Search Documents

By K R. Vining, T E. Norgate

A study was carried out to compare the environmental impacts of the two major iron ore agglomeration processes, sintering and pelletising, using life cycle assessment (LCA) methodology. The following agglomeration processing routes, with the fuel options shown, were investigated:sintering with combined natural gas/coke breeze or charcoal as fuel, grate-kiln pelletising with combined natural gas/coke breeze as fuel, and straight-grate pelletising with combined natural gas/coke breeze as fuel. Inventory data for each process derived from the literature, and in some instances supplemented by additional simulations and calculations, were used in the study and the environmental impact categories considered were gross energy requirement (GER), global warming potential (GWP) and acidification potential (AP). The results of the study showed that the GER, GWP and AP for a sinter plant are higher than those for a pellet plant for the same amount of metallic iron in the agglomerated products. These results are partly due to higher consumption of solid fuel and flux in the sintering process. However, it should be pointed out that the study only compared substantially fluxed sinters with acid pellets that may require additional flux (and hence potentially more greenhouse gases emissions) to be a balanced blast furnace feedstock. Extending the LCA to the blast furnace process stage was beyond the scope of the current study. Within the sinter plant, the sintering stage itself is the largest contributor to the GER, GWP and AP. In the case of pellet plant, the pellet induration stage is the largest contributor to the various environmental impacts. The GER and GWP of a straight-grate pellet plant are marginally higher than those of a grate-kiln pellet plant due to the higher electrical power required by the straight grate system. The substitution of coke breeze with charcoal in the sintering process results in an increase in GER but a decrease in GWP. However, a substantial proportion of the GER is derived from renewable sources (wood), resulting in a decrease in the non-renewable components of this environmental impact. Given the source of the inventory data and the assumptions and approximations made in carrying out the LCAs, it is emphasised that the results presented in this paper should be considered as indicative rather than as definitive results for the two iron ore agglomeration processing routes considered.

Jan 1, 2006

By I Ritchie, G Lane, C Morley, D Yataco

Marcobre SAC (Marcobre) is developing the Mina Justa project in Peru. The project has a lower grade oxide orebody overlaying the higher grade sulfide orebody. The oxide ore is treated by acid leaching; consumption of acid is high and is managed by vat leaching rather than the more conventional heap leaching process.The leaching process uses ore crushed to 100% passing 8 mm to optimise copper recovery. Acid consumption generally increases with a higher proportion of fines. Marcobre is investigating a three-stage crushing circuit with high pressure grinding rolls (HPGR) in the third stage, instead of the more conventional four-stage cone crushing circuit. The use of HPGR can result in higher fines production due to the higher compression forces in the crushing zone. This paper reports on the outcomes of the test work completed by Marcobre in 2016 and 2017 to manage fines production and compare the use of HPGR with conventional crushing on a high acid consuming ore.At moderate pressing forces, a HPGR crushing circuit appeared to produce similar size distributions to cone crushing. On average, both the copper recovery and the acid consumption in subsequent vat leaching were higher with HPGR crushing than with cone crushing.CITATION:Lane, G, Morley, C, Yataco, D and Ritchie, I, 2017. Are there differences in size distribution when comparing conventional crushing and HPGR?, in Proceedings MetPlant 2017, pp 60–72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By R Zhang, J Xu, X Lv, C Bai, S Zhang

This paper studies the grinding behaviour of vanadium-titanium magnetite concentrate in a ball mill. The grinding kinetics, surface morphology, lattice distortion, wettability and moisture capacity were analysed. Grinding kinetics equation was established based on population balances model with the size distribution data from a laser diffraction technique. The SEM photos of the ground concentrate showed that the surface gets rough with increasing grind time. Agglomeration of fine particles was enhanced when the grinding time reached 30 minutes. X-ray diffraction results showed that a loss in crystalline occurred with increasing the grinding time. The peaks of the X-ray diffraction patterns are significantly broadened with increasing grinding time. Wettability, characterised by contact angle between the material and water, improved due to the fact that the surface roughness increased with increasing grinding time. Moisture capacity of concentrate ascends abruptly in the first three minutes and then changed slowly with increasing grinding time. The water transfer coefficient in the particles increased rapidly in the first six minutes and then decreased quickly until grinding time reached 12 minutes.CITATION:Zhang, R, Lv, X, Bai, C, Xu, J and Zhang, S, 2013. Wet grinding of ?vanadium-titanium magnetite concentrate in a ball mill, in Proceedings Iron Ore 2013 , pp 511-518 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By R Moreby, J Kok, L van den Berg

The high production rates achieved from mass mining methods such as block caving, sublevel caving and longwall mining require large conveyor belts, trucking loops (diesel/electrical) and rail systems for ore handling. However, the ore handling systems used in mass mines introduce a significant amount of heat into the overall ventilation system, which may be problematic at depth or in mines located in hot climates.In particular, the heat load from a conveyor system is not always well understood and consists of various components, including frictional heat from idlers, heat from electrical motors, heat from the drive train and heat from broken rock transported on the conveyor system. This paper presents results from a study that investigated the heat introduced to the ventilation air from a large conveyor system. The conveyor system transports ore with a maximum virgin rock temperature of 41°C from a depth of over 1 km. Air, belt and rock temperatures were measured in the conveyor system to evaluate the distribution of heat loads.CITATION:van den Berg, L, Moreby, R and Kok, J, 2015. Heat load estimation from conveyor systems in mass mines, in Proceedings The Australian Mine Ventilation Conference, pp 63–70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By J P. Sykes, A Trench

"World-class mine projects are increasingly failing to become world-class mines. Non-technical, socio-political and environmental problems seem, in part, to be the cause. However, the intangible and qualitative nature of these problems means overcoming them will require a greater systemic understanding of how the various technical and non-technical factors interact. This is particularly important as the concept of sustainable development has changed the industry paradigm sufficiently that it is no longer clear what world-class means. Finally, this better systemic understanding of mine projects needs communicating back to the exploration sector to improve exploration targeting.However, a disconnect between the exploration and mining sectors and between geologists and mining’s other professional disciplines means this is currently not possible. The use of economic evaluation techniques to assess the risk and value presented by the various technical and non-technical factors can assist with this by giving the varied professions a common language and including inputs from all disciplines. This paper therefore suggests a theoretical framework for analysing the various technical and non-technical factors, particularly the most challenging intangible and qualitative ones, and incorporating them into the typical economic evaluation techniques used in the mining industry.Understanding the risk and value relating to both technical and non-technical risks, however, places a greater emphasis on mining geologists to be conversant with a wide range of disciplines. Mining geologists will have to develop three types of knowledge:focusedinter-disciplinarybroad. In addition, they will have to become systemic thinkers to connect these types of knowledge. This multidisciplinary approach will require the use of fundamental critical thinking skills, common sense, intuition, experience and quantitative modelling techniques, dependent on the situation. As a result, both companies and professional societies, such as the Australasian Institute of Mining and Metallurgy, will have to develop ways of improving mining geologists’ inter-disciplinary and broad knowledge.CITATION:Sykes, J P and Trench, A, 2014. Resources versus reserves – towards a systems-based understanding of exploration and mine project development and the role of the mining geologist, in Proceedings Ninth International Mining Geology Conference 2014 , pp 243–270 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 18, 2014

By Cowie WJ, Utting BS

The alluvial gold industry of New Zealand is based on the placer deposits in Otago and on the West Coast. Production from these since discovery in the 1850's has been an estimated 480 tonnes (15 million ounces) of gold. Annual output has expanded continuously since 1980 and is expected to be over 2 tonne of gold for 1989.Following a historical review, the characteristics of typical operations, which use hydraulic excavators and mobile trommel units are discussed. Descriptions are then given of alluvial activities in Otago and on the West Coast.

Jan 1, 1990

By D J. Kilkenny, D A. O’Toole, P B. Hills, K L. Seah

An investigation was undertaken to critically analyse the use of fibre reinforced shotcrete (FRS) for a variety of applications in large diameter shafts. Those applications included the use of FRS with or without the addition of subsequent rock bolting in the temporary support cycle prior to the installation of a permanent lining, most likely cast in situ concrete or as the final lining medium.Numerous authors have considered the early re-entry and strength characteristics of FRS in recent years. The current study has investigated the practical application of the recommendations of many leading authors in an endeavour to establish practical and acceptable risk-assessed procedures for the use of FRS for rapid, safe, efficient and cost-effective shaft sinking.Shaft sinking is regarded as a specialist and potentially higher risk activity due to the confined work environment, exposure to ground conditions and a high degree of manual handling associated with getting materials to the sinking face. The use of robotically applied FRS as a primary lining in shaft sinking has significant safety advantages in reducing manual handing associated with mesh safety support and bolting, as well as reducing direct exposure to ground conditions.The study involved both field testing and a literature review. The study established an initial set of criteria for the use of FRS in the development of large diameter shafts and demonstrated a number of scenarios where the technique of robotically applied FRS provided significant safety and cycle time advantages. The opportunity for a fully sprayed single pass lining was also investigated as part of the project.CITATION:Hills, P B, O’Toole, D A, Kilkenny, D J and Seah, K L, 2014. Exploring the use of fibre reinforced shotcrete in large diameter shafts, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 295–306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By A Dennis, T Hunter, R Coleman

For metallurgical plant design, it is necessary to progress through successive phases of test work, piloting and process development before involving all the other engineering disciplines and “freezing” the process design criteria and flow sheet. This process usually relies upon the experience, skills and personal preferences of various technology providers, study and engineering entities, test work and metallurgical laboratories and, most importantly, the owner’s team and its operators. Current industry trends include lower grades, more complex orebodies, geometallurgy in defining orebody variation and design envelopes, more common “hybrid” plant processes and the market demands for more reliable, timely and predictable early plant performance.This paper will discuss interaction of these trends and provide guidelines for the level of detail and technical complexity required for a number of different “typical” examples. The paper will pay particular attention to the study definition level translated into the required detail and certainty needed by the overall process “owner” and original equipment manufacturer (OEM) equipment suppliers to ensure the best real plant performance. Some recent case studies will be discussed. In many projects, at a late stage of project definition, it has become common practice to undertake a “value engineering” phase. Although it could be argued that this should be undertaken earlier, it is largely driven by an overall need to reduce capex and “optimise” the perceived “fat” built into the project during the detailed design process. This value engineering can be very counterproductive to project timing and operational performance and warrants discussion.The paper is intended to promote discussion on a topic of wide interest. The authors’ diverse backgrounds and experiences are integral to the views in this paper.CITATION:Dennis, A, Coleman, R and Hunter, T, 2017. Critical process design considerations from test work to operations, in Proceedings MetPlant 2017, pp 12–30 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

Direct measurements of liquid contents in foams obtained from (x-terpineol a-T) n-pentanol (AmOH) and n-octanol (OctOH) solutions were carried out using a column of special construction. The column enables to determine the liquid contents by cutting-off foam layers of various thicknesses and measuring amounts of liquid contained in the cut-off foam layers. Liquid contents in the whole foam layers, in the top foam layers of thickness 14 ¦ 1 mm and distribution of water alongside foam height were determined. The average liquid contents were high and reached a level of 30, 35 and 40 per cent for foams formed from cc-T, AmOH and OctOH solutions, respectively. The liquid contents in the top foam layers were much smaller. They were of an order of five per cent for a-T and AmOH and 12 per cent for OctOH. On the basis of the liquid distribution alongside foam height some practical conclusions concerning possibilities of minimising amounts of liquid contained in the collected concentrate are presented.

Jan 1, 1993

By D Mcleod, S Brindley, S Green

The design and engineering of flotation circuits is driven by numerous inputs, including (in no particular order) testwork outcomes, site considerations, type of separation required, energy sensitivity of the flotation response, personal experience and preference for flotation machines, maintenance access requirements, operability, level of automation and capital constraints.This paper discusses these and other issues in the Australian context and covers the flotation of copper/gold ores and polymetallic (copper/lead/zinc) ores. The paper discusses aspects of the following: how should testwork be done and what are the important inputs and outcomes? how should testwork results be interpreted and how does this impact on equipment selection? what processes can have a critical impact on flotation circuit performance, eg thickening and regrind? what options are available with the typical æflatÆ Australia site? how do you minimise capital cost and what impact can this have on flotation circuit operation and maintenance? how should circuits be controlled and operated? Particular focus is placed on some practical aspects of process design and engineering and the potential impact that engineering decisions can have on flotation plant operation.

Jan 1, 2005

The sole reason for a mine to exist is to extract the finite mineral resource. Accurate grade control is critical to the economics of any mine. If grade control is not optimised, then no matter how good the downstream processes are, the full potential of the operation will not be realised. The detailed implementation of grade control varies but typically consists of sampling and assaying to determine the location of the ore zones. A lot of time, money and effort are spent defining the location of the ore as accurately as possible à but then it is blown up! The effect that blasting has on grade control is rarely adequately accounted for when the rock is excavated because there has never been an accurate and practical method for measuring blast movement. This paper draws on over six years of research into measuring and understanding blast movement, which started at the Julius Kruttschnitt Mineral Research Centre (JKMRC) of the University of Queensland. The research has made a unique contribution to open pit blasting by helping to develop a practical tool for measuring blast movement, which was then used to improve the understanding of three-dimensional blast movement dynamics. However, these achievements would be of largely academic interest without taking the final step of using this technology and knowledge to account for blast movement by translating the ore polygons in response to the measured movement vectors. This paper provides an overview of blast movement but focuses on one site where blast movement was measured during three separate periods, with significantly different orientation of the mineralisation on each occasion. The theoretical ore loss varied from nine per cent to 24 per cent. The differences are primarily due to the orientation of the ore polygons relative to the direction of movement. The optimum grade control solution is a combination of accurately accounting for blast movement and designing appropriate blasts.

Jan 1, 2009

By Just GD, Phillips R

The application of high pressure water jet technology to the drilling of longholes in coal has resulted in the development of a system currently capable of drilling to lengths greater than 200m. Field tests at the German Creek Mine have demonstrated directional control of the holes within a 0.5m section of the seam. Initial application of the technique at the German Creek operations is for drilling methane drainage holes. These developments, in three stages, result from support by the National Energy Research Development and Demonstration Council

Jan 1, 1991

By J Tiihonen, J OÆCallaghan, T Haakana

Outotec is today capable of providing technologies, process equipment and engineering for the construction of pressure oxidation leaching (POX) plants in any location in the world. Outotec works with customers from mine to pure metal, participating in plant design from the process development phase (including test work execution/supervision) to plant commissioning and operations. Either key equipment technology packages with basic engineering or entire POX plants can be supplied.The addition of pressure oxidation equipment to OutotecÆs product portfolio adds to and complements already existing significant experience in general hydrometallurgical process and proprietary equipment design and supply.In addition to providing key pressure vessels, piping and valves to a POX plant, Outotec can offer an enhanced and proven autoclave agitation system that maximises oxygen mass transfer and utilisation. Novel energy and water recovery technology can also be tailored to a customerÆs specific needs. Importantly Outotec owns and operates extensive test work facilities and can provide test work to ensure the optimum POX flow sheet and materials of construction. Outotec ensures that best available technology (BAT) concepts are used in POX design to improve the availability of the process and minimise unpredicted shutdowns.CITATION:Tiihonen, J, Haakana, T and OÆCallaghan, J, 2013. Outotec pressure oxidation - more out of sulfide ore, in Proceedings World Gold 2013 , pp 197-206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Grady PO

The longwall panels at Clarence Colliery have experienced intermittent sudden weightings on the face that have caused some production delays. These weightings have typically been more severe on the wider faces. A program of surface subsidence and extensometer monitoring was undertaken above Longwalls 4 and 5 to investigate the behaviour of the overburden strata during longwall extraction on two faces of different widths.The monitoring indicated that a dome shaped zone of large downward movement extends up into the overburden strata to a height equal to about the panel width.

Jan 1, 1998

By L D. Munro, S A. Jackson

This paper provides a logical approach to developing a TSF design concept through: • Identifying key properties of tailings and containment structures; • Reviewing underlying principles for effective operation; • Showing how these apply to select an appropriate TMS; and • Demonstrating how to align the TMS to site-specific constraints and TSF design. This approach follows a path of rigorous data analysis independent of discharge parameters (whether low-density slurry, paste or cake disposal) to select the most cost-effective and sustainable approach for any given material or site.

Jul 1, 2021

By S Bright, M J. Masamvu, E K. Chiwandika, S Dandi, S M. Masuka

The depletion of high-grade hard and lumpy chrome ores has forced Zimbabwean ferrochrome producers to resort to low-grade friable ores that have an average of 28 per cent fines against a set limit of 12 per cent. Submerged open arc furnaces currently in use are associated with eruptions within the furnace because of the high amounts of fines, high energy consumption, as well as high SO2 and CO2 emissions. Traditionally employed agglomeration methods such as pelletising and the use of coke in the furnace have been discarded because of the pressure to lower operational costs and to achieve higher profit margins. This research aims to develop a method to incorporate lowgrade friable ore fines and unprocessed coal into production while lowering CO2 and SO2 emissions through a closed direct current (DC) arc furnace. The closed DC arc furnace could incorporate the friable ores and coal while maintaining above 90 per cent reduction rates. Preliminary findings also show that energy consumption could be reduced by up to 35 per cent by incorporating a pre-heating and pre-reduction system using the flue gases from the furnace. In the proposed circuit, the cost of production per ton of ferrochrome might be potentially lowered by an average of 30 per cent.

Jun 19, 2024

By C Simpson

In 2011 the forecasted world demand for iron ore continues to grow, and during this time Australia is looked upon as a reliable supplier of high quality ore. The expansion of the current Australian mines is unlikely to meet the forecast demand. New mines are therefore being actively explored for and when discovered, are quickly being developed into mines in order to meet the world’s hunger for steel.The Solomon Project area is a large new iron ore discovery, located in the central Hamersley Ranges of the Pilbara province in Western Australia. The first Fortescue exploration drill holes commenced on the project in 2007 and to date three billion tonnes (Bt) of iron ore have been defi ned within the project area. Fortescue is fast-tracking the development of the ‘Solomon Stage 1’ project, with rail and mine construction commencing during 2011, and ore to be railed to Fortescue’s existing shipping operations at Port Hedland commencing in 2012. At a designed production rate of 60 Mt/a, the Solomon operation will be one of the biggest production centres of iron ore in the Pilbara.Deposit types include the three dominant mineralisation styles of the Pilbara province, being bedded iron deposits (BID), Channel iron deposits (CID) and detrital iron deposits (DID). All these mineralisation styles are present in large concentrations within the Solomon project area, and when mined will produce two product streams. These are a single product of CID, and a combined product from a blend of BID and DID material.This paper defines the geological characteristics of the Solomon iron deposits as recognised through the exploration and development of this vast resource over the three years since exploration commenced on the project.

Jul 11, 2011

By H M. Parker, G Verly, T Postolski

Assessing the uncertainty and risk in mineral resource estimation is required for best practice and is implied by the public reporting codes in the categorisation of mineral resources and reserves. One industry best practice is quantifying the risk on future production for a given period, which can be done using two geostatistical approaches: conditional simulation and drill hole spacing studies based on estimation variances. Conditional simulation can provide a more complete and flexible answer to the problem, but it takes a fair amount of time to complete. Drill hole spacing studies are simpler, faster and can provide reasonable assessments of mineral resource uncertainty.This paper is a presentation of the principles, theory and practice of drill hole spacing studies. Various types of risk assessment are considered. Difficulties encountered in practice are discussed, and solutions are proposed. The important parameters impacting the results are reviewed. Examples of results and sensitivities are shown.CITATION:Verly, G, Postolski, T and Parker, H M, 2014. Assessing uncertainty with drill hole spacing studies – applications to mineral resources, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 109–118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By R Schmitt, Y Ghorbani, I McElroy, N J. Bolin, M Parian

Aitik is a large copper porphyry type deposit located in northern Sweden, currently exploited at an annual rate of approximately 45 Mt. The ore’s exceptionally low head grade of 0.25 per cent Cu and varying degrees of hardness across the entire deposit pose challenges to the two fully autogenous grinding lines, each of which comprises a primary autogenous mill in series with a pebble mill. The variability in ore grindability frequently leads to fluctuations in mill throughput. Within the framework of a geometallurgical approach, the present study investigated the relationships between ore grindability and modal mineralogy. For this purpose, drill core samples from different lithologies were subjected to Boliden AB’s in-house grindability tests. This fully autogenous laboratory-scale test generates a grindability index mainly related to abrasion breakage, which is a significant breakage mechanism within autogenous mills. The test results suggested divergent degrees of grindability within and across the selected rock types. A combination of scanning electron microscopy, X-ray powder diffraction, and X-ray fluorescence analyses was performed for the grinding products and bulk mineral samples. The resulting mineralogical and elemental properties were subsequently correlated to the parameters from the grindability tests. It was shown that the main mineral phases, such as plagioclase, quartz, and micas, correlate well with the grindability indices. Similar correlations were found regarding the sample’s chemical composition, attributable to the main mineral phases. A further inverse correlation was established between the sample’s calculated average Mohs hardness and the grindability indices. Moreover, mineral liberation information provided by scanning electron microscopy was associated with the parameters mentioned earlier. The identified relationships between grindability, modal mineralogy, and element grades may help Boliden develop a predictive throughput model for Aitik based on the mine’s block model.

Aug 24, 2022

By Jin C, Shi X

The electrochemistry of leaching gold with thiosulphate has been studied systematically by using electrochemical techniques. Results show that the current peak of anodic dissolution of gold occurs at about 50 mV(SCE) and there is passivation in the polarisation curve in the thiosulphate solution in the absence of ammonia. Ammonia markedly improves the anodic dissolution rate of gold and reduces the passivation as well as making the current peak shift negatively. Results also show that there is no current peak for a cathodic process in the range of 0 -900 mV(SCE) in the thiosulphate solution in the presence of oxygen but absence of cupric ions and ammonia. In the solution containing 0. 1 mol/L cupric-ammonia ions, the peak occurs at about -400 mV (SCE) and the cathodic process is characteristic of a catalytic reaction. Oxygen presents a predominate effect on the cathodic process. Based on the electrochemical investigation, the following mechanism of leaching gold with ammoniacal thiosulphate has been proposed. Ammonia reacts primarily with gold ions on th anodic surface of gold and the formed A (NH3)2+ rea~s then with S2O 3 in solution to form the stabler Au(S203) 2 . Cu (NHS) 4 gains electrons on the cathodic surface and is reduced to CU(N) ? which is then oxidised by oxygen and regenerated into Cu(NH3) 4 after entering the solution.

Jan 1, 1993