Search Documents

By F. L. Vogel

Densities and distributions of dislocations in plastically bent germanium crystals before and after annealing were studied. In the bent and annealed crystals, the theoretical relationship between radius of curvature and density of dislocations is confirmed. Before annealing, however, more dislocations are present than required, and these are distributed with a minimum at the neutral axis and maxima at the top and bottom surfaces. On annealing, three significant changes occur in the bent bars: 1) the average dislocation density is reduced, presumably by the annihilation of opposite signs; 2) dislocations migrate from the high density outside regions toward the low density neutral axis, thus producing the equilibrium distribution of dislocations; and 3) a polygonized structure is formed by movement of the dislocations into walls normal to the slip plane. ETCHING to reveal edge dislocations'-" offers a unique opportunity to study, in germanium single crystals, the functioning of dislocations in plastic deformation. Plastic bending is ideally suited to this purpose because it produces a static array of edge dislocations in an ideally plastic material which is predictable from the theory." " Nye" has given a rather complete treatment of the geometry of bent crystals in terms of dislocations. The density of excess dislocations is related to the radius of curvature of the slip plane of a bent crystal, as shown in Fig. 1, assuming the absence of macroscopic elastic stresses. The curvature of any plane in the zone of the bend axis is found by resolving the Burgers vector into that plane, so that for the usual case where the slip plane is inclined at some angle 0 to the neutral plane of the bar, the equation applies, with T equal to the radius of curvature of the neutral plane of the bent crystal. Two predictions which are relevant to this study may be made from Eq. 1. First, in crystals bent to various radii, the average excess dislocation density is inversely proportional to the radius and second, for a bar bent to a radius which is large compared with its thick-

Jan 1, 1957

By Frank Haas

THE public generally has-become aware that there is something wrong with the coal industry and a clamor has arisen for an explanation if not a remedy for this disorder. It is only reasonable that this Institute be looked to for a diagnosis to show the way for some other .agency to prepare the patient for prescription or operation. The subject is extensive, widely diversified, and beyond the efforts of an individual to cover completely; one of the objects of this paper is the initiating of a symposium on the non- technical factors essential to an understanding of the bituminous coal industry. The present condition of the coal industry cannot be described in a few words but, in effect, it resolves itself into a simple statement: The average coal operator is losing money notwithstanding a firm conviction on the part of the consumer that he pays too much for his coal. Without enumerating the many and varied. factors which contribute to this condition, this paper will be devoted to the interrelation of taxation and ownership of coal and its effect on finance

Jan 1, 1930

By J. L. Wyatt

THE smelting of ilmenite to produce a slag rich in titanium, with pig-iron as a byproduct, introduces new concepts in electric smelting metallurgy. Titanium slags are characterized by low electrical resistance, thereby requiring a different type of electric furnace operation, and power supply sources substantially different from those encountered in normal steel melting and siliceous ore smelting furnaces. This paper describes special apparatus for determining specific electrical resistivity of titanium slags, and reports the values obtained on slags encountered in the process of smelting ilmenite ores. In an induction furnace under conditions approximating normal furnacing operation, 25 general heats and 6 special standardization and comparison heats were run. Results indicate relatively low resistivity. Resistivity depends primarily on slag composition, and, to a lesser degree, on temperature. During the summer of 1947 a cooperative project between the National Lead Co. and the Bureau of Mines was conducted at Boulder City, Nevada, in the Electrometallurgical Laboratories of the Bureau. The project involved smelting of ilmenite ores in electric furnaces, and has been reported in detail.' The author participated as a member of the staff of the National Lead Co. during the entire campaign. One outstanding characteristic of the titaniferous slags, their apparently excellent and variable electrical conductivity, was considered sufficiently important to warrant further study. Although little electric smelting of iron ores has been done in the United States, a certain amount of information is available for comparative purposes. Personal experience in smelting siliceous iron ores in electric furnaces furnished further information for comparison. In general, silicate slags are relatively poor conductors of electricity. Current flow during smelting operations may be maintained through a floating layer of coke on top of the slag bath, or through a bath of molten iron, beneath the slag. Silicate slags are not sufficiently conductive to furnish a path for current passage when normal furnace voltages are used. Experimental smelting of a silicate iron ore was undertaken for comparative purposes. A fluid melt was not obtained until the FeO content was reduced to 15 pct. The resistivity increased as the FeO content decreased, FeO compounds being the most conductive of the various oxides in such a normal slag system. The converse appears to be true in slags containing large percentages of TiO2. It has been found that titanium slags become molten with FeO percentages in excess of 30 pct, and that the conductivity becomes generally better as the FeO con-tent of the slag diminishes. This phenomenon was demonstrated in the furnacing operations at Boulder City. During the initial smelting period furnace electrodes could be held immersed several inches in the slag, with tap selectors set for a no-load voltage of 70 v. As the FeO content decreased, the furnace electrodes would "walk up," until at one point in the process the tips would break the surface and arc on top of the slag. This was undesirable since direct arcing caused losses of important flux additions. The slag compositions under study at that time were such that losses due to surface arcing sometimes caused viscous slags to be formed. Forcing the electrodes into the slag bath by manual control to prevent surface arcing resulted in excessive power input and lack of control. Suitable low voltages were not available. Measurement of the electrical resistivity of titanium slags at various operating temperatures and slag compositions was undertaken. It was believed that this information would be of use in the design of electric furnaces suitable for smelting ilmenite, with voltages, electrode sizes, and electrode spacing adapted specifically to titanium slags.

Jan 1, 1951

By C. S. Barrett

The torsional after-effect in polycrystalline cadmium is interrupted by an abnormal twisting when the film is removed by etching. This is accounted for by the pile-up of dislocations beneath anodic or other oxide films during the original twisting, and the relief of the residual stresses from these by elastic and plastic processes during etching. WHEN an iron or zinc wire coated with oxide is plastically twisted and then released, it untwists according to a law of equal increments in equal intervals of log time, but if the oxide is suddenly removed by etching this normal after-effect is interrupted by a transient, and thereafter the untwisting is slower.' Etching may even reverse the strain temporarily. Related effects caused by hydrated oxide films on cadmium in creep tests have been observed by Phillips and Thompson:' definite transient strains caused by the removal of the film from single crystals of cadmium were observed; however, negligible effects were obtained with polycrystalline wires. Pronounced effects of both transient and steady nature were observed by Phillips and Thompson when anodic films 10-4 cm thick were etched off, and weak effects, transient only, occurred with hydrated oxide films 3x10 cm thick such as were formed by standing in water for 10 min. It was estimated that 10.' cm films, formed in water in 1 or 2 min, could be detected in the apparatus of Phillips and Thompson. Since abnormal after-effects were observed by the torsion method equally well with polycrystalline and monocrystalline iron and zinc wires,' it was anticipated that the torsion method would also disclose them in polycrystalline cadmium, in spite of the fact that analogous effects had not been observed in tensile creep tests on polycrystalline zinc by Pickus and Parker3 r on polycrystalline cadmium in tensile studies by Andrade and Randall." Because of its high sensitivity, particularly its sensitivity to surface conditions, the torsion method was thought to merit further study as a method of investigating thin films of various types and the action of various reagents on these films. Materials and Methods Cadmium wires were cold-drawn to a diameter of 0.039 in. from a stock that was determined spectro-scopically to contain 0.05 pct Bi, 0.005 pct Cu, 0.008 pct Pb, and 0.007 pct Si. The wires were cut to about 17/8 in. lengths and were annealed 1 hr in air at 290°C, after which the grain size was such that there were 5 to 7 grains across a diameter. The wires were then mounted as indicated in the insert in Fig. 1, one end being fastened with laboratory wax into a small diameter brass tube and the other end being waxed to a thin glass fiber which supported, on its upper end, a small galvanometer mirror. The wires were waxed with care to avoid straining or annealing, for it was found that the after-effect rate was sensitive to prior cold work in a wire. The assembly was then clamped above a beaker into which the reagent could be poured. The lower end of the wire was held in the hand while the wire was twisted 180"; it was then released immediately. Since precision timing of these manipulations was not attempted, the different wires cannot be compared as to exact rates of untwisting. The length subjected to plastic strain was 15/8 in. The surface coatings studied were those produced by the annealing in air, by anodic treatment of

Jan 1, 1954

By A. J. Weinig

NEED for some simple method of determining tonnages in mill circuits has always been felt by operators and consultants alike. To meet this demand the following method was evolved and has been found accurate and practical after considerable testing on various mill flows. The essence of the method is to add a chemical at a uniform rate to a mill flow, such as a launder conveying pulp, and then determine the concentration of the added chemical in a sample of the pulp. From this procedure the tonnage can be calculated. Common table salt has proved the most satisfactory chemical for ordinary conditions. It has many decided advantages for use in tonnage determinations, among them being the following:

Jan 1, 1933

By W. F. Holbrook, C. E. Wood, E. P. Barrett

The Blast Furnace Studies Section, Metallurgieal Division, Bureau of Mines, has been working for several years on the mechanism of desulphurization of iron and steel by slags. The usual assumption that desulphurization takes place by diffusion of FeS from metal into slag and subsequent reaction of this FeS with CaO to produce CaS has seemed to us inconsistent with a number of experimental results we have obtained. We undertook, for example, to determine the proportion of sulphur in a slag present as FeS. An entirely satisfactory method of doing this has not yet been evolved. The results of extraction with metallic antimony led to an interesting conclusion, however. FeS is readily soluble in metallic antimony, either physically or by chemical reaction. On the other hand, CaS was found to be insoluble. Hence it would appear that by rapid extraction of the slag with antimony we might expect to determine the distribution of sulphur between iron and calcium. The results showed that much of the sulphur was present as FeS. In some instances the extraction of sulphur as FeS was almost quantitative. For example, in a slag containing 3.8 grams Fe and 3.7 grams S, extraction removed 1.18 grams S and 2.12 grams Fe. If all the iron present in the antimony had been FeS, 1.21 grams S would have been extracted. In another slag with 8.6 grams Fe and 0.06 gram S present, 0.14 gram Fe and 0.08 gram S were extracted. This was obviously extraction of sulphur as FeS within the analytical error and showed that FeS was present either in solution or as a dispersion. Attempts to determine the solubility of FeS and CaS in slag by quenching and ultramicroscopic investigation have indicated that the solubility of FeS is very low, and that reactions in the slag are probably not to be considered as homogeneous. A more detailed report on these theoretical considerations will be made at a later date.

Jan 1, 1940

By W. F. Holbrook, C. E. Wood, E. P. Barrett

The Blast Furnace Studies Section, Metallurgieal Division, Bureau of Mines, has been working for several years on the mechanism of desulphurization of iron and steel by slags. The usual assumption that desulphurization takes place by diffusion of FeS from metal into slag and subsequent reaction of this FeS with CaO to produce CaS has seemed to us inconsistent with a number of experimental results we have obtained. We undertook, for example, to determine the proportion of sulphur in a slag present as FeS. An entirely satisfactory method of doing this has not yet been evolved. The results of extraction with metallic antimony led to an interesting conclusion, however. FeS is readily soluble in metallic antimony, either physically or by chemical reaction. On the other hand, CaS was found to be insoluble. Hence it would appear that by rapid extraction of the slag with antimony we might expect to determine the distribution of sulphur between iron and calcium. The results showed that much of the sulphur was present as FeS. In some instances the extraction of sulphur as FeS was almost quantitative. For example, in a slag containing 3.8 grams Fe and 3.7 grams S, extraction removed 1.18 grams S and 2.12 grams Fe. If all the iron present in the antimony had been FeS, 1.21 grams S would have been extracted. In another slag with 8.6 grams Fe and 0.06 gram S present, 0.14 gram Fe and 0.08 gram S were extracted. This was obviously extraction of sulphur as FeS within the analytical error and showed that FeS was present either in solution or as a dispersion. Attempts to determine the solubility of FeS and CaS in slag by quenching and ultramicroscopic investigation have indicated that the solubility of FeS is very low, and that reactions in the slag are probably not to be considered as homogeneous. A more detailed report on these theoretical considerations will be made at a later date.

Jan 1, 1940

By R. B. Porter, R. P. Porter, R. A. Lothrop

Changes became necessary in dredging methods employed in Idaho through passage of the Dredge Mining Protective Act (1954). Among other provisions, the law requires dredge operators to construct settling ponds of sufficient capacity and character to reasonably clarify the water used in the mining process before such water is discharged into the stream. Porter Bros. Corp., a placer mining company with many years operating experience in Oregon and Montana, became interested in strategic mineral placers in Idaho in 1950 when it was learned that prospectors had discovered a radioactive mineral deposit in Bear Valley Creek, 95 miles northeast of Boise. The company acquired mining leases and proceeded with exploration and development work on the property. After extensive research had resulted in the determination of successful separation processes, contracts were negotiated with the federal government and deliveries of columbium-tantalum and uranium concentrates commenced in 1956. The mining operations are located in a primitive area of Idaho among salmon spawning grounds and crystal-clear mountain trout streams. To avoid involvement in a very controversial issue, it appeared advisable for the company to develop water treatment procedures exceeding those requirements stated in the Idaho Dredge Mining Protective Act. Operation: The company operates one 6 cu ft continuous bucketline dredge and one 4 1/4 cu ft continuous bucketline dredge on the property. The dredges are jig-equipped, with feed being screened to 3 in. by trommels. The screening and gravity concentration methods satisfactorily separate the heavy minerals from companion clays, sand, and gravel. However, this separation of the heavy minerals requires water from the dredge pond with a minimum content of silt and colloids; therefore, water for dilution is added continuously to the dredge pond to suppress solids buildup. Discharge of this highly turbid water to maintain the proper pond level would ultimately result in an excessive silt load in Bear Valley Creek. To prohibit the turbid pond water from flowing directly into Bear Valley Creek, it was necessary to isolate the dredging area. Main by-pass canals were constructed along each side of the dredge pond and numerous secondary canals were dug for diverting seepage and snow runoff. One by-pass canal, extending more than two miles along the west side of the valley, diverts the main stream as well as tributaries entering from the west; a canal east of the dredge area diverts streams entering from that direction. At the beginning of operations in 1956, the dredge pond effluent was filtered through tailings and settled by use of coagulents in a series of lagoons. The filtrate was then discharged directly into the stream. Although this procedure gave satisfactory results in conformance with the state law, ice buildup and lagoon freezing hindered the efficiency of the process during periods of low temperature. For this reason, testing began in 1956 on a water treatment process that would operate efficiently under the extreme weather conditions encountered in Bear Valley. Development of Water Treatment System: Porter Bros. Corp. established the following requirements for effective continuous treatment of dredge pond effluent to the stream which, at low flow conditions, effluent to the stream which, at low flow conditions, would not result in a turbidity exceeding 25 ppm in the stream, 2) produce a sludge sufficiently dense to minimize disposal area requirements, 3) be semi-portable to follow dredge movements, 4) be capable of operating at low temperatures, and 5) be capable of handling a variety of capacities and turbidities.

Jan 1, 1961

By C. E. Wood

THE Blast Furnace Studies Section, Metallurgical Division, Bureau of Mines, has been working for several years on the mechanism of desulphurization of iron and steel by slags. The usual assumption that desulphurization takes place by diffusion of FeS from metal into slag and subsequent reaction of this FeS with CaO to produce CaS has seemed to us inconsistent with a number of experimental results we have obtained. We undertook, for example, to determine the proportion of sulphur in a slag present as FeS. An entirely satisfactory method of doing this has not yet been evolved. The results of extraction with metallic antimony led to an interesting conclusion, however. FeS is readily soluble in metallic antimony, either physically or by chemical reaction. On the other hand, CaS was found to be insoluble. Hence it would appear that by rapid extraction of the slag with antimony we might expect to determine the distribution of sulphur between iron and calcium. The results showed that much of the sulphur was present as FeS. In some instances the extraction of sulphur as FeS was almost quantitative. For example, in a slag containing 3.8 grams Fe and 3.7 grams S, extraction removed 1.18 grams S and 2.12 grams Fe. If all the iron present in the antimony had been FeS, 1.21 grams S would have been extracted. In another slag with 8.6 grams Fe and 0.06 gram S present, 0.14 gram Fe and 0.08 gram S were extracted. This was obviously extraction of sulphur as FeS within the analytical error and showed that FeS was present either in solution or as a dispersion. Attempts to determine the solubility of FeS and CaS in slag by quenching and ultramicroscopic investigation have indicated that the solubility of FeS is very low, and that reactions in the slag are probably not to be considered as homogeneous. A more detailed report on these theoretical considerations will be made at a later date.

Jan 1, 1939

By Glenn S. Wyman

CHUQUICAMATA, located in northern Chile in the Province of Antofagasta, is on the western slope of the Andes at an elevation of 9500 ft. Because of its position on the eastern edge of the Atacama Desert, the climate is extremely arid with practically no precipitation, either rain or snow. All primary blasting in the open-pit mine at Chuquicamata is done by the churn drill, blasthole method. Since 1915, when the first tonnages of importance were removed from the open pit, there have been many changes in the blasting practice, but no clear-cut rules of method and procedure have been devised for application to the mine as a whole. One general fact stands out: both the ore and waste rock at Chuquicamata are difficult to break satisfactorily for the most efficient operation of power shovels. Numerous experiments have been made in an effort to improve the breakage and thereby increase the shovel efficiency. Holes of different diameter have been drilled, the length of toe and spacing of holes have been varied, and several types of explosives have been used. Early blasting was done by the tunnel method. The banks were high, generally 30 m, requiring the use of large charges of black powder, detonated by electric blasting caps. Large tonnages were broken at comparatively low cost, but the method left such a large proportion of oversize material for secondary blasting that satisfactory shovel operation was practically impossible. Railroad-type steam and electric shovels then in service proved unequal to the task of efficiently handling the large proportion of oversize material produced. The clean-up of high banks proved to be dangerous and expensive as large quantities of explosive were consumed in dressing these banks, and from time to time the shovels were damaged by rock slides. As early as 1923 the high benches were divided, and a standard height of 12 m was selected for the development of new benches. The recently acquired Bucyrus-Erie 550-B shovel, with its greater radius of operation compared to the Bucyrus-Erie 320-B formerly used for bench development, allowed the bench height to be increased to 16 m. Churn drill, blasthole shooting proved to be successful, and tunnel blasts were limited to certain locations where development existed or natural ground conditions made the method more attractive than the use of churn drill holes. Liquid oxygen explosive and black powder were used along with dynamite of various grades in blast-hole loading up to early 1937. Liquid oxygen and black powder were discontinued because they were more difficult to handle due to their sensitivity to fire or sparks in the extremely dry climate. At present ammonium nitrate dynamite is favored because of its superior handling qualities and its adaptability to the dry condition found in 90 pct of the mine. In wet holes, which are found only in the lowest bench of the pit and account for the remaining 10 pct of the ground to be broken, Nitramon in 8x24-in. cans, or ammonium nitrate dynamite packed in 8x24-in. paper cartridges, is being used. This latter explosive, which is protected by a special antiwetting agent that makes the cartridges resistant to water for about 24 hr, currently is considered the best available for the work and is preferred over Nitramon. Early churn drill hole shots detonated by electric blasting caps, one in each hole, gave trouble because of misfires caused by the improper balance of resistance in the electrical circuits. Primarily, it was of vital importance to effect an absolute balance of resistance in these circuits, the undertaking and completion of which invariably caused delays in the shooting schedule. Misfires resulting from the improper balance of electrical circuits, or from any other cause, were extremely hazardous, since holes had to be unloaded or fired by the insertion of another detonator. The advent of cordeau, later followed by primacord, corrected this particular difficulty and therefore reduced the possibility of missed holes. After much experimentation, the blasting practice evolved into single row, multihole shots, with the holes spaced 4.5 to 5 m center to center in a row 7.5 to 8 m back from the toe. Sucti shots were fired from either end by electric blasting caps attached to the main trunk lines of cordeau or primacord. The detonating speed of cordeau or primacord gave the practical effect of firing all holes instantaneously. Double row and multirow blasts, fired instantaneously with cordeau or primacord, proved to be unsatisfactory in the type of rock found at Chuquica-

Jan 1, 1953

By Glenn S. Wyman

CHUQUICAMATA, located in northern Chile in the Province of Antofagasta, is on the western slope of the Andes at an elevation of 9500 ft. Because of its position on the eastern edge of the Atacama Desert, the climate is extremely arid with practically no precipitation, either rain or snow. All primary blasting in the open-pit mine at Chuquicamata is done by the churn drill, blasthole method. Since 1915, when the first tonnages of importance were removed from the open pit, there have been many changes in the blasting practice, but no clear-cut rules of method and procedure have been devised for application to the mine as a whole. One general fact stands out: both the ore and waste rock at Chuquicamata are difficult to break satisfactorily for the most efficient operation of power shovels. Numerous experiments have been made in an effort to improve the breakage and thereby increase the shovel efficiency. Holes of different diameter have been drilled, the length of toe and spacing of holes have been varied, and several types of explosives have been used. Early blasting was done by the tunnel method. The banks were high, generally 30 m, requiring the use of large charges of black powder, detonated by electric blasting caps. Large tonnages were broken at comparatively low cost, but the method left such a large proportion of oversize material for secondary blasting that satisfactory shovel operation was practically impossible. Railroad-type steam and electric shovels then in service proved unequal to the task of efficiently handling the large proportion of oversize material produced. The clean-up of high banks proved to be dangerous and expensive as large quantities of explosive were consumed in dressing these banks, and from time to time the shovels were damaged by rock slides. As early as 1923 the high benches were divided, and a standard height of 12 m was selected for the development of new benches. The recently acquired Bucyrus-Erie 550-B shovel, with its greater radius of operation compared to the Bucyrus-Erie 320-B formerly used for bench development, allowed the bench height to be increased to 16 m. Churn drill, blasthole shooting proved to be successful, and tunnel blasts were limited to certain locations where development existed or natural ground conditions made the method more attractive than the use of churn drill holes. Liquid oxygen explosive and black powder were used along with dynamite of various grades in blast-hole loading up to early 1937. Liquid oxygen and black powder were discontinued because they were more difficult to handle due to their sensitivity to fire or sparks in the extremely dry climate. At present ammonium nitrate dynamite is favored because of its superior handling qualities and its adaptability to the dry condition found in 90 pct of the mine. In wet holes, which are found only in the lowest bench of the pit and account for the remaining 10 pct of the ground to be broken, Nitramon in 8x24-in. cans, or ammonium nitrate dynamite packed in 8x24-in. paper cartridges, is being used. This latter explosive, which is protected by a special antiwetting agent that makes the cartridges resistant to water for about 24 hr, currently is considered the best available for the work and is preferred over Nitramon. Early churn drill hole shots detonated by electric blasting caps, one in each hole, gave trouble because of misfires caused by the improper balance of resistance in the electrical circuits. Primarily, it was of vital importance to effect an absolute balance of resistance in these circuits, the undertaking and completion of which invariably caused delays in the shooting schedule. Misfires resulting from the improper balance of electrical circuits, or from any other cause, were extremely hazardous, since holes had to be unloaded or fired by the insertion of another detonator. The advent of cordeau, later followed by primacord, corrected this particular difficulty and therefore reduced the possibility of missed holes. After much experimentation, the blasting practice evolved into single row, multihole shots, with the holes spaced 4.5 to 5 m center to center in a row 7.5 to 8 m back from the toe. Sucti shots were fired from either end by electric blasting caps attached to the main trunk lines of cordeau or primacord. The detonating speed of cordeau or primacord gave the practical effect of firing all holes instantaneously. Double row and multirow blasts, fired instantaneously with cordeau or primacord, proved to be unsatisfactory in the type of rock found at Chuquica-

Jan 1, 1953

By Bert S. Sandell

Much has been said and written about the various uses of die castings, their applications in the various industries and their advantages and disadvantages. Examination of this literature, however, fails to disclose any data concerning the effect of temperature upon any of the physical properties of die-casting alloys. The uses and applications of die castings are so numerous, and of such a varied nature, that far too lengthy a manuscript would be required to list all of them. Brief mention of some specific cases will suffice to illustrate the temperature ranges in which certain die castings function. Automobile hardware, such as hub caps, door handles, radiator caps, etc., can be used as one example. Castings of this type are constantly exposed to varying climatic conditions, temperatures ranging from below zero to upwards of 100" F. Refrigerator parts, such as ice-cube trays, etc., form another example. Approaching the other temperature extreme, we encounter conditions such as are found in kitchens in which oven-heat indicator parts, cooking utensils, waffle grids, etc., embody use of die castings, where temperatures as high as 500" F. are often met with. Because of this variation in service temperatures, it was felt necessary to ascertain the effect of these temperatures upon the physical properties of die-casting alloys. The Charpy impact test was chosen first because of its simplicity, and because of the fact that brittleness is more likely to be objectionable in die castings than hardness or other physical properties. Alloys Investigated Two types of alloys were used in this investigation—zinc-base and aluminum-base alloys. Two alloys of each group were included. Those most generally employed in the industry at present were selected. Alloys A and B are of the same nominal composition, and correspond to A. S. T. M. alloy XXI, containing 4 per cent aluminum, 3 per cent copper, 0.1 per cent magnesium, and the balance zinc of 99.99 per cent

Jan 1, 1932

By Eugene H. Dawson

MICA is a mineral that once was a familiar sight as fireproof windows in stove and furnace doors and as lamp chimneys and shades. Since 1878, the beginning of the electrical age, the use of mica for such purposes has gradually declined and its use in electrical equipment and appliances has developed to such an extent that the known sources of supply are scarcely equal to the demand. With the increasing capacity of electric generating units, the size of mica sheets found in nature was inadequate. However, in 1894, a process was developed whereby thin films or splittings cemented with shellac or other binders could be pressed into large sheets. 18 The introduction of radio in the early 1920s created such a heavy demand for the smaller sizes of mica that on March 22, 1938, mica was included among 23 commodities on the list of strategic materials approved by the United States Army and Navy Munitions Board. To be included in this list, the material must be one whereof the domestic supply is not sufficient to meet the demand. COMPOSITION Mica is a complex mineral composed principally of the silicates of potassium, aluminum, and magnesium. Less prevalent species contain, as essential components, lithium, vanadium, and chromium. Iron usually is present either as an essential component or as an impurity. The mica group comprises some nine different species, five of which, muscovite, phlogopite, vermiculite, lepidolite, and biotite, are widely used in industry. Lepidolite and zinnwaldite (lithium micas) and roscoelite (vanadium mica) are sources of lithium and vanadium. Muscovite, "white mica," is potassium mica. Theoretical formulas H2KAl3(SiO4)3. There are two varieties, distinguished as to color, known in industry as ruby and green. In crystals or "books," the colors each range through varying shades of red and green. However, when split into thin films, all micas, except biotite and phlogopite, are colorless and transparent. Muscovite frequently is stained red or black by thin films of iron oxide between the laminae. The staining usually is derived from magnetite, which sometimes is found as unaltered crystals.

Jan 1, 1949

By Glenn S. Wyman

CHUQUICAMATA, located in northern Chile in the Province of Antofagasta, is on the western slope of the Andes at an elevation of 9500 ft. Because of its position on the eastern edge of the Atacama Desert, the climate is extremely arid with practically no precipitation, either rain or snow. All primary blasting in the open-pit mine at Chuquicamata is done by the churn drill, blasthole method. Since 1915; when the first tonnages of importance were removed from the open pit, there have been many changes in the blasting practice, but no clear-cut rules of method and procedure have been devised for application to the mine as a whole. One general fact stands out: both the ore and waste rock at Chuquicamata are difficult to break satisfactorily for the most efficient operation of power shovels. Numerous experiments have been made in an effort to improve the breakage and thereby increase the shovel efficiency. Holes of different diameter have been drilled, the length of toe and spacing of holes have been varied, and several types of explosives have been used. Early blasting was done by the tunnel method. The banks were high, generally 30 m, requiring the use of large charges of black powder, detonated by electric blasting caps: Large tonnages were broken at comparatively low cost, but the method left such a large proportion of oversize material for secondary blasting that satisfactory shovel operation was practically impossible: Railroad-type steam and electric shovels then in service proved unequal to the task of efficiently handling the large proportion of oversize material produced. The clean-up of high banks proved to be dangerous and expensive as large quantities of explosive were consumed in dressing these banks, and from time to time the shovels were damaged by rock slides. As early as 1923 the high benches were divided, and a standard height of 12 m was selected for the development of new benches. The recently acquired Bucyrus-Erie 550-B shovel, with its greater radius of operation compared to the Bucyrus-Erie 320-B formerly used for bench development, allowed the bench height to be increased to 16 m. Churn drill, blasthole shooting proved to be successful, and tunnel blasts were limited to certain locations where development existed or natural ground conditions made the method more attractive than the use of churn-drill holes. Liquid oxygen explosive and black powder were used along with dynamite of various grades in blasthole loading up to early 1937. Liquid oxygen and black powder were discontinued because they were more difficult to handle due to their sensitivity to fire or sparks in the extremely dry climate. At present ammonium nitrate dynamite is favored because of its superior handling qualities and its adaptability to the dry condition found in 90 pct of the mine. In wet holes, which are found only in the lowest bench of the pit and account for the remaining 10 pct of the ground to be broken, Nitramon in 8x24-in. cans, or ammonium nitrate dynamite packed in 8x24-in. paper cartridges, is being used. This latter explosive, which is protected by a special antiwetting agent that makes the cartridges resistant to water for about 24 hr, currently is considered the best available for the work and is preferred over Nitramon. Early churn drill hole shots detonated' by electric blasting caps, one in each hole, gave trouble because of misfires caused by the improper balance of resistance in the electrical circuits. Primarily, it was of vital importance to effect an absolute balance of resistance in these circuits, the undertaking and completion of which invariably caused delays in the shooting schedule. Misfires resulting from the improper balance of electrical circuits, or from any other cause, were extremely hazardous, since holes had to be unloaded or fired by the insertion of another detonator. The advent of cordeau, later followed by primacord, corrected this particular difficulty and therefore reduced the possibility of missed holes. After much experimentation, the blasting practice evolved into single row, multihole shots, with the holes spaced 4.5 to 5 m center to center in a row 7.5 to 8 m back from the toe. Such shots were fired from either end .by electric blasting caps attached to the main trunk lines of cordeau or primacord. The detonating speed of cordeau or primacord gave the practical effect of firing all holes instantaneously. Double row and multirow blasts, fired instantaneously with cordeau or primacord, proved to be unsatisfactory in the type of rock found at Chuquica-

Jan 1, 1952

By C. G. Dunn, M. Sharp

HE orientations of 137 crystals of copper pro-T duced by secondary recrystallization in a cube texture matrix have recently been obtained. Although the crystals were not prepared for the purpose of determining a secondary recrystallization texture, the orientations obtained proved to be rather interesting, as they confirmed, in part, published results and also disclosed additional preferred orientations in the texture. The investigation of Dahl and Pawlek,&apos; Bowles and Boas,&apos; and Kronberg and Wilson3 showed respectively that the orientations of secondary grains growing in a cube texture matrix were related to those of the primary grains by a rotation of approximately 30" about [001], the rolling direction, by 30" about a <111> direction, and by either 22" or 38" about a <111> direction. Kronberg and Wilson also obtained a component of the texture similar to that of Dahl and Pawlek except the angle of rotation about [001] was 19". When the cube texture matrix was deformed a small amount, Kronberg and Wilson also obtained large grains on subsequent annealing corresponding to a rotation of 15" about the normal to the sheet, but these grains should not be classified as secondary recrystallization grains since they were produced subsequent to mechanical straining. The particular texture obtained, of course, depends on the composition of the copper and the processing schedule employed, since these factors markedly affect the primary recrystallization texture and the sharpness of any cube texture produced. In the present investigation, pieces of OFHC copper in the form of M in. round bars were cold forged to a thickness of about 0.40 in., annealed 1 hr at 350°C in an atmosphere of hydrogen, and cold rolled crosswise to a thickness of 0.200 in. These pieces were given a penultimate anneal of 1 hr at 350°C in hydrogen and a 90 pct cold-rolling reduction lengthwise to a thickness of 0.020 in. Indentations generally were put in one end of the as-cold-rolled strips to promote earlier formation of secondary grains.

Jan 1, 1953

By AIME AIME

MORTIMER ELWYN COOLEY, dean of the College of Engineering and Architecture of the University of Michigan, has been elected president of the American Engineering Council of the Federated American Engineering Societies. This was announced at a meeting of the Executive Board of the Council held at the Cosmos Club in Washington on Sept. 30. Dean Cooley assumes office at once. The new head of organized engineering is a past president of the American Society of Mechanical Engineers and has a long record of distinguished service in education, under the government and in private capacities. He was born in Canandaigua, N. Y., March 28, 1855, and was graduated from the United States Naval Academy in 1878. With his classmate, Dr. Ira N. Hollis, he was ordered to the U.S.S. "Quinnebaug," then fitting out at the Norfolk Navy Yard preparatory to a cruise in the Mediterranean.

Jan 1, 1921

By A. Springer

Chemists, physicists and others, whose occupations necessitate the use of fine scales, have heretofore regretted their inability to obtain any which would remain uniformly accurate. The difference between the theoretical and the actual results obtained in the ordinary balance (provided the pivot-distances are exact) is mainly due to the frictional resistance between the knifeedges and their bearings. This frictional resistance, although reduced to a minimum in the finest scales when new, constantly increases, thereby decreasing the sensitiveness proportionately. When examined under the microscope, neither the surface of the knife-edge nor that of&apos; its hearings ever appears perfectly smooth. Soft kunife-edges are easily blunted, whereas hard ones are brittle and liable to crumble under the effects of over-load or shock. Prof. Frederick A. Roeder for many years attempted to discover some means by ,which the knife-edge could be replaced with some device free from the above-mentioned objections. His experiments convinced him that a torsion-joint was best suited for that purpose. After he had communicated his conclusion to me, we jointly developed the system to its present form. A torsion-wire had been used for the centre of rotation, prior to Prof. Roeder&apos;s invention, but it was found impossible to replace the terminal knife-edges with torsion-joints.

Jan 1, 1884

By Howard Martens

HARDNESS behavior of commercial titanium alloys following various heat treating processes has been studied for some time. However, the hardness of such alloys following a definite measured cooling rate from the single phase region has not been reported. Therefore, a series of experiments was conducted on the three alloys: 150A, 130A, and 130B. The manufacturers gave the following compositions for these alloys: Ti 150A: 0.045 pct C, 0.069 pctN, 1.32 pct Fe, and 2.68 pct Cr; RC 130A: 0.13 pct C, and 7.9 pct Mn: RC 130B: 0.11 pct C, 3.5 pct Mn, and 3.2 pct Al. A method similar to that described by Greninger was used, and the cooling rate varied from 6" to 9200°F per sec. The cooling curves were recorded on a Speedomax or a recording oscillograph, and the hardness was measured on a Tukon hardness tester using a Knoop indentor with a 500 g load. The curves of Fig. 1 show the variation of the Knoop hardness with the cooling rate for these three alloys. The alloys 150A and 130B behave in a similar manner, as shown by the curves. In neither of these alloys was it; possible to retain the high temperature ß phases, even by the most rapid cooling rate. The slow cooling rates produced a typical ß structure in these two alloys. As the cooling was increased, these phalses became more finely dispersed and the hardness increased. This increase in hardness with cooling rate continued for the 150A alloy until a rate of approximately 1000°F per sec was reached. At this cooling rate, the structure showed the result of the dif-fusionless transformation of the ß solid solution to the supersaturated a solid solution which is referred as a&apos;. At higher cooling rates, the structure showed no change and the hardness showed no great change, as indicated by the dotted portion of the curve in Fig. 1. The increase in hardness with cooling rate for the 130B alloy continued until a rate of approximately 300°F per sec was reached. At this rate the structure was produced and the maximum hardness was reached. Higher cooling rates caused no marked changes in hardness or structure. The alloy 130A behaved in a different manner, as shown by the curve of Fig. 1. The structure produced by the slow cooling rates was a typical a+ß structure, which became finely dispersed as the cooling rate increased. The hardness increased with cooling rate and reached a maximum at approximately 120°F per sec. At this maximum hardness, the structure showed the result of the decomposition of the ß phase into the ß + phase structure. As the cooling rate was increased, smaller amounts of the at phase were formed and the alloy became softer. For cooling rates of 3000°F per sec and above, the high temperature ß phase was retained and the hardness of the alloy did not change markedly. Acknowledgment This paper presents the results of one phase of research carried out at the Jet Propulsion Laboratory, California Institute of Technology, under Contract No. DA-04-495-0rd 18, sponsored by the Dept. of the Army, Ordnance Corps.

Jan 1, 1957

By Raymond D. Daniels, Frank E. Rizzo, James D. Gerber

ThIS discussion describes a method for the addition of small amounts of oxygen to columbium (niobium) in an accurate and reproducible manner. The method is based on the complete reduction by columbium of a carefully weighed amount of another metal oxide. The equilibrium Pq associated with Cb-CbO mixtures is extremely low, e.g., 10"25 atm at 100O°C, and the pressures over Cb-0 solutions are even lower. The equilibrium Pq associated with a given metal-metal oxide mixture can be easily obtained, with the aid of a Richardson-Jeffes chart.&apos; Although columbium should effectively reduce almost any metal-metal oxide combination, the proper choice of a metal-metal oxide system is complicated by the low rate of oxygen transport in the gas phase at low oxygen pressures and the difficulty in reducing any columbium suboxide formed during the reduction of the oxygen source material. Thermodynamically, oxide formation on columbium will be avoided so long as the oxygen partial pressure over the columbium is below the equilibrium pressure associated with the mixture Cb-CbO. The logical choice of a source for oxygen would appear to be a mixture of Cb-CbO, since oxide formation would be precluded by nucleation difficulty. But calculations using the kinetic theory of gasses indicate that, for a temperature of 900°C, the reaction would proceed too JAMES D. GERBER, formerly Research Assistant, University of Oklahoma, Norman, Okla., is Research Metallurgist, Air Force Weapons Test Laboratory, Kirtland Air Force Base, N. Mex. FRANK E. RIZZO, Junior Member AIME, formerly Assistant Professor of Metallurgy, University of Oklahoma, is Associate Professor of Metallurgy, University of Texas at El Paso, El Paso, Tex. RAYMOND D. DANIELS, Member AIME, Professor of Metallurgical Engineering, University of Oklahoma, is an NSF Fellow, Institute de MBtallurgie Structurale, Universite de euch:tel, Neuchitel, Switzerland. Manuscript submitted October 28, 1968. IMD

Jan 1, 1970

By R. C. Gifkins

R. C. Gifkins (CSIRO)—In this paper evidence is put forward to support the idea of grain boundary shearing in aluminum at 4.2°K and the phenomenon is explained in terms of a low-temperature "equicohesive temperature". It is stated that these findings show that grain boundary shear cannot be ruled out in any situation by temperature arguments alone. We believe, from our own recent study of "apparent grain boundary sliding&apos;&apos; at temperatures below 0.45 Tm, that it can be ruled out on temperature arguments alone.45 Our experiments were made principally with magnesium and a Ms-A1 alloy ("Magnox A12"). Careful examination of offsets of marker lines or steps at grain boundaries produced by deformation at room temperature (-0.3 Tm) showed many of these to result from curvature over narrow zones along the grain boundaries. A significant residuum did, however, appear as a sharp offset or step. It was found that the mean value of this step rose to a small value during the first 0.5 to 1 pct strain and then remained at this level with further strain. Moreover, exactly the same values were obtained (at the same stress) at 75°C instead of 21°C. That is, in this range of temperature the "apparent sliding" was not temperature-sensitive. At 125°C and above there was sliding which increased with strain and which was temperature-dependent. When this temperature-dependent sliding was used to calculate the sliding to be expected at room temperature, this underestimated the "apparent sliding" by a factor of 104. The conclusion drawn is that the "apparent sliding" consists of shear localized in a zone of a width measured perhaps in microns, whereas it seems that true sliding occurs on the boundary surface.46 A model for such localized shear has been developed in general terms, following a similar model of Urie and Wain.47 Other strong evidence for low-temper- ature sliding has been based on the offsets of marker lines consisting of a substructure seen using the electron microscope to resolve these.48 We have repeated this work and found that the effects can be accounted for in terms of cracks in an oxide film which is produced when the substructure is etched up; these cracks form over zones of shear rather than at actual interfaces. However, in aluminum at room temperature (-0.3 Tm) there is no "apparent sliding" which is optically detectable. We suggest that, when the temperature is much lower (and possibly the rate of strain higher, too), as in the experiments of Chin et al., then aluminum behaves like magnesium at room temperature, and a narrow zone of shear develops to accommodate differences in strain across the grain boundary. Such a zone could well give rise to triple-point cracks. It is hoped to investigate these suggestions further. B. Y. Chin, W. F. Hosford, Jr., and W. A. Backofen (authors&apos; reply)—It is interesting to have Dr. Gif-kin&apos;s comments, although it is somewhat difficult to reply in detail without the reference containing the work that he describes. Apparently though, he does find a low-temperature temperature-independent sliding that would seem to be related to the observations reported here. Perhaps some of the difficulty has semantic origins, growing out of the distinction between (&apos;true sliding" and "apparent sliding".

Jan 1, 1965