Search Documents

By David White

THE submission of carefully prepared estimates of the oil reserves of the United States calls for no apology or explanation. In this country, petroleum is a rapidly wasting asset and an occasional appraisal of the amount remaining in the ground is a simple business procedure to safe-guard the general welfare and the prosperity of the republic. The rumored danger of failure, in the near future, of the foreign supply on which we depend in constantly increasing amounts makes the immediate review of our available reserves the more imperative. The Director of the U. S. Geological Survey, in March, 1921, requested the American Association of Petroleum Geologists to cooperate in the preparation of new estimates of the oil remaining in the ground. With the members of this cooperative committee, state geologists, regional geologists, consulting specialists, and geologists and engineers attached to many companies worked both independently and through sub-committees. The reports for districts, counties, fields, etc., after review by local or state committees, were discussed by the joint cooperative committee in conferences that, in some instances, were attended by the original compilers of estimates for the states or smaller areas. Finally the data were reviewed and the figures revised by the joint cooperative committee, so that the totals given in Table 1 represent the opinion of the committee, which was composed of F. W. DeWolf, W. E. Wrather, Roswell H. Johnson, Wallace A. Pratt, Alexander W. McCoy, Carl H. Beal, C. T. Lupton, G. C. Matson, K. C. Heald, W. T. Thom, Jr., A. E. Fath, Kirtley F. Mather, R. C. Moore, and David White, chairman.

Jan 6, 1922

By J. Steininger

The Hallimond tube flotation of sphalerite and pyrite with sulfhydryl collectors has been found to be inhibited near neutral pH in the presence of copper salts. Alkalimetric titration studies of the reactions between collector and activator indicate that this effect is apparently related to the formation of basic copper collector complexes. The conditions of formation of these compounds and their stability are in good agreement with the depression observed in flotation experiments. The general procedure employed in the flotation of zinc sulfide minerals requires activation of the mineral surface by heavy metal ions, usually copper, which react more easily than zinc with the common short-chain ionic sulfhydryl collectors.' Commercially, zinc flotation is carried out under alkaline conditions (pH 7 to 10.5), but small-scale experiments indicate that zinc sulfide minerals can also be activated and collected under acid conditions. Selectivity, however, becomes poor at low pH and undesirable materials such as pyrite, silicates and carbonates tend to report in the float. Several years ago, Wark and Sutherland~, measured the contact angles of air bubbles on copper-activated sphalerite immersed in various sulfhydryl collector solutions. When represented, as in Fig. 1, on pH-sodium cyanide diagrams, the results are characterized by 'islands' of non-contact near neutral pH and

Jan 1, 1969

By Murray Kaufman

Using en; 41 for a base alloy, 15 modifications were made in sheet form. The elements Al, Ti, C, Mo, Co, and Cb were varied. The effects on the phases formed and their temperature dependence, the aging characteristics, tensile and stress-rup- ture properties, and weld cracking were determined. The A1-Ti content and balance is the most important factor influencing the major sCrengthening phases [Ni,Ti and Ni,(Al, Ti)] and, consequently, mechanical properties. THE mechanical properties, fabricating and joining characteristics, dimensional stability, and so forth, of alloys containing secondary phases are largely determined by the phases present, their distribution, and their temperature dependence. The phases in the basic ternary and quaternary Ni-Cr-Al-Ti combina- tions have been investigated thoroughly.'* The phase behavior of many commercial nickel-base alloys has been determined also. In some cases, for example U500, 5 the effect on mechanical properties has been found. However, little systematic work has been done to clarify the action of each of the important alloying elements in controlling the phases formed in complex commercial alloys and their behavior. The effect of molybdenum on the carbides formed in M252 was investigated by Beattie and verSnyder.6 Application of the results provided by that work

Jan 1, 1963

By H. G. Papacharalambous, S. C. Sun

Experimental results indicate that wet cyclones could be effectively used for the preliminary classification of the tested synthetic abrasive materials, thus supplementing the currently used sedimentation method. An empirical formula is also proposed on the basis of the test data to calculate the particle size of separation. One of the basic operations in the abrasive industry is the classification of the crushed and ground materials into different sized products. The relatively coarse grains, plus 325 mesh, are commonly sized by dry screening with satisfactory results. On the other hand, however, the currently used grading tank, for classifying grains finer than 325 mesh, is intermittent. Consequently, it is difficult to operate efficiently and keep pace with erratic market requirements. Little success was made in an attempt to substitute air settling and continuous hydraulic settling for the grading tank, because size specifications1 for abrasive powders are very stringent and difficult to meet. Finally, a wet cyclone was chosen for experimentation. Even though wet cyclones have not been extensively used in the classification of abrasives; however, their performance as a classifier has been verified by Driessen2,4 on coal, McCarrel5 with manganese, and Herkenhoff6,7 on iron ore. Experimental work on silicon carbide, boron carbide, and fused alumina has shown that the cyclone

Jan 1, 1963

By R. W. Borio, T. S. Spicer

Inflammability and crossing point apparatus were used to study the influence of increasing amounts oi such inerts as ash, fly-ash, pyrite, limestone and Portland cement with several pulverized bituminous coals. The results indicate that it requires large proportions of inerts to substantially suppress the ease of ignition. The ignition phase of the combustion of solid fuels has been under study periodically since 1900. With the advent of pulverized coal firing some 60 years ago, a technique now dominating the coal utilization field, the ignitibility characteristics have become increasingly important. Much of the early work was directed toward the prevention of coal dust explosions and improved mine safety rather than combustion. Many factors affecting ignitibility have been studied and numerous methods devised in an effort to measure the ignition temperature and these have been reviewed by other authors. A recent survey was made by Finney and Spicerl in 1959, so a discussion of previous work will be omitted. Despite these efforts, the initial stage of combustion, termed ignitibility, is still a little understood phenomenon. In fact, no ASTM method has been adopted for the calibration of this illusive property. However, a D-5 Subcommittee XVI on Ignitibility of Coal and Coke of ASTM (now inactive) defined ignitibility:' "The ignitibility of a fuel is that char-

Jan 1, 1963

By D. H. Desy, L. C. Fincher

The magnesium-rich end of the Mg-Ti phase diagram was investigated. The liquidus, solidus, and solvus boundaries to 1 pct Ti were established. All alloys were prepared by saturating molten magnesium with titanium in a consumable titanium crucible under inert gas maintained at 230 psig. The liquidus of the Mg- Ti system was determined by analysis of dip samples taken from 700° to 1300°C under equilibrium conditions in a pressurized inert atmosphere furnace and by analysis of small ingots rapidly poured and quenched from 1400° to 1500°C. The solubility of titanium in magnesium ranged from 0.018 wt pet Ti at 700°C (0.012 wt pet at 650°C by extrapolation) to 1.035 wt pet Ti at 1500°C. The solidus for compositions ranging from 0.03 to 1.00 wt pet Ti was determined to be 650° ± 1°C by thermal analysis. The titanium solid solubility values ranged from 0.08 wt pet at 350°C to 0.19 wt pet by extrapolation to 650°C. The freezing reaction is peritectic. No intermetallic compounds were found in the system; the phase in equilibrium with molten magnesium saturated with titanium was found to be titanium with magnesium in solid solution. Solid titanium will dissolve at least 1.32 wt pct Mg. PREVIOUS investigations of the Mg-Ti system have shown considerable disagreement on the solubility of titanium in liquid magnesium. Furthermore, the solid solubility of titanium in magnesium has not been well established. Liquidus curves for previous work and for the present investigation are shown in Fig. 1. Aust and Pidgeon1 used a dip-sampling method on molten magnesium held in equilibrium with solid titanium under a protective atmosphere to determine the solubility and found that it ranged from 0.0025 wt pet Ti at 651°C to 0.015 wt pet Ti at 850°C. Eisenreich2 introduced titanium into molten magnesium by means of TiCL4 adsorbed on BaCl2. Ingots were then cast at various temperatures. Making the assumption that only the titanium dissolved in magnesium at the time of casting was soluble in H2SO4, Eisenreich determined the solubility of titanium in molten magnesium to range from 0.003 wt pet at 655°C to 0.115 wt pet at 800°C. Eisenreich also determined the solid solubility of titanium in magnesium to be 0.015 wt pet at room temperature and 0.045 wt pet at 500°C. Since the solid solubility just below the freezing temperature for the bulk of the alloy was much larger than the liquid solubility just above the freezing temperature, Eisenreich concluded that the freezing reaction was peritectic. Obinata et al.3 equilibrated molten magnesium with titanium in hermetically sealed titanium containers which were then furnace-cooled. The titanium content of the magnesium was then determined and found to range from 0.170 wt pet at 700°C to 0.85 wt pet at 1200°C. No intermetallic compound was found in the system. The Armour Research Foundation4 determined two points on the solvus by electrical resistivity methods: 0.00057 wt pet at 200°C and 0.0008 wt pet at 300°C. At higher temperatures, data were meaningless with no trends observable. The authors of this report believed that the lack of significant data at the higher temperatures was due to variations in specimen geometry, although there was no positive evidence to verify this supposition. The present investigation was undertaken to clarify the uncertainty in both the liquidus and solvus of the magnesium-rich end of the Mg-Ti system. EQUIPMENT AND MATERIALS The equipment used in this investigation, with some modifications, was essentially that used by Crosby and Fowler5 in their determination of part of the Mg-Zr phase diagram. The equipment, as modified for this work, is shown in Fig. 2. It consists of a sealed furnace chamber which can be pressurized with inert gas so that melts can be made above the boiling point of magnesium at atmospheric pressure. Melts are made by induction heating in a titanium crucible which, after diffusion of sufficient magnesium into the walls of the crucible to saturate the titanium at the sampling temperature, comprises the solid phase in equilibrium with the molten magnesium. Dip samples may be taken with the sampling tube, or the entire furnace may be tilted so that ingots may be poured into a mold in the side chamber. The principal difference from the earlier apparatus is in the thermocouple, which in the present equipment is enclosed in a protection tube and immersed directly in the melt. The tips of both the thermocouple protection tube and the sampling tube, which dip into the melt, are made of high-purity titanium. The 4 1/2-in.-long titanium tip of the sampling tube is threaded into a steel tube, O in Fig. 2, which extends through the top of the furnace. To determine whether the temperature at the tip of

Jan 1, 1969

By W. H. Emmons

INTRODUCTION THE deposition of metalliferous lode systems takes place at considerable depths and no one may observe the process. We see only the end results of the process and from these we seek to construct a theory that will account for them. Because there is an obvious relation between many lode systems and intrusive igneous masses, it is a natural inference that they have formed by fluids that were expelled from such masses. The metalliferous lode systems have been deposited by ascending thermal fluids that have risen mainly from great irregular bodies of intruding magmas which are called batholiths. Probably 95 per cent of such lode systems have formed in connection with acidic or "granitic" batholiths and probably less than 5 per cent have formed in connection with basic intrusives. The study of lode ores, therefore, should include the study of the intrusion and differentiation of the batholith. It was noted long ago1 that certain tin-bearing deposits are commonly associated with small stocks. That small stocks are cupolas of larger intrusive masses has generally been recognized. Butler,2 in his studies of the ore deposits of Utah, showed that the chief deposits in Utah are in and near the stocks; that is near the "apically truncated

Jan 1, 1933

By H. Conrad, E. Stofel

The fracture behavior of 60-deg-oriented sapphire crystals was investigated for both tension and compression. Plastic flow on the basal plane was found to be a factor in reducing the tensile stress required to produce fracture in the temperature RECENT experiments1-' have shown that single crystals of a alumina (sapphire) can deform plastically, particularly at temperatures greater than 1000°C. The effect of this plastic flow on the fracture behavior of sapphire was not established, but range 1100º to 1500ºC. Mechanical twins, both (0001) and (0111) types, were produced by compression in the temperature range 1100" to 1300°C. Cracks propagated more readily along the twin boundaries than in the nontwinned crystal. experiments with other ceramic crystals4'5 have shown that plastic flow can initiate cracks that lead to catastrophic failure. This suggests by analogy that plastic flow might also be an important factor in the fracture of sapphire crystals. A recent experimental investigationS undertaken to determine the mechanism of plastic flow in sapphire provided an opportunity to study the type of fracture produced after various amounts of plastic shear strain. The results of this study of fracture are reported in the present paper. During the course of

Jan 1, 1963

By C. M. Marquardt

The minerals industry in general should bow in homage to the uranium milling industry. Those in the uranium milling industry have "spark- plugged" more progress in the application of instrumentation and control in the last 5 years than has been made in 50 years by the industry in general. Part of this real progress in the application of instrumentation and control has been born of necessity because milling processes are more complex. A lot of the impetus for instrumentation and control has come from the fact that the industry is new, the processes are new, and there are no hide-bound conventions to overcome. Part of it comes from the fact that much of processing is more chemical than metallurgical and the thinking of the process chemist has carried over into the plants. One need not elaborate on what instrumentation has done for the process chemical industries. Each new mill that is constructed, if of appreciable size, seems to employ more instrumentation than the previously completed plant. Plant A makes a break-through in the application of instrumentation to a particular part of the process and Plant B accepts this and goes one step farther, while Plant C, anticipating Plant B, makes two or three more steps before Plant B is entirely leveled out.

Jan 9, 1958

By Hassell E. Hunter

The Wyoming Minerals - Conoco Crownpoint Joint Venture represents the first time that big hole drilling has been exclusively used to develop a privately financed mine. Three shafts, one ten feet in diameter and two six feet in diameter, have been successfully drilled to depths of 2243', 2188' and 2188' respectively and lined with hydrostatic designed steel casing. The largest shaft is to be used to as a development shaft to handle muck and water from enlargement and station excavation of the other two shafts. A reverse fluid air assist circulation system with potassium base mud was used during drilling. The mud was cleaned by settling in steel lined tanks with assistance from cyclone type sand separators. Deviation was monitored with wireline gyroscopic surveying instruments at 30 foot intervals. Horizontal departure did not exceed 16 inches off perpendicular. Casing was designed to withstand full hydrostatic pressures with a 1.5 safety factor for the large shaft and 1.25 safety factor for the two smaller shafts. All casing welds were x-rayed prior to lowering the casing into the hole. Cementing the annular space completed the operation. The total time to mobilize, drill and move off the three shafts was 363 days. The drilling operation was completed ahead of schedule and under budget.

Jan 1, 1982

By Brandon H. Grove

In Austria's only producing field, at Zistersdorf, Erdoel Produktions-gesellschaft completed a single new producer, its well Gosting 6 coming in early in October for an average production of about 15 tons daily. For further testing within the proved part of the field this company's Gosting 7 was at the close of the year drilling in Pannonian strata at 760 m., and its Gosting 8 was rigging up. Outside of the proved area of the Zistersdorf field two further tests located on the Steinberg dome failed to find production in the known oil-bearing strata of the Sarmatian, and were deepened as wildcats into the Cretaceous Flysch. The first of these, Neusiedel 1, about one kilometer north of the known producing area, found oil in the Flysch beds at a depth of 1290 m. for an initial production of about 10 tons per day. The second test, Windisch Baumgarten la, is an old well previously considered a failure, which when deepened achieved a production of about 5 tons per day in the Flysch Inoceramus beds at 985 m. Neither of the foregoing wells is producing from a stratigraphically definable horizon, oil accumulation in the Flysch of this area being apparently controlled by tectonic breccias or related crevices.

Jan 1, 1937

By J. C. Coughlin, M. C. Flemings, T. Z. Kattamis

Experiments on Al-4.5 pct Cu alloy shou the dendrite arnz spacing increases with time during isothermal holding in the liquid-solid region. This coarsening of the dendrite structure is then shown to occur at roughly the same rate during solidification as during isothermal holding. Final dendrite arm spacing in both types of experiments depends primarily on coarsening kinetics. It is concluded that driving force for the coarsening is reduction of liquid-solid sur/ace area. Calculations based on two simple models show qualitative apreement with experinzent. 1 HERE has been considerable interest in recent years in determining effects of solidification variables on dendrite arm spacing in cast alloys. The interest has resulted primarily from the clear evidence that 1) the degree of homogeneity which can be obtained in a cast alloy with commercially practical homogeni- zation treatments depends on dendrite arm spacing, and 2) mechanical properties of the heat-treated casting depend on the homogeneity obtained.'-' In wrought alloys, microsegregation from the original ingot is carried to some extent into the final wrought product, and affects mechanical properties in similar fashion Experimental evidence available indicates that dendrite arm spacing in cast aluminum alloys is influenced only by cooling rate (or "local solidification timev*) and alloy content.Fig. 1, for example,

Jan 1, 1968

By C. Elbaum

If a thin layer of liquid gallium is spread on a surface of solid aluminum, the gallium penetrates high-angle grain boundaries at a very rapid rate and separation along these boundaries follows. An experiment was carried out to investigate this phenomenon. A well-annealed specimen of aluminum 99.994 pct pure, consisting of several large grains was used, Fig. 1. The dimensions of the sample were 25 mm wide by 2.5 mm thick and all the grain boundaries extended through the entire thickness of the plate. This sample was prepared by strain-annealing and, as can be seen in Fig. 1, contained one long, straight boundary. An examination of the crystal orientations showed this boundary to be a coherent twin boundary. The angular misorientations between the grains forming the other boundaries were all in excess of 20 deg. A thin layer of liquid gallium was spread on one side of the specimen at about 30°C (the melting point of gallium is 29.7"C). After the application of the liquid the temperature was lowered to about 27°C. The gallium remained liquid at this temperature and it can be seen from the A1-Ga phase diagram1 that the liquid was probably saturated with aluminum.

Jan 1, 1960

GENTLEMEN : Herewith are transmitted the reports of your Treasurer and the Chairmen of your standing committees on Admissions, Membership, Papers and Publications, and Library for the calendar year 1931. To these reports you are referred for further details of the year's activities. Finances.-Depressed industrial conditions prevailing throughout the year were reflected in a substantial decline in current revenue. Aside from interest on sundry special funds (but including that from the Life Membership, Library, and General Reserve Funds) total receipts amounted to $168,274, compared with $194,636 in 1930. The principal items of decrease were $17,000 in advertising income from the monthly magazine MINING AND METALLURGY, and about $9,600 in dues and initiation fees. Of this shrinkage $4,000 is accounted for by decrease in the number of new members enrolled; and $5,600 by diminished income from current dues and arrearages. This naturally has coincided with an \ increase in delinquency and "drops" or suspensions for nonpayment of dues. The decline in advertising income, amounting to 38 per cent as compared with that of 1930, in general paralleled the experience of all technical and trade publications; and it is problematical whether 1932 will show as large a return from advertising as did 1931.

Jan 1, 1932

By John H. Schissler

INTRODUCTION AND SUMMARY Complex copper-lead-zinc ore is mined from underground workings high in the Western Cordillera of the Andes mountains about 100 km in a stralght line north of the city of Arequipa in southern Peru. The Madrigal mine is situated in a steep-walled canyon into which the six operating levels "daylight". Production is from cut-and-fill stopes currently producing approximately 740 dry metric tons per day. The Santa Rosa vein, the most important producer in the district, outcrops for a distance of about 4 km, bearing N 75º W and dipping about 70º NE. In places the vein splits into two or three branches; widths of each vary between 1 and 4 m and total mineralized widths of up to over 8 m occur. Principal ore minerals are chalcopyrite, galena and sphalerite. Ore reserve grades for the Madrigal mine average about 1.45% Cu, 2.6% Pb and 5.0% Zn, 2.9 ozAg per metric ton. [Compania] Minera del Madrigal is a California limited partnership; the general partner and operator is [Compania] Madrigal, a wholly-owned subsidiary of Homestake Mining Company. HISTORY Shallow workings found on the Santa Rosa vein were probably made by the Spaniards during colonial times in their search for

Jan 1, 1977

By M. L. Holzworth, Joseph C. Kremer, Paul A. Beck, L. J. Demer

FOR alloys which are in practice heat treated to obtain increased strength, such as steels, duralumin, copper-beryllium, and others, the treatment usually involves heating to a relatively high temperature. At such temperatures the grain size of the product is largely determined by grain growth. Even in metals and alloys annealed merely to relieve work hardening, recrystallization is generally followed by a certain amount of grain growth. Thus, effective grain size control, which is often of great practical importance in manufacturing processes, depends on the grain growth behavior of the material used. Despite its importance, grain growth has been the subject of few investigations of a fundamental nature. The term "grain growth" has been used to designate a group of related, but distinctly different, phenomena. The two most important and best known of this group are illustrated by the following example. Curve a in Fig r shows the increase of the average grain size of a copper-beryllium alloy, containing 2 pct Be and 0.15 pct Co, with increasing annealing temperature. The time of annealing was 2 hrs. The grain size was quite uniform in all specimens. The results of a similar experiment with an alloy containing 2 pct Be and 0.31 pct Co are shown by curve b. It is seen that for any annealing temperature below T. the grain size was smaller than in the previous case. Grain growth became slower with the higher Co content. This "inhibiting" effect of the higher Co addition was associated with the appearance in the microstructure of fine, light blue particles of the CoBe phase. Up to temperature T. the structure of the inhibited alloy (curve b) was just as uniform as the structures represented by curve a. However, after annealing at T, or at higher temperatures, the inhibited alloy showed some extremely large grains (much larger than the grain sizes developed by the uninhibited alloy with low Co content) mixed with the small grains according to curve b. The presence of these mixed or "duplex" structures is indicated in Fig 11 by the vertical lines branching off curve b. The type of grain growth occurring in uninhibited Cu-Be alloys (curve a) has has been most frequently and best investigated in brass. This type has been designated as "normal grain growth," while the grain growth phenomena occurring in inhibited materials were, at times, referred to as "abnormal grain growth." However, since the latter term has been applied occasionally to the phenomenon of critical recrystallization, which also results in large grains although by an entirely different mechanism, in the present paper a different nomenclature has been adopted in order to avoid confusion. Typical of the grain growth in uninhibited metals and alloys is the continuous

Jan 1, 1947

By R. P. Carreker

THE experiments described in this report were conducted as a part of a general program designed to document the deformation behavior of pure metals over a wide range of temperature. Material The silver used in this investigation was obtained from the Handy and Harmon Co. as 99.97+ pct pure. It is from the same length of wire as that designated H-H silver by Hoffman and Turnbull in their investigation of self-diffusion in silver.' The silver was drawn at room temperature from 0.060-in. diam to 0.020-in. diam wire without intermediate annealing. Seven-inch lengths of cold-drawn wire were annealed in groups of ten by placing them in individual quartz tubes spaced circumferentially about and near the vertical furnace axis. Dry nitrogen was passed through the furnace to lower the partial pressure of oxygen. The three annealing temperatures used were 700°, 800°, and 900°C, producing grain sizes of 0.017, 0.040, and 0.250 mm diam after 30 min at temperature. Testing Procedure The details of the testing procedure have been described in the reporting of results of a similar investigation of Copper. Annealed specimens of 5-in. gage length were gripped between grooved plates. Tests were performed using an Instron tensile-test-

Jan 1, 1958

By J. R. Dawson, J. A. Glunt

Vesta No. 4 and 5 mines supply most of the high volatile coal required for Jones & Laughlin's by-product coke plants. Until 1944 all coal produced in these mines was loaded by hand. Pressure to mechanize at Vesta was brought on by the manpower shortage in World War II, and in 1943 a decision was made to change to mechanical loading. It was the opinion of those concerned that by use of selective mining the coal would be clean enough to be processed by the existing preparation plants. At that time coal cleaning at Jones & Laughlin consisted of hand picking the larger sizes at the mine tipples and wet washing at plants located at the Pittsburgh and Aliquippa Works. A typical section of the Pittsburgh seam as it occurs at Vesta is shown in Fig. 1. The 14 to 16 in. of drawslate immediately over the coal is too soft to be used for roof and must be taken down, leaving the rooster coal just above for roof. In selective mining an attempt is made to mine the coal under the drawslate first and then load out the drawslate separately as refuse. In full seam mining slate and coal are shot down at the same time and loaded out.

Dec 1, 1956

By Alvin H. Lense

In the spring of 1967, after a careful study of existing geology along the Pacific Coast including Alaska, the USBM, in conjunction with the USGS, decided that the offshore area around Nome, Alaska, presented an unparalleled land-to-sea comparison site for the evaluation of marine core drilling techniques and sampling equipment. Considering the geological evidence available and the production history of the Nome Beaches (5-6 million oz. of gold recovered), it appeared likely that gold in commercial quantities could occur in the offshore area. A 180 sq mi area of Norton Sound, extending roughly 14 miles to the east and west of Nome and averaging 6 miles to the south, was tested by approximately 530 line-miles of sub-bottom profiling. A total of 4043 ft (56 holes) were drilled in unconsolidated sediments, yielding mixtures of gravel, sand, silt and clay. Of the total holes drilled, 16 went to bedrock and six were terminated short of their intended depths due to boulders which halted penetration, or rough seas which caused the ship to move as the anchors slipped over hard sea-floor surface. The rest of the holes were terminated when the penetrative capabilities of the drills were reached, or when the required amount of geological data were attained.

Jan 8, 1968

By G. F. Olsen

ON superficial consideration a technical library might be considered a luxury to the business institution that possesses one. After all, public libraries and research institutions probably contain all the data that would be found in a private technical library, and able consultants are available both within and without a company. In all probability the technical men of a company have in their combined personal libraries sufficient information to answer most inquiries. Nevertheless, possession of such a department is of real economic benefit because of the time it saves its users, because it prevents expensive duplication of technical literature in a company, and lastly, but most important, be- cause it makes readily available a central storehouse of technical facts classified and indexed to meet the demands of the industry or industries concerned.

Jan 1, 1940