Search Documents

By W. L. Martin, J. N. Dew, H. B. Steves, M. L. Powers

This paper presents and discusses the results obtained during a pilot test in the Loco field in southern Okla homa. The test was conducted in a 2%-acre pattern that was part of a 20-acre conventional waterflood pilot area. The conventional flood was well past its economic limit when the hot waterflood was initiated to obtain technical information and operating experience. Temperature data from nine observation wells showed that about 75 percent of the pattern was affected by heat, and that heat losses were severe in the pilot pattern. About 60 percent of the injected heat was lost to overburden and underburden zones during hot-water injection. Wellbore heat losses were held at tolerable levels at the shallow depth of the test by providing a low-pressure air annulus between the injection tubing and well casing. Hot water provided water injectivity increases of 200 to 400 percent. The hot water channeled across the lower portion of the oil sand in three directions through zones of relatively high water saturation. There was no conclusive evidence that natural fractures or pressure partings aflected the flow of fluids in the pilot pattern; however response undoubtedly was aflected by localized pressure gradients and by injection-production rate ratios. The results showed that hot waterflooding increased oil recovery in a reservoir containing 600 cp oil. The total tertiary oil production from the pilot pattern area was 3,896 bbl or about 156 bbl/acre-ft swept by heat. The corre.sponding WOR was about 34:I. Description of the Hot Waterflood Process To hot waterflood an oil reservoir, water is injected that has been heated to a temperature substantially higher than the original reservoir temperature, but lower than the vaporization temperature of water at the prevailing pressures. In the reservoir the hot water flows continuously into cooler sand and rapidly loses heat to the sand until it has been cooled to the original reservoir temperature. Thus, a heated zone and a region or "bank" of cooled water begins to accumulate immediately after hot water injection is started. This bank of cooled water continues to grow ahead of the heated zone, which also grows, but at a slower rate. This occurs because heat transfer is almost instantaneous, and the ratio of heat capacities of water to rock is such that two or three unit PV of hot water must be injected to heat a given unit bulk volume of the reservoir. The primary displacement mechanism is the same for both hot and conventional cold waterfloods; i.e., "piston" displacement occurs at the original reservoir temperature. The incremental benefits of hot waterflooding usually occur long after the breakthrough of cold water at producing wells, and the increased oil recovery necessarily is accomplished with high WOR's (water-oil ratios). Heat decreases the viscosity and density of oil and water. These effects result in more rapid and increased recovery of secondary or tertiary oil. If the cost of the required heat is low enough, the ultimate oil recovery of a hot waterflood should be increased substantially over what would be expected at the economic limit of a conventional cold waterflood. The economic benefits of any hot-fluid injection project depend primarily upon the cost of the heat required to produce more oil at an increased rate. This cost depends in part upon the amount of heat lost to surrounding formations. Heat loss depends upon reservoir thickness, water injection rate and temperature, the depth of the formation, well spacing, and the characteristics of the reservoir rock and surrounding formations. In general, percentage heat losses decrease as injection rate and reservoir thickness increase. Although it is an old idea, hot-water injection has not received widespread field application in the oil industry as a drive process. Much of the original field work with hot water was done in Pennsylvania fields where water permeabilities and injection rates are low. In these cases, hot-water injection was used primarily as a means of increasing in-jectivities — not as a recovery process. Ramey' recently has published an excellent review of the development of hot fluid injection processes. Recent publications"' and our own experiences now indicate that hot water or steam injection also can effectively increase the oil recovery from reservoirs containing viscous crudes. However, the economics of these methods as displacement processes have not been established. Several theoretical predictive techniques have been published (for a review see Ramey'), but simplifying assumptions make

Jan 1, 1969

By Louis D. Huntoon

AFTER the completion, in 1905, of the Hammond Mining and Metallurgical Laboratory of the Sheffield Scientific School, Yale University, it became necessary to secure and assay a large assortment of ore-samples, and to arrange the results in such a manner as to admit of use with the least amount of work on the part of the instructor. At first, pulp-samples, together with their respective assays, were secured from the mines, smelters, and public assayers, but this practice did not prove satisfactory. It was not only difficult to secure a sufficiently large supply of material, but it was also impossible to secure the proper assortment required for instructing students. It involved considerable work for the donors to select the samples and furnish a record of the assays, and also for the instructors to examine each pulp and determine its character. Some of the samples did not contain a sufficient quantity of pulp for the student to check his work in case his first assay did not correspond to the record. In order to increase the number of samples and to vary the character of the material, pulp-samples were later mixed with barren rock and with sulphides, but this method also was unsatisfactory and has been discontinued. At present., small lots of ore are secured by gift or purchase from engineers, public assayers, and the managers of mines, mills, and smelters. These lots weigh from 10 to 100 lb. each, and are rarely finer than 0.25 in. in size. The larger samples permit of a careful study by the instructor in order to determine the best method of assaying to be followed. In universities in which assaying is taught the record of the samples should fulfill the following requirements

Nov 1, 1909

By J. Redstone, A. R. Laplante

Sidbec-Normines operates six large iron ore concentrate regrinding mills in parallel and open circuit at its Port-Cartier pelletizing plant. Grinding kinetics in these mills were characterized for slurry densities varying between 70 and 89% solids, using a lumped parameter size discrete model. Optimum grinding conditions were encountered at 83.5 to 84% solids. Higher densities decreased the normalized selection function and increased slurry short-circuiting, yielding a sharply coarser mill discharge. At lower slurry densities, the normalized selection function decreased and the mill discharge coarsened slightly. The grinding kinetic model predicted particle size distributions within the mill. These were found to vary significantly from the feed to the discharge end. This is likely to cause nonlinear breakage kinetics.

Jan 1, 1985

By R. M. Goldhoff, H. J. Beattie

The high-temperature properties of a 1 Cr-Mo-V forging steel are described. A series of controlled heat treatments was designed to delineate the effects of austenitizing and tempering treatments, temile strength, and grain size on such properties. Studies indicate that the mechanical properties and their varlations under creep can be described by the initial metallurgical structures and their changes droPirzg exposure, particulavly the carbide reactions. Such structures are described and correlated with the mechanical properties. FOR many years the large steam turbine industry has relied on the 1 Cr-Mo-V type forging steel for critical applications. Because of its adequate heat resistance and relative economy, it is currently in use in the temperature range up to about 1050" to 1075°F. Attempts to understand the large property variations attainable in this steel involve the structural modifications due to the wide latitude in its heat treatment. The heat treatment essentially involves a two-step process which includes solution-ing of carbides in the austenite range followed by a suitable tempering treatment below the critical to adjust the level of properties. The latter step is referred to as "secondary hardening" and is basically an ordinary aging reaction involving carbides. In the commercial heat treatment of large components of such steel, homogenizing and stress-relief anneals may be included and have some importance in determining subsequent properties. Several studies of the engineering properties of this steel as a function of transformation micro-structure have been reported.1 3 However, in this steel the carbide reactions, which are a function of composition and heat treatment, appear to be the property-controlling factor rather than the micro-structure defined as a transformation product. Thus, the tempering resistance of this type of alloy steel is mainly a function of the size and distribution of alloy carbides.4 However, it is also necessary to consider the stability of the microstructure and the effect of dynamic carbide reactions on subsequent properties. It is the purpose of this paper to show the interdependence of properties and corresponding structures, particularly carbide reactions, developed for a limited set of controlled heat-treatment conditions applied to 1 Cr-Mo-V steel. MATERIALS AND PROCEDURE The material for this work came from a large production forging whose chemical composition is shown in Table I. The property data accumulated on this steel as a function of heat treatment were room-temperature tensile and smooth- and notch-bar creep rupture at 1050°F (notch geometry: shank diameter = 0.357 in., depth = 50 pct, radius = 0.005 in.). To achieve controlled structural variations the temperature and time of both austenitizing and tempering were varied in a manner to produce a series of eight steels each at one of two grain sizes and one of two hardness levels in proper combination for valid comparisons. This will be clear upon examination of Table I. Structural studies involved the use of optical and electron microscopy as well as X-ray and selected-area electron diffraction. To reveal the nature of carbide precipitations, electrolytic extraction techniques were used with subsequent analysis of the residue by X-ray diffraction. Weight losses of the steel specimens during electrolysis were measured and successive chemical fractionations of the residues were applied and checked by X-ray examination. The details of fine structural distributions, morphologies, and crystallography of the precipitates as well as dislocation distributions were investigated by examining in the electron microscope three common types of preparation. a) Relief Replicas. Mechanically polished sections were etched in 2 pct nital, replicated with a nitrocellulose film, which was shadowed by chromium vapor deposited at a glancing angle of 20 deg. b) Extraction Replicas. A thin film of carbon was vapor-deposited on the polished and etched surface. The carbon films were then etched off and gathered on electron-microscope supporting grids. The carbides left imbedded in the carbon replica in their original distribution were then examined crystallo-graphically by selected-area electron diffraction. c) Thin Films. Specimens were mechanically ground and polished down to a thickness of 0.001 to 0.003 in. Final thinning was done electrolytically in a "chrome-acetic" electrolyte. When holes began to appear in the foil, the voltage was interrupted and applied in several 1-sec bursts. Sections of the foil between holes were thin enough to pass a 100-kv electron beam that carries an image.

Jan 1, 1965

By Milton C. Neul

As recently as the mid-1930's, steam and rail haulage were still the primary means of moving large quantities of rock. However, 2- to 5-ton standard on-highway trucks were beginning to be used in the mining industry's efforts to lower haulage costs. It was quickly obvious that rubber-tired equipment was more flexible, faster and more maneuverable. The trend towards haulage trucks had begun. Now while savings were being realized, the severe operating conditions encountered in open pit operations proved too much for the lightly constructed frames, gasoline engines and highly inflated tires. As a result, a few years later, the first 10 to 15-ton, two-axle heavy duty trucks were designed specifically to operate under off-highway conditions.

Jan 3, 1966

By S. A. TAYLOR

AN EDITORIAL on the Strike Situation in the Coal mining industry in the New York Evening Post of Nov. 4, 1919, gave what purported to be statistics of the Department of Labor, for a period of two weeks, which showed an average for the year, based on these two weeks, of 32% hours per week. This mode of arriving at the number of hours per week, while not accurate, is not so far off from the facts as to call for any special comment. The report of the U. S. Geological Survey, Department of Coal Statistics, give so the number of days worked in 1917 as 243; reducing the same to hours per week, assuming 8 hours per day, shows a weekly operation of mines at an average of 36J4 hours. But this assumption is not exactly correct, for the reason that it is not very often that the miners work the full 8 hours per day. There are many explanations for this, but it is not pertinent to this statement to discuss them now, as the important thing to consider is whether a 30-hour week would be for the best interest of not only the men themselves, but the public or country in general.

Jan 1, 1920

By R. F. Stewart, A. W. Hall

A method has been developed for continuously measuring the moisture content of coal. The method is based on the thermalization of fast neutrons by hydrogen in the coal. Neutrons from a small radio-isotope source penetrate the coal, are scattered by hydrogen, and measured by a thermal neutron detector. The number of thermal neutrons counted can be directly correlated with the moisture content of coal. In a pilot-scale system, moisture was measured continuously within 0.2% in coal moving at rates up to 20 tph. The method is adaptable in industry for continuously measuring the moisture content of coal at high tonnage flow rates. Such an application would permit continuous recording of moisture in coal without sampling and facilitate quality control. An automatic and continuous method of measuring the moisture content of coal is needed by the coal industry. Automatic control of the coal quality would reduce the cost of coal preparation, improve the product, and thus indirectly increase the use of coal. Moisture in coal can be determined by several methods, but the time required to obtain samples and analyze them by existing methods makes it difficult, if not impossible, to control the quality of the product. Both producers and consumers need a method for continuous and instantaneous measurement of moisture content without sampling in order to regulate process equipment and keep the moisture content of coal within specifications. At the Morgantown, W. Va., Coal Research Center we are developing a nuclear method for continuous measurement of moisture in coal. This method is based on the thermalization of fast neutrons by hydrogen in the water and organic matter of coal. Neutrons from a small radioisotope source penetrate the coal, are scattered by hydrogen, and are measured by a thermal neutron detector. The number of thermal neutrons counted can be directly correlated with the moisture content of coal. Design of a moisture meter based on neutron thermalization depends on many variables, any or all of which can affect the sensitivity of the meter. These factors include those related to the nuclear aspect; type and size of neutron flux and source, type of detecting device, and background count; and those related to the coal being tested: rank, particle size, and ash content. A survey was initiated to eliminate the relatively insignificant factors and to ascertain the magnitude of the major effects. Such information was necessary to fully evaluate the technique and to establish design criteria. Coal contains a relatively large amount of hydrogen in the organic coal substance and the water of hy-dration of the shaly material as well as in the moisture. To apply this concept of moisture measurement to coal requires that the organic substance in coal from any one seam of a particular mine be uniform in hydrogen content. The difference in total hydrogen content of wet and dry coal is relatively small, so that a moisture measurement based on this concept requires a measurement between two large numbers to a high degree of precision. Thus, it was necessary to develop a highly precise instrumentation system for continuous measurement and to obtain a physical arrangement permitting measurement of moving coal with a minimum effect from density variation. EXPERIMENT WITH TRAYS OF COAL Tests were conducted with metal trays containing SO to 100 lbs of coal to develop an instrument system of high precision. A scaling system with a maximum instrument error of 0.2% was used to test different types of thermal neutron detectors. The most suitable type of detector was a boron-10-lined proportional counter tube. While this type of detector showed satisfactory stability, extensive testing disclosed a long-term count reduction probably due to some type of deterioration in the detector. However, development of an electronic system using dual detectors eliminated this deterioration as a serious problem. (The second detector would be used to measure a reference drum of dry coal — the difference in count rate between the wet coal and dry reference coal being a direct measure of moisture content.) Table I, column 1, shows typical results with a 1-curie plutonium-beryllium neutron source and a thermal neutron detector beneath a tray of coal and illustrates the precision of measurement. Consecutive measurements (indicated in Table 1, columns 2-5) of thermal neutrons at various times and positions be-

Jan 1, 1968

By M. R. Tek

General equations relating the pressure drop necessary to sustain the flow of a fluid through a porous matrix at a given rate have been developed. The results indicate that at high values of flow rate the pressure-flow behavior may not necessarily satisfy the usual Darcy equation. The mathematical analysis, carried through the micro-pore geometry and extended through the macro-reservoir scale, indicate that Darcy's law, of limited applicability to certain ranges of Reynolds numbers, can be generalized through the inclusion of some additional parameters. The "generalized Darcy equation" has also been formulated in dimen-sionless form permitting the evaluation of its predictive accuracy with regard to literature data. A comparison between predicted and experimental values indicates that the generalized Darcy equation predicts the pressure drops with good agreement over all possible ranges of Reynolds numbers. INTRODUCTION The limits and the nature of validity of Darcy's law' has been a subject of every-day interest to the industry for many years. It is well known that as the Reynolds number, characteristic of the fluid flow through porous media, becomes large, Darcy's law gradually loses its predictive accuracy and ultimately becomes completely void. For the last 20 years much has been said and written on this subject. Unfortunately little has been accomplished to bring about a satisfactory agreement, at least on the nature of the threshold of validity of Darcy.'s law. Fluid dynamists, geo-physicists, and engineers all had their individual views, explanations, interpretations and concepts on the subject. To some, a mechanistic analogy with pipe-flow proved a satisfactory explanation.' To others,' turbulence, in its random character, was incompatible with the geometric structure of consolidated porous systems. To some,4 turbulence merely represented a factor influencing the permeability measurements and again to others5,6,7 em-pirical or semi-empirical correlations proved satisfactory from an engineering viewpoint. Deviations from Darcy's law at high flow rates have been studied by systematic experiments by Fancher, Lewis, and Barnes.' In an article on the flow of gases through porous metals, Green and Duwezs conclude that the onset of turbulence within the pores appears unsatisfactory to explain deviations from Darcy's law. This view is held by many others. While the subject remained controversial for many years, the development of vast natural gas reserves throughout recent years further justified considerable interest on this problem from the standpoint of gas reservoir behavior. As large amounts of field data became available from the operation of many gas fields, it became evident that the steady-state behavior of gas wells was not, in general, in agreement or compatible with Darcy's law. This suggested a careful reconsideration of all mechanisms which may account for pressure drops in addition to viscous shear. In a series of articles9,10 . Hou-peurt indicated that deviations from Darcy's law may be explained on the basis of kinetic energy variations and jetting effects without resorting to assumptions on turbulent flow conditions. Another article by Schneebeli11 indicates that special experiments by Lindquist clearly demonstrated that the onset of turbulence does not necessarily coincide with conditions of deviation from Darcy's law. This view is also held by M. King Hubbert.12 Starting with the basic pressure-flow relations suggested by Houpeurt, the derivation, development and extension of analytical expressions to -supplement and generalize Darcy's law has been the objective of this work. MATHEMATICAL ANALYSIS Derivation of Dimensionless Pressure-drop, Flow-rate Relations In considering the flow of a fluid through a porous matrix geometrically represented by a succession of capillary passages in the shape of truncated cones,810 an approximate expression may be derived relating viscous and inertial, i.e., total pressure drop to the physical properties of the fluid, geometric properties of the rock matrix and the rate of flow: ?P/?r = µ/k V [ 1 + c(m4 - 1) p V/16n" mµ w] ..........(1) Let us formally set: c (m4 - 1) / 16n" m = a d ......(2) Such a representation is equivalent to assert that the term [c(m4 — 1)/ 16n"m], variable with various porous media and probably highly variable within a given porous medium, may be macroscopically defined as equal to a lithology factor times the aver-age grain diameter d. In view of the usual grain and pore size distribu-

Jan 1, 1958

By E. P. Pfleider, Rolland L. Blake

IT is generally believed that the amount of diamond drilling will increase appreciably in the next decade, as the seaarch for minerals throughout the world becomes more difficult and intense. An attendant problem may be one of short diamond supply, resulting in higher bit and drilling cost. With this background, the U. S. Bureau of Mines' and the School of Mines at the University of Minnesota' have established comprehensive research programs in diamond drilling. One of the several aims is the design of a more efficient bit, which would lower diamond consumption and increase rate of advance, both essential in reducing drilling costs. The objective of the specific research problem" discussed in this paper was an investigation of the cutting action of the cliamonds set in a diamond drill bit, cutting action meaning the manner in which the diamonds cut or. loosen the minerals in the rocks being drilled. In the literature on cutting action such descriptive terms are used .as: grinding, wearing, cutting, breaking, shearing, scraping, melting, and chipping. These actions were seldom described or defined. Grodzinski describes the cutting action of a single diamond in the shaping of certain types of material as "breaking out chips of the material." Brittle mate-. rials break as small separate chips, and tough materials, because of heat generated, give a continuous chip. Deeby said about diamond drills: "When diamonds are forced into the formation and rotated, they either break the bond holding the rock particles together, or they cause conchoidal fracture of the rock itself. The former action occurs when drilling in sandstones, siltstones, shales, etc. and the latter action when drilling in chert, flint, or quartz." He said that diamonds cut on the "grinding principle" but he does not define or elaborate on this action. The cutting action of diamonds on glass was first investigated about 1816 by Dr. W. H. Wol-laston, an English physicist. The best glass-cutting diamonds have a natural or artificially rounded cutting edge. This edge first indents the glass and then slightly separates the particles, forming a shallow and nearly invisible fissure. Since none of the material is removed, this action is one of splitting rather than cutting. No other reports of research work on the cutting action of the diamond were found, and further work was considered justified and advisable. It is impractical, even if possible, to observe directly the cutting action of a diamond drill bit in rock; therefore it was necessary to devise an indirect method. It was believed that a study of the following three observations would lead to a better understanding of the cutting action: 1—the appearance of the minerals or rock surface in the bottom of the hole, 2—the size, shape, and other characteristics of the drill cuttings, and 3—the condition of the diamonds in the bit. The cutting action in a particular rock probably varies with bit pressure and speed. If the bit were slowly lifted off the rock, the effect of decreasing pressure might obliterate those bottom hole characteristics that are specific at the test pressure. Likewise, if the drill were stopped with the bit still in contact with the bottom of the hole, then decreasing speed effects would tend to obliterate the characteristics at the set test conditions. Therefore, in order to preserve those cutting effects impressed on the rock at test conditions, it seemed necessary to lift the bit off the bottom of the hole almost instantaneously once drilling conditions, i.e., revolutions per minute, pressure, and water flow became constant. In addition to observing the cuttings, the bit, and the bottom of hole, it seemed desirable to collect some quantitative data for purposes of correlation with the observations and for a record of bit performance. Consequently such data as revolutions per minute, force applied, and rate of advance of the bit were recorded. Six rock types, listed in Table I, were chosen for the tests. It was felt that these rocks had most of the variable characteristics of texture, bonding, and mineral hardness met in the common rocks generally being drilled. The sandstone was so poorly cemented as to be friable, even though most of the cement was silica. The limestone, though well cemented, was quite porous. Originally it was planned to conduct the tesk work with a full-scale drill unit, using EX bits, 7/8-in. core, 11/4-in. OD. The drill worked well, but was too cumbersome for rapid, accurate drilling of many short holes (1 ½-in.) in varied rock types. A new

Jan 1, 1954

By F. B. Plummer

PETROLEUM ENGINEERING deals with the production, transportation, and refining of crude oil. Refining is chiefly the work of the chemical engineer; production, that of the petroleum engineer. Production engineering only is discussed in this paper. Petroleum production engineering is closest related to and, in fact, is a branch of mining engineering. Formerly, many petroleum engineers were trained as mining engineers or mining geologists. The profession is related also to mechanical and civil engineering to about the same extent that mining engineering is. Petroleum production draws upon the mechanical branch for drilling and pumping machinery and upon civil engineering for the construction of transportation lines, water supplies, and water-disposal plants. Fundamentally, petroleum production engineering deals with the removal of the oil from the reservoir rocks, just as mining is concerned with the removal of ore. The process of oil production demands a specialized knowledge just as distinct from mechanical and civil engineering as mining is distinct from operating a Diesel engine. Even though the chief tools of the petroleum engineer are the drill and the pump, these may be of little avail, and certainly not efficient, if their selection and use is not based on a knowledge of the physical chemistry of oil, the geology of the formations, the structure of the oil sand, the hydrodynamics of the reservoir, and the interrelation of all these many factors.

Jan 1, 1936

By C. S. Yust, C. S. Morgan

ThIS note reports the observation of masses of dislocation etch pits around the weld necks of small single-crystal particles of calcium fluoride sintered to a cleaved face of a larger CaFz crystal. Crystal particles in the -50 +I00 mesh size range were placed on freshly cleaved CaFz surfaces and heated at 1250°C for 30 min in a tantalum container in an argon atmosphere. The sintered specimens were then etched at room temperature for 40 to 50 min in a 2 pct sulfamic acid solution which is a selective etch for dislocations in caF2.' Figs. 1 through 3 show the masses of dislocation etch pits observed around weld necks after etching. In some cases, particles were gone after removal of the specimens from the furnace although weld necks were readily visible. In other instances, no etch pits formed around a weld neck. A possible cause of concentrations of dislocations on the crystal surface is mechanical deformation of the base crystal when particles are dropped on it. If such a deformation does occur, it would be much smaller than that caused by the light punching of a crystal with a sharp instrument which results in large concentrations of etch pits. However, crystals deformed by punching with the sharp instrument and annealed at the conditions of these experiments (1250°C for 30 min) before etching showed no concentrations of dislocation etch pits. It is obvious that dislocations from the much smaller deformations, possibly created when particles are placed on the surface, would also anneal out. Etching of large crystals which had particles placed on them in the usual manner but which were not heated showed no dislocation concentrations such as shown in Fig. 1. The magnitude of dislocation etch-pit concentrations did not vary with extensive variation of the cooling rate. The appearance of many of the etch-pit clusters is typical of a well-annealed condition, indicating that the dislocation concentrations formed before the specimen temperature was lowered. Therefore, it is evident that thermal stresses in the neck area did not create the deformation indicated by the presence of the dislocations. The possibility exists that the etch-pit concentrations at places where particles had been removed may be the result of deformation accompanying the fracture of the sintered bond. That this is not so was demonstrated by breaking off particles around which no etch pits occurred. Re-etching never resulted in the large concentrations observed at sintering sites. The stress available to effect material movement during sintering of two particles will depend on the geometry at the contact point but can easily exceed the macroscopic yield stress in CaFz systems. It appears that the plastic deformation observed results from sintering or simply from the weight of the small particles. It has been previously argued that plastic flow makes an important contribution to the initial densification of oxides having the fluorite crystal structure.2p3 If plastic deformation occurs, it would begin as soon as the temperature is sufficiently high

Jan 1, 1967

By Cyril Stanley Smith

The following table, which is composed of data given in the author's first paper on the thermal conductivity of copper alloys1, contains tile results which have been obtained by previous workers on the thermal conductivity of the copper-tin, the copper-phosphorus and the copper-tin-phosphorus alloys (the phosphor bronzes). a Dr. Ing. Diss., Aachen, 1909. Quoted by Schenk: Ann. der Phys. (1910) 32, 261. b Beibl. Ann. der Phys. (1906) 29, 178. c Jnl. Inst. Metals (1928) 39, 375. d Jnl. Inst. Metals (192.5) 34, 43. e Ges. Abhand. Kennt. Kohle (1919) 4, 400. Experimental Methods Since the method of obtaining measurements of the thermal conductivity was identical with that described in the author's previous paper

Jan 1, 1931

By F. G. BREYER

ZINC metallurgists continue to follow with keen interest reports of successful results from the continuous retort plants at Palmerton, Pa., and Meadowbrook. W. Va. The new process had already demonstrated its ability to reduce the lead content of the metal and to effect savings in labor and fuel. The past year has shown that the retorts themselves can he built to last long enough so that the retort cost per ton of metal is lower than in past practice with small horizontal re- torts. A number of the latest type of retorts are reported to have been in continuous operation for over 18 months without a failure and are said to be still in good condition. This seems a complete answer to the last question which remained before continuous zinc smelting could he pronounced commercially practicable.

Jan 1, 1932

By P. G. Shewmon

A novel technique for determining the surface energy (?) and its derivative with respect to orientation, (?') is described. Essentially it involves the 'floating" of a wedge on the substrate, said wedge being made of a material which is not wet or only slightly wet by the substrate, i. e., as a greased needle "floats" on water. A thermodynamic analysis of a system in which the wedge is supported entirely by surface energy is given. If the original suyface is not at a cusp orientation, the surface tension is directly measurable from the groove angle formed. If the original surface is at a cusp orientation, there may or may not be a groove depending on the relative value of ?' and the weight of the wedge. Experiments primarily on copper and silver showed that sapphire, quartz and refractory metal wedges were wet while graphite wedges were not. The technique was demonstrated to work using graphite wedges, but the results obtained were not as eccurate as those obtained by other workers using the wire-creep experiments. It is concluded that the technique might prove most useful with non-metals where ?' is large and filament creep experiments would be quite difficult. If an absolute value of the surface free energy (?) of a metal is to be determined, the most reliable methods used to date measure an average over the various orientations exposed on a polycrystalline sample. For example, ? for silver, gold, and copper have been measured by determining the force required to just keep a thin wire,' or foil,' specimen from contracting under the influence of ?. Herring 3 has predicted and experiment confirms, that the sensitivity of this method is inversely proportional to the grain size.' Thus it cannot be used to measure ? for a particular orientation by using a foil single crystal or a very coarse-grained specimen. An accurate value if ? for tungsten averaged over a range of orientations has been determined using a field emission technique. The same techniques cannot or have not been used to measure ? for non-metallic solids, and as a result the values available are much less accurate.4 This Paper resents a means of making an absolute determination of ? for a particular surface orientation on any solid, as long as the given surface orientation does not break up into other orientations during an anneal. Experimentally ? is found to vary with orientation and at a few low index orientations it is found to have a cusped minimum, i.e., the derivative of ? with respect to the orientation of the surface changes discontinuously at the low index orientation, see Fig. 1. The slope of a plot of ? vs orientation (herein designated ?') is called the torque on the surface, since it tends to rotate the exposed surface toward the low index orientation, or if the surface is at the cusp orientation it opposes any force tending to rotate the surface out of the low index orientation. The ratio ?'/? has been determined for a few metals, but in cases where this ratio is high there is presently no means of determining either ?'/? or the absolute value of ?' for the orientations present on an annealed surface. The technique discussed herein also provides a means of determining an absolute value of ?' for those orientations which deviate only infinitesimally from a cusp orientation. It should work best on surfaces where ?'/? is large; that is, for cases where no other technique is available for measuring ?'. Aside from trying to learn more about surfaces through measuring ? and ?', the primary reason for wanting values of ? or ?' is to study adsorption. From measurements of the variation of ? for a particular orientation with the concentration of an impurity, one can obtain the number of impurity atoms adsorbed per unit area (Ti) on that orientation using the Gibbs adsorption equation.' where µi is the chemical potential of the adsorbed impurity. Thus, if absolute values of ? could be obtained for the free surface of a given surface orientation as a function of µi, ri could be determined for the given orientation. Furthermore, by equilibrating a grain boundary with the given surface at various values of ki, one could also determine ri for the grain boundary. Similarly Robertson 6 has pointed out that if y is taken to be a continuous function of and µi, then a2 ?/a @a µ2 = a2 ?/a pi a +. Thus, at all orientations away from cusps the following equation holds From a measurement of ?' vs ki, it is thus possible

Jan 1, 1963

By J. D. A. Morrow

TO my mind the National Bituminous Coal Act so far has proved one of the unhappiest experiences that has ever befallen the bituminous coal operators of the United States. Viewed in the light of its ugly consequences everyone should recognize this measure for what it is -a weird thing as unreal as a page from "Alice in Wonderland." Indeed it might be another stanza to the tale of the Walrus and the Carpenter, with the coal operators in the role of the unfortunate oysters who were taken on that memorable ramble. It is time that coal producers open their eyes, jerk themselves out of any lingering hypnotic optimism about the price-fixing provisions of this law, demand the repeal of these corroding clauses, and then set about remedying as best they can the disastrous effects of this retromingent scheme to regulate the coal business.

Jan 1, 1939

[*DAVID THOMAB ...................... 1871 *R. W. RAYMOND .1872-1874 *A. L. HOLLEY ....................... 1876 *Asurn 8. H~WITT ................... 1876 *T.ST~RYHUNT ..................... 1877 *ECKLBY B. COXB .1878-1879 *WILLIAM P. BHINN .................. 1880]

Jan 1, 1946

By T. M. Morris

R. T. Hukki (Finland Institute of Technology, Helsinki, Finland)—Two schools of thought are developing concerning the order of the rate of flotation. The paper by Morris is intended to show experimental evidence in favor of the first order rate. Arbiter, on the other hand, has presented an earlier paper" to demonstrate the validity of the second order rate equation. Unfortunately his method of plotting is open to criticism, as pointed out by Morris." A more sensitive method of plotting has been described by the writer,= whereby the data presented by Arbiter demonstrate the superiority of the second order plot. The general rate equation may be written in the following forms for the integrated first and second order equations: (A) t = -1/k In Co-R/Co (first order) [4] 1 (B) 1/t = - kCo + kCo2 1/R (second order) As a first approximation the value of Co may be taken as a unity, 100 pct or 1. Whether or not this is the case in all tests performed by Morris is impossible to judge, owing to the fact that the flotation times are extremely short, e.g. 150 sec in tests A. It would, indeed, be very interesting to know what the total recovery R would be after 1 hr of flotation, for example, instead of after 150 sec. Certainly there are circumstances when C, approaches unity within a very small margin of error. Morris has used the same approximation in his example D "since the feed to this cleaner

Jan 1, 1954

By E. R. Kaiser

COAL research during 1941 had a marked increase in activity on problems bearing directly on furthering the increased and improved use of coal in homes and industry. Coal producers and fuel engineers expressed a greater interest in its practical possibilities and the coal laboratories have shown an increased interest in applied research, of value at once or in the near future to industry and the public. A large volume of accomplishment in mining, coal analysis, and the fundamentals of coal constitution and coal chemistry also continued to fill the storehouse from which applied research and fuel engineering of the future can draw valuable data.

Jan 1, 1942

By M. H. HARRINOTON

THE Transactions of the Institute afford abundant evidence of the general recognition by mining engineers of the importance of a safety-lamp which will not only give warning of the presence of fire-damp, but will also indicate the proportion in which it is present.' Mining-men are only too familiar with the frequent and sudden changes that constantly occur at the working-face of a gaseous mine. Nothing illustrates more forcibly the pregnant condition of the strata enfolding the seam and the seam itself, than the fact that a circulation of perhaps 150,000 cu. ft. of air may contain 2 or even 3 per cent. of marsh-gas, representing a volume of from 3,000 to 4,000 cu. ft. of this gas pouring-out each minute from the natural strata into the mine-workings. It would, indeed, be strange if this great outflow of gas were always constant, and it creates no surprise that such earth-breathings, as they may be called, are spasmodic and irregular in their wane and flow. There are other causes that act to vary the gaseous condition of mine-air. Gas has a tendency, often very manifest in mine-workings and airways, to stratify and, at times, to travel long distances in veins or streams. It is common to catch and lose the gas in the lamp when making a test. At times two lamps, held side by side in an air current, will indicate different gaseous conditions of the passing air. When testing for gas, the lamp may suddenly fill with flame, in a mine-chamber, where a moment before a careful test showed the presence of but 1 per cent. of gas. It is sometimes remarked that there is little need of detecting a smaller percentage of gas than is revealed by the common

Jan 1, 1906

By E. H. Wells, A. Andreas

Greater progress than in any previous year was accomplished by the oil industry in New Mexico in 1936. The total number of completions in the state was 631, of which 549 were oil wells, 21 were hydrocarbon gas wells, three were carbon dioxide gas wells, and 58 were dry holes. The total oil production for the year was 26,804,446 bbl. Compared with the production for 1935 of 20,228,947 bbl., this represented a gain of 32.5 per cent. Of the total production, 25,337,382 bbl. came from Lea County. The average daily nonmarginal well allowable for that county was 115 bbl. the first of the year and 86 bbl. at the close. Production was regulated by the New Mexico Oil Conservation Commission,

Jan 1, 1937