Search Documents

By P. T. Bail, J. E. Bobek

In reservoirs containing soft shales interbedded with oil-producing sands, it is possible to have water movement from the shales into the sands during reservoir depletion. This paper presents the results of scaled flow-model tests performed to investigate the efficiency of oil displacement by this vertical influx of water into oil-producing sands. In these model tests, the effects of rate of influx and rock wettability were considered. Oil recoveries by shale-wafer influx and by water flooding were cornpared after 0.4 hydrocarbon volume of water entered the producing sand. This comparison was made for water-wet and oil-wet systems. In water-wet sand, shale-water influx produces slightly less oil than conventional water flooding; in oil-wet sand, shale-water influx produces about one-half as much oil as conventional water flooding. In another type of comparison, it was found that shale-water influx followed by water flooding recovers less oil than water flooding alone. This is true for both water-wet and oil-wet sands. A comparison of tests run at different rates of shale-water influx shows that oil recovery is insensitive to rate in water-wet sand; in oil-wet sand, oil recovery decreases with decreasing rate of influx. INTRODUCTION Localized subsidence of the earth's surface has accompanied the depletion of some oil reservoirs, particularly in California,1, 2 along the Texas Gulf Coast,3 4 and in the Bolivar Coastal fields of Venezuela. Subsidence occurs when fluid withdrawals reduce the pressure in the reservoir. The reasons for subsidence accompanying a reduction in reservoir pressure are not known with certainty.10° However, there is considerable evidence that compaction of soft shale beds adjacent to producing oil sands can be a major cause of this subsi-dence.3, 6, 10-12 When the shales compact, a limited amount of water moves from the shales into the producing sands. A schematic illustration of this oil-producing mechanism is shown in Fig. 1. As the pressure in the sand declines due to oil production, a predominantly vertical pressure gradient develops at the sand-shale boundary. This causes water to move from the shale into the sand as indicated by the solid arrows. This paper reports the results of scaled flow-model tests to investigate the efficiency of oil displacement by the vertical influx of shale water into producing sands. The model tests were not performed with the aim of duplicating the recovery behavior of any specific reservoir. The primary purpose of the tests was to obtain a better understanding of oil displacement by shale-water influx. A knowledge of the oil- and water-production characteristics of even a simplified reservoir system should be of value to engineers estimating the performance of reservoirs where shale-water influx is occurring in conjunction with other production mechanisms. The following limitations and assumptions apply to the model work. 1. The sand of the prototype reservoir is homogeneous and horizontal. 2. The shale-water influx is uniformly distributed along the top and bottom of the sand member being studied. 3. No effects of edge-water drive or dissolved-gas drive that might accompany shale-water influx are considered. PROTOTYPE RESERVOIRS Scaled-model tests were performed to study oil displacement from three prototype reservoir sections. The reservoir sections modeled consist of single sand layers out of a sequence of -sand and -shale layers, as illustrated in Fig. 1. Each prototype represents a homogeneous, high-permeability, unconsolidated sand layer. In the field, the prototype is oriented in such a manner that one end is at the radius of drainage of a producing well and the other end is pointed toward the producing well (Fig. 2). The sand and fluid properties and the dimensions of the three prototypes are given in Table 1. The capillary pressure relationships for the three prototypes are presented in Figs. 3, 4 and 5. The oil-water per-

By S. F. Shaw

IT IS generally recognized that the natural gas absorbed in petroleum plays the leading r6le in moving the oil through the sands to the well and supplies the energy that delivers the oil to the surface when the wells are flowing. It is the purpose of this paper to note the amount of oil that could be lifted by this gas if 100 per cent. efficiency were obtained and the efficiencies actually obtained in the use of this gas. An article in MINING AND METALLURGY,' stated that in a Wyoming field, with a pressure of 300 lb. per sq. in., there would be absorbed 65 cu. ft. of gas per barrel, or 1.55 cu. ft. per gal. of oil. The writer does not know if data have been obtained, by experiment, for pressures beyond those indicated in this article, therefore, for the purpose of illustration, he has projected this curve to obtain figures for pressures greater than 300 lb., although probably experiment will show that the extended line is not quite correct.

Jan 1, 1926

By Frank A. Wardlaw

MY subject covers the effect that recent metallurgy has had on operations at the Utah-Delaware mine. This mine is the old Highland Boy mine of Bingham Canyon, Utah, one that has now been in operation for about 30 years. It was first operated by Messrs. Weir and Newhouse as a gold mine, under direction of the Highland Boy Gold Mining Co. The ore was oxidized gold ore and it was treated on the property in a cyanidation plant. During the process of development, sulfide ore was found assaying about 5 per cent copper. It proved to be the discovery of what is yet the largest sulfide copper orebody in the State. The first shipment was made in December, 1896. A smelter was built in Salt Lake Valley to treat this ore and not long after the property was sold to the Utah Consolidated Mining Co. From 1900 to 1924, the mine was a large producer of direct-smelting ore which averaged for many years 4.5 per cent. copper, then later dropped to 2 per cent. copper. During the years 1912 to 1920, direct-smelting lead ore was also mined. In 1918'and 1919 ore developments at depth showed a decided increase in silica content and a porphyry sill so closely associated with the ore that it was impossible to mine the ore clean and it was found necessary to build a copper flotation Eoncentrator at Tooele. The mill had a capacity of 1000 tons a day and made a recovery of 90 per cent., and would have been responsible for a continuance of profitable operations had it not been for a slump in the copper market and the necessary high cost of mining ore on the lower levels. RESULTS OF SELECTIVE FLOTATION In 1924 the mine was on the point of a shutdown which had all the earmarks of being permanent; it was being operated at a heavy loss and preparations were made to pull the pumps and salvage the machinery. The plant at Tooele was remodelled for selective flotation by the Inter- national Smelting Co. in order to treat custom ores, and incidentally to clean up a possible 10,000 tons of lead-zinc ore which it was thought possible to get in the Utah-Delaware before shutting the mine down. Results were so encouraging that an effort was made to develop more lead-

Jan 1, 1928

By C. S. Finney, John Mitchell

The decline of the beehive coking industry was inevitable, but it had filled the needs and economy of its day. A beehive plant required neither large capital investment to construct nor an elaborate and expensive organization to run. The ovens were built near mines from which large quantities of easily-won coking coal of excellent quality could be taken, and handling and preparation costs were thus at a minimum. The beehive process undoubtedly produced fine metallurgical coke, and low yields were considered to be the price that had to be paid for a superior product. Few could have foreseen that the time would come when lack of satisfactory coking coal would force most of the beehive plants in the Connellsville district, for example, to stay idle; and if there were those like Belden who cried out against the enormous waste which was leading to exhaustion of the country's best coking coals, there were many more to whom conservation was almost the negation of what has since become popularly known as the spirit of free enterprise. As for the recovery of such by-products as tar, light oil, and ammonia compounds, throughout much of the beehive era there was little economic incentive to move away from a tried and trusted carbonization method simply to produce materials for which no great market existed anyway. With the twentieth century came changes that were to bring an end to the predominance of beehive coking. Large new steel-producing corporations were formed whose operations were integrated to include not only the making and marketing of iron or steel but also the mining of coal and ore from their own properties, the quarrying of their own limestone and dolomite, and the production of coke at or near their blast furnaces. As the steel industry expanded so did the geographic center of production move westward. By 1893 it had moved from east-central to western Pennsylvania, and by 1923 was located to the north and center of Ohio. This western movement led, of course, to the utilization of the poorer quality coking coals of Illinois, Indiana and Ohio. These coals could not be carbonized to produce an acceptable metallurgical coke in the beehive oven, but could be so treated in the by-product oven. By World War I the technological and economic limitations of the beehive oven as a coke producer were being widely recognized. After the war the number of beehive ovens in existence dropped steadily to a low of 10,816 in 1938, in which year the industry produced only some 800,000 tons of coke out of a total US production of 32.5 million tons. The demands of the second World War led to the rehabilitation of many ovens which had not been used for years, and in 1941, for the first time since 1929, beehive ovens produced more than 10 pet of the country's total coke output. Production fell off again after 1945, but the war in Korea made it necessary once more to utilize all available carbonizing capacity so that by 1951 there were 20,458 ovens with an annual coke capacity of 13.9 million tons in existence. Since that time the iron and steel industry has expanded and modernized its by-product coking facilities, and by the end of 1958 only 64 pet of the 8682 beehive ovens still left were capable of being operated. Because beehive ovens are cheap and easy to build and can be closed down and started up with no great damage to brickwork or refractory, it is likely that they will always have a place, albeit a minor one, in the coking industry. The future role of the beehive oven would seem to be precisely that predicted forty years ago by R. S. McBride of the US Geological Survey. Writing with considerable prescience, McBride declared: "A by-product coke-oven plant requires an elaborate organization and a large investment per unit of coke produced per day. Operators of such plants cannot afford to close them down and start them up with every minor change in market conditions. It is not altogether a question whether beehive coke or by-product coke can be produced at a lower price at any particular time. Often by-product coke will be produced and sold at less than cost simply in order to maintain an organization and give some measure of financial return upon the large investment, which would otherwise

Jan 1, 1961

Minnesota J. A. MACKILLICAN, Chairman W. W. J. CROZE, Vice-chairman T. L. JOSEPH, Vice-chairman S. E. ATKINS, Secretary-Treasurer, Alworth Bldg., Duluth, Minn. Montana MURL H. GIDEL, Chairman ALBERT E. WIGGIN, Vice-chairman ALEXANDER M. MUDONALD, Secretary-Treasurer, 101 W. Granite St. Butte, Mont. GEORGE G. GRISWOLD FRANCIS A. THOMSON

Jan 1, 1929

By W. M. Ross

AMONG the comparatively few A radical changes in mining equipment in recent years is the introduction and use to an ever greater degree of detachable bits for rock drills. Just how great the possible field for economic application of this innovation is, and to what ex- tent detachable bits are used instead of the conventional type of drill steel, are matters of conjecture. Just as a rough approximation, one might conceive that at least three-quarters of the drilling done in mines today could better be performed by steel with detachable bits, instead of only about one-quarter as at present.

Jan 1, 1939

By R. L. Segall

AN unusual thermal etch figure in copper is described and an explanation in terms of twinning is suggested. A flat polycrystalline specimen of OFHC copper cut from a rolled sheet was electro-polished in orthophosphoric acid and annealed at 950°C in a vacuum of approximately 10-3 mm Hg for 2 hr. The specimen was found to be thermally etched, the markings on the surface being consistent with the assumption that they were the traces of the (111) planes which are developed preferentially because they have the lowest free energy. However, on one grain (the grain shown in Fig. 1) the traces formed an almost regular pentagon and at first sight it seemed unlikely that they could all be (111) traces. These traces were studied further because it was thought that they might be a type of growth spiral. A fringe pattern showed that this was not so, the grain being sensibly flat and the only features having steps were the striations and the faint curved line passing out from the center of the pentagons. To obtain some additional information, the specimen was deformed in tension. The effect of the stress was first to cause the appearance of lines running from the centers to the apexes of the pentagons and then to tilt the five segments so formed. At a much greater stress, appreciable slip appeared on the grain; these effects can be seen in Fig. 2. The micrograph was taken at a fairly late stage in the deformation and the tilting is quite marked. The magnification is the same as in Fig. 1, and although some slip can be seen it could be observed better by varying the illumination and using higher magnifications. In each segment of the grain, slip (which takes place on the (111) planes) was parallel to the side of the pentagon in that segment. The marked changes in direction of slip from segment to segment seemed to be incompatible with the presence of a regular array of subgrains. These results suggest that some of the five segments were twins. If this is so, since the twinning plane in copper is the (111) plane, the radial lines must be traces of the (111) planes on the surface. From the symmetry of the striations about the radial lines, these planes must be almost perpendicular to the surface. The angle between <III>directions in face-centered-cubic copper is 70&apos;32&apos;. If, in Fig. 3, OAB (triangle 1) is taken as matrix and OA, OB are (111) planes viewed edge on, then AB is in the correct direction to be the trace of either of the other two (111) planes on the surface. If triangle 2 is the twin (about the (111) plane perpendicular to the surface and containing OB) of triangle 1, then once again it can be shown that all lines are traces of (111) planes. Similarly, triangle 3 is the twin of triangle 2, 4 of 3, and 5 of both 4 and 1. (The sequence is, of course, quite arbitrary.) However, if this were the case there would be a discrepancy of 7&apos;20&apos; to be accounted for. It is suggested that the faint curved line passing outward from the center of the pentagon represents either a low angle boundary or a sixth small twin. The slight step shown by the fringes at this line might be an indication that the former is the case. This explanation does not account for the coincidence of obtaining a grain whose surface must be so close to (110) and obtaining the curious twinning described previously; it would be of interest to find a specific mechanism for this.

Jan 1, 1958

By W. L. Chu

It was observed that chromized coatings on low carbon steel could be embrittled by cooling slowly through the 475°C range. A higher chromium coating was more susceptible to embrittlement than a lower chromium coating. Coating structure and composition could be correlated with the chromizing process and prior carbon content of the steel. IT was recently observed that during the fabrication of rectangular tubings made with chromized thin gage 1010 steel, a high percentage of these parts were fractured readily in a brittle manner under the light impact-forming load employed. Ensuing investigation indicated the cause for such brittle failures to be the so-called 475°C embrittlement of the chromized coatings. The experimental work and results are briefly reported. Rectangular tube sections of normalized AISI C1010 steel, which had a cross-section of 0.5x1.5 in. and a wall thickness of 0.030 in., were chromized to yield coatings having several ranges of thickness, varying from 0.0005 to 0.002 in. Essentially, the chromizing process is similar to that described by Samuel and Lockington,&apos; which consists of heating the parts in a sealed container at about 955°C for 4 hr in intimate contact with a chromizing mixture* samples in a hydraulic press, and the other employed a simple beam bending test of the flat sides of the tubing walls. Neither, however, was able to differentiate the relative brittleness of samples known to include both the brittle and tough types, since the impact-brittle samples were found to deform readily in a manner similar to the tough ones. Both the tough and brittle samples were studied by reflection microscopy. Observation showed that the microstructures of the steel cores were similar in content and distribution of inclusions as well as in the ferritic grain size. Results of Filar micrometer measurements showed that coating thicknesses+ of the brittle samples averaged 0.0007 in., whereas those of the tough samples averaged 0.0016 in. The micrographs of Fig. 2 illustrate the structural differences between coatings of both types of samples. By dissolving the steel cores in nitric acid, coatings of both the brittle and tough samples were isolated. Simple bending tests showed that coatings of the brittle samples cracked readily at about 90" bend, whereas those of the tough samples could be bent nearly 180° without cracking. The coatings as well as the steel cores were analyzed for carbon and

Jan 1, 1956

By A. M. Nicholas

WheN attempting to lift mill pulp containing a considerable percentage of wolframite, in an ordinary bucket elevator, difficulty was encountered from the tendency of the tungsten minerals to settle, on account of their high specific gravity. Lifts not exceeding 20 ft. (6 m.) could be accomplished without particular difficulty, because there was insufficient time for consolidation of the heavy minerals in the bottom of the bucket; but with higher lifts, the heavy tungsten minerals would settle so solidly that when the bucket turned over at the top of the elevator the contents could be only partially dumped. In this case it was necessary to lift the material a distance of 34 ft. (10m.); hence some means had to be adopted to prevent settling, at least to such an extent that the material could be dumped from the buckets. To reduce the carrying time to a sufficient extent would have required a belt speed of 475 ft. (144.7 m.) per minute, which was not feasible. It was decided to try, by vibrating the belt about midway of its span, to keep the material sufficiently agitated during elevation to prevent settling. Underneath the rising side of the belt was placed a 12-in. (30.48-cm.) idler pulley, 18 ft. (5.5 m.) up in the total lift of 34 ft. The idler pulley was set eccentric by % in. (19 mm.) and it was hoped that the vibration thus imparted to the belt, running at a speed of 280 ft. (85 m.) per minute, would prevent settling in the buckets. It was found that the pressure of the belt on the idler, due to the small inclination of the elevator, was not sufficient to overcome sliding on the idler, and the agitation was insufficient to accomplish the desired purpose. The idler was then connected to the drive shaft of the elevator through an intermediate pulley, gearing down to a speed of 20 r.p.m., so that a positive vibration was imparted to the belt; this imparted enough motion to the belt to prevent settling and the contents of buckets dumped satisfactorily. Protecting Elevator Belts When elevating, from the crusher, a rock which was very sharp and abrasive, considerable difficulty arose from cutting of the belt under-

Jan 1, 1918

By J. L. Huitt, B. B. McGlothlin, J. J. Day

Laboratory tests were made with pure minerals and actual reservoir rock samples to study the effects of hydrothermal (steam m hot water) treatments on reservoir rock properties. These tests showed that hydro-thermal treatment of many reservoir rocks can result in significant rock softening. The softening was attributed primarily to the partial destruction of dolomite and kaolinite and the synthesis of montmorillonite in the presence of excess silica. In many cases, the softening was great enough to cause considerable healing of propped fractures; therefore, a serious reduction in welt productivity could result. In other tests it was found that the addition of ammonia to a hydrothermal treating fluid in a concentration as low as 0.013 Ib/lb of water not only could prevent rock softening but could cause rock hardening. The results of X-ray diflraction analyses of rock samples showed that when ammonia was added to the treating fluid, ammonium-mica and analcite were formed instead of montmorillonite. No significant permeability damage was observed in the sandstones that were subjected to the ammonia-hydro-thermal environment; in some sandstones, permeabifity improvements resulted. INTRODUCTION As the use of steam or hot water becomes more prevalent in well stimulation methods. the need for information on the effects of such treatments on reservoir rock properties becomes increasingly apparent. Several works have been published on high-temperature changes in rock properties,&apos;,&apos; but these are more applicable to in situ combustion operations than to steam or hot water injection processes. The mineralogical literature contains many publications which report on the changes occurring with various pure minerals in hydrothermal systems. A review of this literature denotes the ease with which entirely new, crystalline mineral phases can be synthesized from other minerals in hydrothermal environments at temperatures, pressures and residence times typical of those encountered in oilfield thermal recovery or stimulation processes. Discussions of many of these experiments are given by Deer et al. Grim,&apos; Roy et al., Zen\ and Hawkins.&apos; One of the most significant of these pure mineral studies is the hydrothermal synthesis work of Levinson and Vian" in which montmorillonite was synthesized from naturally occurring minerals; i.e., kaolinite, quartz and carbonate minerals (particularly dolomite). These reactions occurred at 575F in only 2 days and at 300F in 5 days. These results may be applicable to petroleum reservoir rocks since the minerals studied were those which are commonly found in sandstones. Furthermore, the environmental conditions imposed in the studies were very similar to those involved in thermal stimulation of petroleum reservoirs, e.g., steam or hot water injection. Other studies have suggested that weak rocks could be hardened by "electrochemical induration", a process in which an electric current is applied to a clay-containing rock body. These tests can be regarded as hydrothermal treatments since they were conducted in some instances with aqueous solutions and since clay temperatures during the electrical treatment reached a maximum of about 100C. Although a number of studies of the reaction of pure minerals have been reported, very little has been published on the reactions of petroleum rock-hydrothermal systems. No work has been reported on preventing the more detrimental rock changes in rock softening which might occur during the injection of steam or hot water into reservoirs. The studies described in this paper were conducted to provide such information. EXPERIMENTAL APPROACH The laboratory tests included studies of the effect of hydrothermal treatment on core samples from several different reservoirs. The hydrothermal treatments (simulated steam treatments) were conducted with distilled water at 575F, for the most part, for periods of 2 to 6 days. This temperature level was selected because it represented that temperature which would probably prevail in several cases under consideration for steam injection projects. The core samples, as well as the pure mineral samples, were contained in high-pressure stainless steel, autoclave-type pressure vessels. The effects of the hydrothermal treatments were evaluated by measuring the penetrometer hardness, formation rock embedment strength and permeabilities of the core samples before and after the treatments (Fig. 1)&apos;" In addition, the mineralogical changes in the specimens were studied by X-ray diffraction. Concomitant with the core sample studies, the mineralogical changes were studied in greater detail by conducting hydrothermal synthesis experiments with pure minerals at similar temperature levels and residence times. For the most part, samples of finely-crushed pure dolomite.

By J. J. Frawley, W. J. Childs

PREVIOUS studies have shown that if a supercooled liquid metal was perturbed by vibration the probability of nucleation is is During a recent investi- gation to determine quantitatively the amount of energy needed to cause nucleation in a given supercooled liquid specimen, it was found that at low-energy values in the megacycle range, below the threshold energy value for cavitation, the amount of dynamic supercooling was greater than the amount of static supercooling. That is, if a specimen had a given amount of thermal supercooling under static conditions, its thermal supercooling could be increased by the addition of low-energy sound waves. The material used in this investigation was high-purity bismuth. This material was chosen because of its low melting point and the high degree of supercooling which could be easily obtained. The sound gener- ator employed in this work was a commercially built Sperry ultrasonic testing unit. This unit was equipped with a barium titanate crystal as a piezoelectric transducer. These sound waves were transmitted to the supercooled melt by a Pyrex rod, as shown in Fig. 1. The transducer was coupled to this Pyrex rod wave carrier by motor oil. The Pyrex wave carrier was approximately 1.5 ft long to prevent damage to the transducer by heat. The diameter of the Pyrex wave carrier appears to be critical. In the initial tests a wave carrier of 0.5 in. in diam was employed. However, the sound waves had no effect on the amount of dynamic supercooling. When the diameter of the wave carrier was increased to approximately the inside diameter of the Pyrex crucible, the sound waves were more effective. Approximately 200 g of metal was melted under a stannous chloride flux in a 30-ml beaker by induction heating. The temperature was recorded by a Pyrex-encapsulated chromel-alumel thermocoule which was placed in the beaker after the bismuth melted. The Pyrex wave carrier was immersed slightly below the surface of the liquid bismuth and the specimen was reheated to about 500°C. It was observed that the amount of supercooling depends on the amount of superheating the specimen receives; therefore, for meaningful results the amount of superheating was the same for all heating cycles. The specimen was allowed to cool in air and the change in temperature was continuously monitored with a potentiometric strip-chart recorder.

Jan 1, 1969

By O. B. Bennett

WHEN diamond drilling was introduced in the Rhokana mines in 1939 it was used principally for pillar removal and for completion of the upper portions of shrinkage stopes which were being affected by increasing pressure. This method of drilling long blastholes proved so successful that it was extended gradually to cover stoping, pillar recovery, and hanging cave work. BY 1949 virtually all the ~roduction of Mindola and Nkana was being obtained by this method. At the present time 87,500 ft are drilled each month by the 80 diamond drills in daily operation. Responsibility for control and issue of diamond drilling equipment and crowns, as well as tabulation of all performance figures, was taken over by a sPecially formed Roto drill department, which also investigated the problems encountered with this new method. To assist this department a fully equipped test chamber, Fig. 1, was established underground where performances of various types of machines and equipment could be studied under conditions as nearly uniform as possible. Since the establishment of this department, which was eventually taken over and incorporated into the study department, considerable experimental work has been done on every aspect of the subject. The problems can be classified broadly under four headings: improvement of drilling equipment, crown design, machines, and stoping layouts. One of the major problems with drilling equipment has been to eliminate vibration. Owing to flexing of rods in the hole, severe friction is set up on the back end of the &apos;Ore barrel and On any high spots in the rods, inducing harmonic vibration in the string of rods and causing the crown to chatter against the face. This not only causes premature crown failure but also reduces penetration speeds and increases wear on the machines and rods used. In the early days, when only holes of EX size were drilled, vibration was largely overcome by periodic greasing of rods and core barrel during each run, but with the change-over to the larger BX hole it became obvious that application of grease by hand was inefficient and time-consuming, and attempts were made to perfect a self-lubricating core barrel. A series of these core barrels was made up and tested and a number of the latest type were used under normal operating conditions, but although footages up to 120 ft were drilled without refilling the overall performance was inconsistent, and the idea was shelved in view of the success of the stabilizer rods referred to later in this paper. At the same time tests were made with barrels 5 ft and later 6 ft long instead of the normal 2 ft. Although a slight improvement was noticed, greasing was still necessary. It was found that rod vibration increased as the core barrel became worn, and in an early test chamber experiment crowns drilled with a worn core barrel averaged 95 ft with a diamond loss of 4.76 carats, whereas the same type of crowns with a new barrel averaged 228 ft with a diamond loss of 3.13 carats. until then all BX drilling had been done with B-sized rods, but during a test on a string of BX-sized rods it was noticed that vibration was negligible. Because of the larger surface area of metal bearing on the sides of the hole, however, the friction and resistance of rods of this size rendered them impracticable on any but the most powerful of the machines, The use of stabilizers spaced evenly along the rods was the next logical step, and for this B couplings, see Fig. 2, were set with three tungsten carbide inserts 1 in. long placed around the periphery equidistantly and at an angle of 45" with a right hand lead. These were placed immediately behind the core barrel and then at 12-ft intervals, as it was found that vibration still occurred when the stabilizers were more than 15 ft apart. The effect of these stabilizers was immediately noticeable; holes were drilled with a minimum of vibration, penetration speeds were improved, and as it was no longer necessary to grease the rods there was a marked decrease in the overall drilling time for each hole. While tests were being made with the stabilizer comeb periodic were taking place with a set of tapered threaded rods, and because there was marked improvement in efficiency it was decided to incorporate the stabilizers and tapered threading in all new rods ordered for Rhokana. The feature of these rods is that only four full turns are required to tighten the coupling as against nine for the present type of B rods. Also, as they are self-centering it is virtually impossible to crossthread them. Each rod has a male 5" tapered Acme thread, Fig, 3, on one end and a female at the other, so that separate couplings are unnecessary, and every fifth rod has an

Jan 1, 1955

By F. E. Rizzo, L. R. Bidwell, D. F. Frank

THE use of galvanic cells for the determination of oxygen activities has spread rapidly since the suitability of calcia-stabilized zirconia as a solid electrolyte material was first demonstrated by Kiukkola and Wagner.&apos; In many of these investigations:-7 including several at ARL, the free-energy changes for various oxidation-reduction reactions involving the oxides FexO, NiO, and Cu2O have been measured as a means of assuring that a cell apparatus is functioning properly. As a result, a large quantity of data pertinent to the calculation of the high-temperature standard free energy of formation (?GO) of these oxides has been accumulated. AGFexo has been carefully measured in many independent investigations, using a variety of techniques, and consequently is accurately known. chipmans has used this informa-

Jan 1, 1968

By H. P. Greenwald

IN the year just passed the Coal Division&apos;s Committee on Rock-Dusting reviewed the status of this safety measure in American coal mines and prepared a paper thereon which will be presented at the February meeting of the Institute. This paper supplements one appearing in Vol. 139 of the "Transactions," page 87 (1940). Because that paper will be issued soon, only a summary is given herein.

Jan 1, 1944

By E. W. Stewart, G. P. Conard, J. F. Libsch

The effects of several additives upon the reduction characteristics of hydrogen-reduced ferrous formate are described. The various additives inhibit sintering of the reduced iron particles by apparently different mechanisms. The magnetic properties of the low density compacts produced from the resulting ultra-fine iron powders were improved markedly. THE permanent magnetic characteristics of ultra-fine iron powder prepared by various means have been a subject of considerable interest and experimentation in the past few years. When such particles are small enough to show single domain behavior, they possess&apos; 1—permanent saturation magnetization, and 2—high coercive force. In the absence of domain boundaries, the only magnetization changes in a particle occur through spin rotation which is opposed by relatively large anisotropy forces. With decreasing particle size, the coercive force tends to increase to a maximum and then decrease because of the instability in magnetization associated with thermal fluctuations. Kittel&apos; has calculated the critical diameter at which a spherical particle of iron can no longer sustain domain boundaries or walls to be approximately 1.5x10-&apos; cm. Stoner and Wohlfarthr in England and Neel4,6 in France have shown from purely theoretical calculations that the high coercive force expected from single domain particles is dependent upon crystal anisotropy, shape anisotropy, or strain anisotropy contributions. Further work by Weil, Bertaut,&apos; and many others has contributed much to the understanding of fine particle theory. Neel and Meikeljohn" have demonstrated that a decrease in particle size below a critical value of approximately 160A leads to a quite rapid decrease in coercive force because of the prevention of stable magnetization by thermal agitation. Lih1, working with powders prepared by the reduction of formate and oxalate salts of iron, has shown the marked influence of powder purity upon magnetic properties. Maximum coercive force was obtained in powders of approximately 65 pct metallic iron content while the maximum energy product, (BxH) occurred in powders of 85 pct metallic iron content. Careful consideration of the preceding theoretical considerations and experimental results has led to the manufacture of permanent magnets from ultra-fine ferromagnetic powders by powder metallurgy techniques. Such work has been done by Dean and Davis," the Ugine Co. of France, and Kopelman." The aforementioned work of Kopelman and the Ugine Co. was concerned somewhat with the effect of various additives upon the properties of hydrogen-reduced ferrous formate. Virtually no work, however, has been published on the effects of additives on the reduction rates of metal formates, although unpublished work by Ananthanarayanan16 howed promise of improved energy product in ultra-fine iron compacts prepared by the hydrogen reduction of a coprecipitated mixture of magnesium and ferrous formate. After consideration of the preceding information, it was hoped that a better balance between the metallic iron content and particle size of the reduced iron powder could be accomplished by a prevention of the attendant sintering of the partially reduced iron powder during the reduction reaction. It appeared possible that magnesium oxide might interpose a mechanical barrier between adjacent iron particles and prevent their sintering together, while metallic cadmium and metallic tin would interpose a liquid barrier which might accomplish the same purpose. The degree to which these materials were effective in accomplishing the foregoing objective and the experimental details associated with the work are reported in the following sections of this paper. Experimental Procedure Preparation of Formate and Oxide Mixtures: To obtain ferrous formate of reproducible reduction characteristics, a slight modification&apos; was made in the technique of Fraioli and Rhoda." A supersaturated solution of ferrous formate was mixed with an equal volume of 95 pct ethyl alcohol and the formate crystals precipitated by stirring and screened to —325 mesh. These crystals were in the shape of elongated hexagons, approximately 4x10 micron in dimension. Various preparations of such ferrous formate, designated as lot 111, were reduced for 2 hr, yielding ultra-fine iron particles of exceedingly reproducible size, metallic iron content, and magnetic properties. The magnesium and cadmium formates were prepared by the reaction of dilute formic acid with their respective carbonates, while the tin formate was prepared by the reaction of dilute formic acid with stannous hydroxide. To evaluate the effect of metallic formate additives in intimate mixture with the ferrous formate, varying amounts of magnesium, cadmium, and tin formates were coprecipitated with the latter. The designations of these materials and their chemical compositions are given in Table I. Due to the differing solubilities of the various formates in aqueous media,

Jan 1, 1956

Jan 1, 1947

Jan 1, 1947

By TENNEY C. DeSOLLAR

TRADITION tells us that the earliest use of Alabama iron was to make shoes for the horses of General Andrew Jackson and his men during the first part of the nineteenth century. The first recorded incident in the making of iron was the request of U. S. Indian Agent Benjamin Hawkins "that a crew of blacksmiths be sent to the Creek Nation in the lower Mississippi territory." These frontiersmen made up the first body of pioneer iron makers in the territory. The first known blast furnace was built by Joseph Heslip in 1818 at Russellville, named after Major William Russell, who was General Jackson&apos;s chief of scouts. The Tannehill furnace was built in 1830 in what is now Tuscaloosa County and its ruins, as shown above, can be seen today.

Jan 1, 1937

By B. Heide, A. Bergrnann

The Meggen mine and the concentrator plant of the Sachtleben Bergbau GmbH are located in the southern part of the Ruhr district of the Federal Republic of Germany. The mine has been in operation for more than 100 years, but the concentrator described in this paper was started up in January 1963. The Meggen orebody is of sedimentary origin and occurs in a zone of limestones, graywacke and shales of Devonian age. The average thickness of the deposit is 3 meters and due to an intense folding of the area, the mineralized zone dips steeply at 80º towards the north.

Jan 6, 1973

By A. Bauer, P. Calder, N. H. Carr, G. R. Harris

Smallwood mine is part of the Iron Ore Company of Canada&apos;s Carol Lake operation and is situated in Labrador, 240 miles north of Sept-Iles, Quebec. Last year, 15 million tons of crude ore were crushed to yield 6.3 million tons of concentrate and pellets. This year the figures will be 17 million of crude and 7 ¼ million tons of concentrate and pellets, which is the full plant capacity. Carol Lake ores consist primarily of specularite and magnetite mixed with quartz. Since both rotary and jet piercing drills are used, it is often desirable in planning to know in which regions of the orebody, or new orebodies, a particular drill will be most economic. This makes it necessary to establish a correlation between drillability and pierceability and some physical rock property. For the rotary drills a good correlation was found with penetration rate and grinding factor index. The jet piercers were found to have a reciprocal relationship in the sense that the best rotary ground was the worst jet ground and vice versa. It is also indicated how an economic comparison could be made using these penetration rate versus grinding factor index curves, the hole size distribution curves for single pass and chambered holes, and the mine distribution curve for grinding factor index.

Jan 9, 1965