Search Documents

By D Chalmers, C C. Harb

The detection and control of gas levels in mining is a continuing challenge for the industry. Standard detectors have many problems that could be overcome with laser based spectroscopic instruments, but to date these systems have not been suitable for mining conditions. This paper reports the development of a new digital data extraction scheme to modernise traditional cavity ring down spectroscopy (CRDS). CRDS is a direct cavity enhanced laser based absorption technique, which is used to allow the identification of an unknown substance by their molecular fingerprint; this unknown substance is identified by analysing the ring downtime of the light exiting the optical cavity. Traditional CRDS has many issues when analysing substances in hostile environments, or when multiple species may be present. This presents an alternative approach, called real-time CRDS (rtCRDS) that has the potential to overcome many of these issues and produces systems that could be used in the mining industry. The system utilises newly developed widely tuning quantum cascade lasers combined with improved optical cavities and novel digital data extraction to produce spectra over a 1500 nm range in a few seconds. The ring downtime measurements produced are accurate and have high sensitivity and maximum signal to noise ratio. This paper discusses the technique, illustrating the advantages compared to traditional systems and show real-time spectra for a set of molecules of interest to the mining industry. This paper also provided an analogy between this approach and that used in digital communications systems, and shows that this scheme is ideally suited to provide a network of sensors in hostile environments.CITATION:Harb, C C and Chalmers, D, 2015. Real-time methane detection – modern digital laser spectroscopy for hostile environments, in Proceedings The Australian Mine Ventilation Conference, pp 161–166 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By MáAndrusiewicz, M M. Hilden, M S. Powell, P D. Kay, B Foggiatto

Circuits with unconventional and potentially more complex designs are predicted to become more common in the future as plant designers and operators look to process ores more efficiently. Ideas have been presented on how circuit design may be changed to utilise todayÆs technology to address tomorrowÆs challenges (Powell and Bye, 2009; Powell, Benzer and Mainza, 2011a). High pressure grinding roll (HPGR) installations in various configurations; application of preconcentration plants eg sorting, magnetic or gravity separation; and preweakening devices eg microwave processing; are all examples of technologies having the potential to deliver a significant reduction in comminution energy for ores amenable to these processes. Not only will future novel circuits contain equipment for which models are not as well developed (if at all), many will likely require the ability to respond to variations in feed, and interact with geometallurgical models requiring process adjustments when the ore characteristics change.In order to confidently simulate more complex circuits and accommodate variations in feed type, a significant advancement in modelling and simulation capability is required. This includes dealing with multiple components in the feed, accommodating different competencies of ore, utilising physical separation opportunities and tracking the grade reporting along the different potential processing routes. Developing the means to simulate complex circuits has been a key priority of a collaborative group of comminution researchers working to solve these challenges.Simulations are presented utilising a new configurable simulation interface called the model developers kit (MDK). The MDK is designed to accommodate multi-components and incorporate new models under development. These will be used to demonstrate the potential of flexible circuit design, based on measured ore properties and equipment performance.CITATION:Foggiatto, B, Hilden, M M, Powell, M S, Kay, P D and Andrusiewicz, M, 2012. Simulation of flexible circuits, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 291-298 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By H Esterhuizen

The Ernest Henry Mine (EHM) in Queensland, Australia is a Sub-level Caving operation that started production below the previously mined open pit at a depth of 535m. Current Production mining has progressed to a depth of 730m, with planned production mining to extend down to at least 1000m below surface. The inclined nature and geometry of the orebody combined with geological structures provides for challenging mining conditions. Over several years, Ernest Henry Mine has introduced measures to improve outcomes based on observations, monitoring and data analysis. As mining progresses deeper, EHM will continue to proactively take steps to ensure future outcomes are anticipated and mining can continue safely and uninterrupted. The focus of this paper is on the changes in seismic- and stress-driven behaviour of the rockmass experienced at EHM, the ground control measures implemented, and the anticipated future conditions and controls required. CITATION:Esterhuizen, H, 2018. The evolution of seismicity and ground control measures at Ernest Henry Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 20–41 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By M Reid, H Arbon

Hillgrove Resources (HGO) commenced open pit mining in 2011 and from 2011 to 2016 the geology team experienced a consistent negative reconciliation between grade control estimated copper (Cu) grade and the mill received grade. For the first four years, despite trialling various grade control strategies, the monthly variance between geology and mill copper grades fluctuated between -5 per cent to -17 per cent Cu metal depending on the style of mineralisation.In 2015, HGO embarked on various measures which resulted in changes to grade control practices under the advice of consultants. These changes to grade control sampling, estimation and block out practices resulted in six to seven months of consistently poor Mine to Mill reconciliations from -25 per cent to -28 per cent Cu.In an effort to mitigate these poor reconciliations the geology team reintroduced the preconsultant block out and geology driven grade control methods. Blockout reconciliations from this point emulated those seen originally from -8 per cent to -12 per cent (Cu per cent). Early in 2016 the geology team introduced conditional simulation for grade control as opposed to ordinary kriging to better characterise the grade distribution, introduced separate estimation parameters appropriate for every zone of mineralisation, implemented a maximum profit function to optimise the selection of ore and waste, and retained the geology driven block out processes. Since March 2016 the mine has experienced consecutive months of positive Mine to Mill reconciliations, the first seen in six years. Year to date the expected copper metal is within 1 per cent of mill reconciled copper metal.This paper will compare the various sampling methods, estimation algorithms and block out procedures from the past six years to arrive at a robust open pit operating procedure applicable for mineralisation with high short scale variability.CITATION:Reid, M and Arbon, H, 2017. Setting new standards at Kanmantoo – effective grade control procedures, in Proceedings Tenth International Mining Geology Conference 2017, pp 401–408 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By K Muller, T Oosthuizen

Blast exclusion zones are instrumental in protecting equipment and personnel. When there is no constraint in footprint, the exclusion zone can be enormous, practically eliminating the hazard of flyrock. Unfortunately, this may not always be the case and in many circumstances the blast design needs to be altered to suite such scenarios. When a conservative design approach is taken, it could completely eliminate any form of ejection, whether it is from the free face or the bench itself. The degree to which typical flyrock models describe fragment motion through air with ballistic flight equations are not justified when such a high level of control is applied. This paper examines various methods of risk analysis and suggests an approach to be used for controlled blasting.The outcome of principles discussed in this paper can be seen in video form (Mavmedia, 2014).CITATION:Muller, K and Oosthuizen, T, 2015. Should the blast exclusion zone be based on a qualitative or quantitative analysis? A practical implementation conundrum, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 425–428 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J de Vries

Arthur Page, a past President of AT&T said:All businesses in a democratic society begin with public permission, and exist by public approval. Product stewardship in its most basic form is simply risk management applied to the products we produce. Conceptually it may be considered as a more expansive approach to many existing safety, heath and environmental programs. Key differences include the extension of responsibility beyond the direct control of management, and consideration of the implications your products and processes have on the broader community, as opposed to the confines of an individual mine site or operation. This paper reviews the processes used by Orica Ltd to manage its product stewardship program. OricaÆs product stewardship program is expansive and supports activities and business that range from manufacture and delivery of commercial explosives and sodium cyanide to mines throughout the world, supply and operation of municipal water facilities, and manufacture and distribution of consumer products such as household paints and adhesives. We highlight the development of the program through experience both good and bad, and by use of case studies to illustrate how an active product stewardship program is an effective business risk mitigation strategy.

Jan 1, 2006

By M J. Newton

As part of the AMIRA P843 project Keeney and Walters (2008) describe how the principal components analysis (PCA) method can be used to identify classes of samples with similar metallurgical characteristics. However PCA does not take account of the location of each sample in 3D space. This paper describes a study to analyse the spatial distributions of the classes and determine appropriate modelling methods to control the estimation of the comminution parameters and mill performance indices into a 3D block model. This includes but is not restricted to geostatistical techniques that are used for grade modelling. The starting point for the study is the class definitions and the regression models for estimating the comminution parameters and performance indices. Each sample is assigned a class and the spatial distribution of each class has been analysed using different techniques including the calculation of variograms. This establishes whether the classes can be used as domain control for estimation into the block model – a procedure similar to using geological rock type domains for controlling the estimation of grades for a resource model. However, standard geostatistical estimation methods such as ordinary kriging assume that the variable being estimated is additive or linear. This assumption is valid for variables such as grade but this is not necessarily the case for the comminution parameters or the performance indices. Therefore the estimation procedure must either use variables that are definitely additive or the effect of potential non-additivity must be tested and accounted for where possible.The results of the study show how performance indices such as recovery, throughput and specific power can be estimated into the block model. This model is then combined with the geological model to provide a multi-parametric model that is used to optimise the mine planning and scheduling activities which can lead to significant improvements in NPV.

Sep 5, 2011

By G Kirk

Definition and delineation of in-pit ore and waste material are the most significant tasks for an open pit production geologist; adding or destroying value in the mining value chain. Anglo American’s Mogalakwena Platinum mine, an open pit operation in South Africa moving 100 Mt/a, has recognised the value of improved material definition and is in the process of changing from blasthole to reverse circulation (RC) sampling for in-pit grade control. This is aimed at obtaining more representative samples, which are required to maximise ore recovery, minimise waste dilution and to increase the accuracy and confidence of production forecasts. Early in the project, it was realised that the key risks for implementing RC grade control were related to change management processes, rather than failure of technology. Recognising the importance of this issue, Mogalakwena chose an integrated implementation approach that incorporates all stakeholders of the mining cycle in order to develop a process that delivers maximum value and is sustainable within an active mining environment. The following core goals were addressed over five phases of project implementation: extensive definition and design of integrated project implementation, comprising: project buy-in and ownership from all key stakeholders, including survey, geology, mine planning, drill and blast, load and haul, maintenance, supply chain and finance; and detailed analysis of all potential issues and possible solutions, allocated to stakeholders as part of the scoping process; optimising hole patterns and drilling procedures, focusing on delivering maximum value for minimum cost using multiple scenario analysis from borehole data and operational sequencing requirements; and evaluation of lessons learnt during project implementation in order to optimise the technical solution and operational efficiencies. Although this project is not yet finalised, Mogalakwena Platinum Mine is already providing a blueprint for the effective development, implementation and optimisation of sustainable in-pit grade control RC drilling for other open pit mines within Anglo American plc.

Aug 22, 2011

By B E. De Gee, N Viviers, A Naidoo

In 2013 the Mopani Copper Mine Mufulira plant in Zambia embarked on a project that was aimed at improving concentrator recoveries. The project commenced with the automation of the milling and flotation circuits. This involved the installation of new instrumentation, namely measurement devices and actuators, and the connection of these to new programmable logic controllers (PLCs).The infrastructure changes were followed by the implementation of basic proportional-integral-derivative (PID) controllers on the PLCs. Supervisory control and data acquisition (SCADA) interfaces were also implemented to allow for switching between controller modes, inputting of setpoint variables and to provide a visual display for process monitoring. The final phase of the project involved the installation and commissioning of advanced process control (APC) solutions on the milling and flotation circuits. This work was carried out by Mintek over 21 on-site days. The APC solutions included the MillStar and FloatStar suites of advanced controllers.The MillStar control suite focused on stabilising the mill feed and mill discharge on the two primary mills as well as the flotation circuit feed. Mintek’s CyLas instruments, which provide a measurement of the hydrocyclone underflow angle, were also installed. The measurements were incorporated into the discharge stabilisation control on both milling circuits. The FloatStar level stabiliser controller provided flotation cell pulp level control on fourteen cells, including two columns.Performance tests showed that the Mintek APC system stabilised the mill feed and mill discharge while ensuring the process remained within operational constraints. The MillStar control system utilised the CyLas instrument to prevent roping on the hydrocyclone underflow. This was not always achieved under normal operation. Additionally, the flotation section was stabilised as a result of improved level control by the FloatStar control system.Performance comparisons showed that the Mintek control system improved the operation of the milling and flotation circuits resulting in a greater copper recovery.CITATION:Naidoo, A, De Gee, B E and Viviers, N, 2014. Implementation of an advanced milling and flotation control system at Mopani Mufulira copper mine, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 363–368 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By S Harris, A Bossilkov

The Kwinana (Western Australia) and Gladstone (Queensland) industrial areas are among the few dozens of heavy industrial areas globally that demonstrate significant levels of regional resource synergies. Such synergies are also referred to as æindustrial ecologyÆ or æindustrial symbiosisÆ. Fundamentally they involve the exchange of by-products or sharing of utilities between companies in close geographic proximity to achieve competitive advantage and environmental benefit. A concerted research effort is currently underway to foster greater realisation of regional resource synergies in minerals processing intensive regions, in Australia and internationally. This paper summarises current insights from the foundation research into engineering tools and technologies and enabling mechanisms for regional resource synergy developments. Regional resource synergy developments were reviewed for 16 international and two Australian regions. It was found that Kwinana and Gladstone compare favourably with the well-regarded international examples of regional synergy development. Given the fairly strong evidence that self-organisation is critical for regional synergy developments, an implementation model has been proposed that captures entry points for synergy developments at the level of platform (industry collaboration), process (developing synergy opportunities) and project (assessing and implementing specific synergies). It was also found that regional synergies have so far developed in the absence of specific methods for identification and screening of synergy opportunities. Moreover, very limited attention has been paid to the associated technological and engineering challenges. The current technical research effort therefore targets: the development of a toolset for the identification and development of potential synergy opportunities; and assessment of technology needs and opportunities for regional synergies involving water, energy and materials recovery and reuse.

Jan 1, 2006

By G Bubner, C Gaughan

Magnetite mineralisation within the South Middleback Range has been known since the early 1930s; however, it was not until 1989 that BHP (then owners of the Middleback Ranges mining leases) drilled 10 700 m of diamond core into what was then known as the Iron Duchess low-grade deposit. In 2002 a review of Iron Resources left in the Middleback Ranges and the identification of downstream processing benefits using magnetite as a primary feed source led to the commencement of an 18 000 m resource drilling program of the high-grade core of the Iron Duchess low-grade orebody (renamed the Iron Magnet deposit). This paper describes the geology, processes and procedures used since drilling recommenced in early 2003. The Iron Magnet deposit is located 53 km southwest of Whyalla in the South Middleback Range, South Australia. It is a Paleoproterozoic stratabound magnetite deposit that lies down-dip and lateral to the Iron Duke hematite deposit, hosted within the Lower Middleback Iron Formation of the Hutchison Group meta-sediments within the Cleve subdomain of the Gawler Craton. Magnetite bearing host units within the Lower Middleback Iron Formation can be divided into a æmixedÆ basal sequence, a lower iron carbonate unit, a middle iron talc unit and an upper iron silica unit, all units grading up sequence and laterally into one another. The magnetite mineralisation is hydrothermal in origin. The strongest consistent mineralisation coincides with the iron carbonate unit, and the hematite orebodies of the Iron Duke are interpreted to represent up-dip supergene enrichment of the same unit. The Iron Magnet occurs within a large-scale parasitic syncline-anticline pair on the west limb of a larger syncline. Major bounding north-south shear zones occur on the east and west sides of the deposit. Cross-cutting west-northwest, northwest, northeast and east-northeast trending faults displace mineralisation. The commencement of drilling in 2003 lead to the migration of geological and geochemical databases, re-logging and re-assaying of all old cores that intersected the deposit, updating of logging codes and procedures, and strict Qa/Qc procedures to ensure the study satisfied JORC standards. External consultants were used for auditing and bench marking. The strong geophysical responses of magnetite and the wealth of close spaced ground magnetic and gravity data already completed over the Middleback Ranges allowed for refining of drill hole targets for the drilling program. It also provided an indirect method for ascertaining magnetite grade and tonnage volumes.

Jan 1, 2005

By T Walkemeyer, R Elliott, D Chang-Martin

Over the past decade, discrete element method (DEM) simulations have seen increasing adoption by the resources sector to inform the design of materials handling equipment such as transfer chutes, bins and hoppers. But, if ‘all models are wrong, but some are useful’ (Box, 1979) what approaches are available to check that a DEM simulation is useful? How to avoid garbage in equals garbage out. This work considers what properties of bulk solid flow behaviour are important to transfer chute simulation. Cohesive bulk solids (such as sticky iron ore fines) can develop sufficient strength to form a stable cohesive arch, this phenomenon is not well predicted by measurements of angle of repose. This work presents a two-part approach to the development of a useful DEM model that can be used to add value to the design and optimisation of bulk materials handling equipment. Part 1 is the calibration of not just one, but a range of material models chosen to envelope the range of anticipated materials that will be handled. This work describes the DEM simulation of a batch of direct shear cell tests to develop material models that can be measured by the same metrics routinely used to characterise the flowability of cohesive iron ore fines. Part 2 of this work describes systematic methods for validation of the transfer chute DEM simulations. The DEM model is only useful if it can adequately represent the typical problems observed within a transfer chute, such as blockages due to build-up and cohesive arching. Proper validation requires good observations. Validation examples of site observations are shown side-byside with simulations to demonstrate the adequacy of the DEM model and calibration approach. DEM simulations have the potential to add significant value by allowing engineers and designers to predict material flow-through equipment based on a range of material properties, allowing for stress testing designs and making iterative improvements.

Sep 18, 2023

By Y A. Stepanyants, J Crawford

A practical field method for determining the maximum value of the intrinsic oxidation rate, Smax , of sulfidic materials in waste rock dumps is proposed. Knowledge of the intrinsic oxidation rate of sulfidic materials distributed in a dump is necessary for predictive modelling of oxidation and pollutant generation over time. The suggested method uses the fact that drilling waste rock dumps to install probes for monitoring temperature and oxygen concentration causes large volumes of air to be injected into a dump by the drill rig. By measuring the rate of decrease of oxygen concentration along the length of a borehole immediately after installation, it is proposed that Smax can be calculated at different depths. The aims of this work were: to derive a simple, practical formula for the estimation of Smax from the oxygen concentrations measured over time, based on some simplifying assumptions; to use a two-dimensional numerical model that incorporates all the necessary physical processes to model the behaviour of an aerated dump over time for a reasonable range of dump and material parameters; and to compare the results of the two approaches to assess the validity of the simple formula as a method for estimating Smax. It has been found that the technique can provide reliable estimates of Smax when the value is of the order of 10-7 kg(O2) m-3 s-1 or greater. At the lower end of the range however the radius of the zone aerated during drilling becomes an important parameter and further work has been recommended to investigate this aspect of the method.

Jan 1, 2003

By M Edwards

The paper outlines the successful application of some of the on-belt technologies available from Scantech International Pty Ltd and how these have provided benefits in a number of mining and mineral processing operations. Effective process control requires real time analysis so quality can be fed back to the previous process and fed forward to a subsequent process. A range of on-belt analysers that allows for full stream, continuous, non-contact analysis of conveyed materials is available to achieve this. Real time results can provide timely information for effective process control. Benefits of on-belt analysis systems become more evident once the true variability of material quality and moisture content in conveyed flows is measured. To obtain economies of scale in mineral processing operations large material flows are achieved using conveyors. The cost and effort to sample representatively increases as conveyor flows increase. One sample may represent a few tonnes or up to 10 000 tonnes of material. The turnaround time between sampling and availability of sample analysis data does not allow real time process control. Tonnage flow rate, moisture content and elemental or mineralogical composition are required to perform effective process control of most conveyed streams. Tonnages can be effectively measured using belt weighers. The analyses derived from small samples supplied by conveyor-based sampling systems contain high variability. On-belt, continuous analysers see all the material and, through short term compositing of analyses, supply less variable results. Real time analysis helps operators develop a better understanding of material variability. Analysers can be effectively utilised to improve the consistency of product quality through bulk sorting and blending control. Many existing users of the technologies have gained competitive advantages through their ability to supply a more consistent quality product to the market.

Jan 1, 2008

By Lawrence M. J

It must be stressed that the following comments are offered only to assist mineral industry professionals in understanding the issues involved in personal liability. The information and views expressed herein are not intended to be a comprehensive guide or definitive statement of the law and they should not be regarded as a substitute for specific advice for individual situations. Readers should consult their own legal and other professional advisers before applying the content of this paper to their own particular circumstances. It is hardly news that work in the mining industry is governed by a complex regulatory and legal system which is constantly changing, but few realise just how directly they can be affected and become personally liable for any breaches. These may result in civil or criminal proceedings and personal assets are at risk. Owners, company directors, managers and now employees are at risk, together with consultants, contractors and suppliers of equipment or consumables, as well as government inspectors. They are liable for their personal decisions to act (or failure to act) in managing operations or carrying out directions, as well as for the actions of others under their control. This paper identifies the areas where such individuals in the open pit mining industry in Australia face the risk of personal liability and measures which can be used to minimise the risk or which can be used to make out a defence to legal action which could arise. There have always been a myriad of Commonwealth, State and Local Government laws and regulations with which to comply, and now international protocols are being used as a basis to impose greater obligations on all people. Once, the `corporate veil' gave some protection to the individual, but today there is negligible protection from the full force of the law. Not only are there various types of law enforcement officers, but public interest groups, shareholders, customers, suppliers, creditors etc may litigate. This paper is not intended to be an exhaustive discussion of the provisions of all the legislation or case law where individuals can be held) personally liable. These areas would include environmental, pollution and heritage law (including Aboriginal sacred sites); occupational health and safety (including workers' compensation) law; trade practices and fair trading law; contract law; corporations law (including the requirements of the Australian Stock Exchange [ASX] and Australian Securities Commission [ASC]); industrial relations law; anti-discrimination and sexual harassment law; taxation (including superannuation trustee) law; and the Common Law. The focus is on the following areas of regulation, which are outside the usual experience of those in the open pit mining industry (the Mining Acts and Regulations are specifically not dealt with here): ò Environment Law; ò Trade Practices Law; ò Occupational Health and Safety Law; and ò Corporations Law.

Jan 1, 1994

By A B. Jahed, Ö Aydan, T Ito

In this study, the authors compiled some case history data and present some typical examples of rock slope stability issues in Afghanistan with a special emphasis on Kandahar region and categorise rock slope failures according to the principles of modern rock slope engineering. The slopes considered involve rock-cut, natural rock slopes mainly. The effect of structural geology and discontinuous nature of rock mass on both slope-cuts and natural rock slopes is taken into account and some preliminary assessments on the stable and unstable rock slopes are presented. Furthermore, the seismic effect on their stability is also considered. It is also pointed out that similar issues could be observed in open pit mines, which may be exploited in years to come.

Nov 29, 2022

By D Cork, R Peet

"Methane is a signifi cant greenhouse gas. Methane is released from coal seams during the mining process, both in surface and underground operations. This uncontrolled release is termed æfugitive emissionsÆ and in underground mines is transferred to the atmosphere in ventilation air, known as ventilation air methane (VAM). The global VAM emissions are over 369 Mt of CO2-e/a (Butler, 2011; US EPA, 2010). Coal mines may abate this VAM or consider abatement should there be a price on carbon. These fugitive emissions are heading towards ten per cent of AustraliaÆs emissions by 2020 (Department of Climate Change, 2011).There are safety issues involved in VAM destruction. Due to the nature of coal, and coalextraction, unpredicted methane spikes above the lower-explosive-limit (LEL) can occur in theventilation air; for example outburst events or ventilation failure. This could lead to a mine fi re ifthe mine ventilation air was connected to a VAM abatement plant and the risks are left unmitigated.CorkyÆs is working with the mining industry to directly address these safety issues. CorkyÆs calltheir technology VAM RAB, which stands for ventilation air methane regenerative afterburner(VAM RAB). VAM RAB utilises the principles of a thermal oxidiser.This paper discusses fi ve independent layers of protection (ILPs) to fi rst stop methane reachingthe thermal oxidiser and secondly prevent the fl ame front from burning away from the VAMRAB. The test work completed or contemplated includes safety integrity level (SIL) assignmentto various vents, barriers and door systems to prevent a fl ammable mixture reaching the VAMRAB, proven rapid response methane monitoring sourced from the petrochemical industry, anddefl agration experiments to test the eff ectiveness of the passive geometry and active engineeringcontrols. These experiments and SIL assessments indicate that it is possible to safely connect theVAM RAB to a working coal mine.Further work is required to upscale the pilot safety work. Refi nement to the design is possible;for example improvement to safety duct controls once trialled at demonstration scale plus thermalenergy capture for power generation or other applications to provide heat. Nevertheless, thispaper shows how safety issues can be managed by a multilayer of protection approach usingvents, barriers and doors, and appropriate thermal oxidiser geometry."

Jun 1, 2012

By N McIntyre, M Edraki, K R. Jain

From the very early stages of a mining project, there is a requirement to predict the chemistry of potential drainages from various waste storage facilities. However, using relative masses to scale chemical loads measured by laboratory kinetic tests, such as humidity cells, to a full-scale mine waste facility will lead to concentration predictions that are unrealistically high for many dissolved constituents. Scaling factors developed by various procedures indicate that laboratory rates may range anywhere from two to eight times (Drever and Clow, 1995) to 100 to 1000 times faster than field rates (Malmstrom et al, 2000; Smith and Beckie, 2003; Ritchie, 1994). This contribution will use previous works and secondary data to discuss the significance of scale in water quality predictions. It will also present primary experimental geochemical and numerical data from a column leaching study on coal spoils to discuss potential applications of mesoscale leaching tests in bridging the gap between bench-top tests and field scale trials.

Aug 2, 2023

By S J. Schafrik, E S. Gilliland, E C. Jong, J Waynert, C W. Weiss

Two commercially available through-the-Earth (TTE) communications systems were evaluated at an active underground longwall mine in West Virginia. One system utilises magnetic field (H-field) antennae while the other system utilises electric field (E-field) antennae to achieve communication. A large portion of this mine is overlain by an inactive gas-oil field composed of densely spaced wells. This feature provided a unique opportunity to determine the impact of cased wells on both TTE technologies. The following communication modes were investigated: surface to underground, underground to surface, underground to underground and real-time two-way communications. Standard deployments of the TTE systems using the manufacturer’s recommended procedures were able to achieve clear communications between underground and surface locations under certain circumstances. As a result, the design and deployment that will optimise TTE transmissions are unique to each system and to the specific area of the mine. This field study was conducted as a part of a larger multisite evaluation of available TTE systems in an effort to determine their operational sensitivity. The performance of these two TTE systems suggested that one may be preferable over the other depending on the conditions present during deployment.CITATION:Jong, E C, Schafrik, S J, Gilliland, E S, Weiss, C W and Waynert, J, 2015. Pairing magnetic and e-field through-the-Earth communication systems based on mine site conditions, in Proceedings Third International Future Mining Conference, pp 245–252 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By M Colwell

The Coal Mine Roof Rating (CMRR) is a rock (roof) mass classification (RMC) system/index that was originally developed by the United States Bureau of Mines (USBM) for aspects of underground coalmine geotechnical design and was first introduced to Australia as a part of the original Analysis of Longwall Tailgate Serviceability (ALTS) project conducted in 1997/1998. In subsequent years further refinement to its calculation was undertaken, such that the CMRR is now an industry standard for quantifying the structural competence of the primary bolted roadway roof interval and has been routinely/widely used by Australian collieries over the last 25 years with great success for roof support/chain pillar design. There have been many publications discussing the use and calculation of RMC systems and this paper also provides an important update and recommendations in how best to calculate the CMRR. However, it is rare to find an explanation as to why and how a RMC system/index satisfactorily takes account of the mechanics and rock mass behavioural issues associated with ground reinforcement. This paper provides such an explanation and insight with respect to the CMRR so it is: 1) better understood, 2) to allay any concerns, and therefore 3) will continue to be confidently used by and for the collieries’ benefit.

Nov 29, 2022