Search Documents

The B.R.G.M., through international experience gained over many years, has become very skilled in alluvial prospection, particularly for diamonds. The research laboratories within the B.R.G.M. have also been active in creating new mineral processing equipment,. some of which is directly applicable to such prospection. One such development, the mobile prospection unit, is described and -its application in mineral exploration is demonstrated by a consider- ation of the diamond search in Australia and the general exploration of the Massif Armoricain (France). Because this latter study was fundamental in the development of the concept of "mineral-geochemistry", and its application in mineral exploration, it is also briefly described.

Jan 1, 1980

The mmmg of alluvial gold involves many deposits of theMesozoic, Tertiary, and Quaternary Ages in processing. Majorfeatures of the composition of such alluvial deposits are the lowcontent of gold and the small size of the gold particles. Atpresent, the gold-miners treat alluvial deposits in which a portionof fme gold (0.25 mm) exceeds 45 per cent. It is expected that by2000 these resources will be the main deposits mined (Zamyatinet aI, 1991).Under real industrial conditions the losses of minus 0.25 mmmetal are 50 per cent and more. The low level of recovery of finegold is observed not only at concentrators equipped with sluices,but also at concentrators equipped with modern diaphragm andpistonless jigs (Table 1).

Jan 1, 1993

By Hermann J. A

Over the last few years enormous dapooits of high-grade bauxite have been discovered in Australia, ;_ d an alum .nium smelting industry based on them is rapidly being developed,, This industry requires large amounts of carbon, as about 60 pounds of carbon anodes are consumed for every 100 pounds of aiumin.'.'-n produced. Tie anodes are usually made by mixing finely ground petroleum coke with coal tar or petroleum pitch, forming the mix into shapes under pressure, and baking them at around ?.200¦C0 Petroleum coke is ussd uecause its high density gives good strength and conductav_ty to the finished electrode, and its purity ensures that contamination. of the alumin- ium by extraneous i,iorganic material from tho carbon is low,

Jan 1, 1969

Indiscriminate surface disposal of coal waste in New South Wales has created a serious fire hazard and increased air pollution.A survey of numerous dumps, as well as particular investigations of one badly-constructed dump, showed that factors conducive to ignition and propagation of fires in waste dumps were high contents of combustible material (coal, pyrite, wood. paper. grease), size segregation leading to ready movement of air and moisture shape of the dump (e.g. protruding sections or porous junctions), high ambient air temperatures, bush fires, and even deliberate lighting.Control methods applied in the past tended to be haphazard and unsuccessful. Under Australian conditions the technique recommended for control of existing dump fires, based on experimental work, is to spray the dump with a chemical fire retardant (e.g. a 2 per cent solution of sodium tetra borate and ammonium phosphate), to cover the dump with a suitable soil, and to seal the surface with a I per cent solution of aluminium sulphate or sodium metasilicate. The recommended method of dump construction to prevent fires is to level and seal the site, to construct a firebreak around the dump area, and to build a rectangular dump with minimum size segregation and compacted surfaces.

Jan 1, 1971

Drum winders have now been built to attain depths of 3000 m and more in a single lift in accordance with the South African Code of Practice SABS 0294, which was introduced at the time of the last hoisting conference in 2000. Since then, this code has not only been followed for several winders in South Africa but was also followed in deep mines in Canada. Design of winders and their braking systems are described in the paper. Koepe winders are in use for high payloads of up to 50 t and to hoisting depths of around 2100 m. As known, the stress range of the hoisting ropes is the key parameter for rope fatigue. However, as per the SABS Code of Practice 0294, relying on static design is not the answer to the question of where the limits are for Koepe installation. The paper describes factors that are recognised to have influence in rope life and suggests definition of new design criteria for friction winders in order to get viable solutions for high-capacity hoisting from deep mines similar to drum hoisting.

Jan 1, 2005

By Witkowski A

I have the pleasure to present 6 excellent papers in this section all of major relevance to the mining environment of today where competing social, legal and monetary interests and their often complex interaction require serious consideration. This is particularly true today where huge fluctuations in commodity prices makes mining a perilous undertaking while the world increasingly are becoming aware of the serious threat that mans activities has on his environment. The 6 papers deal with such complex issues as safety in an underground environment; How to protect sensitive wetlands well into the next century; The enormeous waterproblems in China and conflicting dewatering/water supply needs; Disposal of contaminated water in sensitive areas and the dynamic interaction between mining companies and legislation.

Jan 1, 1988

By Gray E, Banks J

In mine site revegetation, exotic grasses are more commonly used than native grasses. This is due to unavailability of native grass seed on a commerical scale and lack of information on agronomical aspects of native grasses. This paper lists a number of native grass species that have the potential to grow well on mine sites, and provides some information on their seed collection, processing and germination. Further, it demonstrates via results of a field trial conducted at Ranger Mine spoil the relative performance of ten native grasses and Rhodes grass. It is concluded that (i) some native grasses have similar ability to grow on mine spoils compared to Rhodes grass and (ii) the use of native grasses have added advantages in ecosystem restoration.

Jan 1, 1994

By Amanatidis A

In this paper, the kinetics of iron precipitation as sodium jarosite from aqueous solution is investigated. The determination of the reaction mechanism is attempted based on the experimental data of iron removal as a function of time, without using the characteristics of the precipitate.Experiments at the temperature range from 50° to 95°C were carried out with initial conditions of iron concentration IQ g/L, sodium sulphate concentration 25.44 g/L, sulphuric acid concentration 3.68 g/L, pH = 1.5 and agitation rate 600 rpm. Temperature greatly and positively influences iron precipitation from the solution and this is accompanied by pH decrease. The activation energy was determined using the maximum values of the precipitation rate, which were evaluated by polynomial fitting of the sigmoidal shape experimental curves, and it was found to be 44.37 kcallmole. The determination of the rate-controll ing mechanism was based on some criteria used for the discrimination among the three probable mechanisms of precipitation (diffusion, mononuclear nucleation, polynuclear nucleation). These criteria utilise various funetions of the recovery 'a' of iron precipitated versus time, the most important of which are the chronomals. The results of the kinetic analysis procedure showed that the polynuclear nucleation growth mechanism controls the precipitation of iron as sodium jarosite. This was confirmed by the high value of activation energy, excluding diffusion as the controlling mechanism.

Jan 1, 1993

The Lane Cove Tunnel (LCT) is an important infrastructure link in New South Wales (NSW) and runs from the end of the Gore Hill Freeway at Artarmon at its eastern extremity, to the end of the M2 at North Ryde at its western extremity.  The LCT is 3.6 km long and generally consists of twin two/three lane unidirectional tunnels running largely under Epping Road from just east of Mowbray Road, west to the western end of the Gore Hill Freeway. The tunnel opened in early 2007. The presentation will provide a summary of the traffic and emission modelling performed for selected representative surface road sections in the vicinity of the Lane Cove Tunnel. An assessment of the predicted impact of vehicle emissions on ambient air quality in the corridor as a result of changed traffic conditions due to the tunnel opening will be presented. The traffic modelling and emission calculations were undertaken for the following two scenarios: Year 2006 û Lane Cove Tunnel no-build option, and Year 2006 û Lane Cove Tunnel build option. Vehicle emission calculations for the four main pollutants from vehicles: CO, VOC, NOx and PM10 on the surface roads in the vicinity of the Lane Cove Tunnel were performed using the predicted daily traffic for the two cases (no-build and build). The analyses indicated that the vehicle emissions for all pollutants are expected to significantly reduce in the corridor with the building of the Lane Cove Tunnel, including the areas in the vicinity of all tunnel portals, when compared to vehicle emissions for the no-build case.  As a result of the decreased vehicle emissions on the surface roads, the study concluded that the actual ambient air quality is expected to improve in the corridor including the tunnel portal areas after the Lane Cove Tunnel opening.

Jan 1, 2008

The Snap Lake Phase I project initiated a subsampling campaign on the material (kimberlite/metavolcanic/granite) mined and treated for diamonds. The campaign was aimed at determining the optimum subsampling program to subsample the feed to the bulk sample plant (BSP) for the duration of a sampling campaign. This paper describes the application of GyÆs formula for determining the subsample size and other good sampling practices to determine this subsampling campaign. Three main issues are discussed: the use of a hammer sampler to sample off a moving conveyor and the practical experiment to determine the optimum subsampling program; bias introduced by laboratory equipment including two sizes rotary splitters; and variability of the feed material to the BSP over time.

Jan 1, 2005

Exploration for uranium in Australia commenced only during the 1940s, but in this short period has been very successful as one third of the world's low cost uranium reserves have been discovered in Australia. Total uranium exploration expenditure in Australia up to the end of 1983 was $A(1983) 554 million; this discovered 20 potentially economic deposits and official reserves of 560 000 tonnes of uranium oxide at an average cost of $1 per kg of U 0 . An exponential 8 eserves indicates distribution of uranium r that there could be 54 undiscovered uranium deposits in Australia, each with reserves of 20 000 tonnes U308 or more, in addition to smaller deposits. Using a constant uranium price of $A(1983) 79 per kg, no deposit is economic at a grade below 0.12 per cent U 08 or with reserves of less than 3 000 tonnes. Selecting deposits with reserves of 5 000 tonnes U 0g or more as prime exploration targets, only 39 per cent of discoveries will yield a real internal rate of return (IRR) of 10 per cent or more. After committing a minimum exploration budget of $10 million to this search, an explorer has one chance between 7 and 12 of discovering a deposit that will repay the exploration investment.

Jan 1, 1984

The man in the street (and no doubt most members of the Institute) thinks of wire, if he gives it any thought at all, as a most commonplace commodity. It is an accepted necessity, and like most necessities is taken for granted, unless a shortage in one or other of its multitudinous forms or products causes inconvenience.For many years Australia has ·been a large consumer of wire, particularly for fencing. With the rapid development of secondary industry the demand has increased in both size and character until at the present time much of the wire produced in this country is used as raw material for subsequent manufacturing processes. The call has been of so varied a nature that the Newcastle Wire Mills now turn out a greater variety of wire types than any other single plant in the world.In this paper, the aim is to provide a picture of the manufacturing, properties, and uses of wire. No attempt is made to cover the subject in any detail, as the field is much too broad for anything other than general treatment. Many phases, particularly in regard to manufacturing processes, are, therefore, dealt with cursorily, but it is hoped that the paper will, without delving too deeply into the technical aspects of Wire production, give a general appreciation of:- (a) How steel wire is made. (b) The remarkable physical characteristics obtained by judicious combination of chemical composition, heat treatment, and subsequent cold work. (c) The uses of steel wire.HISTORY.Best known of the early references to wire is that appearing in Exodus, where mention is made of gold wire being used for the sacerdotal robes of Aaron. However, the period in question, about B.O. 1491, is comparatively modern history as far as wire is concerned, for specimens believed to have been made about B.O. 4600 have been found. It is fairly certain that the Egyptians produced iron wire in B.O. 4000. Of particular interest is the

Jan 1, 1947

By Amos QG

The Paddington I and proposed Paddington II Pits are both located in what is, by Eastern Goldfields standards, a large tonnage-low grade orebody. The Pits have been designed to supply ore to a substantial Treatment Plant at the designed rate of 875,000 tpa. (This throughput is currently being increased to 1,200,000 tpa).Generally the orebody lends itself to large tonnage mining techniques, relying on only a relatively small amount of sampling. The surface enrichment zone and depleted zone are reasonably complex and require more intensive grade control and sampling techniques as typically utilised in many surface mines in the Eastern Goldfields, although as experience and understanding of the nature of the orebody was gained, less sampling became necessary.

Jan 1, 1986

By Cutafani M, Lama R

An approach to combatting abnormal roof control conditions in underground coal mines is outlined. Support techniques available are discussed along with the methods available to be adopted in different situations. Properties of materials available presently are tabulated together with the conditions of their Application.

Jan 1, 1988

By Kolarczyk M

When controlling the ventilation process in a deep mine some knowledge of the sensitivity of the air volume output to changes in the resistances of network side branches is of great advantage.Sensitivity is taken to mean the limit of the differential quotient AV /ART where AV. is the change in air output in the i--h side branch caused by a change of resistance LI R in the r-th side branch. A method Is presen- ted for determining any arbitrary co- lumn of the sensitivity matrix. A network interpretation of this met- hod was developed in which an ancilla- ry network additional the basic network is constructed and solved, giving an analysis of the sensitivity signs de- pending on the structure of the network.

Jan 1, 1988

By Kesser Z, Vincze T

The Western Mining Corporation mining lease on the Bendigo Goldfield measures 5krri x 18km with more than 20 anticlinal folds parallelling th long north-south boundaries. Numerous closely spaced shafts and extensive underground workings on the reef lines along the folds flooded with groundwater following the progressive abandonment of the field. Preliminary water sampling and assessment demonstrated that a major dewatering programme and acceptable disposal methods were necessary to dewater interconnected old workings in areas of interest prior to any underground work taking place. A field wide geohydolic investigation was undertaken to establish geohydraulic parameters, groundwater recharge rates and water qualities. Data from the field investigation together with estimates of the volume geometry of the submerged workings as obtained from old mine plans, production history, and limited pump testing results were used with an appropriate analytical model to obtain estimates of water discharge rates required to reach various dewatering targets. Water disposal options were limited by relatively high salinities, arsenic levels, contained hydrogen sulphide, and the mine locations within the urban areas surrounding Bendigo. Direct disposal to the surface drainage system could not be considered, treatment to acceptable discharge standards was not economically feasible, and it was necessary to adopt a strategy of collection, containment, and evaporation.

Jan 1, 1988

Characterising the weight percentage of each mineral in base metal ores is an integral part of assessing the quality of an ore in terms of its processing properties. The Rietveld method, which uses X-ray diffraction data, has been applied to routinely quantify the minerals in lead/zinc and copper ores from Mount Isa Mines Limited and supergene copper ores from Ernest Henry Mining as well as their related products from the concentrators. The Rietveld method has been tested by comparing Rietveld mineral data with a standard sample with known mineral weight percentages and comparing Rietveld mineral data with mineral data calculated from elemental assays where the element only exists in one mineral such as lead in galena. Where this latter situation does not occur, the Rietveld method has been checked with both elemental and optical microscope data. In all cases, there is a good correspondence between the Rietveld data and the data it was checked against with absolute differences generally in the range of 0.5 to 3 wt per cent. The Rietveld method generally quantifies all minerals occurring over 1 wt per cent in one analysis and is less expensive and more routine compared to traditional methods such as optical microscope point counting. The Rietveld method can be applied to many stages of the mining cycle such as exploration, feasibility studies, mining, minerals processing and for environmental studies.

Jan 1, 1998

The advantages of coordinate geometry in design and construction of underground works are apparent for reasons of flexibility, security, computer operations, survey error analysis, and the use of numerical techniques for setting out and checking works. Integration with National or State survey systems is useful in the long term, both at design, construction and future works stage. Equipment and methods are available which permit "absolute" monitoring of structures and strata over long periods,to close toler- ances. This work can be carried out in the limiting urban environment. Rapid data acquisition by semi-automatic devices, or photogrammetry, utilizing electronic data processing is capital inten- sive, but provides more data than analogue surveys (i.e., setting out centre lines) and becomes more attractive with increased labour Costs.

Jan 1, 1976

By Whitford DJ

A distinct zonation occurs in the nature of submarine volcanic activity associated with westwards propagation of the Woodlark spreading system into continental crust. Olivine tholeiites (Type I MORB) flooring one spreading segment in the Eastern Sector of the Western Woodlark Basin are accompanied by more evolved "ferrobasalts". Basaltic andesites and Mg-poor andesite-dacites occur on axial and flanking seamounts respectively. In the Western Sector, Mg- and K-rich olivine andesites occur in a rift valley and on an axial seamount near the tip of the propMr/8 tig rift. Observed correlations between 6Sr ratios (0.7028-0.7041), REE patterns and K contents imply a complex petro- genesis with the relative importance of mantle heterogeneity and crustal contamination difficult to resolve.

Jan 1, 1987

Blasting is a common practice in mining whereby solid rock is fractured, using explosives, to a more manageable size. The effectiveness of blasting influences a number of downstream activities such as shovel digability, crusher throughput and mill throughput. As the cost of explosives is relatively low compared to milling costs (mainly due to power consumption), blasting practices can be optimised so that the downstream processes are made more efficient, and an overall cost saving made. This is the basis of the Mine to Mill approach. The effectiveness of the blasting is influenced by two main factors, the blasting practices used (eg explosive amount and type) and the geology of the area. As the geology cannot be altered, the blasting practices must be refined to create optimum blasting. Kalgoorlie Consolidated Gold Mines (KCGM) Fimiston operation, located in the heart of the Kalgoorlie Goldfields is the largest gold mine in Australia. Mine to Mill at KCGM has had varied success, with initial positive indications being lessened by a number of factors, including the increase in the amount of voids.

Jan 1, 2003