Search Documents

Opinions vary widely within the community on what are legitimate environmental social respon- sibilities. The extreme conservationists see the responsibility as the total preservation of the natural environment achieved by opposition to all forms of industrial development that would disturb it. The `growth-at-any-price men' consider it more important to stimulate economic growth, develop new industries, and maximize profit letting the environment take care of itself: within this wide spectrum of concern are the middle-of- the-road men, part of the vast majority, fully aware of the need to compromise to achieve a satisfactory economic growth rate whilst pre- serving to the greatest extent practicable the con- ditions upon which we depend for a balanced self-perpetuating existence. Environmental change is not new. It is the inevitable accompaniment of human activity. Plato wrote in the 5th Century B.C.* of the devastating changes wrought by man and his animals on the ancient world of the Mediter- ranean. Down through the ages rural development to *The Dialogues of Plato: `What are now her moun- tains were lofty, soil-clad hills; her so-called shingle plains of the present day were full of rich soil; and her mountains were heavily afforested-a fact of which there are still visible traces. There are moun- tains in Attica which can now keep nothing but bees, but which were clothed, not so very long ago, with fine trees producing timber suitable for roofing the largest buildings; and roofs hewn from the timber are still in existence. There were also many lofty cultivated trees, while the country produced bound- less pasture for cattle. The annual rainfall was not lost, as it is at present, through being allowed to flow over the denuded surface into the sea, but was received by the country, in all its abundance, into her bosom, where she stored it in her impervious potter's earth and so was able to discharge the drain- age of the heights into the hollows in the form of perennial springs and rivers throughout the land.' provide the necessities of life for expanding populations has required the destruction of vast areas of forest. Industrial activities over the last 200 years have discharged enormous quantities of solid wastes, liquid and gaseous effluents that were environmental pollutants of the worst kind. Urbanization has drawn people, their machines, and industries into vast concentrations aggregat- ing the environmentally bad effects of each to the extent that there is evidence that through thermal pollution these large urban industrial complexes nrp nffPrtina raainnnl rlimnta.c

Jan 1, 1978

By J Cronin, R Burgess-Limerick, T Horberry, L Steiner

"Automation offers the mining industry great potential for improvements in productivity and safety. However, the experience of introducing automation in other industries has been that the full potential of new technology is not always realised. Designers are surprised, for example, to find that automation does not eliminate human errors. Unwanted and unexpected consequences also arise if the introduction of automation fails to consider how people will adapt to the new technology. A focus on the technical aspects of automation is necessary but not sufficient for success. The potential for improvements in productivity and safety promised by automation will only be achieved if the joint cognitive system that emerges from the combination of humans and automation is designed to perform the functions required for system success. This case study describes the human factors issues associated with the introduction of automation generally, and describes a case study of the successful implementation of loader automation at Northparkes mine.Information obtained through a site visit and interviews with operators, safety staff and the project manager revealed the following strategies for successful design and implementation of the automation system: involve the people who will be impacted encourage constant communication between operators and designers provide operators with essential information avoid providing non-essential information provide the operators with flexibility empower operators to take action take advantage of the new possibilities automation provides.CITATION:Burgess-Limerick, R, Horberry, T, Steiner, L and Cronin, J, 2017. Mining automation human-systems integration – CMOC-Northparkes case study, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 93–98 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 16, 2017

By M Dalm

More and more mining companies are becoming aware of the potential benefits of sensor-based ore sorting and process optimisation. This is reflected by a growing number of analysers that are available for drill hole logging, conveyor belt scanning, ore sorting, slurry analysis, etc. These tools all rely on a specific sensor technology that can be used to detect a material property such as colour, density, mineralogy, or chemical elements. However, all sensors have restrictions on the minerals and/or elements that can be detected or inferred. This is caused by the physical mechanisms behind the technology and depends on mineral concentration and compositional heterogeneity of the ore. Since nearly every ore deposit is unique in composition and characterised by different geological features that drive heterogeneity, no one-size-fits-all sensor solution is available. This makes it difficult for mining professionals to find suitable sensing technologies that can help them solve problems and improve processes for their specific ore types.

Sep 1, 2024

By D Macklin, R Hammond, T G. Blenkinsop

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Base metal sulfides at the Currawong volcanic-hosted massive sulfide deposit in the Lachlan fold belt of Victoria, south-east Australia, were formed in the late Silurian, but D2 deformation of the deposit in the Devonian Bindian orogeny was responsible for structural repetition that created the resource. The primary sulfide lenses were stacked by reverse-sense shear zones within a volcano-sedimentary sequence dominated by dacitic intrusions and turbidites. Shear zones were localised along lithological contacts, including the margins of the sulfide lenses. The competent dacitic intrusions did not fold during D2; folding was restricted to the packages of metasedimentary rocks. Overturning occurs within, but not between, the metasedimentary packages. The overall geometry of the deposit is that of a duplex, but the detailed shape does not conform to idealised duplex types, probably because of post-D2 deformation. A significant complicating factor for understanding the deposit, and for resource evaluation, is the dramatic variation in deposit geometry along strike, which may also be due to post-D2 deformation. The present day configuration of the deposit results from constructive thrust repetition of what may have been a single ore lens and destructive along-strike disruption controlled by rheology.CITATION:Blenkinsop, T G, Macklin, D and Hammond, R, 2015. Rheological controls on the geometry of the Currawong volcanic-hosted massive sulfide deposit, Lachlan fold belt, Victoria, south-east Australia, in Proceedings PACRIM 2015 Congress, pp 469–474 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Weyer J

Many existing computer planning programs for the mining industry focus either on big mining enterprises with a high production rate or on smaller operations for high value minerals. Big mining enterprises, like the hardcoal company `Ruhrkohle AG' in Germany have their own R&D departments which develop powerful computer programs for planning purposes, partly in co-operation with mining universities. However, there is a remarkable number of small- scale mining operations which are either not able to buy expensive hard- and software or don't have the skills for the operation of extensive software programs. Partly there is also a trend in using rule of thumb calculations rather than computer programs which need a lot of - partly unavailable - data. For this reason a computer program was developed which does not need expensive hardware and software and which can help the planning engineer in the selection of a limited number of possibilities. Until this time the planning engineer established two or three different cases and calculated the results with a pocket calculator. This could last some hours or even some days. Now he or she can use the computer program with a normal PC to compare the cases. All activities are menu-driven. The basis for all, calculations are fixed and variable costs as well as average performance for special activities. The paper gives an example for a possible planning situation in fluorspar mining (originally this program was developed for the fluorspar enterprise Lengenfeld in Germany). It shows the initial situation, the main structure of the program, the input logic and the results. Benefits, limits and possible extensions of the program are discussed.

Jan 1, 1995

By Kasaneva S

The San Cristobal gold district is located 110 km east of the port of Antofagasta, Chile. It contains the San Cristobal gold mine, where Niugini Mining Ltd. commenced a heap leach operation, with initial reserves of 10.1 million tonnes grading 1.34 g/t An, in December, 1990. The San Cristobal district occurs within an upper Cretaceous-lower Tertiary magmatic arc. The main mineralisation occurs within a northwest trending subvertical zone, 1km long and 70-100 m wide, which contains rhyolite porphyry and minor breccia, and is locally termed the "subvolcanic complex". At the San Cristobal mine, most gold mineralisation occurs in subvertical quartz-pyrite veins which were emplaced in dilational sections of an imbricate fault system. The bulk gold resource comprises four ore shoots which formed where the vein system intersects the subvolcanic complex. Gold-bearing quartz-pyrite veins also occur at separate prospects, the Three Sisters and Sol prospects, west and south of the San Cristobal mine. Hydrothermal alteration consists of potassic and propylitic assemblages related to intrusion of the subvolcanic complex. This alteration is overprinted by a phyllic stage which is associated with the emplacement of the quartz-pyrite veins. The oxide zone is 180 m thick, and contains native gold, electrum, limonite, and manganocarbonates. The underlying hypogene zone contains pyrite with minor chalcopyrite, sphalerite, galena, covellite, bornite, chalcocite, and arsenopyrite. Fluid inclusion studies indicate that the deposit formed at approximately 270¦ C, and the mean salinity of the fluid was 4% NaCl equivalent. These observations enable the San Cristobal deposit to be classed as a porphyry-related, mesothermal quartz-vein system of the low sulphidation type.

Jan 1, 1995

By R West

The Olympic Dam smelter facility processes copper concentrate feed using direct-to-blister smelting technology to support the current site production rate of 225 000 t/a copper. The metallurgical control of the Olympic Dam smelter is largely managed from a single central control room. Control room operation and management is therefore a key function in ensuring safe and reliable operation of the smelter, including identifying and initiating control of abnormal events. As part of a consolidated smelter reliability improvement program, a team consisting of process and control system engineers was formed. The teamÆs charter was to address and resolve the alarm flooding issues being faced by the control room technicians and the lack of an up-to-date base of supporting functional documentation. The project was successfully resourced with WorleyParsons metallurgists, Citect PLC technicians and the on-site technical team. Implementation was conducted over a 12 month period with the goal of achieving best practice alarm levels. The goal was achieved through a systematic process of alarm design review that analysed every configured alarm versus best practice design standards. Innovative concepts such as group-based alarms, first-up interlock displays, graphic only alarming, alarm help and alarm shelving were developed and implemented in conjunction with improved alarm masking. Total configured alarms were reduced from 20 000 to 5000 while the alarm rates were reduced from in excess of 200 alarms per hour per controlling technician to best practice levels of less than 12 alarms per hour per controlling technician. Completion of this program has provided a firm foundation for implementing further control optimisation and was a key activity in supporting sustained smelter reliability levels.

Jan 1, 2005

By A Hatt

This paper presents a case study of characterisation work undertaken at a greenfield exploration project to provide engineering and OH&S inputs for the design of a ventilation system. The paper discusses how comprehensive early characterisation of the ambient surface and underground environment including aspects related to heat, dusts, strata gas, and geologic/mineralogical factors enables incorporation of the right ventilation and non-ventilation controls at a study level to mitigate the risks identified.

Oct 12, 2022

By G Steward

Gravity Leaching of high-grade gravity gold concentrates, such as Knelson Concentrates, with the ACACIA Reactor represents a new generation of concentrate treatment methods. The ACACIA Reactor is a complete packaged plant for the maximising of gold recoveries from gravity gold concentrates. This paper will introduce the process technology and provide process results from the Porgera ACACIA Reactor installation. The advantages of the ACACIA Reactor are many, and justification for installation has been varied. The typical advantages of the process include: increased recovery of gold from the Knelson Concentrate; no return of high-grade table tails, often grading several thousand g/t, into the mill circuit; reduction in tails grades of slow leaching gold; reduction in the requirement for operating staff by the removal of the manual tabling process and replacing with a fully automated treatment system; improved security by removing the tabling step where operating staff come into direct contact with visible gold; improved health and safety, by the removal of the treatment steps for the table concentrate, which often include operators handling corrosive chemicals and the production of sulphur and arsenic compound fumes; and improved metallurgical accounting, by allowing daily head grade calculations. The ACACIA Reactor was developed by Anglogold for Union ReefÆs Gold Plant and has been in production for over two years, and has proven to be a low cost, high recovery, mechanically reliable method for the processing of gold concentrates. Such has been the success of the plant, there are now four full installations of the processing plant, including Anglogold Union ReefÆs, Anglogold Sunrise Dam, PACMIN Carosue Dam and Porgera Joint Venture.

Jan 1, 2002

By K Nesbitt

Draw control at Premier Mine is considered important to avoid conditions of isolated draw, which results in early waste ingress, compaction of the kimberlite ore and loss of ore reserves. The Premier Mine kimberlite pipe is unique in that the pipe is cut at a depth of 400 metres below surface by a 75 metre thick gabbro sill. All cave mining at Premier is below the sill and failure to exercise good draw control could cause early ingress of gabbro waste. Gabbro causes problems in the diamond recovery plant and the amount of gabbro sent to the plant needs to be closely monitored. Fortunately coarse gabbro fragments are easy to recognise in drawpoints. It was anticipated that only 85 per cent of available ore would be drawn from the blocks immediately overlain by the gabbro sill before excessive gabbro waste forced the closure of drawpoints. Data on tons drawn per drawpoint and loaded per LHD as well as the tons tipped per pass is gathered by the vehicle monitoring and control (VMAC) system and information recorded by the load-haul-dump (LHD) drivers. Draw control staff monitor drawpoints on a shift basis and record the occurrence, type and height of hang-ups. Information pertaining to the status of the drawpoint in terms of support, waste and availability is also recorded. A database has been compiled that has been used to analyse the overall pattern of draw control, the frequency of occurrence of different types of hang-ups, secondary blasting efficiencies and drawpoint and LHD productivity. The gabbro sill has provided a unique marker horizon that has allowed the arrival of rock from a level 100 metres above the production level to be recognised. Data shows that ore migrates extensively towards groups of drawpoints that are heavily drawn with many drawpoints more than 100 per cent drawn before gabbro waste was recognised. This indicates that an accurate mixing algorithm is essential for good draw control. Data on tons drawn, drawpoint availability, productivity and the occurrence of various types of hang-ups has allowed better control of the mining operation and provided data for planning future caves. In the BA5 mining block a drawpoint spacing of 22 metres, horizontally across the major apex, has still allowed drawpoints to be pulled to waste with no loss of ore. In the BB1E mining block the drawpoint spacing has been increased to 23 metres and no problems have been experienced to-date. Future initiatives centre on improving the data gathering integrity of the vehicle monitoring and control system and a linear programme that will optimise draw control and productivity.

Jan 1, 2000

By P Hartlieb, M Noeger, M Varelija

Rock bolts are important in underground mining as they provide support to the rock mass around the excavation. They are the most common reinforcement method in mining and civil engineering excavations. The length of the bolts, types and spacing between them can be varied, depending on the reinforcement requirements and the use case (Kolapo, Onifade and Praise, 2022). The rock bolt provides safety and stability for the rock mass in the excavation area and they can be mechanically anchored, grouted, or friction anchored. They normally don’t have a measurement option and there is a possibility that it failed without showing visible signs on the surface, especially in grouted rebar bolts where they can still have some residual strength. Therefore, support functionality can be lost without recognising it. To overcome that, sensors can be installed on all three previously mentioned bolt systems. Intelligent bolts with implemented measuring systems have a function of showing changes and indicating if there is some damage on the bolt. So, it can be said that intelligent rock bolts are regular bolts equipped with additional instruments which are helping us detect potential instabilities inside of the rock mass or malfunction of the bolt itself. Changes in rock mass can be tracked, by measuring rock bolt reaction concerning the excavation response. Rock mass damage and instabilities are therefore measured in terms of rock mass deformation. Moreover, other additional information depending on the type of the sensor device could be collected. Based on such measurements, information about rock mass state can be derived. Different rock bolt types work at different reaction principles. Therefore, limitations on sensor application and information that can be extracted must be considered.

Sep 1, 2024

By J R. Taylor, J A. Muchan, S M. Pape, B S. Davis

Acid and metalliferous drainage (AMD) is routinely derived from waste rock, tailings, pit wall rock, underground mine voids, heap leach pads, ore stockpiles, concentrate stockpiles and even slag piles. In many jurisdictions, there is an assumption that tailings materials represent the highest AMD risk. This is likely due to their highly sulfidic and ultra-fine grained nature, and the fact that they occur in large tonnage, partially unsaturated deposits. These characteristics are not unreasonably associated with reactive and therefore highly polluting mine waste materials. Interestingly, however, the high sulfide content and highly reactive nature of tailings achieves the rapid consumption of oxygen in tailings pore spaces. This oxygen depletion can limit or halt sulfide oxidation throughout much of the tailings pile. Oxygen can only be resupplied to the tailings via atmospheric exchange at the air-tailings interface. The grain size of most tailings materials limits this resupply to a diffusion related process that only affects the uppermost 100–2000 mm. Hence sulfide oxidation in tailings can be inherently self-limiting. Unfortunately, the same cannot be concluded for waste rock materials.Using a unique site assessment strategy that focuses on quantifying acidity fluxes from various domains at a mine site, it has become increasingly evident that sulfidic waste rock produces the majority (typically 60–80 per cent) of the soluble acid and metalliferous pollution at most active and decommissioned sulfide-bearing mine sites. Whether sulfidic waste rock is disposed in engineered above ground facilities, backfilled into pits or even underground voids, it remains the primary source of pollutants for decades to centuries.Conventional end-dumping waste rock practices result in angle-of-repose pathways for air and water, and these internal fabrics exacerbate sulfide oxidation (ie pollution generation) and discharge from waste rock materials. The primary aim of many cover systems is to retard the access of air and water to these conduits. Recent thinking is that more emphasis needs to be directed at strategic waste rock pile construction practices, and less reliance placed on thin soil cover systems to prevent AMD.Waste rock pile construction approaches that minimise porosity and permeability but raise the retained moisture content and enhance water residence times have the potential to lower sulfide oxidation rates and thereby improve water quality outcomes. For example, innovative base-up, layered and compacted (BULC) waste rock piles have the potential to avoid or minimise the generation of AMD, supersede the need for treatment and facilitate successful closure and relinquishment across the mining sector (Figure 1).CITATION:Taylor, J R, Pape, S M, Davis, B S and Muchan, J A, 2016. Waste rock pile construction to lower closure and relinquishment costs, in Proceedings Life-of-Mine 2016 Conference, pp 97–99 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By H S. Pescini

A material aim when feeding ore blends into a processing facility is to reduce the variability of the properties of the feed material and to maximise the output, or throughput. At the Mining Geology conference of 2019, we presented a paper on optimal blending of coking coal given geological variability. The paper introduced integer-programming techniques to both maximise value and minimise feed or product variability. We discussed an application where the geological uncertainty is characterised using a normal distribution and exact solutions are readily obtainable using second order conic constraints in the mathematical model. Geological uncertainty is not always normally distributed, many properties will be characterised as log normal or some other skewed distribution. For example, copper can be some form of lognormal and Fe in Iron ore has a left skewed distribution. In this paper, we discuss some distribution free techniques to optimise the blends of plant feed or output given a quantified geological uncertainty. We discuss the sample average approximation method and how to set-up and apply the method to an ore blending problem. Evaluating a case study demonstrates that the explicit use of non-normally distributed geological uncertainty can better optimise feed into an ore processing facility and potentially add significant value. The approach is equally applicable to all mining and processing operations that blend material into a processing facility or directly into a saleable product.

Mar 22, 2022

By S Szylkarski, D N. Graham

In mining, water management is an operational necessity, requiring planning and detailed engineering, as well as risk assessment. Yet, the hydrology of streams and aquifers typically extends well beyond the boundaries of mine operations and intersect with environmental and social values. Mine managers often plan, design and assess the impact of water management activities (such as dewatering, excess water disposal and flood management) with a mine site or process specific focus. The challenge is that the impacts are spatial, long-term and complex – and may be cumulative across multiple mine sites. Further, there is usually little consideration of the feedbacks and interactions between surface water, groundwater and catchment hydrology. Failure to understand these processes can lead to poor decisions and increased costs. This presentation outlines an approach to simulating integrated hydrology in mining catchments that addresses the shortcomings of traditional modelling techniques.CITATION:Graham, D N and Szylkarski, S, 2016. Simulating integrated hydrology in mining catchments from planning to closure, in Proceedings Life-of-Mine 2016 Conference, pp 101–105 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

In line with mining operations throughout Australia, Western Mining Corporation Limiter' is striving to increase productivity by intro-ducing mechanized mining techniques wherever possible. Kambalda Nickel Operations' (K.N.O.) largest operating nickel mine, Long Shaft, is currently introducing mechanized cut and fill methods which must provide flexibility to cater for an orebody that variesconsiderably in width, both along the strike and up dip.This has resulted in modifications to the previous approach to primary level develop-ment, and intermediate stope development, and in the type of development and production equipment being employed. Electric-hydraulic diesel jumbos and diesel loaders have now been mated with conventional rail equipment and production airtrack machines are being utilized.The transition to mechanized methods is in its preliminary phase and is being monitored closely to ensure any productivity gains are not offset by a substantial drop in mine grade. The precise method ofmechanized mining has not been finalized and selective methods will be used, according to the ore width and ground conditions, which vary throughout the mine.

Jan 1, 1985

By S Williams, N McBride

The aim of these analyses was to utilise the latest available production information for the Wandoo operation to determine the optimal blasting parameters, costing information and predicted results (fragmentation, muckpile shape and vibration). Much of the data used as input was made available from the information gathered during the excavation of the test pits during 1995. As with any æplanning stageÆ analyses, many assumptions were required to fill gaps in the available data. The calibration of computer blasting models was conducted using data from the last of the test pit blasts (this blast was carried out in material that closely resembled rock expected to constitute the bulk of the base case design pit). This calibration was refined using observation and experience based judgements to extend the accuracy of the predictions as far as possible. All the simulations were performed assuming that the blastholes will be wet (as instructed by BGM). This has consequently determined that the appropriate explosive for the simulations and the actual blasting will be a pumped emulsion/ANFO blend. The following blast design parameters were derived by determining a likely range of powder factor (from other similar scale gold mines) with a median value of 0.62 kg/m 3 being the powder factor arrived at through the field optimisation process conducted during the test pit excavation. The total swell/displacement percentage (volume after blast/volume before blast) largely determines the diggability of a well fragmented muckpile. Consequently where fragmentation is good any reduction of total swell will probably reduce diggabilty. Any reduction of diggability can and should be traded off against increased gold recovery. In most gold mines, diggabilty will be substantially compromised at the balance which produces the most profit. When these considerations are combined with the cost to drill and blast material, processing costs and the achievement of æacceptableÆ diggibility, the analysis becomes extremely complex and qualitative. Many trends are evident including:the relationship between powder factor (for each blast design) and maximum forward displacement (throw), see Figure 1; and the relationship between powder factor (for each blast design) and drill and blast cost per BCM, see Figure 2. The following blast designs are matched to each of three ore-tonnage alternatives (as supplied by BGM) (Table 1). They are all based on powder factor of 0.62 kg/BCM and are considered optimum from a mining æpoint of viewÆ. The costing of each design includes drilling, explosives and labour cost to load, stem and tie-in holes. Using the available rock data and relying heavily on the wall exposures in the test pit(s), it is the opinion of the author that between 20 per cent to 40 per cent of the final walls excavated in the Wandoo pit would be likely to have the angle between the dominant foliation and the wall plane that is well suited to presplitting and be cost-effectively served by presplit technique. The drilling cost for 125 mm blasthole is about $11.40 per drilled metre and the cost of 40 mm presplit explosive is about $140 per 25 kg (17 metre) case. This implies that the cost to drill and blast presplit on the above parameters would be about $10.90 per square metre of presplit face. The remaining wall area would be most cost-effectively delineated using modified production blasting techniques. This requires the use of modified parameters such as smaller hole diameters, smaller spacing/ burden, higher powder factor, free face firing, less rows per blast and longer delays. These altered blast parameters would usually be applied uniformly across the entire blast fired adjacent to the wall and this ætrimÆ blast would relieve burden away from the wall, into the pit. In simplest terms, this method relies upon maximised burden relief to minimise blast energy applied to the wall. It is only applicable where the material to be blasted is waste since the throw achieved is inconsistent with ore dilution control. The largest charge weight per hole for these analyses is 360 kg and the nearest domestic structure to the proposed Wandoo pit is about 6100 metres distant. From these parameters and assuming a worst case example of rock controlled site factor, the predicted ground vibration is 0.5 mm/sec that is about five per cent of the lower limit set down in AS 2187 part two (1993). This suggests that for the current location of neighbours, ground vibration will not be an issue for the Wandoo operation.

Jan 1, 1999

By Ricketts N. J, Smith G. D J

A hydrometallurgical process was developed for recovery of copper from copper-lead matte formed as an intermediate product at the BHAS lead smelter at Port Pirie. A plant utilizing this process was commissioned in 1984. The leach step involves oxidation of the copper-lead matte in an oxygenated acidic chloride-sulphate leachant. The results of laboratory scale testwork from which the chemistry of leaching was deduced, are presented in this paper. The rate of recovery of copper to solution from copper-lead matte depends largely_on the availability of oxygen to the sulphide surface. The optimum leach temperature is approximately 85¦C. Free acid must be supplied according to the stoichiometry of the leach reaction: Cu1.91 S + PbS + 2.91 H2SO4 + 1.455 02 = 1.91 Cu2+ + 1.91 SOj- + PbSO4(s) + 2.91 H2O + S¦ The grind size of the matte is of minor significance. Chloride concentration in leachant should be at or above a minimum of 10.0 g/l. Chloride acts to complex cuprous ions formed during leaching.

Jan 1, 1987

The Queensland Magnesia Project is based on a unique cryptocrystalline nodular magnesite orebody which required an innovative approach to process design in order to economically exploit the characteristics of the ore and produce a marketable range of high quality refractory magnesias for a declining world market. High quality natural refractory magnesia must have an MgO content in excess of 95 per cent with a very strictly controlled content and ratio of residual impurities such as calcium, silica and iron. The natural products compete with magnesias derived by chemical extraction from sea water or brines which exhibit very high purity but often lack other characteristics which are of value to refractory brick makers. Since start up in late-1991 QMAG has achieved a remarkable market penetration for both its deadburned and electrofused products with sales for the 1993/94 financial year representing 92 per cent of deadburned capacity and 138 per cent of original electrofused capacity respectively, all at a time when the world steel industry has been in recession.

Jan 1, 1995

By Richards JR, Herbert HK

A basic question in preparing this review was how to define sulphur mineral occurrences as being associated with the Pacific Rim. This question will be reconsidered later. The isotope composition of sulphur- containing minerals may be considered in terms of two primary sources - 1. deep- seated sulphur, devoid of crustal contam- ination with a 634S value near 00/0o and 2. oceanic sulphate which fluctuated in value between +10 and +300/00 over geological time (Claypool et al., 1980). However, minerals have seldom been directly derived from these primary sources as even evaporites have been dissolved and reprecipitated. The marine source is differentiated biochemically and isotopically in recent sediments where sulphide from bacterial sulphate reduction may be significantly depleted in 31S. The question of chemical interaction of ascend- ing magma with upper crustal rocks has become one of degree rather than whether or not it occurs. Mineral deposition is considered increasingly in terms of mixing of fluids and their chemical reactions with rocks rather than direct precipitation from magmas or hydrothermal fluids derived from them.

Jan 1, 1987

Accident prevention in industry is a task as important to the ultimate result of an undertaking as efficient machines, good tools or trained operatives. In fact, like many qther phases of industry today, "Accident Prevention" or "Safety Organisation" has developed in this century, to a degree that is now acknowledged as an integral part of industrial thought and planning. This has not always been the case, as the following snap-shot picture of the past illustrates.The Broken Hill Proprietary Company recently celebrated at Whyalla the Jubilee of the opening of the Iron Knob Tramway. On that occasion a dinner was tendered to the pioneers, and in talking to the Writer of the early days one of the old gentlemen present could not refrain from recounting some of the accidents he had seen or experienced.Several such incidents were recounted at length, after each, the old fellow would say, "An' there weren't no safety officers or compensation in them days".The Broken Hill Proprietary Company Limited was a pioneer of safety in Australian industry and considerable success has followed its activity in this connection; the accident rate of the steel industry now compares satisfactorily with that of any other industrial undertaking. A measure of 'the success of the safety organisation, is, that in recent years, despite extensive construction programmes at various centres, and despite a heavy labour turnover, a decreasing accident rate has been maintained. This success, in the Writer's opinion, arises from the fact that by its early attention to plant protection, the introduction of safety standards and further through the interest and energy of departmental superintendents and foremen, the...

Jan 1, 1951