Search Documents

Folklore suggests that oxidation is detrimental to sulfide mineral flotation, and in many instances is the reason given for values reporting in the tailing. However, while a considerable body of work examining galena oxidation is available in the literature there are very few studies that investigate the consequences of galena oxidation on its subsequent flotation in base metal sulfide ores. This work clearly demonstrates that pyrite forms a galvanic couple with galena, due to the large difference in their rest potentials, and results in accelerated oxidation of galena, particularly as the pyrite content of the ore is increased. The most obvious effect of the galvanic oxidation of galena by pyrite is the release into the system of galena oxidation products, providing an ample supply of lead ions available to activate gangue minerals, most notably of which in lead/zinc ores is sphalerite. The inadvertent activation of sphalerite by lead ions inevitably leads to the recovery of liberated sphalerite into the lead concentrate, and as a consequence a reduction in the lead concentrate grade. That is, a loss of selectivity for galena against sphalerite. If galena oxidation is excessive not only is there a considerable loss in lead concentrate grade, but also a marked decreased in lead recovery as the flotation rates of the gangue minerals increase, until they rival that of galena.

Jan 1, 2005

By A Seneviratne, Y Li, N Udugampola, X Ai, B Li

LoRa (Long Range) is a low-power, long-range wireless communication technology that has gained significant research interest for its potential use in multi-hop linear wireless sensor networks (LWSNs) for underground mines. These networks deploy LoRa-enabled sensor nodes in underground mines, together with LoRa repeaters placed along mine tunnels to relay sensor data to a LoRa gateway, which connects to a backend network for application-level processing. Since the packets generated by sensor nodes farthest from the gateway have to hop through many repeaters, their probability of successfully reaching the gateway is significantly lower due to the higher chance of packet collisions compared to sensor nodes closer to the gateway, resulting in a lack of network fairness for the sensor nodes. In this paper, we first present an algorithm to improve the fairness of a LoRa LWSN by grouping neighbouring nodes and adjusting the number of packet re-transmissions and transmission intervals for each group. Then, we demonstrate that the fairness of a simulated LoRa LWSN can be improved by approximately 500 per cent by applying our algorithm. We verify our algorithm with network simulations under different network traffic levels and grouping strategies, obtaining fairness improvements in each scenario. Our algorithm and results will pave the way towards developing highly fair LWSNs for underground mining applications.

Sep 1, 2024

By B Broad

"Establishing ventilation in the early stages of a new mine is an essential step to achieve scheduled outcomes that ultimately drive the financial success of an operation. If the primary ventilation is not in place in time to support a contractorÆs work output, then the ore delivery is likely to be severely impacted. Options to increase ventilation in order to address shortfalls are limited. This in turn can lead to reduced revenue generation at a time when a mine is at its highest capital outlay. This can have implications for any company, but even more for an explorer moving to producer. The ventilation put in place to cover the start-up period is also unlikely to cover any extended or increased load required to meet schedule delays.The following paper examines two issues in relation to ventilation with a focus on small to medium projects where the company is establishing a mine using a mining contractor. The issues being: potential impacts on the contract and tender process when using a mining contractor key mine design considerations, such as æcrunch timeÆ, as they interact with ventilation achieving a successful ramp up.A recommendation is made for higher levels of detail around secondary ventilation leading up to the primary fan installation. The information should be included as part of the tendering process and preliminary project execution planning. Understanding the æcrunch timeÆ concept can lead to strategies, as well as back up plans, to minimise any negative impact.By understanding key risks around primary ventilation establishment for a new mine, detailed design work can be completed where it is needed most. Value is added by reducing uncertainty and a payback with better contract terms and a more robust ramp up plan. This will improve the economic return for the company and reduce the risk.CITATION:Broad, B, 2013. Contract considerations and other critical ventilation aspects in achieving a new mine ramp up, in Proceedings The Australian Mine Ventilation Conference, pp 207-214 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 1, 2013

By Bigdy D. N

The paper describes a system for providing mine management with a continuous indication of the effectivness of longwall coalface powered supports in controlling roof-to-floor convergence. The system comprises on-face instrumentation monitoring convergence and support leg circuit pressures, a means of transmitting the output of that instrumentation to the surface for collection, and software which presents both a condensed analysis for rapid review of the current state, and extended analyses from which remedial action can be recommended if a problem is identified. The results of a field trial are presented showing that meaningful results can be obtained.

Jan 1, 1988

By A Millar, B Wraith

Process plants are characterised by variability of performance over a wide range of time-scales; reflected in fluctuations in metal recovery, concentrate grade, plant throughput and reagent costs. In turn, these fluctuations impact financial metrics such as operating costs and revenue. The primary cause of plant variability is variation in the physical, lithological and mineralogical characteristics of the ore fed to the plant. The variability of the ore is driven by the intrinsic heterogeneity of the geology and mineralogy of the orebody, the mining method and mine production plan, the capacity to stockpile and blend, as well as the plant flow sheet and the level of plant automation. Whilst the impact of ore variability on process plants is universally recognised, it is rarely quantified in financial terms. Consequently, opportunities to reduce its impact are often overlooked due to the lack of a basis for a quantifiable cost-benefit analysis to justify improvement initiatives. This paper will present case studies using production data from the Renison tin concentrator and a zinc concentrator. These case studies demonstrate that as the standard deviation of plant head grade increases (as a proxy for ore variability), plant metal recovery subsequently reduces. The metal recovery is then converted into plant revenue losses, to quantify the economic impact of ore variability. The Renison case study demonstrated that whilst a very rare occurrence, revenue losses were as high as 34 per cent (relative to the baseline) when standard deviation was at its highest. The zinc concentrator case study demonstrated that revenue losses were as high as 6 per cent (relative to the baseline) when standard deviation was at its highest. Options are available for reducing and managing ore variability in the process plant. These options include changing mining practices so that the ore is fed to the plant with less variability, more advanced process plant control systems and the use of predictive geometallurgical models.

Aug 24, 2022

The mining industry, both here and internationally, is continually developing increasingly sophisticated software to compute mineral resource estimates, but these processes cannot compensate for a flawed geological interpretation of the geology of the economic commodity(s) concentrations. Quality assurance and quality control (QA/QC) is becoming increasingly common in association with the sampling and assaying practices within the industry. However, it is rare in the case of a geological interpretation associated with mineral resource estimation. Why? In the context of this paper, QA/QC relates to the use of statistical and graphical tools to show that the geological economic commodity concentrations have been appropriately domained. Domaining is essential to improve the chance of getting a mineral resource estimate right. Commodity value and acceptable concentration variation within a mineral resource can be ingredients that make mineral resource estimation difficult to get right. But it is possible to get it right a very high proportion of the time. It is more likely to occur when inappropriate data consolidation is minimised. In any case, inappropriate data consolidation is significantly reduced when the geological interpretation is strongly consistent with the data and it is demonstrable. To achieve quality global estimates of geological domain concentrations, it is essential that the geology of the prospect is understood sufficiently that the deposit is appropriately domained. Appropriate domaining occurs when sample populations are separated in such a way that only data in harmony with each other within the population contributes to the domainÆs concentration estimate. The paper will use four brief case studies to illustrate how QA/QC can be used to display data and validate the underpinning geological interpretation through its associated domaining to get it right when it comes to a mineral resource estimation.

Jan 1, 2007

By Higuchi K, Sekimoto Y

In this report,the results of the large diameter drilling tests in coal seams assisted with water jet are described. The stress relief in coal seams by this new method is as effective as by the conventional method and the penetration speed by this method is 1.5 times as fast as by the other method. 1 Introduction The average mining depth of Japanese coal mines has already attained about 700m from the surface. Almost all coal mines are suffered from occurrence of coal and gas outbursts. To prevent outbursts, some countermeasures are taken generally. In particular, large diameter stress relief borings have been carried out quite often at Akabira coal mine located in the northern part of the Ishikari coal field in Hokkaido,JAPAN. These borings have had successful results but the drilling work of such large diameter

Jan 1, 1987

By D Fargher

BHP BillitonÆs Cannington operation began production in 1997 and is presently the largest tonnage and lowest cost single mine producer of both lead and silver in the world. The original design capacity was 1.5 Mtpa and this has progressively increased via a series of debottlenecking projects in both the mining and milling operations. In 2003, 2.39 Mt of ore was mined, whilst 2.31 Mt of ore was milled. In February 2003 Cannington received approval to expand the project to a sustainable capacity of 2.4 Mtpa. This resulted in underground development into the northern zone, upgrades to the concentrator, increased accommodation at site and power station capacity. The Cannington project development team implemented a partnership approach to the project. Fraser Osborn Engineering and Outokumpu Technology worked closely together with the Cannington team to meet all of the project constraints.

Jan 1, 2004

By Armstrong A

Queensland is Australia's second largest mining state with world-class deposits of coal, base metals, bauxite and magnesite. The total value of Queensland's mining production is about $5 billion per annum, and coal accounts for around 55 per cent of that total. The environmental issues which arise as part of management and regulation of the industry are resolved within the EMOS process. The Environmental Management Overview Strategy is the cornerstone of the policy 'Environmental Management for Mining in Queensland' developed jointly by the Queensland Department of Minerals and Energy and the mining industry. The Gordonstone Coal Mine is the largest underground mine to gain approval under the new policy. Accordingly, Gordonstone has a well planned environmental management program which takes into account site-specific factors and provides for continuous compliance with the provisions of the Mineral Resources Act in a self-regulatory context.

Jan 1, 1994

By Real F, Carvalho P

During the development of the Neves-Corvo Underground Copper Mine, since 1981, inflow of water has been encountered in the mine workings, which consist of a ramp from surface 5 km long, a shaft 575 m deep and access crosscuts through the massive sulphide orebodies of Neves, Corvo and Graga, which are three of the four known deposits up today. Mine-hydrological studies have established the main characteristics of the hydrological system and its evolution in space and time. In a geological setting of low permeability rocks of Paleozoic age, tectonically affected by thrusts and faults, this has involved consideration of the relation with surface and ground water as a result of mine dewatering processes. The hydrological systems are described and summarized in this paper together with the techniques employed to study their origin and evolution, namely hydrochemistry, thermometry, piezometry and isotopic tracers.

Jan 1, 1988

In the future to excavate sufficient coal for power generation, two dredgers would be required to dig overburden or interseam 70010 of the time and three dredgers 40010 of the time. One overburden system was not adequate for this requirement, making coal production reliability vulnerable. TS5 spreader is the new machine element of this system. The selection of the best type of machine configuration to suit the application was then subject to an internal SECV VE Study, a registration of interest and a tender for two machine alternatives. This paper outlines the reasons why SECV planned the Secondary Overburden System and how the Krupp machine met these requirements. It also identifies the main design features of the machine and its constructability which will allow the machine to be operational by the end of May, 1990.

Jan 1, 1989

By Lewis J. W

The mineral sand orebodies of the east coast of Australia occupy approximately three per cent of the dune-heath-wetland coastal environment. They are associated with coastal plant communities ranging from Holocene high dunes carrying mature Eucalypt forests to low- lying heaths on Pleistocene deposits. Commonly, 0.25 to 1.5 per cent of the sand volume mined is removed from the site. Therefore, the volume change is insignificant. The equipment and techniques in use are flexible and the land can be returned in a manner suited to its subsequent use for grazing, subdivision or recreation. Landforms similar to the pre-existing are created in two case studies given. Sophisticated revegetation techniques are practised and are discussed in two case studies. Pre-mining vegetation surveys and post-mining monitoring are used to guide the management of the ecosystem.

Jan 1, 1976

A mechanised sub-level overhead benching method is used at Cleveland, to produce 22,000 tons per month of ore assaying 0.92% Sn and 0.40% Cu. The ore occurs in a series of vertical lenses which can be mined by open stoping. Levels are developed at 60ft., vertical intervals by jumbos. The ore is silled out and the stope block formed between levels drilled out by long hole drilling. Each row of holes is fired and broken ore within safe reach from the stope brow is mucked out by Wagner ST-5A Scoop Trams. The remaining broken ore is recovered on extraction of the next lower level. Ore is hauled by road to the crusher station from the mine. As mining proceeds below the lowest surface portal a spiral decline will be used for ore haulage and mine servicing.

Jan 1, 1970

There are serious problems in forecast- ing accurately and achieving this goal depends on good quality information, correct assumpt- ions and sound analysis. planner. The forecaster must focus attention on a number of key areas of interest. These areas include major economic trends and changing GNP structure, consumption time series, end-use consumption patterns and substitution potential, accurately updating data bases (up to 5 years ahead), random factor estimation and examination of both long term and secondary mine potential. While metal price forecasting has suffered due to recent uncertainties, with increased importance on planning tools and cost analyses, it is still a necessary function. Forecasting is subject to the real world and the metal industry is made up of imperfect markets in a dynamic state. The real world provides the challenge to improve the accuracy of forecasting.

Jan 1, 1983

By C Simpson, J Market

The process of sampling blasthole cones utilising personnel to manually shovel material into sample bags is a long-standing industry accepted process. However, this method has several drawbacks, including the safety issues around having personnel performing manual sampling in a harsh environment and the variability involved in getting a human to repeatedly get a ‘shovel full of dirt’, and make it always representative. Geophysical blasthole sampling, or utilising a Downhole Assaying Tool (DHAT) has been tested and has now begun implementation at many iron ore sites throughout the Pilbara region, Western Australia. This method uses a geophysical tool to capture data within blastholes, and together with a semi-autonomous logging platform to minimise risks around manual handling, delivers a multielement proxy-assay which can be utilised by the mine geology team to accurately domain the orebodies. Logistically, the combination of a specially designed tool and semi-autonomous truck are the way forward for a safer and more data-robust blasthole sampling practice. The method utilises a neutrongenerating geophysical tool and linked elemental spectroscopy sensor, which measures the response of the material surrounding an open hole. This delivers results at submetre intervals. These results are then utilised, similar to blasthole sample results, to map out areas within the blast pattern that are ‘ore’, ‘waste’, or ‘other suitable grade’. This paper outlines a project that has been in ‘proof of concept’ at selected Fortescue sites over the last few years with testing of these tools carried out on reverse circulation (RC), diamond drill and blastholes. The method is now being implemented at operational hematite mine sites. Fundamentally, the method adds more than enough value to justify its implementation. The aim is that these learnings will enable the greater industry to adapt, implement and improve their mining practices. Ultimately, the outcome will be greater value in mining for the industry by having a larger volume of good quality data to make reliable decisions on material movements, minimising ore-loss and dilution, and maximising the value of our current and future orebodies.

Nov 8, 2021

As a result of the rapid economic growth in Japan, environmental problems have become a national concern in the latter half of the In 1967, the Basic Lair for Environmental Pollution Control was enacted as a fundamental ::olicy in this field. This lair provided compre- hensive guidelines for the action to be taken pollution prevention. The biggest problem n air pollution of those days was that of the sulphur dioxide content of the atmosphere. Based upon the law, the smelters in Japan have struggled hard to solve this difficult problem. Consequently, the ambient SO2 level has been lowered gradually year by year. At present, the ambient SO2 level is nearly equal to that in the atmospheric background. Furthermore, the fixation ratio of sulphur in Japanese copper smelters has attained up to 99.5 per cent.

Jan 1, 1980

By Corbett GJ, Leach TM

The Nena Cu-Au high sulphidation deposit has formed within the Frieda River Intrusive Complex in association with a major dilatant structure. Multiple intermediate intrusives of Miocene age are localised by a splay (Frieda Fault) of the Fiak-Leonard-Schultz Thrust, a several hundred kilometre long structure, formed parallel to the accretionary prism of northern Papua New Guinea.The high sulphidation systems including Nena, crop out as narrow silica-alunite ridges extending for up to 5-6km in length within a dilational structural environment. Alteration at Mena exhibits two phases of hydro-thermal activity: an initial stage, inferred to be volatile-rich, which has produced zoned alteration; and a later phase, postulated to have been a liquid-dominated fluid, which has brecciated earlier alteration zones and deposited gangue phases as well as Cu/Au-bearinq sulphides in open spaces.

Jan 1, 1994

By Heesteman LJL, Turvey DJ

The Mangani mine in West Sumatra is historically one of the most important precious metal mines in Indonesia, although the past production by World standards is small, totall- ing 5.66 tonnes gold and 242 tonnes silver. The geology is dominated by a distinctive NW-SE graben structure formed by dextral splay faults from the Sumatran Fault System. Quartz- rhodochrosite-rhodonite-Ag-Au veins are hosted by Tertiary pyroxene andesite volcanics and quartz-phyllite conglomerates, on N-S tensional fractures which intersect the Mangani graben. Intrusive rocks include andesitic dykes, pyroxene microdiorite, and hornblende granodiorite. Quartz-epidote-pyrrhotite alteration is related to concealed intrusions. Precious metal vein mineralization is characterized by: high Ag/Au ratio (>25); complex sulphide mineralogy of Fe, Mn, Ag, Cu, Pb, Zn, As, Se and the occurrence of Sn as stannite; low total sulphide content (

Jan 1, 1987

By Miyashita T, Yamamoto R, Kishimoto s

Following considerations of the effect of furnace size on pressure loss, pressure loss in front of tuyeres, gas flow in the lower parts of the furnace, the distribution of the burden and the gas flow in large blast furnaces is examined with particular reference to the burden distribution at the throat and the gas flow at high production rates. Improvement of gas flow is related to application of super-high top pressure and the use of moveable armour. A brief description of the NKK type moveable armour is given and its use in controlling the gas flow outlined. The operating results under controlled gas flow show an increase in production of Fukuyama No. 5 BF from 9,200 tpd to 11,000 tpd with a decrease in the fuel rate from 490 kg/thm to 460 kg/thm.

Jan 1, 1975

By A M. Nyembwe, A M. Garbers-Craig, R Cromarty

With the depletion of high-grade lump iron ore, concentrates have been identified as an alternative material for sinter making. Adding concentrates to the sinter mixture reduces sinter bed porosity and gas flow through the sinter bed. This will result in lower sinter strand productivity. A potential solution to this problem is to add concentrate in the form of micropellets. This study investigates the effect of concentrate and micropellet additions on the permeability of the sinter mixture. Permeability was measured on sinter mixtures containing ten to 40 per cent concentrates and micropellets at various moisture contents. The effect of concentrate and micropellet addition on the permeability–moisture relationship was examined. The results confirmed that the addition of concentrates into the sinter mix decreases the maximum permeability of the sinter bed. The incorporation of micropellets into the sinter mix reduced the permeability less than concentrate addition. The study also showed that the maximum permeability of sinter mixes containing concentrate is reached at the same moisture content as the sinter mixture without concentrate addition. For sinter mixes containing micropellets, additional water must be added to obtain maximum permeability. Parameters including the granule size, void fraction and angle of repose were also investigated to evaluate their effects on the sinter bed permeability.CITATION:Nyembwe, A M, Cromarty, R and Garbers-Craig, A M, 2015. Effect of concentrate and micropellet addition on iron ore sinter bed permeability, in Proceedings Iron Ore 2015, pp 69–76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015