Search Documents

The St George orebodies are situated within the tectonically disrupted eastern limb of the Boogardie Syncline.Highly disturbed rafts of banded chert formations occur within a sequence of felsic volcanic tuffs. The chert forms the hostrock for the gold mineralization.The gold distribution within the irregular and narrow banded chert formations is erratic and patchy. The average gold content of the two orebodies is between 3 - 4 g/t Au.Economic mining of these relative small, irregular and low grade St. George orebodies can be carried out by using a highly selective mining method.The highly selective mining method uses an excavator as the principle mining tool. Blasting, breaking and loading of the rocks is done in a different way than by using a front-end loader as with the conventional mining method. Simple, and therefore cheaper, blasting breaks the rocks and lifts them up without major displacements.

Jan 1, 1984

The effectiveness of three different types of longwall chock under the three different types of geological conditions worked recently is outlined. Some provisional analyses of the variation of chock load under the shale roof con- dition are briefly discussed and some problems and solutions of gateway and road- head support outlined.

Jan 1, 1974

Gold mineralisation at the Enterprise Mine, 230 km south of Darwin, occurs within folded and metamorphosed sediments of the Lower Proterozoic Burrell Creek Formation adjacent to the Cullen Granite. The mineralised zone, which occupies an area of approximately 800 m x 300 m is local- ised by a moderately tight, upright symmetrical anticline which plunges shallowly southwards. The anticline has been disrupted by numerous faults on which the maximum movement is 40 m. Gold is associated with quartz and sul- phide veins which are present as saddle reefs, inter-reef veins and fault controlled reefs. it occurs within the veins or their alteration haloes, either as free gold (2 - 50 per cent of total gold content) or intimately associated with sulphides, principally arsenopyrite and Pyrrhotite.

Jan 1, 1984

By Hagan T. O

The problem of rockbursts presents a serious threat to many deep, hard-rock mines. For several decades, the owners and managers of affected mines have been concious of the urgent need to control rockbursts but, to a large extent, their efforts have been hampered by a lack of fundamental knowledge. This paper will attempt to outline the extent and depth of present understanding of the phenomenon and to show how better control may be achieved in the future. It is suggested that it is helpful to distinguish two aspects of the problem: that pertaining to the mechanism of the seismic event and that associated with the mechanism of damage. Understanding damage mechanism will enable development of better support techniques while proper understanding of the source mechanism could lead to better mine planning and improved stoping layouts. In this regard, the practice of partial extraction with systematic strike stabilising pillars is discussed in some detail.

Jan 1, 1986

Techniques and results achieved during the excavation of the Melbourne Underground Rail Loop (HURL) are summarised and discussed in the context of the various restraints present in a typical urban construction project. Mechanical methods (as distinct from those utilising blasting)accounted for the bulk of the excavation. Ground support was critical in this particular geological excavation setting, but is not discussed in detail except insofar as it constitutes a restraint to excavation progress.

Jan 1, 1978

By Johnson MT

The microprocessor revolution of the 1970's dramatically improved the price/per- formance of graphics hardware. Together with improved communications and new software concepts and standards this has resulted in the emergence of a new tool with particular application to the mining industry. The Distributed Graphics Processor (DGP) offers more natural means of interaction with com- plex technical models.

Jan 1, 1983

Backfil ling of excavated Sub Level Open Stopes has been underway since March 1989 and as at December 1992 some 1 100 000 cubic metres of Cemented Aggregate Fill have been placed. During these three years significant developments in fill quantities, types and cost have taken place.Operational improvements have reduced the quantity of Cement Aggregate Fill by 40 per cent. These results have been achieved by:ò rescheduling stopes,ò designing smaller primary stope, and ò use of uncemented rockfill.Unit cost for Cement Aggregate Fill have fallen in the order of 50 per cent through:improving fill hole reli ability,simplified barricade construction procedures, reducing the cement content,ò substituting dune sand for deslimed mill tailings, ò improved maintenance at the Backfill plant, and ò renegotiated site freight agreement.This paper will review the historical developments of backfill use at Olympic Dam.

Jan 1, 1993

The deep seafloor in Papua New Guinea's proposed Exclusive Economic Zone appears to be a gold-rich province in the same sense as the territory above sea level. Two significant sites with polymetallic massive sulphide deposits forming today are known on neovolcanic ridges in the Manus Basin. Their high precious metal contents have led to renewed interest in the issue of exploiting seafloor mineral deposits. The prospects of finding other, possibly larger deposits in the region appear substantial. This paper reviews current data on seafloor deposits in Papua New Guinea (PNG) and raises some issues relating to future commercial exploration and mining of the sea floor. One of the known PNG deposits could become a prime candidate for the trials needed to develop technology, establish costs, and minimise environmental impact.

Jan 1, 1994

By Mercer J. K

Shaft guide reaetions in No. 2 Ore Shaft, Mount Isa Mines Limited, have been reduced to a low order of magnitude by the use of self aligning slippers and spring loaded guide rollers. Before commissioning the new 4500 h.p. winder at No. 2 Ore Shaft in January, 1958, it was realised that the increase in hoisting speed from 1800 to 2650 ft/min. would cause high shaft guide reactions which would be increased further when the elongated 12 ton skips replaced the existing 7 ton skips.The Cambridge accelerometer was used to measure the shaft guide reactions and to confirm that progressive skip modifications were resulting in reduced reactions. The skip modifications were completed in 4 weeks.INTRODUCTIONIn 1956 an expansion programme was initiated to increase production from 5000 to 11000 tons per mining day. At No. 2 Ore Shaft the 1500 h.p. winder operated at 1800 ft./min. and hoisted a 7 ton capacity skip. The new 4500 h.p. winder operates at 2650 ft./min. and hoists a 12 ton capacity skip. No. 2 Ore shaft is equipped with two 5 ft. by 5 ft. hoisting compartments (Fig. 1) and any increase in skip capacity meant an abnormally long skip. This feature, coupled with the increase in hoisting speed, could have caused very high shaft guide reactions. Before commissioning the 4500 h.p. winder, a Cambridge accelerometer was borrowed from the University of Adelaide and was used to measure the shaft guide reactions. Rather than carry out an extensive shaft timbering programme, the skips were modified by fitting cushioned guide shoes and spring loaded guide rollers (Fig. 1). Testing commenced in February, 1958, and was completed in March, 1958.

Jan 1, 1961

By Miller JD, Ye Y

The Air-Sparged Hydrocyclone (ASH) has been developed for the fast and efficient flotation of fine mineral particles in a centrifugal field during the past decade at the University of Utah. Over the years, the air-sparged hydrocyclone unit has shown promising potential for the flotation of copper porphyry ore, low-grade placer gold and auriferous pyrite ores, various industrial minerals, and fine coal cleaning. Many fundamental studies including the X-ray computed tomography (CT) analysis have been carried out in order to understand the multiphase fluid flow phenomena associated with ASH flotation. With data available from these studies, it is now possible to construct more accurate ASH flotation models for different applications in order to analyse the behaviour of the system and to optimise design and operating variables. The ASH flotation model developed in this paper is based on the data given in `Air-Sparged Hydrocyclone/Advanced Froth Flotation Fine Coal Cleaning', Final Report, DOE Contract No DE-AC-88PC88853, submitted by Pennsylvania Electric Company (PENELEC), December 1989. Data from several hundred experiments with the two-inch ASH-2C air-sparged hydrocyclone (capacity 0.1 - 0.3 tph dry coal) are available from the report and have been used for this analysis. In the past, a preliminary model based on limited data had been developed. The current study, however, emphasises the global behaviour of the ASH system by utilising almost all the data from the report for the purpose of scale-up and industrial application. There are two parts in the current modeling and analysis effort for ASH flotation of fine coal. The first part is the modeling/analysis of dimensionless ratio of overflow opening area to underflow opening area, A*, and the dimensionless ratio of air flowrate to slurry flowrate, Q . The second part involves the modelling/analysis of all other variables in the system and an expert system for operation and control is introduced.

Jan 1, 1993

By Draper J. J, Lang S. C

Regional geological mapping and facies analysis of the Late Devonian to Early Carboniferous Keelbottom Group of the Burdekin Basin have resulted in a depositional model representing six siliciclastic-carbonate facies. The six facies represent alluvial fan, braidplain delta, siliciclastic shoreline, siliciclastic shallow marine, restricted siliciclastic/carbonate shelf, and carbonate shoal depositional environments. These facies are identified in the Star beds which are equated with and included in the Keelbottom Group in this paper. Facies are repeated throughout the Group, as a result of two transgressive-regressive cycles.The first transgression recognised in the Keelbottom Group began in the mid-Famennian, and followed deposition of the Late Devonian Dotswood Group. It was marked by the deposition of Siliciclastic Shoreline facies in the basal Myrtlevale Formation, which was succeeded by Siliciclastic Shallow Marine facies at the peak of the transgression. The return of Siliciclastic Shoreline facies in the upper part of the Myrtlevale Formation marked the onset of the first regression, which resulted in the progradation of Braidplain Delta facies from the northwest of the basin. During the peak of this regression, deposition in the western part of the basin was dominated by Alluvial Fan facies.

Jan 1, 1990

Any future developer of underground mining on the Bendigo goldfield will need to understand the unique geology and gold occurrence of this field. The development and sloping system employed will be primarily designed around these unique features. Modern techniques and equipment used in narrow vein mining will be applicable in this situation.The purpose of this paper is to examine the important geological features of the field as well as the known historical occurrences of the type of gold deposition in the ore bodies. This information will point to a system of development and extraction which will accommodate these features.

Jan 1, 1993

By Turner T. M, Jorgensen F. R A

The tendency of the concentrate to ignite was studied using four techniques, namely, laminar flow furnace, fluid bed, thermal analysis and boat-in-furnace. Exothermic activity occurred at two temperatures: minor activity in the vicinity of 200¦C, major activity at 330-350¦C. The low temperature reaction was due to the ignition of a small amount of free sulphur while the major activity was associated with the ignition of the sulphide minerals, notably pyrite. To avoid ignition of the sulphide minerals, the gas temperature should not exceed 300¦C and the oxygen content of the gas phase should be as low as possible. It was shown that little of the arsenic in the concentrate entered the gas phase during drying.

Jan 1, 1987

By Feilding C

Vitrinite of humic source (often designated as vitrinite A) is the maceral by which the rank of a coal ought to be determined. Therefore its recognition, and the precise identification of other vitrinites is essential. The majority of Australian petrologists are not differentiating between the vitrinite group macerals in maturation studies, the results of which have led to unexplained phenomena in coal characterisations and evaluation, such as 'reactive inertinites' and inaccurate predictions in petroleum source rock studies. The Callide coal has been chosen as a case study, with examples from other coals. The coal seams from the Callide Coal Measures show variation in the predominance of some macerals, indicating successions of environmental changes. The application of transmission electron microscopy (TEM) to the study of the Callide coal has enabled a better understanding of the nature and origin of some of the less understood macerals such as micrinite and vitrinite B. Two forms of vitrinite have been observed, each with a distinct reflectance range. The wood-sourced vitrinite A displays an average reflectance of 0.56 per cent, and a range of 05. - 0.7, implying a higher rank than the 0.49 per cent Ro total vitrinite reflectance recorded in previous publications. Vitrinite B is one of the most commonly-occurring macerals in the Callide coal. The lower-reflecting vitrinite B which forms bands, often several hundred microns in thickness, in TEM appears to be electron transparent lipid rich. Vitrinite B is interpreted to represent accumulations of leaves, and is believed to be a major source of hydrocarbons in Australian sedimentary basins. The Callide coal has entered the oil window, and oil has been generated from some exinite, cutinite, and resinite, as evident from the amber to light brown fluorescence of exinite and the presence of exsudatinite in cell cavities and cleats. However vitrinite B, the major potential source of oil, is seen under the microscope to be generating oil, thus placing this coal at the top of the oil window. Micrinite, the origin of which has been much debated, occurs as cell filling or infill of spaces between laminations in vitrinite B.

Jan 1, 1991

By Hansmire WH

The 14.7 km Mt. MacDonald Tunnel beneath Rogers Pass in Canada used both drill-and-blast and machine boring methods. A unique ventilation system provides for diesel operations. The design featured minimum construction support and an unrei.nforced poured concrete lining. The west heading was excavated in a single-stage drill-and-blast operation. The east heading used a TBM top heading with a drill-and-blast keyhole bench. The choice of methods was controlled by varying geology, with up to 1,700 m rock cover. Construction performance and progress are evaluated.

Jan 1, 1987

By Nguyen G. H, Graham J

A laboratory-scale fluidised-bed roaster has been used to examine the effect of temperature and duration of roast on the morphology of the calcine produced from a pyritic gold-bearing concentrate. Two mechanisms of oxidation, which depend on the roasting temperature, have been identified. For samples roasted below 550°C, direct oxidation of the sulphide occurred to form hematite with a porous fine-grained concentrically-layered texture. The surface area of the calcine increased with an increase in roasting temperature in the range 400 to 500°C. For samples roasted above 550°C, the first reaction was the evolution of sulphur vapour to produce pyrrhotite, which underwent increasing grain growth as the roasting temperature was increased. This had the effect of decreasing the surface area of the calcine. The pyrrhotite was subsequently oxidised to produce hematite.Leaching studies using cyanide solution indicated that gold extraction around 95 per cent was achieved at temperatures of 500°C and above, with optimum extraction, taking into account rate and cyanide consumption in the range 550 - 700°C. Hence recovery did not decrease with decrease in surface area of the calcine. Observed gold in leached calcines was mainly enclosed in thin oxide walls of the hematite, with minor quantities enclosed in quartz and silicate minerals.

Jan 1, 1995

By Forsythe DJ, Sun S-S Andrew AS

Paragenetic, fluid inclusion, stable isotope, and 87Sr/86Sr and 143Nd/144Nd isotope studies of the Mt Carbine tungsten deposit in North Queensland provide information on the sources of the mineralising components and record the history of fluid-rock interaction during the hydrothermal process. The ore minerals , wolframite and scheelite , are contained in quartz veins which post-date the major deformations in the Siluro-Devonian Hodgkinson Formation . Mineralisation was immediately preceded by the emplacement of the Mossman Batholith (280 ¦ 7 Ma). Two major stages of mineralisation are present and separated by a brittle fracturing episode . The stable isotope and Sr and Nd isotope data suggest that the ore fluids during stage I and most of stage II mineralisation were a mixture of magmatic water and non-magmatic water (connate or metamorphic) which had experienced a long residence time and had extensively exchanged with the sediments at high temperature. Subsequent mineralisation events were dominated by fluids of meteoric derivation with a short residence time. The data imply that other solutes, such as W, were probably derived in minor part from local country rock sources with the major contribution coming from a magmatic source related to the granite batholith.

Jan 1, 1987

By M Wortley, J McKay, D La Rosa, O Guyo

It has been a generally held concept that crushing operations were, by their nature, too simple to benefit from the implementation of advanced process control. The commissioning of an OCS¬ expert control system and image-based oversize detection system, VisioRock, at the Pilbara Iron Tom Price facility are dispelling these notions. A constraint-based OCS¬ expert control system has been designed and commissioned on the high-grade crushing and screening plant along with a vision-based oversize detection system functioning on six product conveyor belts. To date, the expert control has demonstrated the ability to increase production by maximising dynamic constraint utilisation. Dynamic constraint utilisation is a concept developed by Rio Tinto Technical Services for effectively evaluating constraint-based control logic performance. The VisioRock system has been installed and configured and has been operating for a period of several months. Currently, Tom Price and Metso personnel are working to define correct oversize detection thresholds. Details of the plant implementation are discussed.

Jan 1, 2005

By L Ventura, M Almond

The Pueblo Viejo project in the Dominican Republic installed an innovative sample system on its reverse circulation (RC) drilling rig during commissioning and subsequent commencement of operations. As knowledge of the orebody increased with mining and plant production, cost pressures became apparent that raised questions concerning the continued use of RC drilling versus blasthole sampling for ore control.To justify the continued use of RC drilling for grade control, an in-depth study was undertaken to determine the quality of the sample and prove its value-add to the operation.To investigate the differences in sample quality, a complete bench trial was initiated across both ore pits to compare RC drill results with blasthole assays on a side-by-side basis. The results indicated that based on ore block comparison between RC and blasthole sampling, RC identified an additional 20 per cent of high-grade (+ 4.5 g/t Au) ounces.Previous work indicated that Au, Ag and Cu were all elevated in the drill fines at Pueblo Viejo (Goers and Almond, 2012). This previous test work did not consider the quantity of fines in an RC sample therefore new test work was undertaken to include particle size distribution analyses. This study would determine if the inclusion of fines in the sample was occurring and compare the quantity of fines in the sample against other sample systems and blasthole samples.Comparisons between RC samples and blasthole samples indicate that for the RC samples a range of 30–35 per cent of the sample passed 300 mesh as compared to blastholes where the range of the sample passing 300 mesh was 15–30 per cent.This paper includes a case study on the importance of accurate samples and how they have impacted throughput through the pressure oxidation process plant at Pueblo Viejo. The accurate samples provided by RC allow for improved stockpile and blending strategies, showing the importance of accurate samples to manage risk and create value, against the perception that savings can be made at the risk of poor sampling performance.CITATION:Almond, M and Ventura, L, 2017. Adding value with reverse circulation drilling at Pueblo Viejo, in Proceedings Tenth International Mining Geology Conference 2017, pp 277–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By Lindner E, Bosio M

South Australian coals are all low in rank and generally poor in quality, with difficult combustion characteristics. This circumstance makes the selection of a fuel source for future power generation difficult, requiring careful study and detailed analysis of the various alternatives. Combustion characteristics can have a significant effect on plant design and costs, and need early attention in any exploration and evaluation programme. The physical location of the deposits, often remote from established infrastructure and centres of population, is also a major factor in the ultimate cost of power at the poirl use.

Jan 1, 1977