Search Documents

By George J. Young

DURing the spring of 1910 1 visited a number of open-pit brown-coal mines and underground workings in the vicinity of Halle, Halberstadt, Leipsic, Cologne and Bonn. The notes which I took and the observations which I made at the time have been condensed and make up the principal part of this paper. Certain supplementary information has been taken from several sources which are given in the paper. The mining of brown coal is one of the important industries of Germany. The coal varies in color from dark brown to almost black and is soft like loam. Pieces of wood and strips of bark and even parts of tree trunks are frequently encountered in the excavation although the coal for the most part consists of a pulverulent, more or less matted mass of small particles of vegetal matter. It is a product between peat and lignitic coal. An analysis, taken from Coal Resources of the World shows the approximate composition of the material: Moisture, 53.73 per cent.; ash, 4.98; fixed carbon, 18.08; volatile carbon, 23.31 per cent. Thc principal characteristic is the amount of moisture. This seldom runs less than 48 per cent. The ash is usually low and ranges from 5 to 10 per cent. The sulphur content is usually less than 0.5 per cent. The heating effect of the fuel ranges from 2,000 to 2,500 calories. The commercial deposits are confined to the Tertiary period although

Jan 1, 1916

By O. Saeki

Dolomite-fluxed pellets have been produced at Kakogawa Works, Kobe Steel, Ltd., since August, 1975. The pellets contain 5.5 % dolomite and have a basicity (CaO/Si02) of 1.3. By charging 30-50 % of dolomite-fluxed pellets into the two large blast furnaces at Kakogawa, a low fuel rate of 450 kg per ton of pellets has been achieved with better furnace permeability and gas utilization. Laboratory studies show that dolomite-fluxed pellets have excellent high temperature properties, and that their softening and melting-down temperatures are about 50°C higher than those of lime-fluxed pellets, and that reducibility at 1250°C is increased from 25 to 70 %.

Jan 1, 1977

By M. Felsenthal

Engineers are frequently faced with the problem of having to predict oil recovery from a solution gas drive reservoir in the early life of a field. This is often the time when actual laboratory or field-derived gas-oil permeability (kg/k0) data are not yet available. Although excellent collections of k0/k0 data for various types of rocks may be found in the literature,1,2,3 a need exists for a more detailed correlation of k0/k0 data with core properties such as porosity, permeability, clay content or pore-size distribution. It is the purpose of this article to present this type of correlation for sandstone material. The correlation is based on laboratory tests performed on over 300 core samples from 19 reservoirs in the United States and Canada. EXPERIMENTAL Cores were analyzed by routine procedures, using samples of conventional size (7/8-in. diameter, 7/8-in long) cut parallel to the bedding planes. Air permeability was measured at 1.67 atm mean pressure in a Hassler-type apparatus. Porosity was determined with the aid of a Ruska bulk volume meter and a Boyle's Law rock volume meter, An evaporation method' was used to evaluate irreducible water saturations. Core samples were saturated with 25,000 ppm NaCl brine. The brine was reduced to the irreducible saturation, and the remainder of the pore space was filled with kerosene. This was followed by multiphase flow tests using the so-called "dispersed feed" technique.5 n this technique, gas and oil (kerosene and kerosene-saturated air) were dispersed with the aid of a porous Alun-durn feed head, the face of which contained a waffle-shaped system of Lucite-lined grooves. Oil entered the back side of the feed head and emerged at the raised areas of the front face. Gas was introduced directly into the system of grooves at the front face. The gas-oil mixture then entered the test core which was kept in capillary contact with the feed head. Permeabilities were determined from rate and pressure measurements and saturations from weights. All determinations were performed at equilibrium or steady-state conditions. Pore-size distributions were determined on selected samples by a mercury injection technique.6 GENERAL CORRELATIVE TRENDS When examining data from a given reservoir, it was noted that k0/k0 vs saturation curves became generally less steep as specific air permeability increased, a development that has a favorable effect on oil displacement efficiency by solution gas drive. This trend has also been reported by others in the literature.' An effect of porosity on k0/k0 data was also noted. This effect was not generally discernible in a study of relative permeability data for a given reservoir but became apparent when data for sandstone reservoirs of similar lithology but differing average porosity were compared. For instance, in a comparison of argillaceous and/or calcareous sandstones from 11 reservoirs ranging in average porosities from 14 to 28 per cent, a definite trend was noted, indicating that for a given permeability k0/k0 curves became less favorable (i.e., steeper) as porosity increased. A similar trend was observed for a group of comparatively clean sandstones from five reservoirs ranging in average porosities from 15 to 21 per cent. For a given permeability and porosity, comparatively clean sandstones gave more favorable k0/k0 curves than argillaceous and/or calcareous sandstone or chert reservoirs. The laboratory studies also showed that least favorable k0/k0 curves were exhibited by shaly sandstone, conglomerate, and sandstone containing carbon inclusions. Table 1 lists the various source reservoirs classified by lithology types. To facilitate a correlation of k0/k0 data with core characteristcis, it was found expedient to work with

By M. J. Ginsberg, N. A. Gokcen

THE preliminary study of electrochemical desul-furization performed by Ohtani and Gokcen1 left a number of points concerning the process to be investigated. Two of these were i) the determination of the effect of greater current and voltage on the desulfurizing Flower of acid slags (% CaO/% SiO2- 1) and ii) the possibility of the loss of silica in slag by the reactions 2C (in metal) + SiO2 (slag) = Si (in metal) + 2CO(g) and C + SiO2 (in slag) = SiO(g) + cO(g) proceeding to a point at which the composition of the slag was sufficiently altered toward the basic side so a1.s to noticeably affect the rate of de-sulfurization. The apparatus and the procedure used in the present investigation were the same as those used by Ohtani and Gokcen, except the control circuit was connected to 120 v dc instead of 24 v dc and thereby allowed greater freedom in choosing the values of both current and voltage. The graphite crucible containing the melt and serving as the cathode was 3-in. high, and was of 1 1/2-in. ID with a graphite bar of 3/8-in. diam and 8-in. length threaded into the bottom for electrical connection. This was placed into a magnesja outer crucible with a hole in the bottom and alumina insulation was packed between the two crucibles. A charge consisting of 180 g of

Jan 1, 1962

By J. H. Brophy, J. Wulff, H. W. Hayden

The mickel-activated sintering of tungsten occurs in two stages of densification. A kinetic analysis of the second stage has been based on an appropriate model of the process. As in the first stage, the rate-controlling mechanism for the second stage is also the solution of tungsten in the nickel carrier phase. The transition from the relatively rapid first-stage results from the spherozdization of pores and the initiation of grain growth. Finer grain size due to higher-nickel content leads to more rapid and higher degrees of densification 1 HE sintering of tungsten is accelerated by small additions of nickel, cobalt, and iron.' Experimental evidence in detail has shown that nickel-coated, hydrogen-reduced tungsten powder may be sintered to more than 90 pet of theoretical density at l100o C.2, 3 Simultaneously, a kinetic analysis of the process showed that it took place in two distinct stages. In the first stage, nickel evidently served as a carrier phase through which tungsten atoms could move. This stage was kinetically similar to the "solution-precipitation" step postulated when the carrier phase is a liquid,4 although in the Ni-W case, there is no evidence of the existence of a liquid phase either in equilibrium phase relationships or in microstruc-tures at the temperatures under consideration. It has been shown that this stage corresponds to a process which is rate controlled by a phase boundary reaction.3 More recent evidence has been presented5 showing that after the initial rapid stage of sintering, densification continues in the final stage but at a slower rate, although no mechanism for this stage of densification was defined. An analysis of later stages of densification in solid state sintering has been presented,6 but it is not directly applicable in the present case of activated or carrier phase sintering. It is the purpose of this investigation to study the final stage of nickel activated tungsten sintering in greater detail The effect of varying nickel content has been examined, and a possible kinetic mechanism defined. EXPERIMENTAL PROCEDURE AND RESULTS Commercial hydrogen-reduced tungsten powder from Wah-Chmg Corp., having a nominal particle size of1 µ and a B.E.T. specific surface area of 5500 sq. cm per g was mixed with aqueous solutions of hydrated nickel nitrate in proportions sufficient to produce nominal compositions of 0.25, 1, 3, and 5 wt pet Ni. This solution was then evaporated to dry-ness at approximately 150" C for 15 hr. Following evaporation, the resulting powder cake was broken with a mortar and pestle and reduced in hydrogen at 800oC for 1 hr. Following reduction, the powder

Jan 1, 1962

By Edna A. Dancy, Gerhard J. Derge

Jan 1, 1963

Earnings of engineers in the period 1956 to 1958 continued the upward trend observed in the previous survey interval, 1953 to 1956. The overall median (all graduates) was $6500 in 1953, $7750 in 1956 (a 19 pct upstep or about 6.5 pct annually), and $8750 in 1958 (up 13 pct from 1956 or 6.5 pct average yearly). The latter represents an increase from mid-1956 to mid-1958. For this same two-year span the Consumer Price Index rose 1.5 pct and the Average Gross Weekly Earnings for Production (Manufacturing) climbed close to 10 pct. Median earnings for the major classifications studied are presented in Table I. The increase in engineering earnings are not distributed equally among the various activity classifications or among the experience levels of the survey. Summary results of the changes of the median lines for the major divisions are presented in Table 11. Data in this table are approximations- dollars are rounded to the nearest $50 unit and percentages to the nearest full percentage.

Jan 1, 1959

By Hermann Schmalzried, Carl Wagner

UPON heating a metal oxide or sulfide in H2, first only oxygen or sulfur is removed from the surface. Thus the metal/nonmetal ratio in the oxide or sulfide increases and the thermodynamic activity of the metal increases accordingly. For the formation of metallic nuclei, a certain super saturation is necessary, i.e., the activity of the metal must become greater than unity. Once nuclei of the metal have been formed, the supersaturation is supposed to decrease. Even under steady-state conditions of a reduction process, however, the activity of the metal inside an oxide or sulfide phase must be greater than unity in order to have a driving force for the individual steps of the reduction process. As an example, consider the reduction of Ag2S with a high mobility of cations and electrons. As shown schematically in Fig. 1, the reduction process involves the following steps:' 1) sulfur removal along the entire Ag2S surface in form of H2S, 2) migration of Ag' ions and electrons from the Ag2S surface to nuclei of metallic silver, 3) transfer of Ag+ ions and electrons from the Ag2S phase to the metal. For a finite rate of step 3, the activity of silver in Ag2S next to the Ag2S-Ag interface must be greater than unity. Moreover, for a finite rate of step 2, the activity of silver at the gas-Ag2S interface must be still somewhat greater. Theoretical considerations lead to the tentative conclusion that at least under steady-state conditions the supersaturation will be rather low.' To test this conclusion, the average activity aAg of silver in a Ag2S tablet about 2 mm thick with a diameter of 5 mm was followed as a function of time by measuring the electromotive force E of the cell Pt I Ag | Agl I Ag2S I Pt where AgI is used as a solid electrolyte in which only Ag+ ions are mobile. The activity aAg is calculated as aAg=exp(-EF/RT) Since the diffusion coefficient for transport of silver in Ag2S is very high (- 3 . l0-2 sq cm per sec),3 the average activity aAg is representative for both the bulk and the surface of the Ag2S tablet. Experiments were conducted at about 400°C. The cell was surrounded by an aluminum block in order to secure a uniform temperature and to eliminate thermoelectric effects. With the help of a potentiometer, first a potential of 0.16 v was applied to the above cell in argon in order to obtain a well defined initial state with a Ag/S ratio close to 2.000.~ Then the cell was disconnected from the potentiometer and a gentle stream of H2 was passed along the Ag2S surface. In view of the removal of sulfur in form of H2S, the electromotive force E decreased within 20 to 30 min to zero corresponding to a Ag/S ratio of 2.003 and became negative, indicating a value of aAg> 1. A representative plot electromotive force E vs time is shown in Fig. 2. The minimum of the electromotive force characteristic of the onset of

Jan 1, 1963

By H. M. Howe

On commencing the construction of the Orford Company's copper smelting works, at Bergen Point, N. J., I endeavored to convince our President, Mr. W. E. C. Eustis, by actual tests, that at the pressure of from 15 to 18 ounces per square inch, employed by us in smelting, less power was consumed in delivering a unit of blast by a Baker blower than by a fan blower. I attempted to prove this in the following manner: Across the mouth of a No. 5) Baker blower I firmly fastened a board with two round holes, 6 inches in diameter, cut in it. The board was fastened so tightly that no air could escape except through the holes. I then drove the blower at several differerent speeds, observing the pressure at which the air excaped through the two openings for each different speed of the blower, and also indicating the engine, whose only work at that time was to drive the blower. From this I calculated the quantity of power required to deliver, with a Baker blower, sufficient air to keep the pressure at a given point, while it escaped freely through the two six-inch apertures into the open air; or, in other words, to deliver air at a given pressure through these two openings. From the total power so consumed it was, of course, necessary to deduct the power which was required to drive the engine itself. This was ascertained by removing from the engine the belt which drove the blower, and then noting the quantity of power consumed in simply turning the engine over without any

Jan 1, 1882

By G. F. Dillion, A. F. Armington

THE present method for the ultrapurification of boron involves the formation, distillation, and decomposition of boron tribromide.' However, the boron tribromide prepared contains several impurities in the ppm range, even after distillation. Some of these impurities, notably carbon, can be reduced after decomposition by zone refining. In this study, a comparison of the purity of boron tribromide at various formation temperatures is presented. The apparatus employed consisted of a bromine flask connected to a 22 mm ID horizontal quartz reaction tube packed with amorphous boron powder, which was in turn connected to a receiving flask cooled with an ice bath. Argon was used as a carrier gas. The approximate rate of passage of bromine to the reaction tube was 25 g per hr. The reaction was first investigated at several temperatures in order to determine the lowest temperature necessary to produce a colorless product which was assumed to be an indication of complete reaction of the bromine. The lowest temperature found in this study was 420oC. The amount of impurities found in the boron tribromide at various formation temperatures is shown in Table I. The data presented are emission spectroscopic results of boric oxide produced by the hydrolysis of 2 to 3 g of boron tribromide in 10 ml of distilled water. After hydrolysis, the samples were dried several hours on a hot plate. Assuming equilibrium conditions in the reactor, one can make approximate thermodynamic calculations estimatling the completeness of reaction of bromine with boron and its impurities at various temperatures. Data for these calculations were taken from Rossini,3 and must be taken as approximations since the T?S factor was not included in the calculations. The results of such calculations indicate that, with the exception of carbon bromina-tion, all impurities would react almost to completeness (> 99 pet) at all temperatures between 400" and 900oC. In the case of carbon, which cannot be accurately analyzed spectroscopically, it is estimated that only about one sixth as much carbon tetrabromide would be formed at 400" than at 900°C. Since some marked reductions in impurity content were observed at the lower reaction temperature which would not be predicted by thermo-

Jan 1, 1962

By Sir John Cadman

Since my previous review of the Persian fields, presented in 1929,' considerable progress has been made. The main feature of drilling development has been the delimitation of the Haft Kel field and its extensions. Although the limits have not yet been reached, a productive area of about 40 square miles has already been proved and it is now certain that the field will be of the same order of importance as the Masjid-i-Sulaiman field. Production to main pipe line from Haft Kel was begun in November, 1929, and to date about 4,500,000 tons have been produced. Normal production has continued from the Masjid-i-Sulaiman and Naft Khaneh fields. The search for oil in horizons below the main producing limestone is perhaps the most interesting and important exploratory drilling work in progress. Promising results have been obtained in the first well deepened in the Masjid-i-Sulaiman field with this objective, and the exploration of these lower formations is being continued. In this connection an allied program of geochemical research work on the nature of the oils and oil-bearing rocks of different horizons is at, present being undertaken. Masjid-i-Sulaiman Field Since the Haft Kel field was brought into production in 1929, production from Masjid-i-Sulaiman has been reduced in order to equalize to some extent the producing lives of the two fields. The production for the last four years has been as follows: m Approximate Equivalent in TonB Barrels 1929 5,434,071 38,038,497 1930 4,925,869 34,481,083 1931 4,248,086 29,736,602 1932 Approximately 4,500,000 31,500,000

Jan 1, 1933

By R. W. Armstrong, P. C. Jindal

The hardness dependence on grain size for polycrys-talline cartridge brass and a leaded brass has been measured by Brine11 and Rockwell B testing. In each case, the hardness, H, depends on the average grain diameter, 1, according to: H =Ho + kHl-1/2 where Ho and kH are experimental constants. Diamond pyramid hardness values have also been measured as a function of the indentation size and grain size to give additional information on the nature of the hardness test and the dependence of hardness on micro-structure. The hardness of polycrystalline brass depends on its grain size. Bassett and Davis' demonstrated this as early as 1919 by making Brinell hardness measurements on cartridge brass. Since then, the hardness of this type of material has been measured as a function of grain size by making Rockwell,2'3 Vickers,4 and Brinell5 tests. he hardness dependence on grain size has also been measured for other materials. Angus and summers6 investigated the grain size dependence of the Brinell hardness of polycrystalline copper and a Cu-4.5 pct Sn bronze. In other studies, nickel,? Armco iron,Big an Fe-0.07 pct C alloy,I0 and an 0.39 pct C-12.45 pct Cr stainless steel" have been investigated. In some of the preceding cases, the hardness results have been analyzed to show that the hardness varies with the average grain diameter, 1, according to an l-l\4, l-1/4 or I-2 dependence,11-13 The studies of the influence of grain size on hardness have not been based on any theoretical model. This may be because the hardness of a material is itself a complicated property. However, attempts have been made to correlate, experimentally and theoretically, the hardness of a material with its unidirectional stress-strain behavior.14-l6 On this basis, Hall" proposed that the polycrystal hardness dependence on grain size might follow directly from the Hall-Petch18,19 relation for the grain size dependence of the yield stress. Thus, the hardness-grain size relation was given as: H = Ho + kHl-1/2 [1] where Ho and kH were taken as experimental constants. The relation was applied to the measurements on brass,' copper,6 bronze,= and Armco iron.' More recently, this relation was shown by Armstrong and jindal20 to adequately describe the measurements on cartridge brass made by Bassett and Davis' and Babyak and Rhines.5 In this case, the relationship was taken a step further by independently relating the values of Ho and kH to the values of oyand ky, previously reported by Armstrong, Codd, Douthwaite, and petch21 from measurements of the yield stress dependence on grain size for this type of material. In the present investigation, new Brinell and Rockwell B hardness measurements have been made as a function of grain size for a cartridge brass and a leaded brass. In addition, diamond pyramid hardness values were measured as a function of the indentation size. All these results are applied to a further analysis of the hardness dependence on grain size. MATERIALS AND EXPERIMENTAL METHODS Cartridge brass and a leaded brass were selected for this investigation for two main reasons: it was anticipated 1) that these materials could be cold-worked and recrystallized to a wide range in grain size and 2) that the results to be obtained on these typical industrial materials could be usefully compared with previous investigations. The chemical analyses of the actual materials which were employed are given in Table I. The as-received 1/2- and 3/4-in.-thick plates were given various reductions in thickness by cold rolling. The rolled material was heat-treated at various temperatures between 330" and 850°C for differing time periods from 5 min to 9 hr to achieve a variation in the average grain diameter between 0.0339 and 0.000543 cm.22 During heat treatment, the brass was protected from zinc loss by packing it in chips or foils of the same composition material. Reasonably equi-axed grain structures were obtained in each case. The metallurgical grain sizes of the specimens were determined from measurements of the average linear intercept on a random line. Annealing twin interfaces were not counted along with grain boundaries. The

Jan 1, 1970

Members of the American Institute of Mining and Metallurgica Engineers can now secure copies of the Journal of the Institute of Metals of Great Britain at a special price of $5 for the two volumes issued during the year, postage extra amounting to approximately 25 cents. This Journal is one of the best books dealing with the subject of non-ferrous metals and alloys and this arrangement with the Institute of Metals permits our members to take advantage of this specially low price. Back numbers of the Journal can be purchased on the same basis. The Journal can be ordered directly through the office of the Institute of Metals, Great Britain 36 Victoria St., Westminster, S. W. I., London, England. The letter should be accompanied by an international money order and a copy sent to Secretary of the A. I. M. E. in order that the membership record may be checked.

Jan 9, 1919

By R. H. Atkinson, R. N. Rhoda

An improved technique has been developed for the deoxidation of palladium with aluminum which is especially suitable for use in making small castings with an induction-melting and casting machine. The effect of various crucible linings on the efficiency of the residual deoxidizer and accompanying oxide film in protecting palladium against oxidation during remelting also has been examined; the preferred crucible lining consists of zirconia cement. THE objective of this work was to develop a simple method of deoxidizing induction-melted palladium which would be suitable for use by manufacturers of jewelry and other small castings. In a common method of deoxidizing torch-melted palladium a piece of aluminum foil is dropped on the surface of the molten metal. If a film is present, which is usually the case, it must first be removed by oxidizing the molten metal thoroughly because it would interfere with the entry of the aluminum into the melt. Removal of the film is probably facilitated by a mild fluxing action of the silica crucibles which are used for torch-melting. However, removal of an alumina film from molten palladium in the crucibles normally used for induction melting is a much slower process and it became necessary to modify the de-oxidation procedure. In the modified procedure the charge is simply melted and the desired amount of aluminum, crimped to one end of a tungsten wire, is plunged through the film into the palladium and the wire immediately withdrawn. The trace of tungsten which dissolves along with the aluminum can be avoided, if considered objectionable, by using a palladium wire. In view of the persistence of the alumina film under the conditions of induction-melting it also was decided to ascertain the efficiency of this film in protecting palladium against oxidation during repeated remelting and casting. Melting Equipment and Materials The equipment used for melting and casting consisted of an Ecco GC:6, 6 to 8-kva high-frequency converter and an Ecco M34B centrifugal casting machine. This unit is being increasingly used for making jewelry and dental castings and it also has been found useful in making exploratory melts of a variety of nickel alloys, for which purpose it is well suited on account of its speed of melting and economy of material. A description of the machine and its operation will be published elsewhere.' A common palladium jewelry alloy, 95.5 palladi-um-4.5 ruthenium (referred to as "palladium" in the trade), was selected for the deoxidation tests. It was available as melting stock which had been melted in air to free it from oxidizable impurities, and also as clean scrap from previous melts which had been deoxidized with aluminum. The latter was thought to be typical of clean "palladium" scrap to be found in a manufacturing jeweler's establishment and it is also similar to one brand of "casting palladium." By the same token, the oxidized melting stock corresponds to "casting palladium" after the latter has been melted and thoroughly oxidized: Pure aluminum wire (99.9 pet), 0.032 in. diam; 1 in. = 0.036 g. Scrap tungsten wire, 0.014 to 0.020 in. diam. Argon, commercial water-pumped; 99.9 pet pure Experimental Procedure Samples of about 50 to 75 g of the palladium alloy were melted in a crucible lined with a proprietary refractory alumina cement. Some charges were melted in air, others in argon. The oxidized melting stock was melted and solidified a number of times in order to remove as much oxygen as possible before deoxidizing, but this treatment was unnecessary in the case of scrap. In either case the metal was deoxidized with aluminum (0.01 to 0.05 pet) by the

Jan 1, 1959

By Samuel Hoyt

SOME of the more important properties of finished materials are strength, ductility, toughness, resistance to alternating and repeated stresses, etc: Of these, the property that appears to have received the least consideration, at least in this country, is toughness, which is clue, possibly, to our regarding toughness as a qualitative property or, at any rate, as one that, parallels ductility. This arises out of our greater experience with the simple carbon steels in the rolled or forged (non-heat-treated) condition which, qualitatively, are tough if ductile and are not tough if brittle. In this way we have erroneously become, accustomed to judging the toughness of a material from its behavior in the tensile or similar test. The point of view presented in the present paper is that toughness, like hardness or tensile strength, should be regarded as an independent property and of sufficient importance to require, in so far as that may be possible, quantitative determinations. If such be true, it becomes at once necessary to devise experimental means for measuring, or valuating toughness, and the notched-bar impact test (the Charpy test) is advanced as the most logical test that has so far been developed for this purpose. It is further advanced, with particular emphasis, that we have two kinds of toughness to deal with and, accordingly, they will be dealt with independently. CLASSIFICATION OF MATERIALS ACCORDING TO TOUGHNESS Toughness has been defined somewhat as follows: Tough materials are those that offer considerable resistance to permanent deformation but which, once such resistance has been overcome, may' be deformed plastically, but only by the expenditure of considerable energy. In other words; tough materials may be deformed plastically but they absorb a considerable amount of work in the process. This kind of toughness may be called "static" toughness when the rate of loading is reasonably slow or "dynamic" toughness when the rate of loading is

Jan 2, 1919

By L. Adler

Longwall caving, one of the most economical and attractive mining methods, is yet one of the most difficult and hazardous.1 This dualism is inherent in a method which manipulates the mine supports themselves to aid in excavation. The difficulty is further compounded by the lack of an analytical method to predict and control results. This paper is intended to meet this need by providing a first approximation to the mechanics involved. The analysis will be limited to materials which are linear-elastic, homogeneous and isotropic. The rock structure is assumed to consist of beds of uniform thickness with no interbed bonding.2 Consequently, the mine roof can be likened to a beam, in which the action characteristic of longwall caving is the controlled deflection of the barrier supports. This deflection causes load to be intentionally transferred from these barrier props to the working face.3 Two of the requirements of this method, shared in common with other mining methods, are the provision of (1) adequate and (2) safe working space. The third requirement is the one characteristic of longwall caving and is somewhat in conflict with the second; (3) the development of near-failure static loads at the face. Requirement (1) is handled by spacing the barrier props sufficiently far from the working face for efficient operation. Requirement (2) limits the static stresses in the structure to predetermined allowable values. This means that it is not desirable to induce a maximum load on the working face as requirement (3) may imply. Such a condition could produce collapse in the whole structure. It is the purpose of the undercut to limit the depth, and thereby control the failure of the face. Therefore, requirement (3) really means the development of an optimum, not maximum, load which, in conjunction with undercutting, produces failure at the working face, with minimum powder consumption. Stress analysis requires an exact delineation of the structure and loads. The structure will be defined as the immediate roof and its supports. Since the roof is severed at the caving line, the supports reduce to the barrier props and the working face, as shown in Fig. 1. The mechanics of failure within the working face itself are complex and beyond the scope of this study, since the face represents a typical mine invert structure.4 However, this lack can be made good by the judicious collection of field data. The primary load on the structure is its own weight or body load which can be considered uniformly distributed over its upper surface. Additional loading occurs due to interference of overbeds with the structure. Wherever this occurs, the effect can be approximated by a load uniformly distributed on the upper surface of the structure.5 When this interference is intermittent, as with a much thicker overbed, the elastic curve for the overbed is superimposed on that for the structure and the extent of interference noted, as Fig. 2 shows. However, for simplicity, this study will ignore such intermittent loads without impairing the generality of approach. Consequently, the free-body diagram is that of a uniformly loaded cantilever beam with an inter-mediate support, as shown in Fig. 3. For convenience of analysis, the diagram will be divided just to the

Jan 1, 1961

By Arne Bergholm

Australian rutile was chlorinated in the presence of CO or carbon. The chlorination velocity in CO was found to be strongly influenced by temperature and proportional to the CO concentration, but independent of the Cl, concentration. In the presence of carbon, the reaction velocity is much higher. The reactivity of the carbon and the distance between the carbon and the rutile surfaces are important variables. The reaction velocity is approximately proportional to the Cl, concentration and independent of the CO concentration of the surrounding atmosphere. Experiments with fluidized-bed chlorination of carbon-rutile mixtures indicate that the motion of the bed has little influence on the reaction velocity. At low temperatures, the chlorination velocity of dense tablets is much greater than that of TiO, coke mixtures suitable for fluidization. The reaction mechanism is discussed. In the industrial production of TiCl, rutile is chlorinated in the presence of carbon. Disregarding intermediate steps, the reaction may be expressed by the following equations: The ultimate object of this study was to find out whether the reaction velocity was higher in fluidized bed operation compared with chlorination of pelle-tized carbon-rutile mixtures. From a literature survey and preliminary experiments it was learned that some basic knowledge about the reaction mechanism was needed for a good experimental design. Therefore the following sets of experiments were carried out: 1) Studies on the reaction velocity in the chlorination of rutile with CO as the only reducing agent. 2) Chlorination of separate rutile-carbon tablets. 3) Chlorination of rutile-carbon tablets at different temperatures with various kinds of carbon, various grain sizes, and various tablet-making techniques. This series of experiments was carried out not only with pure chlorine but also with mixtures of chlorine with argon, CO and CO,. 4) Chlorination of rutile-carbon tablets made in a strictly standardized manner. 5) Chlorination of static-bed rutile-carbon mixtures. 6) Fluidized-bed chlorination of the same mixture. The experiments 4 to 6 formed the final and direct test of the main question: Static bed vs fluidized bedo. Although there are many patents and papers dealing with the general aspects of chlorination, only few experiments from which detailed information can be obtained have been reported in the literature. Pamfilov and coworkersl3 have studied chlorination of TiO, with CO or carbon as the reducing agent. They found that the weight decrease per hour at 600o to 800°C amounted to 11 to 14 pct with CO and 45 to 51 pct with carbon. They suggest that phosgene might be an intermediate in the chlorination of TiO,. Takimoto and Hattori have chlorinated reduced titanium oxide (TiO) and found a very high rate of TiC1, -production. They proved that the composition of the gas from the chlorination of rutile-carbon mixtures contained mainly CO. They reported for instance 74.7 pct CO, and 5.6 pct CO at 800°C at which temperature the Boudouard equilibrium composition is 12 pct CO and 88 pct CO. Seligman and Segerchano6 have studied the chlorination of TiO. They proved that Ti0 and chlorine react rather rapidly at temperatures as low as 300°C. Above 400°C, the reaction was complete. At 500°C the velocity of this reaction was much higher than was chlorination of TiO, + C. McTaggart,7 Nishimura, et al. and Wilskam have chlorinated mixtures of carbon and various kinds of rutile or beneficated ilmenite. Nishimura, et al. also report the results from reduction of TiO, with H2, CO, or carbon. At 900°C only 1 pct Ti O is formed in 2 hrs. At 1100°C 23.1 pct Ti, 0, was formed if elementary carbon was present. No carbide formation occurred below 1400°C. McIntosh and Cofferll have observed that the CO, content of the exit gases from chlorination of rutile and calcined petroleum coke is appreciably higher than found in the Boudouard equilibrium. At 900°C the ratio (CO, /CO + CO) is about 80 pct, whereas the equilibrium value is about 2 pct. W. E. Dunn12 has studied the chlorination rates of several TiO,-bearing minerals with CO + Cl, or COCl . Chlorinations were carried out either in a fluidized reactor or a fixed-bed reactor, both having a 30-mm diameter. The results obtained in both reactors were comparable. It was proved that benefi-ciated ilmenite (i.e., ilmenite from which the iron oxide had been removed by chlorination) was chlorinated 10 times faster thanrutile. Sore1 slag showed an intermediate rate. When phosgene is used, the

Jan 1, 1962

The regular activities of the Institute are financed mainly by income derived from members' dues, from advertising in MINING AND METALLURGY, and from the sale of publications to the public. In addition, collateral activities and special projects are financed each year by means of income from endowed funds controlled and administered by the Institute. In the aggregate, the principal sums of these endowments amount to more than $530,000. An active effort is being made to increase the endowment funds of the Institute through a standing committee, of which H. T. Hamilton is chairman, and of which the other members are: W. H. Aldridge, George D. Barron, Cleveland E. Dodge, D. C. Jackling, Henry Krumb and J. V. W. Reynders. This committee feels that there exists a tremendous opportunity for the Institute to be of ever-growing service to the public, to the mineral industries, and to the profession. It welcomes suggestions as to names of men of means who are vitally interested in the mineral industries, and to whom the opportunity to make a contribution or bequest might appeal favorably if presented in the proper light by the committee.

Jan 1, 1941

By A. R. Marder

Fe-C alloys have been investigated at temperatures below the eutectoid transformation to determine whether the superplasticity phenomenon exists for these materials. As a result of void formation at the carbide-ferrite interfaces that led to void coalescence and premature failure, the large elongations characteristic of superplustic matem'als did not develop. It had generally been assumed that the conditions for obtaining superplasticity include: a) T/Tm =0.5, b) a strain rate sensitivity of the flow stress that results in m s 0.3, and c) fine-grain structure. Although superphsticity was not observed in the alloys studied, stress-strain rate measurements indicated that an additional condition for the existence of superplasticitv in Fe-C allovs is that the fine-wain structure be equiaxed in agveement with previous results on Zn-Al al1oys. MANY investigations have been made on the hot deformation of iron-base alloys in order to obtain an understanding of the variables that may affect high-temperature strength and ductility.'-6 However, only a few papers have studied the effect of carbon content on the high-temperature properties of iron-base alloys. Peretayat'ko and Zaikov and Wallquist and carlen4 studied the effect of carbon on strength in the y temperature range, and recently Robbins, Shepard, and sherby6 studied the influence of carbon on the torsional behavior of iron in the a and cu-plus-cemen-tite temperature ranges. In addition to studying hot deformation behavior, current investigations have also been concerned with the phenomenon of superplasticity in nonferrous materials, and, in particular, ferrous alloys. Superplasticity is identified by the increased resistance to necking that results from a high strain rate sensitivity of the flow tress. ackofenr proposed the strain rate hardening coefficient m = d log a/d log e as a measure of strain rate sensitivity and showed that m must be "-0.3 for superplasticity to exist. In addition, a fine-grained microstrcture,- a eutectic or eutectoid ornosition,- and a test temperature in the creep range (TITm > 0.5)" have also been advanced as necessary conditions for superplasticity. Although many workers""23 investigated superplasticity associated with the allotropic transformation in iron and the eutectoid transformation in steel, and recently chadler " and orrison have studied superplasticity in the a - y phase region, no one has measured the superplastic effect in the a + cementite temperature region. Therefore, the purpose of this investiga- tion was to determine the effect of carbon content, microstructure, and test temperature on the strain rate sensitivity of Fe-C alloys at temperatures below the eulectoid transformation. EXPERIMENTAL PROCEDURE Fe-C alloys with carbon contents of 0.2, 0.4, 0.6, 0.8, and 1.0 wt pct were prepared as 100 lb 54 in. ingots by vacuum-induction melting. The compositions are listed in Table I. All the ingots were soaked at 2100°F for 2 hr prior to rolling to 4 in. plate. The minimum finishing temperature for rolling was 1800°F. The plate was sheared in 10-in. lengths and tensile bars were rough-machined prior to heat treatment. The samples were heat-treated according to the schedule in Table I1 in order to obtain a fine-grained microstructure consisting of finely dispersed carbides in a matrix of small ferrite grains. All the tensile specimens were heat-treated prior to finish machining, and tensile testing was accomplished on an Instron machine in conjunction with a clamshell furnace. The buttonhead specimen configuration is shown in Fig. 1. An inert atmosphere, helium, was maintained during testing with a steel tube shroud in a bell jar arrangement. Predried helium was continually purged over the buttonhead specimens and exhausted through ceramic fiber at the bottom of the tube to keep oxidation at a minimum and to prevent

Jan 1, 1970

By Herbert Lang

Cord-wood, sawn into blocks of about a foot in length, is a regular constituent of our fuel-charge at Mineral, Idaho, our work being the matting of silver-ores by fusion in a blast-furnace. The furnace is a round water-jacket furnace, of 36 inches diameter at the tuyeres, and the charge of smelting-mixture weighs 950 Ibs., requiring 110 Ibs. of Connellsville coke to drive it. I replace half this coke with 135 lbs. of fir-wood, cut from dead and apparently perfectly dry trees. This mixtrire produces as high a sn~elting-temperature as all coke, whence I infer that the smel ting-effeot of a given weight of wood is to that of the same weight of coke as 11 to 27, or 1 to 25/11. A cord of wood sawed ready for use weighs 2840 lbs., costs $5.00, and is

Jan 1, 1892