Search Documents

By Orson Shepard

TEXTBOOKS on fire assaying list the following standard methods of assaying sulphide ores: (1) scorification, (2) litharge-niter, (3) soda-iron, (4) roasting, (5) combination wet and fire. The litharge-niter method has proved the most satisfactory, and is the usual method for assaying sulphide ores and concentrates. It gives good results when suitably conducted and when lead buttons of uniform size are produced so that the cupellation temperature can be properly controlled. The main objection to the method is the inconvenience of determining the amount of niter to add to each assay charge to produce lead buttons of suitable size from a set of fusions. For the assay of different materials, the niter requirement varies with the particular sulphide minerals present, the amount of sulphide minerals present, the slag composition, and the rate of heating the charge in the furnace. Except for some materials, so uniform in composition that the same amount of niter can be used in assaying all samples, the amount of niter must be determined for each sample to be assayed. This is done by either: (1) calculation from an estimate of the kind and amount of sul-phide minerals present in the sample, or (2) a preliminary fusion. Some assayers use one method and some the other. The estimation method takes the least time; but much experience is required to obtain close estimates on a wide variety of materials. At best, the sizes of the lead buttons obtained vary considerably. The preliminary fusion method usually gives lead buttons of fairly uniform size, although sometimes there is a variation because the oxidizing power of niter varies a little with the charge. This variation can be eliminated by two preliminary fusions: one to determine the reducing power of the ore, and the other to determine the oxidizing power of niter in the charge. The objection to the prelimi-nary fusion is the extra time and expense involved.

Jan 1, 1939

By R. E. Reed-Hill, J. L. Martin

Kinking is an important deformation phenomenon in poly crystalline a zirconium. The crjlstallo-gvaphic features of the most important form of kinking have been determined with the aid of twins formed at 77°K in grains previously kinked at high temperatures. It has been .found that the kink-band boundaries correspond to walls of edge dislocations with (1150) Burgers vectors and dislocation lines parallel to (1070). The present observations imply that basal slip is an important secondary-slip mode in polycrystalline zirconium. Previous single-crystal studies13 did not veveal this mode Other evidelzc.e for (0002)(1120) slip is also presented. ThE first studies of kinking in hexagonal metals were made by orowan,1 using single-crystal cadmium wires. He suggested that this was a new de- formation mode in metals, different from ordinary glide or twinning. Next, Hess and Barrett2 studied zinc-crystal rods in compression, and were able to offer an explanation of the phenomenon described by Orowan. They concluded that kinks required no new deformation mechanism and were a special form of deformation band that developed gradually and solely from basal glide. Similar kink bands were then observed by Washburn and parker3 on zinc crystals deformed in tension at low stresses and high temperatures. In titaniun,4 kink bands associated with {1010}<1120> prism slip have been observed in coarse-grained specimens. Magnesium5 and rhenium6 have also been observed to kink in conjunction with their basal- and {1010} prism-slip systems, respectively. Yttrium has (1010) as a predominant slip plane, but no observations of kink bands were reported.7 Since no previous investigations of kink bands in zirconium have apparently been made, this study was proposed. Its aim was to determine the crys-tallographic features of a type of kink band frequently observed in polycrystalline zirconium. EXPERIMENTAL APPARATUS All tests were performed on a type TTC Instron machine. The cross-head speed usually chosen in tension or compression was 0.02 in. per min. Ten-

Jan 1, 1964

By David J. Dunn

GENERAL NOTES Liner Design for Comminution Liners in crushers and mills are the mechanical link between machine and ore. The way liners transfer energy to media and ore determines to large degree the production rate, liner wear rate, maintenance cost, energy use, and availability of the comminution process. Plant capacity and mineral recovery economics, and return on investment, are thus strongly dependent upon these simple, low cost metal shapes of which so much is demanded. The complexity of dynamic relationships between liner configuration, material properties, ore characteristics, and operating parameters defy simplistic generalization. Rules-of-thumb and axioms of years past fall into disuse almost daily as new analytical methods, assisted by computers and sophisticated control systems, are applied to crushing and grinding processes. Recent literature is well supplied with references citing production benefits that improved liner designs produce. This chapter is intended to review especially promising liner designs and material developments and presents cameo case studies showing the benefits derived from their application to comminution circuits (Tables 1,2,4,5,7). Complete discussions of liner design and wear materials are beyond the scope of this chapter. Norman&apos;s comprehensive studies in references (1) and (2) and Mclvor&apos;s analyses of mill speed/configuration effects (3) are especially useful reading for designers and operators of crushing and grinding circuits. Changing trends in ore, product value, and costs of wear materials, interest, labor, and energy, make ongoing evolution of liner design equally important for existing mines and for projects still on the drafter&apos;s board. Original designs supplied as new equipment must, of necessity, be best estimates. These can usually be improved as operating experience replaces engineering forecasts. Advent of new materials or design concepts such as the Angular Spiral Liners (Korpi (4) ) or Norman&apos;s Bimetallic design (2) offer improvement potential that must be evaluated if a given circuit is to be kept competitive versus others making similar products.

Jan 1, 1982

By K. E. Brown, F. W. Jessen

It is deemed feasible to store atomic reactor fuel wastes in salt dome cavities when the differential pressure acting on the cavity does not exceed 3,000 psi and the temperature is less than 400°F. Tests at pressure increments of 1,000 psi were conducted on a 2-in, cylindrical cavity contained in a 6-in. long X 6-in. diameter salt core. The cavity exhibited stability under pressures up to 3,000 psi and temperatures to 300°F. At temperature ranges of 100 to 400°F and with pressures of 5,000 psi and above continuous deformation of the cavity resulted. Initial movement of the salt was observed at all pressares. This was evidenced by vertical deformation and cavity size reduction. INTRODUCTION The development of storage techniques for safe disposal of atomic reactor fuel wastes is a goal of the Atomic Energy Commission. Salt domes have been used successfully for storage of liquefied petroleum gases and hence should prove to be suitable for liquid waste products of atomic reactors. The purpose of the following work is to evaluate the practicability of utilizing salt dome cavities for such wastes and to de-termine particularly the effect of pressure and temperature on a salt cavity. This work represents a part of a comprehensive study covering the over-all problem of storing re- actor fuel wastes in salt domes and/ or salt beds. The problem of accurately determining the stresses which exist in rocks in the earth&apos;s crust is indeed a complex one. Theoretical studies have differed widely in many of the basic assumptions about the physical properties of the rock itself. Some solutions of problems in underground stress analysis assume that rock is elastic, homogeneous and isotropic in character; others assume that rock possesses plastic, viscous, elasticovis-cous properties, or a combination thereof. Experimental evidence has shown that salt possesses plastic, viscous and elasticoviscous properties.&apos; Recent work has shown that salt becomes more plastic with temperature.&apos; APPARATUS AND PROCEDURE For experimental study a cylindrical cavity was chosen for analysis since it provided maximum volume per unit of depth with constant diameter. This particular cavity shape, allowing for irregularities, can be easily leached out of salt domes in field operations. For the purpose of approaching underground storage conditions as nearly as possible, the following factors were considered: (1) control of pressure and temperatures, (2) measurements of temperature gradients throughout salt mass, and (3) measurement of structural stability of salt cavities. In order to obtain triaxial pressure on the salt cavity without resorting to the application of fluid pressure directly on the salt mass, a system was designed whereby the same effect could be produced through axial loading only. By cutting a core to close dimensions to fit a steel test cylinder and applying axial pressure, a lateral pressure was obtained. This equipment is shown in Figs 1 and 2. A steel cylinder was made from

By William F. Brace, Howard R. Pratt, Wayne S. Brown

In many engineering structures, the mechanical properties of large volumes of rock must be considered. Typically, such properties are assumed to be the same as those of small laboratory samples, although it is clear that the laboratory samples do not contain the joints, faults, and other natural planes of weakness of the rock mass. A cheap, convenient testing procedure is needed with which the engineer can more accurately assess the strength and elastic properties of natural jointed rock. As a first step in this direction, a test has been developed capable of determining mechanical properties of large samples in their natural undisturbed state. In the present paper, some preliminary experiments on relatively unjointed material are described. Numerous attempts have been made to measure the deformation modulus of rock masses with varying degrees of success. Rocha (1), Grimm (2), and Alexander (3) have placed flat jacks in a slot in the rock and measured the pressure required to deform the slot. Bonnechere (4) has grouted large flat jacks in granite masses and performed similar experiments using a variety of strain measuring techniques. The U. S. Bureau of Mines has conducted radial jacking tests in which a uniform radial stress is applied to the inside of a tunnel of circular cross section and radial deformation is measured by extensometers located at various depths in the tunnel fall. Plate jack tests (Rocha (5), Shannon and Wilson (6)), pressure chamber tests, and cable jacking tests (Zienkiewicz and Stagg (7)) have all been used to determine in-situ deformation modulus. Several bore hole techniques have also been used to measure rock deformation. These include bore hole jacks (Goodman (8)), bore hole dilatometers using expandable membranes (Menard (9)) and bore hole penetrometers. Most of the above tests except the radial jacking test have an unknown stress distribution and require considerable approximation to calculate a deformation modulus. These approximations include the use of elastic theory for solutions of rigid plates, thick-walled cylinders, etc., and determination of values for Poissons

Jan 1, 1971

By Robert Mehl

RELATIVELY few data have been collected on the rates of diffusion in ternary solid solution systems. In general it does not seem worth while to gather extensive data for such systems until the factors that determine the rates of diffusion in binary systems are better understood. But the rates of diffusion in a ternary system of limited solid solubility, in which the terminal solid solution is in equilibrium with an intermediate phase and may thus be represented as a quasibinary system, represents a case of special interest. In this case, where by reason of the association of the two solute metals in an intermediate phase a special attraction of the two solute atoms may be safely assumed, some interaction of these atoms during simultaneous diffusion in the solvent lattice might be expected. It has frequently been proposed that molecular solid solutions exist in quasibinary and in other ternary (and binary) solid solutions. There is no direct evidence for such solid solutions; arguments based upon the supposed anomaly in certain physical properties1 are hardly important; unexpected density relationships have proved deceptive ;2 suggestions of molecular solid solutions have been made on the basis of solution laws in their application to certain systems, but without result;3 attempts to find lattice parameters in the solid solution Al-MgZn2, which cannot be calculated from the separate effects of magnesium and zinc and might therefore be taken as evidence for a molecular aggregation, have given negative results.4 Fundamentally, methods for the determination of the state of molecu¬lar aggregation in solution depend upon the kinetic behavior of the par-ticles constituting the system. If it could be shown that the two solutes in a quasibinary ternary system diffuse in molecular proportions, despite a radical difference in the separate rates of diffusion of each solute when diffusing alone in the solvent lattice, some basis for the concept of molecu-lar solid solution would be afforded. Freche5 examined the rates of independent and simultaneous diffusion of magnesium and silicon in

Jan 1, 1939

By James D. Sisler

Among the various studies made by the Coal Fact Finding Commission, appointed by President Warren G. Harding in 1922 to investigate all phases of the coal-mining industry in the United States and to report to Congress, was one concerning the amount and nature of losses in mining bituminous coal in the eastern part of the United States. This study was carried on under the direction of the U. S. Bureau of Mines. The writer was appointed field engineer to investigate the problem in Ohio, Pennsylvania and West Virginia. Some 400 mines were studied in these three states and conclusions were drawn from many sources of data. The summary report written by George S. Rice and J. W. Paul states that "the field reports indicate that the recovery in Ohio will remain about as at present, except in the Belmont district; whereas in Pennsylvania it will gradually improve, and in West Virginia it will improve rapidly." Since 1922, the writer has been interested in gathering material to substantiate or contradict these prophecies. Nature of Coal Losses There are six general causes of losses of coal in mining: (1) coal left on the roof and bottom; (2) coal lost in room, entry and panel pillars; (3) coal lost in oil-well or gas-well pillars; (4) coal lost under buildings, railroads and boundaries; (5) coal lost in handling and prepayation, underground and surface; (6) coal lost by rolls, thin or dirty areas and under streams. Local economic aspects that dominate the type of mining conditions determine to some extent whether certain losses are avoidable or unavoidable. In general, however, unavoidable losses include coal lost in the protection of buildings, streams, railroads, restricted properties and around oil and gas wells. Barrier pillars and other safety pillars are unavoidable losses as long as their size does not exceed the minimum for adequate safety. Natural physical conditions beyond human control, such as rock faults, clay veins, partings and binders, bad top and bottom, rolls and horsebacks, cause unavoidable losses. Unavoidable losses

Jan 1, 1931

By Douglas Bunting

IN THE anthracite fields of Pennsylvania, mine fires occur with more or less regularity and their existence is an ever-present hazard in coal mining. In all probability 90 per cent. of the mine fires can be ascribed directly or indirectly to the ordinary miner&apos;s open lamp. Other causes may be smoking, electrical installations, gas explosions, gas feeders, and the communication of fire to the outcrops from ash dumps, culm banks, timber and brush fires. Fires in pump rooms, engine rooms, and barns have been largely eliminated as a result of the Act of .Assembly, approved June 15, 1911, which provides that all inside buildings, including engine rooms, pump rooms, barns etc. shall be constructed of incombustible materials. Smoking of pipes, cigars, and cigarettes should be prohibited in the mines and too much care cannot be exercised in preventing fires by enforcing all rules designed for that purpose. Mine fires that involve underground fighting are invariably dangerous, and all fires, irrespective of the method pursued in extinguishing them, involve property loss and expense. Each fire generally presents a more or less original problem, dependent on the particular conditions. Generally mine fires may be divided into two classes: Those occurring in inaccessible workings and those occurring in accessible workings. The methods pursued in extinguishing or controlling mine fires are as follows: (1) direct attack, (2) smothering by sealing, (3) flushing with silt or other solids, (4) flooding with water, (5) cutting off, (6) surrounding with incombustible materials, (7) digging out by stripping from the surface. Most fires are extinguished in their incipiency by direct attack and failure to extinguish by this method is due to late discovery, lack of water, and facilities for fighting, or improper procedure in the initial attack. Should the method first pursued be unsuccessful, careful consideration should be given in determining next the method to be adopted; then the work should be carried on as rapidly as possible and under the supervision f the most competent persons. Materials and supplies should be fur-

Jan 9, 1921

By T. T. Quirke, L. C. McCabe

The object of the present investigation was to discover a physical basis for rank differentiation of coals, particularly the coals of the Illinois basin. Vitrainl was selected as the most appropriate coal material to use in the investigation, because of its homogeneity and ease of acquisition and handling. Previous Investigations.—Hoffman and Jenker2 have shown that their index of reflection is a characteristic of coal rank and that the Leitz slit microphotometer may be used in determining the different intensities of reflection. Zhemchuzhnikov3 measured the luster of several Russian coals with a color analyzer and found that the degree of luster was indicative of rank. Luster-volatile matter curves based on data from Sucan and Donetz coals were satisfactorily used for determining the rank or volatile content of other coals after the luster strength was determined. In 1934 Fisher4 reported refractive indices of 1.76 for bituminous vitrain and 1.87 for semibituminous vitrain. Investigation of Angle of Polarization.—Early in the present investigation several determinations of the refractive indices of the vitrains were made by immersing the minus 150 plus 200-mesh powder in oils. It was found that all the samples fell within the range 1.6 to 1.8. However, difficulty was encountered in securing oils in this high index range that were closely enough spaced to separate some of the coals. The writers made a number of determinations of the angle of maximum polarization from the polished surfaces of the vitrains and derived their refractive indices by the procedure described in the following paragraphs. Johannsen5 states the fundamental concepts underlying this procedure as follows: In general, in an isotropic medium light vibrates in all directions at right angles to the direction of propagation, and when it meets with another isotropic medium at an angle, part of the light is reflected and part refracted. It has been found that after reflection or refraction, the vibrations do not move with the same freedom in every

Jan 1, 1938

By T. T. Quirke, L. C. McCabe

The object of the present investigation was to discover a physical basis for rank differentiation of coals, particularly the coals of the Illinois basin. Vitrainl was selected as the most appropriate coal material to use in the investigation, because of its homogeneity and ease of acquisition and handling. Previous Investigations.—Hoffman and Jenker2 have shown that their index of reflection is a characteristic of coal rank and that the Leitz slit microphotometer may be used in determining the different intensities of reflection. Zhemchuzhnikov3 measured the luster of several Russian coals with a color analyzer and found that the degree of luster was indicative of rank. Luster-volatile matter curves based on data from Sucan and Donetz coals were satisfactorily used for determining the rank or volatile content of other coals after the luster strength was determined. In 1934 Fisher4 reported refractive indices of 1.76 for bituminous vitrain and 1.87 for semibituminous vitrain. Investigation of Angle of Polarization.—Early in the present investigation several determinations of the refractive indices of the vitrains were made by immersing the minus 150 plus 200-mesh powder in oils. It was found that all the samples fell within the range 1.6 to 1.8. However, difficulty was encountered in securing oils in this high index range that were closely enough spaced to separate some of the coals. The writers made a number of determinations of the angle of maximum polarization from the polished surfaces of the vitrains and derived their refractive indices by the procedure described in the following paragraphs. Johannsen5 states the fundamental concepts underlying this procedure as follows: In general, in an isotropic medium light vibrates in all directions at right angles to the direction of propagation, and when it meets with another isotropic medium at an angle, part of the light is reflected and part refracted. It has been found that after reflection or refraction, the vibrations do not move with the same freedom in every

Jan 1, 1938

By Torres S. Ricardo, Encina M. Víctor, Segura O. Claudio

INTRODUCTION This paper is a conceptual resume of engineering studies that have been evaluated by the Mine Department related to production planning over the next twenty-five years. These studies have been required principally because: a) The Rio Blanco Mine, property of CODELCO- CHILE, Andina Division, faces an operational problem due to heavy snowfall in winter which enters the surface subsidence area of the cave; later melts and filters into the broken ore creating a product that is difficult to transfer through the orepasses. The phenomenon is especially serious during the spring and has been increasing over the years. This element that complicates extraction will be controlled with the procedures proposed or others that may be determined in the future. b) The mine will increase production in 1985 by 40% . LOCATION The deposit is located in the central region of the Andes Cordillera, at an altitude of approximately 3,600 m above sea level, 50 km to the northeast of Santiago. The main camp is Saladillo (at 1,300 meters above sea level) located 30 km from the mine. Due to its location, the mine is subject to heavy snow storms during the year. On many occasions the road from Saladillo to the mine is closed because of storms and avalanches. For this reason the company has self-sufficient civil facilities near the mine to cover the needs and welfare of the working force. These housing facilities are connected to the mine by underground passages. For the same weather related reason the primary and secondary crushers, and the entire concentrator complex are located underground. GEOLOGIC CHARACTERISTICS Geology Based on the geologic model developed for the Rio Blanco deposit and comparing it with standard models pertaining to copper porphyries, it can be concluded that this deposit is part of the apical sector of a mega deposit and therefore the projections of the Xio Blanco cop per mine are very favorable, both in lateral area and depth. In order to confirm and evaluate these geo- logic features, an extensive drilling program was started at the Rio Blanco deposit. Diamond drill holes were drilled to depth as well as in the areas named "La Americana", "Don Luis" and "Elguin". The area explored by the drill program is 3 km long in a north-south direction and 1.5 km wide in an east-west direction. In some sections the drilling in depth reached the 2,300 m elevation mark. The lowermost level in the mine is at elevation 3,070 m. These new studies have permitted the recognition of the following lithologic units: Andesite Andesite Breccia Granodiorites, Rio Blanco and Cascada Granodiorite Breccia Quartzmonzonite Porphyry Monzodiorites and Latites Tourmaline Breccia Dacite Pipe and Rhyolite marginal ring. The mineralogical study permits the definition of three stages of hypogene and hydroterma1 alteration of importance with a time-altered sequence. These stages correspond to a late hydrothermal stage. The kinds of alteration that have been recognized are: Potasic Alteration Propylitic Alteration

Jan 1, 1981

By P. B. Scotland

THE mines of the Arizona Copper Co. are situated in the Morenci-Metcalf copper district in southeastern Arizona. This copper-bearing district covers a triangular mountainous area of about 3 square miles, rising abruptly from the gravel plateau of the surrounding country. In this area, an immense intrusion of porphyry has displaced, shattered, and engulfed the shales, limestones, and quartzites formerly bedded on the basal granite. Outcrops of oxide ore were discovered in 1873, and these surface ores were found to connect in depth with large bodies of high-grade oxide ores in the limestones and shales. The smelting of these ores in blast furnaces continued until about 1893, when the rapid exhaustion of the high-grade ore led to the discovery and exploitation of the low-grade sulphide ores in the adjoining porphyry. Methods of concentration were then devised and the low-grade ores finally rendered profitable. The Arizona Copper Co. and the Detroit Copper Mining Co., operating in the same district, were the pioneers in the successful development of the low-grade "porphyry" properties of to-day. The largest mines of the Arizona Copper Co. are the Humboldt and Clay at Morenci, and the Coronado, Metcalf, and King at Metcalf. These mines produce about 4,000 tons daily of concentrating ore containing from 2.5 to 2.8 per cent. copper. The topography of the country is very rugged and mining operations are conducted principally through adit levels. A few of the mines are opened by shafts, the deepest being 1,100 ft., in the Coronado mine. ORE OCCURRENCE The low-grade sulphide ore occurs as: (1) disseminated deposits in the main stock of quartz porphyry; (2) lode deposits in fault fissures in granite. The high-grade oxide ores were found as tabular deposits in limestone and shale close to contacts with porphyry. Low-grade oxide ore formed the outcrop of some-&apos; the sulphide orebodies; the majority of the outcrops, however, were barren.

Jan 2, 1915

Arizona ROBERT E TALLY, Chairman CARL F MILLS, Secretary-treasurer, P O Box 1462, Jerome, Ariz W. S. BOYD THOMAS H O. O&apos;BRIEN F. W MACLENNAN Boston Meets first Monday each winter month GALEN H. CLEVENCER, Chairman HOLCOMB J BROWN, Vice-chairman F LEROY FOSTER, Secretary-treasurer, Room 8-219, Mass. Inst of Tech, Cambridge, Mass A. E WELLS H A WENTWORTH

Jan 1, 1923

By Edgar Newhouse

THE lead smeltery at East Helena, Mont., controlled by the American Smelting & Refining Co. since 1899, has been in continuous operation for the past 25 years. Most of the old smelting and roasting practices have been superseded by newer and more modern methods, but on account of the difficulties involved in changing the original construction, some of the methods in use of handling materials are not the most modern. This plant, however, is particularly interesting as being one of the few essentially lead smelteries in the United States. At Federal, Ill., Collinsville, Herculaneum, and possibly other places, similar work is being done, but it is doubtful whether any of them produces as&apos; much lead as the East Helena plant, whose monthly production averages 6,500 tons. The situation, 5 miles east of Helena, is convenient to both the Great Northern and Northern Pacific railroads, while the electric power is obtained from Canyon Ferry, 12 miles east on the Missouri river. Local quarries supply the requisite amount of lime rock, Which the contracts require to be crushed to 5 in. Of the 450 men on the monthly pay roll, a census showed 200 Austrians, 110 Americans, and 30 Italians, the balance being made up of miscellaneous nationalities. The ore supply is mainly derived from the Coeur d&apos;Alêne mines in Idaho, and consists of crude ore, coarse and fine concentrates, middlings, and slimes. About one-half of the total output of the Coeur d&apos;Alêne camp is sent to East Helena. An average analysis of these ores gives approximately 40 per cent. lead and 11 per cent. sulphur. Local shipments, varying, from month to month, are mostly highly siliceous gold and silver ores carrying little lead. Small shippers, leasers of old mines, and prospectors are very numerous throughout Montana, and it is the policy of the company to encourage these men by every possible means, including the free sampling and analysis of their ores and aid in the development of their mines and prospects whenever their results show promise.

Jan 8, 1914

By Bhudeo N. Sinha, Paul Dean Proctor

Heavy metal contents in stream waters, sediments, and selected aquatic algae were determined for the upper Meramec River basin, Missouri, of 3905 km2 (1508 sq mi) area and site of the proposed and controversial Meramec dam and reservoir. Six distinct drainage areas within the basin are: (1) a lightly industrialized and farm area, (2) a primitive forested- ranch area, (3) an area which includes the Northern New Lead Belt, (4) the westward drainage of an old and extensive barite mining area, (5) the main trunk of the Meramec River, and (6) short north-divide tributaries of the Meramec River. Lower Paleozoic sediments rest nonconformably upon eroded and hilly Precambrian igneous basement. This locally rises as major inliers and also makes up the St. Francois Mountains to the east. Major lead, and lesser zinc, copper, cobalt, and nickel mineralization occurs in the buried Cambrian Bonneterre dolomite. Residual barite is present along the eastern fringe of the basin and is derived from the Potosi formation. Some 62 water samples, active stream sediments (AS), bank samples (BS), and 11 selected aquatic algae samples were collected in the various drainage areas and analyzed for copper, lead, zinc, cadmium, nickel, arsenic, and mercury contents. Heavy metals in water have a maximum range of 1-120 ppb (parts per billion), and this for zinc. The AS and BS sediments have orders of magnitude greater acid leachable metal contents in the -80 mesh fraction, with lead hawing the greatest range of 11-1028 ppm. Heavy metal content of stream-algae approaches that of the sediments in which they grow. Most anomalous heavy metal accumulations occur near mining and milling activities and in the streams draining such areas. Significant distortions of the primary dispersion pattern militate against geochemical exploration for hidden ore zones, but do demonstrate the mining, milling, and smelting activities of man, and sporadic mineral occurrences in younger horizons.

Jan 1, 1980

By V. F. Parry, S. P. Burke

The presence of gas in coal mines necessitates the use of costly ventilation arrangements and the use of expensive mining methods. On the other hand, the gas itself in many instances is of considerable intrinsic value, and its separate recovery might conceivably be a profitable undertaking. This paper is concerned with a study of the movement of gas in coal strata with the object of determining the laws governing gas movement and thus making at least a preliminary step toward the solution of the more practical problem of its control or recovery. Naturally, so important a subject has received much attention from scientists and engineers. In most cases, however, the studies have been concerned with the origin1$, the amount" the composition3 and the method of retention4 of the gas in coal; or, from the more practical side, have been concerned with the phenonlena and conditions associated with outbursts5 or explosions and their control. Numerous studies also have been made of the permeability of coal to gas" of gas pressures measured in coal seams, etc. The authors are unaware, however, of any attempt to present a consistent or complete picture of the laws governing the movement of gas through the coal. Study in West Virginia A recent study conducted at this University7 gives the first presentation of the distribution of pressures in a small section of a coal seam. Holes were drilled into the coal rib to various depths and at various distances from the coal face. The location selected for study was as remote as possible from disturbing influences of mining operations, faults, "wants," etc. The pipes extending into the coal that were used to determine pressures were grouted into the borehole for the entire depth of the hole, and great precaution was taken to insure accurate pressure readings. A map of the geology of the region, a map of the probable boundary and extent of the coal seam, a current map of the mine and a

Jan 1, 1936

By V. F. Parry, S. P. Burke

The presence of gas in coal mines necessitates the use of costly ventilation arrangements and the use of expensive mining methods. On the other hand, the gas itself in many instances is of considerable intrinsic value, and its separate recovery might conceivably be a profitable undertaking. This paper is concerned with a study of the movement of gas in coal strata with the object of determining the laws governing gas movement and thus making at least a preliminary step toward the solution of the more practical problem of its control or recovery. Naturally, so important a subject has received much attention from scientists and engineers. In most cases, however, the studies have been concerned with the origin1$, the amount" the composition3 and the method of retention4 of the gas in coal; or, from the more practical side, have been concerned with the phenonlena and conditions associated with outbursts5 or explosions and their control. Numerous studies also have been made of the permeability of coal to gas" of gas pressures measured in coal seams, etc. The authors are unaware, however, of any attempt to present a consistent or complete picture of the laws governing the movement of gas through the coal. Study in West Virginia A recent study conducted at this University7 gives the first presentation of the distribution of pressures in a small section of a coal seam. Holes were drilled into the coal rib to various depths and at various distances from the coal face. The location selected for study was as remote as possible from disturbing influences of mining operations, faults, "wants," etc. The pipes extending into the coal that were used to determine pressures were grouted into the borehole for the entire depth of the hole, and great precaution was taken to insure accurate pressure readings. A map of the geology of the region, a map of the probable boundary and extent of the coal seam, a current map of the mine and a

Jan 1, 1936

By J. S. Levine

A series of four displacement experiments has been run in a large alundum core. Flow potential distribution in each liquid phase was measured continuously through oil-wet and water-wet capillary barriers, using a null-point pressure balance, and saturated distribution was determined from electrical resistivity measurements. A method has been devised for calculating the effective (and relative) permeability to each phase at any time and at any point in the flow system for the transient displacement process. Relative permeability points have been calculated and average curves drawn for oil displacing water and water displacing oil. The values of dynamic capillary pressure have also been determined. Data have been substituted into the generalized Buckley-Leverett fractional flow equation and a comparison between actual and theoretical breakthrough recoveries is shown. Displacement experiments have been performed in the laboratory for many years in an effort to determine the effect of a number of parameters on multiphase flow in porous materials. In the literature of petroleum technology, Wyckoff and Botset&apos; were among the first to develop the relative permeability concept and to show experimentally that oil, gas, and water can flow simultaneously through a porous medium in a precise way governed by certain fluid properties, by the relative saturation of each fluid, and by characteristics of the medium itself. Somewhat later, Leverett2 and Hassler, Brunner, and Deahl11 developed some theoretical concepts of capillary behavior in porous materials. The work of Buckley and Leverett3 presented a theoretical analysis of immiscible liquid displacement based on the equation of continuity and the Darcy equation for viscous flow of each fluid. Subsequent investigators attempting to verify the Buckley-Leverett equation have, in general, deliberately neglected the capillary pressure term or have performed experiments in such a manner that it could be neglected. Terwilliger, et al4 in 1951, obtained agreement between theory and experiment for the constant rate displacement of water by gas in a long vertical sand column. Rapoport and Leas5 have investigated the

Jan 1, 1955

By Hugo L. Johnson, Robert Wallace

THE Midvale plant of the United States Smelting Refining and Mining Company consists of a flotation mill for concentrating sulphide ores of lead and zinc by differential flotation to produce three separate concentrates, one of lead, one of zinc, and one of iron pyrite; and a lead smelter for smelting ores and concentrates to produce base lead bullion, The plant, including its shops, laboratories, office, railroad yards which serve both mill and smelter, and areas reserved for tailing ponds and slag dumps, covers 646 acres on the right bank of the Jordan River at Midvale, Utah. It is twelve miles south of Salt Lake City and sixteen miles east of the West Mountain mining district at Bingham Canyon from which is drawn a large part of its ore supply. Custom ores are treated as well as the product of Company mines.

Jan 1, 1948

By Mark A. Ammon

The two most widely used methods of measuring hardness are the Brinell and the scleroscope. In the Brinell method a hardened steel ball is pressed into the steel under a definite load and the area of the resulting depression is measured. The load in kg. per sq. mm. of the area of the depression is taken as a measure of the hardness. Within certain limits the hardness number so determined is independent of the load or the size of the ball. In the scleroscope method a small weight carrying a diamond point is dropped through a glass tube upon the steel and the amount of rebound is taken as proportional to the hard-&apos; ness. In both methods the scale of hardness is an arbitrary one; however, they agree in a comparative may, that is, a steel showing 50 per cent. increase in hardness by the Brinell test mill show approximately 50 per cent. increase in hardness by the scleroscope test. Yet upon consideration of the two methods it appears that, upon a steel which has been carbonized, this should not be the case ; for the scleroscope method gives almost exclusively the surface-hardness, and the condition of the material below the surface has but a slight bearing upon the hardness number. The results given by the Brinell method should, however, be the exact opposite; for the depth of penetration &apos;of a ball pressed into the steel would be dependent to a large extent upon the condition of the material below the surface. This is particularly obvious when it is considered that the size of the ball ordinarily used in the Brinell method is 1 cm. (about 8 in.) in diameter under a load of 3,000 kg., while the diamond point of the scleroscope is in the neighborhood of 0.01 in. across, fitted in a hammer of about 0.5 oz. weight and dropping from a height of 10 inches.

Jan 1, 1913