Search Documents

By Hang G, Hongtian X

In this paper, it is briefly introduced that China's Ordovician limestone confined-water menaces coal mining and Ordovician water is prevented and cured to secure the safety of coal mining. The theory of "Down-Three-Zones" is presented on the basis of research and practice in recent ten years. The concept of "Down-Three-Zones" of floor water-eruption is described clearly. Finally, the principle and method of applying the theory of "Down-Three-Zones" are discussed. 1. An Introduction of Damage: China is rich in coal resources. The conditions of coal field geology are quite complicated. There is an area of two million square kilometre of Karst limestone in nine million six thousand square kilometres of territory. The resources of underground water are rather plentiful, but this menaces coal exploration. Sixty percent of coal mines in China are damaged by limestone confined-water in different scales, particularly coal mines located the Carboniferous-Permian coal fields of the Ordovician limestone distribution area of Northern China. Because there is the 500-800 metre thickness of Ordovocian limestone and the well developed Karst containsl plentiful water, Karst water can have more than 100 Kg/cm pressure. Limestone aquifers have only distances of several metres or several decade metres to coal seam, Karst water can enter the aquituge and even the coal seam, large eruptions often occur. For example, a mine of 3 million ton production capacity had an eruption of 2053 cubic metres per minute. This is the largest confined-water eruption which has brought enormous economic damage and threatened the safe production of coal mining. Therefore, the prevention and cure of Ordovician water has immense advantage to the development of the coal industry. There are several decades experience in the prevention of Ordovician water-eruption in China. The prevention of Ordovician water-eruption has two kinds of plans. 1) dewatering and depression: it refers to dewatering of aquifers as roofs of seam and depression of aquifers as floors of seam in mining areas. 2) comprehensive prevention under the condition of having water pressure in aquiters. Due to enormous water, electricity, equipment and lots of other factors, the former isn't used extensively, the latter tits to China's actual conditions and is used widely. So-called comprehensive prevention under the condition of

Jan 1, 1988

Drilling underground can be a hazardous undertaking in many circumstances. Raiseboring and boxhole boring underground could form an integral part of the block caving production methodology and getting the right mix of technical capability, ergonomics and economical viability has been the goal of many machine manufacturers. With the introduction of the Terratec Universal Boring Machine concept, flexibility of raiseboring, downreaming and boxholing has been enhanced by the introduction of a single machine that will perform all three processes. In addition to its technical flexibility, additional safety features have been introduced that will eliminate many sources of injury by mechanising most of the operational procedures. Together with the one-man remote operation, this machine design addresses and solves many of the safety issues. This paper outlines the machine concept, details its safety features and shows the techno-economic advantages for use in the block caving environment. Block caving is a distinct caving method applied mostly to large massive orebodies because of the inherent low costs and high production capabilities. Areas of sufficient size are mined by undercutting so that the mass above will cave naturally. Extraction of the caved ore at the bottom of the ore column causes the caving action to continue upward until all of the ore above the undercut level is broken into sizes suitable for handling (Figure 1).

Jan 1, 2000

By D Kilkenny, D Nardini, P Kline

This paper is a case study highlighting learnings and success in two areas challenging underground miners: change management and collaboration. It examines the implementation process of a new automated loading system in the bulk stoping area of Telfer Mine in Western Australia, controlling multiple load haul dump machines. Here, the new technology has brought together different functions and different companies to deliver a well performing automation system in a changing and challenging mining environment. The introduction of a new and different technology on site has driven collaboration between all stakeholders to break down the traditional barriers to achieve the sustained performance required. Historically, different teams have operated within silos and not always aligned to deliver a ‘best for project’ solution. Technical teams focus on the mine design, maintenance teams focus on reliability and operations execute the plan. Mining contractors focus on productivity and cost. Manufacturers focus on supply of goods and service. Optimising each silo individually is not guaranteed to provide an optimal mining solution. Involving elements from each team as seen at Telfer, has resulted in an optimal mining solution for the automated loading system. A change of focus from the technical teams to include automation parameters in the mine design; operability and maintainability built into the system design allowing for collective ownership and responsibility resulting in a more resilient solution. The implementation of the new technology was not only a technical change but more importantly, successful management of change. Elements of successful change management such as communication, vision, leadership and planning, are essential to harness a trusting site culture which is responsive to new technology. Learnings and challenges from this change process will also be discussed with the intent to improve the success rate and timelines of technology implementations in the future.

Mar 15, 2021

By R G. Reddy, Z Zhang

Viscosities of CaO-aluminosilicate ternary melts were estimated using a structure-based model. The model considers depolymerisation effects and related breakdown of the silicate network structure on the addition of metal oxides to the melts. The predicted values are in good agreement with the experimental values over the whole temperature and composition range.

Aug 21, 2024

The Olympic Dam copper-uranium-gold-silver deposit, located 520 km NNW of Adelaide, S.A. was discovered by Western Mining Corporation Ltd in 1975, and is now being developed as a joint venture between WMC (5107o) and the BP Group (4907o). The discovery of this deposit resulted from the application of a conceptual model for the formation of sediment-hosted copper deposits. This model postulated that the oxidation of basaltic rocks could release significant amounts of copper into solution and that, under favourable conditions, these solutions might pass upwards along faults, and the copper be precipitated in reduced- facies sediments higher in the sequence. The Stuart Shelf province was chosen for exploration because geological interpretation suggested the presence of suitable basal- tic source rocks at depth, and favourable host sedimentary rocks in the overlying sequence. The Olympic Dam site was selected for drill-testing because of the presence of coincident gravity and aeromagnetic anomalies suggesting the presence of basalts and/or mineralisation at depth. This site also had a favourable tectonic signature, indicating the presence of deep crustal structures which might have allowed fluid migration.

Jan 1, 1988

By O Bøckman, E Thisted, K H. Esbensen, U Thisted

Process industry measurement systems, once installed, are often interpreted as static black boxes delivering correct values as long as not proven otherwise. After first implementation and set-up with a distinct sampling frequency, they often run ‘forever’ without checking if this frequency is still appropriate with respect to changed raw materials characteristics, different process conditions or changed customer specifications. Failure detection is based on operator experience and skills (often close to an art form) and/or from control measurements of reference samples. This may well be too late for many industrial process contexts. An appropriate sampling frequency is a critical success factor for valid monitoring and control.Based on the methodology of variographic analysis we here illustrate how to design/re-design/optimise an industrial measurement system in terms of sampling frequency, discretisation and accuracy based on customer specifications. We also show how variographics can be used to monitor for deviations. We use experience from process industry to show how these methods can be used not only for product characterisation, but also for monitoring input factors, process indicators and measurement of these. The information hidden in the vast amounts of data that is continuously created in modern process industries can be utilised to cut costs in the measurement activities and at the same time contribute to early error detection. We illustrate by case examples from production processes at a nickel refinery, supporting the Lean and Six Sigma methodology. This will provide a standard operating procedure for monitoring the stability of measurement systems, and provide a basis with which to discuss how a variographic approach can be integrated with the Lean and Six Sigma approach as an online tool to map, characterise and validate measurement systems and thus avoid more cumbersome measurement system analysis in full detail.CITATION:Thisted, E, Thisted, U, Bøckman, O and Esbensen, K H, 2017. Variographic case study for designing, monitoring and optimising industrial measurement systems – the missing link in Lean and Six Sigma, in Proceedings Eighth World Conference on Sampling and Blending , pp 359–366 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By M A. Noppé

"Investors and other stakeholders assessing the risk, opportunity and relative value associated with a resource project need to appreciate the project in its correct context. Errors, omissions, biased reporting or conflicting information in project reporting may lead to a misinterpretation of technical and financial results, resulting in biased estimates or assumptions on project value.This paper provides a simple ‘Resource Project Framework’ for presenting a project’s status that may be readily benchmarked against other similar projects and to illustrate the stages required to advance the project outcomes to higher levels of certainty. The framework draws on definitions and guidelines readily available in various resource industry reporting codes and public company reporting requirements.The framework assesses three key areas for placing a resource project in its correct relative context, namely:the project development stagethe confidence in the Exploration Results, Mineral Resources and/or Ore Reservesthe level of accuracy, precision and confidence in the technical and economic studies supporting the reported results or options for the project.The application of the Resource Project Framework is illustrated using two project examples, one from publicly reported company project releases and the other for two development projects.CITATION:Noppé, M A, 2016. A framework for presenting and benchmarking resource projects, in Proceedings Project Evaluation 2016, pp 260–274 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By P Valenzuela

Joint mapping is a fundamental input for rock mass characterisation and slope stability analysis. The usual way to do it is using a compass in the field or digitising structures on a screen, with a software package.In this paper a method to identify and map joints automatically along a rock face is presented; it is called the Concentric Shells (CS) algorithm. The method scans a point cloud sequentially, tests if selected points are ‘true pivots’ within an inner shell, and then it searches for points inside a wider sphere (outer shell).The algorithm, developed by the author, was applied in real data. It reproduces the main features obtained from conventional (compass) and digital mapping (software package). Execution times are approximately 45 seconds for two point sets holding of 3.1 million points. Obtaining the same results via digital mapping takes approximately 3–4 working days.Key advantages of this method are: significant time reductions; elimination of mapping bias; and the ability to manage very large data sets (>2 million points) without the need of scanning the cloud on the screen. These advantages make this method an attractive tool for engineers and geologists wanting to increase productivity.CITATION:Valenzuela, P, 2017. Automated joint mapping using the concentric shells algorithm, in Proceedings Tenth International Mining Geology Conference 2017, pp 257–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

An Integrated Geology-Mine-Plant and Eco-Efficiency Simulator for Anglo Platinum's Evaluation and Operational Improvement Initiatives

Sep 13, 2010

By M Jacobs

This abstract discusses a heap leach copper mine that was failing to perform and as a result was not meeting targeted production. The mine had numerous technical challenges including: high water inflows, low levels of geotechnical monitoring, performance issues with mining, resource model and grade control reconciliation issues, and unexplained low levels of performance from the heap leaching operations. A team from various organisations with specialist skill sets including: a forensic accountant, the owner’s representative and a mining engineer, was arranged to visit the site. The task was to investigate the situation and determine what could be done to turn the performance of the mine around. After an initial assessment in late 2018, efforts were directed to better understanding the operations and improving the performance of the site through preventative management. A key part included the creation of production forecasts that could be achieved that would help restore confidence in the operations. Uncertainty in the mine achieving production forecasts and the performance of the heap leaching operations were contributing to the decline of the operations. Investigations uncovered the fact that while the resource model could reliably predict total copper, a lack of sequential leach data meant the accurate prediction of soluble and insoluble copper species, both important for heap leaching, was difficult to do with any degree of certainty. The crushing and mining contractors also appeared to have suffered somewhat from a lack of management by the owner’s team and performance had affected the production of copper. Collaboration and management were used by the team to understand and stabilise the operations. Ongoing collaborative efforts by the management team, site personnel and contractors resulted in a positive outcome for the owners and their mine – and could at yours.

Jun 22, 2022

By W Mahoney, F Clement, E Saraiva

Prefabricated waterproofing sheet membranes are extremely complicated to install in underground sections with complex geometries and, despite being already subjected to quality tests in the factory, the installed membrane often exhibits leakages due to different reasons. Main sources of leaks are the required high amount of welding seams and damages caused during installation of reinforcement, as well as overstretching and poorly installed secondary concrete linings. Also the design of the tunnel lining is strongly influenced and limited by the use of prefabricated waterproofing sheet membranes. The use of sprayed waterproofing membranes for more than a decade has contributed to durability and serviceability, as well as to increasing sustainability of tunnel linings. The presented sprayed waterproofing membrane MasterSeal 345 is an advantageous alternative to prefabricated waterproofing sheet membranes under typical tunnelling conditions, especially in geometrically complex areas, such as in lay-by niches, cross passages and crossover caverns, where installation of conventional waterproofing membranes is inherently difficult, and locating leaks is challenging. This membrane has been successfully used in underground projects with different waterproofing design concepts and under diverse hydro-geological and environmental conditions for over a decade. It provides tunnel designers with different options and optimisation for the design of the tunnel concrete lining. Additional advantages to owners, contractors and designers from the use of the sprayed membrane include flexibility in the design, increased productivity and flexibility in working programming, as well as improved logistics, resulting in significant program and cost savings and reduced long-term maintenance costs. This paper describes the key features of this sprayed waterproofing membrane, its application range and limitations, the waterproofing concept, design options and related benefits. Further, guidance for membrane application and quality control and a summary of two recent project references in the United Kingdom and in Switzerland are provided.CITATION:Saraiva, E, Clement, F and Mahoney, W, 2014. The use of sprayable waterproofing membranes in underground structures – concept, design options, benefits and limitations, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 323–332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By S H. Algie, D P. Taplin, S G. Doig

"Suboptimal performance of clusters of hydrocyclones (cyclones), relative to the performance of the individual cyclones that comprise the cluster, is a common phenomenon. The primary cause is well known: uneven distribution of the slurry feed into the individual cyclones. The direct result of uneven distribution is that each cyclone in a cluster performs somewhat differently. Hence, some, if not all, of them do not work at their intended operating points, and the classification is not as sharp as intended. The impact on grade, recovery and milling efficiency will vary depending on the duty of the processing circuit, but the most immediately apparent consequence of uneven distribution is a difference in wear rates in the individual cyclones; this exacerbates the problems of unequal performance of the individual cyclones. In severe cases, and as differential wear proceeds, flows from the individual cyclones may become visibly different. Uneven distribution, once the phenomenon was identified, was seen to be a significant issue in the high-solids hydrocyclone cluster in the ball mill recycle section of Evolution Mining’s Edna May Operation (EMO, Westonia, Western Australia) gold processing plant. In 2012, a FloCEP® hydrocyclone feed distributor system was installed to alleviate the problem. Over the next four years of operation, this innovation has proven its value in the metallurgical and maintenance areas. Individual cyclones now wear at the same rate, greatly reducing the need for operator intervention, as well as increasing overall plant availability through minimising unplanned maintenance. The costs of the installation can be justified by savings in maintenance alone, though the greatest value, as is described in this paper, is in allowing the plant to produce consistently closer to its operational design limits. The FloCEP® system is a low maintenance, readily installed retrofit, based on two patented devices that are combined with complementary proprietary design methodology allowing customisation for specific flow rates and slurry particle properties. Together, these devices produce and distribute a pseudo-homogenous slurry flow without moving parts.Citation:Taplin, D P, Doig, S G and Algie, S H, 2016. Experience with FloCEP® Slurry Flow Conditioning at Evolution Mining's Edna May Operation, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 251–260 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

Development of a global failure criterion for rocks has been a desired goal in rock mechanics. Due to variations in factors affecting rock specifications and their mechanical properties, proposing a single failure criterion suitable for all rock types has proven to be unachievable. The theoretical failure criteria do not fit the real data correctly. Amongst empirical criteria, the Bieniawski criterion has demonstrated an acceptable agreement with laboratory generated data. It has been experienced that the ability to estimate rock strength via the modified form of this criterion is significantly improved. Based on the modified Bieniawski criterion and using VB.net, an associated Microsoft Windows program named 'RAMOCE' has been developed. The inputs of RAMOCE can be triaxial compressive strength data, Bieniawski parameters of a specific rock or the type of given rock. Based on input data, potential outputs of the program are Bieniawski's rock parameters, sensitivity analysis of the effective parameters, rock failure prediction and defining the type of given rock.

Nov 25, 2010

By A Densten, C Gimber

Surface water management and drainage is a key aspect of mine rehabilitation and closure planning. In the authors’ experience, drainage related problems are amongst the most common forms of failure in mined landscapes. The appropriate design of surface water infrastructure is therefore a key focus of practitioners. While there is currently a trend towards distributed drainage networks and avoiding hard engineered structures, in many situations (especially for existing landforms) engineered drainage structures cannot be avoided. CITATION:Gimber, C and Densten, A, 2018. A risk-based approach to drainage design standard selection for mine rehabilitation and relinquishment, in Proceedings Life-of-Mine 2018, pp 116–118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By Y S. Zhang

Natural phenomena and human engineering construction activities had great influence on the geosciences space. Natural disasters, particularly mine disaster and other geological disasters happened frequently, which brought great losses both in people’s lives and economics, therefore, to explore the essential causes and mechanisms of disaster by some useful approaches is the most important step in mine disaster prevention. In a variety of methods, building an aground-underground seamlessly integrated model, and then analysing the formation and development mechanism of mining disaster based on this model is a useful way. In this paper, we studied an aground-underground seamlessly Integrated modelling method, and correspondingly given an aground-underground seamlessly integrated 3D spatial model, CSG+CD-TIN+GTP-TTS, by which we can carry out analysis of surface subsidence and underground laneway distortion efficiently, finally preliminary applications verified the effectiveness of this method.

Nov 22, 2011

By R C. Morris

Two major types of economic secondary iron ores occur in the banded iron formation (BIF)-rich Hamersley Province of the Pilbara, Western Australia:dominant BIF-hosted bedded iron deposits (BID)detrital ore deposits (DID sensu lato), which are mainly hosted in the three province-wide Cenozoic sequences that include coeval non-ore sediments and comprise:a. the major Miocene, fluvial channel iron deposits (CID)b. the lesser Eocene and Pliocene detrital iron deposits (DID sensu stricto).Striking differences exist between the massive CID resources and the much smaller underlying and overlying DID. CID are essentially riverine alluvial ooidal rocks with abundant small fossil wood fragments and variable iron peloids, but with only extremely rare recognisable lithic remnants. The original matrix is typically ramifying layered goethite. Eocene DID are mainly alluvial with minor pisoids, whereas Pliocene–Quaternary DID are dominantly coarse colluvial gravels, both derived from and largely retaining the original textures of BID, hard cap or variably ferruginised surface BIF. The colluvial DID matrix is typically ferroan-aluminous soil, resulting in canga where replaced by goethite, which may be dehydrated to hematite by exposure. The Cenozoic deposits occur in two dominant geomorphological environments: the southern Marra Mamba to Brockman Iron Formation strike valleys containing all three Cenozoic sequences and the much later northern Brockman Iron Formation plateau valleys that include only the Miocene and Pliocene sequences. The Cenozoic detritals formed in different climatic regimes, with an extended dry period forming a prominent province-wide dehydrated carapace on the Eocene DID. The Miocene ‘optimum’ followed with its thick scrub-covered deep regolith that produced the fossil wood-rich CID and was succeeded by the arid cool period of the Oakover limestone/calcrete. A major renewal of exposure and erosion in the Pliocene resulted in the extensive iron gravels of the Pliocene–Quaternary.CITATION:Morris, R C, 2015. The Cenozoic detrital iron deposits of the Hamersley Province of Western Australia – a tribute to Mal Kneeshaw, in Proceedings Iron Ore 2015, pp 319–326 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By S Hille, J Karageorgos

With the increased variability of todayÆs large-scale mining operations, consistent flotation performance is important to improving and sustaining overall recovery through the circuit. The Newcrest Telfer Mine has implemented advanced process control technology to obtain stable level operation and consistent mass pull in the copper rougher and scavenger flotation circuits. The final result has been an overall reduction in variability, which impacts on both copper and gold recovery. This paper describes the methodology and implementation of the improvements in control at the Newcrest Telfer Mine as being an essential part of the business for minerals processing.

Jan 1, 2007

Dust emissions from mining, material processing and ship loading operations (fugitive dust sources) are an environmental issue of increasing concern to both government regulators and the community. The main concerns relate to potential amenity, health and environmental impacts from the emissions. Therefore it is imperative that mining/ processing operations, as part of their overall environmental management, reduce fugitive particulate emissions to as low a level as is practicably possible. This technical paper outlines the mechanisms that lead to fugitive particulate emissions, the importance of understanding the exact cause of fugitive emissions, monitoring methods that can be used to quantify the emissions from specific sources, the use of atmospheric dispersion modelling in dust management and innovative dust management strategies including predictive meteorology and proactive management.

Jan 1, 2009

By T J. Napier-Munn, T Perkins

The JK Drop Weight test was developed at the Julius Kruttschnitt Mineral Research Centre (JKMRC) in the early 1990s as a means of characterising ore for the purposes of AG/SAG mill and crusher modelling. It has since been used extensively worldwide in the minerals industry as a key ore characterisation test which produces parameters which are used in comminution circuit design and optimisation. The test generates three parameters which are used in the AG/SAG mill model of the JKSimMet software. The resistance of the ore to high energy (impact) breakage is quantified with the A and b parameters. The oreÆs resistance to low energy (abrasion) breakage is measured using the ta parameter. The accuracy and precision of the results of the JK drop weight test are of great importance given that the parameters are key inputs in the design of such capital intensive items as SAG mills. Plant optimisation exercises also rely on the accuracy of the parameters to assist with improving the performance of an existing circuit. A thorough analysis of the accuracy and precision of the parameters generated by the JK drop weight test has now been undertaken by JKTech Pty Ltd (JKTech). An experimental program was designed using statistical methods to plan a hierarchical set of 24 drop weight tests on homogeneous material. Each stage of the test was identified and incorporated into the experimental design so that the contribution to the overall error of each stage could be quantified, including the effect of operator. The data were analysed by nested analysis of variance. An overall analysis of the A, b and ta parameters generated from the test program has now quantified the variance of these parameters more thoroughly than ever before. Using the results for the impact parameters, an analysis has been carried out to investigate the effect of these variances on final SAG mill comminution circuit design. The results will also be used to refine the comparative testing procedures currently in use by licensees worldwide.

Jan 1, 2008

Self Advancing or "Poweredtt supports are a successful means of supporting roof and designs have reached the stage where adequate support capa- bility is available for all conditions. Some designs have resulted in equipment being too difficult to transport underground and too complex to maintain. Current trends are reducing those problems and simplicity in hydraulic systems is now the keynote of both supplier and user. There is a good possibility that the "Shield-Chock" support will be the universal design of the future. So-called t'shortwall supports" have been developed to the point where they can be applied with a high degree of confidence to conditions of great variety. Develop- ments by manufacturers and practices of users related to maintenance should result in consistent achievement of designed performance.

Jan 1, 1974