haul and high lift duties of surface mines. Steep angle conveyors are proven versatile systems for elevating or lowering materials continuously at steep angles to 90¦. This paper describes the design of a bucket-type steep angle conveyor that was developed as a joint research project between the Western Australian School of Mines and the Maanshan Institute of Mining Research in China. The steep angle conveyor can be used as a viable option for transporting blocky ore from open pit mines. A pilot conveyor was constructed and tested to determine its technical and operational feasibility. Furthermore, a computer model based on Matlab mathematical modelling software was developed to simulate the performance of the pilot conveyor. The model enabled to determine the design parameters of industry-scale conveyors to yield satisfactory performance. These conveyors become very cost-effective for those mines having large mine lives and depths greater than about 500 metres.

Jan 1, 2003

By Freeman NV

The concept of an in stream analysis probe was developed at The Zinc Corporation (now Z.C. Mines) in the late 1960's and commercialised quite rapidly, by Phillips and then AMDEL, as an alternative to the established centralised systems (Courier, etc.). The developments which have taken place since that time are reviewed and current procedures and performance are described. An audit of the system, recently undertaken by AMDEL, has highlighted areas where improvements can be made. In 1988 the ISA system will become an integral part of a substantially upgraded process control system.

Jan 1, 1988

By Houchin MR, Jenkins DH

This paper examines the importance of processing to the properties and performance of high purity zirconia ceramics. Many of the principles discussed, however, apply to ceramic processing in general. For fabricated ceramic articles to display their wide range of high performance properties, they must be made fully dense. The precursor powder and postpowder processing requirements necessary to achieve full density in the fabricated body are discussed. Brittleness, the anathema of ceramics, can be overcome in zirconia by incorporation of toughening mechanisms. Transformation toughening and microcrack toughening and their origins in partially stabilized zirconia are reviewed.

Jan 1, 1989

By Whincup P

Hilton deposit comprises en-echelon silver-lead-zinc orebodies with reserves in excess of 50 million tonnes. The host rock to the ore is a dolomitic and pyritic shale/siltstone which dips steeply west. The shale/siltstone is deeply leached and porous, particularly over the Ore Zone where the depth of leaching continues down to 440 m below surface, and constitutes an extensive permeable aquifer system containing a large volume of saline acidic groundwater. Initial production commenced at Hilton in 1987 well below the aquifer. A dedicated dewatering and monitoring programme is in place to ensure security of stoping operations and allow extraction of ore close to the leached zone in future years. Dewatering is undertaken from controlled bores from underground sites. Mine groundwater discharge is presently at the rate of 4000 kl/day with plans to increase to 8000 kl/day. An additional 2000 kl/day of fill and service water and water from secondary aquifers is also pumped from the mine daily. Although recharge rate to the aquifer is minimal, studies indicate that due to the size of the aquifer and future extensions to mine development, dewatering will be a life of mine activity. The investigations which have been undertaken to determine optimum dewatering techniques and schedules are described. These include production bore tests, mine planning constraints and computer aquifer modelling. Gravity geophysical techniques have been successful in delineating the lateral and vertical disposition of the aquifer. The mine dewatering schedule, whose principal component is underground mine drainage, is also outlined.

Jan 1, 1988

The Prospect to Pipehead Tunnel is a component of the Sydney Water Board's multi-million dollar Drinking Water Quality Program to improve the quality of Sydney's potable water supply to meet revised national health guidelines. The tunnel project involves the construction of seven kilometres of 3.9 metre diameter machine bored tunnel which is to be lined with a three-metre diameter steel liner. The paper describes the fully integrated planning and design approach and management technique used to enable this major project to proceed to meet the requirements of a tight construction program.

Jan 1, 1993

By Lawson F

The Australasian Institute of Mining and Metallurgy is a society of engineers and scientists formed in 1893 (incorporated by Royal Charter in 1955) to advance science and engineering in the mineral industries, and to facilitate the exchange of information and ideas to enhance the professional excellence of its members. The Institute has several grades of members. The professional members are linked with Student and Company Members, as well as an Affiliate grade covering other professionals and non-professionals with experience in the mineral industry. The diverse group covers all sections of the mineral industry, from exploration through production to marketing of minerals and petroleum. Corporate (professional) membership also covers science and engineering professionals from specialisms other than the "traditional" ones in geosciences, mining and petroleum engineering and metallurgy. The Institute has Branches throughout Australia, New Zealand, Papua New Guinea and Oceania, whose activities complement the corporate occasions arranged for the benefit of all members by Headquarters in Melbourne. Members are drawn from all sections of the industry - private enterprise, government, research, education, and the support sector, including consultancies, manufacturers and suppliers. Membership of The Institute allows professionals to contribute to their profession through participation in The Institute's seminars and conferences, its many committees and Branch meetings, and through contribution to its many high standard publications. The Institute is the main body for the accreditation of professionals in the minerals industry. The activities of The Institute are directed towards the achievement of professional excellence. It provides opportunitites for contact with, and professional support from, colleagues, and the interchange of information on the latest industry developments.

Jan 1, 1989

By Peck W

The tunnel alignments investigated for the Gosford Regional Sewerage Scheme are located in the Terrigal Formation and are covered for most of their length by a thick blanket of soil and weathered rock. The following techniques were found to be most effective in geotechnical investigations for tunnelling in this area: air-photo interpretation, seismic surveys to pinpoint drilling targets, in-situ measurements of strength,deformation modulus and permeability in cored holes, and the construction of rock- mass models. Cross-hole seismic modulus measurements, surface resistivity soundings and electric well-logging techniques were found to have limited applicability due to adverse local conditions.

Jan 1, 1976

The constructionhunnelling industry in Hong Kong has taken an upturn during the last few years due to the commencement of works to relocate the International Airport to Chek Lap Kok Island. The Airport Core Program consists of ten individual projects including roads, landfill, bridges and tunnels to build the airport and link it to the mainland of Hong Kong. Part of one of these projects is Cheung Ching Tunnel located on Tsing Yi Island. The proposed tunnel consists of a 1.6 km twin tube road tunnel through the island's central ridge, taking three lanes of traffic each way. Each tunnel is 16 m wide - (the widest road tunnel in Hong Kong) and are 10 m high. ICI Explosives (China) saw an opportunity to supply bulk explosives to the Cheung Ching tunnel and contacted ICI Australia to determine availability of a bulk system for tunnel blasting, and assist in its introduction. This paper discusses the methodology behind developing that bulk system to suit a large tunnel drill and blast operation. It also looks at the problems encountered along the way, from the development of the product to the application of the system in the tunnel and the eventual success of introducing a bulk system into a large tunnelling project.

Jan 1, 1994

By O Omidi, P D. Katsabanis

The effect of delay time on fragmentation has been discussed for a long period but rarely in a satisfactory and unbiased way. Despite the efforts of many researchers, delay selection for fragmentation improvement or optimisation remains a controversial issue. Large-scale tests have been plagued with scarcity and scatter of observations, while small-scale tests have been associated with boundary effects and energy losses. Theoretical work is often used to produce explanations for available measurements or tries to simplify wave propagation and wave interaction to guide observation and practical work. The present work analyses results obtained from a relatively large number of small-scale experiments in blocks made of grout, and re-analyses results of previous experiments, to conclude on the effect of delay on fragmentation. It is shown that the main contribution of the delay is found in the fragmentation of the larger fragments of the blast, while the small fractions show almost no effect. Samples, where copper liners were used to inhibit penetration of detonation products in the rock mass, showed effect of delay only when short times were used and steady but poor fragmentation when long delays were used. Based on small-scale experiments, it appears that the fragmentation is optimised when a hole fires prior to the radial cracks, produced by the previous hole, reach the free face of the blast. Gas penetration may result in the development of few more fractures that affect the fragmentation of the largest particles of the blast.CITATION:Katsabanis, P D and Omidi, O, 2015. The effect of delay time on fragmentation distribution through small- and medium-scale testing and analysis, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 715–720 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Chappel R. A, Fishburn B. R

The Eastern Distributor Tunnels - the first major road tunnel project in Australia - are the preferred solution to traffic congestion problems, when compared with alternatives, in this inner urban environment. This is because of the reduced impact on residential housing, the improvement of the existing environment, less restrictions on future developments, and a reduction in noise and pollution. Developments leading to a tunnelled solution, traffic needs and reasons for route location are discussed. Criteria for design of tunnel alignments and geometry are described, including the restraints imposed by surface connections on profiles and grades resulting in low rock cover at tunnel portals. The main geotechnical restraints are a major weathered dyke at the shallow large span underground fork and the weathered Ashfield Shale capping the Hawkesbury Sandstone at a portal. Rock cuttability and excavation methods are discussed. Roadheader machines are the most suitable for the varying shallow arched cross sections required and the tunnel lengths involved but the use of blasting in special situations cannot be ruled out. Initial support for the major tunnel lengths will be provided by rock reinforcement in conjunction with shotcrete. Steel ribs are proposed in areas of low cover and weak ground. Final support will comprise an insitu concrete lining. Construction concepts and special tunnelling methods required at the shallow underground forks and tunnels are described.

Jan 1, 1987

The selection of an appropriate mining method should take into account the geometry of the deposit and its physical properties. Other factors which assist in the determination are the requirements for flexibility in the mining process, minimisation of risk factors and maximising the financial return. Several established mining methods exist which can encompass the requirements to deliver the optimum mining method, this can be in both an underground or open cut environment. The objective is to outline these methods and where they can be applied in a mining project.

Jan 1, 1997

This paper presents a review of computer techniques for the automatic contouring of geological and geophysical data with output as interactive display on graph plotters or graphics terminals and passive display on automatic drafting tables. The advantages of the method of fitting a triangulated surface to randomly distributed data using an advancing front algorithm are described, as well as the technique for determining interpolated values for the production of contour line segments and a contour smoothing algorithm. This contouring method is employed by the Geological Survey of Queensland and is implemented as an interactive system. An alternative method ideally suited to randomly distributed data involves the use of piecewise parametric cubic splines. This method which is ideal for sharp variations in magnitude and areal extent typical of geophysical anomalies is discussed. The mathematics of surface interpolation using non-parametric splines and an explicit piecewise surface fitting technique are discussed. Curve tracing techniques which are suitable for automatic contouring are also presented and the inherent advantages of interactive contouring using on-line plotters and graphics terminals for previewing of displays are described.

Jan 1, 1977

By Fowler T. J

Examples are provided of discontinuity analysis at selected sites in central Victoria. Discontinuities are rock fractures of low tensile strength, including bedding, foliations and joints, which are analysed during rock excavation design, to quantitatively determine the defect orientations, spacing and lengths. Their analysis can reduce the cost of mining operation and improve safety. Extrapolation beyond the exposed face is required, although difficult without an understanding of the regional geology. For rock engineering purposes assumptions are commonly made that discontinuity characteristics are uniform throughout the rock mass, however this is often invalid, as rock masses have usually undergone large-scale deformation, exhibit anisotropy and inhomogeneity. Structural geologists are able to interpret large-scale deformation responses for the purposes of structural correlation and extrapolation. Examples of discontinuity analysis linked to regional geological assesment from sites in central Victoria, reveal that discontinuities exhibit similar characteristics in a range of rock types of different ages and composition. Spacing variations between individual sites are believed to be a result of local rock type differences.

Jan 1, 1997

By D K. Weatherley, A N. Mainza, I Govender, L M. Tavares, M S. Powell

It is understood that rocks do not instantaneously transport along a grinding mill and are consequently not perfectly mixed, but this is conveniently overlooked in mill modelling. A lack of understanding of the transport phenomenon and the difficulty of modelling realistic transport in a complex tumbling system, contribute to this. Visual observation of segregation in AG and SAG mills and measured lag time of mill response to changes in feed provide evidence of the influence of axial transport within mills. Incorporating this lag in dynamic models should underpin dynamic simulation of milling circuits for design and for model-based control. Limitations and errors in predicting the influence of increased power via mill length versus diameter, inability to predict pebble production, and a lack of the differential in residence time across rock sizes and competences, all contribute to inadequate design prediction that can be especially acute for large Autogenous mills. Examples of dramatically under – and overloaded pebble regrind circuits and the inability to predict pebble load in AG milling discouraging the application of this energy-efficient option, point to the need for predictive modelling of breakage by competence linked to transport through and out of mills. Incorporating progress in granular flow and mixing, coupled to computational advances enable models to be based on complex breakage and transport models at high spatial resolution. This allows mechanistic models to simulate thousands of times faster than real time, opening the door to more accurate mill design, including dynamics in process simulation and to live simulation for process control – all with advanced mechanistic models. The value of grasping this opportunity is not easily refuted.

Aug 24, 2022

The paper describes the reasons for developing, specifically in South Africa, dense medium processes to allow baths to operate at low (about 1,35) and high (about 2,0) cut points. Low density processing was developed to meet the demand for low ash coals; high density processing was developed to enable heavily contaminated raw coals, destined to be burned in captive power stations, to be de-shaled without loss of combustibles. The anticipated and actual technical difficulties of operating baths at such density extremes are described, and the results from operating plants outlined.

Jan 1, 1987

By Cooper W. C, Stokes M. A

Proterozoic gold deposits in the Pine Creek Geosyncline are at present receiving renewed attention with the opening of old mines and several new discoveries. This important polymetallic province contains occurrences of gold, base metals, tin, tungsten, tantalum, platinum, palladium and aluminium. These resources have been exploited over the past century with periods of major interest during the turn of the century and during the past 20 years. Economically viable resources of predominantly gold, eg Pine Creek, Woolwonga, Brocks Creek and Union Reefs, and Ag-Pb-Zn, eg Woodcutters are currently in development or being mined. A variety of genetic models, ranging from magmatic through hydrothermal to syngenetic, have been postulated in the past for the formation of gold deposits in the Pine Creek Geosyncline. The first discussion on the regional geological factors that control ore deposition in the Brocks Creek-Howley District was by Sullivan and Iten (1952). They recognised that the most important ore deposits are associated with anticlinal and domal structures and that granites may be a controlling factor in the localisation of the mineralisation. More recently a group of authors, Needham and Roarty (1980), Goulevitch (1980), Nicholson and Eupene (1984), Sanger-Von Oepen, Friedrich and Kater, (1988), Nicholson and Eupene (1990) and Kruse, Whitehead and Mulder (1990) have suggested an exhalitive syngenetic origin, or remobilised syngenetic during dolerite intrusion and/or regional deformation, for gold mineralisation, especially those associated with South Alligator Group lithologies (eg Bridge Creek, Mt Bonnie group of mines and Cosmopolitan Howley). Studies carried out at the Bridge Creek and Western Arm Prospects over the last three years suggest that syngenetic models for gold mineralisation are less relevant to gold mineralisation in the Howley District than first thought (Wall, 1989; Partington, 1990). The Bridge Creek prospect has been cited as an example of a syngenetic-syngenetic remobilised deposit (Oepen, Friedrich and Kater, 1988) while the Western Arm prospect is more clearly a vein hosted epigenetic deposit and a comparison of the styles of mineralisation at both prospects will be made. The nature of the gold mineralisation at both prospects will be described and compared, and possible genetic models for gold mineralisation and their relevance to regional exploration discussed.

Jan 1, 1994

By Kuipers A. J

Aberfoyle has been applying computer methods to mine geology in small to medium-sized underground mines since the early 1980's. Recently, the installation of DATAMINE software at the Hellyer Mine in Tasmania has allowed development of computerised applications which assist both mine geologists and mine planning engineers on a daily basis.Comprehensive data is entered into a database prior to survey coordinating to produce a processed database which can be accessed for construction of a variety of plots. The folded and faulted nature of the orebody contacts at Hellyer has necessitated the use of the structure contour method to provide a complete 3-D spatial interpretation. Computer-generated contact intersection points are hand-contoured before digitising and wireframing as a digital terrain model. This wireframe model can be sectioned in any plane for mine planning.

Jan 1, 1990

By Lightfoot BW, Wand PD, Towne DV

Sampling and e.m.f. probes were used in the liquid flow from the blast furnace and in the forehearth to evaluate the performance of the copper smelting system at E.R. & S. Significant variations in temperature, oxygen potential and copper content with slag depth and with position in the forehearth indicated that convective currents were causing considerable stirring in the forehearth. This was attributed to temperature fluctuations in the stream from the blast furnace, which resulted in colder slag being underlain by hotter matte. Tracer tests in the feed to the smelter and in the feed to the forehearth revealed considerable holdup of material in the plant and confirmed that the forehearth involved small scale turbulence but little large scale mixing. The results indicated that the copper content of slag continuously tapped from the forehearth could be lowered by at least 0.15% if better settling could be achieved and means of attaining this are discussed. As part of the investigation the recovery of copper from spent refractory bricks recycled through the smelter was evaluated. It was found that the recovery was high but it seems likely that the brick material is partly responsible for a build up of solid material in the forehearth.

Jan 1, 1981