Search Documents

By J. F. Tavernelli, L. F. Coffin

The deformation and fracture characteristics of eight metals subjected to fully reversed cyclic strain ranging from 0.2 to 50 pct were investigated at room temperature. Strain-hardening characteristics unique to the interna1 structure of a particular metal were found. Complete removal of the strain-hardening effects resulting from prior deformation was brought about by subsequent cyclic strain. Further support for the validity of the inverse relationship between the plastic strain range and the square root of the number of cycles for failure is given. THE resistance of materials to cyclic plastic strain is of interest both from a fundamental and practical point of view. It is now a well-accepted fact that fatigue failure in metals is a consequence of the localized slip deformation which occurs within the individual crystals of metal.'-' Hence the failure process should be strongly dependent upon the magnitude of the gross cyclic plastic deformation of the metal under conditions where this is a measurable quantity. Therefore, an experimental investigation of metals in which the cyclic plastic strain is the independent variable should shed new light on some of the basic aspects of the problem. From the practical point of view, there are many uses for information relating to the cyclic strain resistance of metals. One is the case of thermal stress fatigue where fatigue failure can occur as a consequence of a com- paratively few cycles of thermally induced mechanical deformation. Another is the mechanical working of metals where large cyclic strains are employed. In recent years several publications have appeared relating to the cyclic-strain resistance of metals,8-11 dealing mostly with the fracture aspects where the temperature is cycled simultaneously with the mechanical strain. Some work has been reported on the cyclic-strain resistance of metals at constant temperature, again oriented more toward the fracture aspects of the problem than the deformation aspects. 12-16 The present research investigation was undertaken to obtain information regarding the deformation characteristics of several metals whose structure-property relationships were simple and straightforward under conditions of both cyclic and monotonic strain. It has been shown for example that under cyclic-strain conditions some materials will strain harden, while other materials, particularly cold-worked structures, strain soften and these effects required further clarification.8,17-19 It was also de-

Jan 1, 1960

By J. Phillip Neal, Kefton H. Teague, Carroll P. Rogers

Feldspars, the most abundant minerals of the igneous rocks, occur in numerous forms and mixtures. The feldspars of commercial significance are found in widely distributed pegmatites as large crystals usually free of iron-bearing impurities and thus suitable for hand-cobbing, and also in larger bodies where the ore contains various types of feldspar intermingled with quartz and relatively free of iron-bearing impurities, or at least readily unlocked from impurities present at relatively coarse mesh. The latter type of ore includes some pegmatites, and the "alaskite" bodies so common in the Spruce Pine district of North Carolina. On the west coast of the US and in Oklahoma there is-or has been-commercial recovery of natural feldspathic sand as a source of alumina in glass and ceramics. "Aplite" in commercial terminology is a light-colored igneous rock with a granitic composition and a fine sugary texture, often banded with readily removable iron impurities. Only one area in Virginia produces aplite for the glass industry; it is located near Montpelier in Hanover County. According to Deer et al. (1966) the word feldspar derives from the Swedish feldt or jolt (field) and "spath:" chunks of rock appearing in tilled ground overlying granite. Castle and Gillson (1960) indicate a Germanic origin, citing "spat," which is said to refer to any transparent or translucent material which is readily cleavable. The term "spar" has in the past been applied to minerals other than feldspar, such as barite, calcite, and fluorite. It is correct to call the latter "fluorspar." There is a true barium feldspar, but it is rare and of no present economic importance. What is recognized as feldspar or "spar" by present producers and consumers consists of three silicate minerals which, if pure, would have the formulas KA1Si3O8 (microcline or orthoclase), NaAlSi3O8 (albite), and CaAl2Si2O8 (anorthite). These are almost never found in pure form in nature, but occur together in great abundance in a three-component system. A considerable number of different combined ratios of these three exists, with the exception that isomorphism between potassium spar and calcium spar is very limited. User specifications for feldspar products are largely built around the prevalent naturally occurring ratios. Passages following will refer to "K-spar," "Naspar," or "Ca-spar." Nomenclature and Descriptive Terms Relating to both the mineralogy and the economics of feldspar are certain terms whose coverage it is useful to specify. Commercially, aplite is a feldspathic rock mined and beneficiated in one location in Virginia, in which both titanium and feldspar minerals are present-the latter now being the major, if not the only, economic product. Technically, the term aplite when applied to this rock is of questionable accuracy. But, in light of accepted commercial usage, the term will be here used to designate it. Regarding the Virginia rock, Ross (1941) is cited. Alaskite is another term requiring understanding if not precise use. A distinctive rock type customarily called by this name is found near Spruce Pine, Mitchell County, North Carolina. An important major feldspar source, it contains somewhat higher levels of plagioclase feldspar and quartz than alaskite as defined in the Glossary of Geology and Related Sciences, which states that `orthoclase, microcline, and subordinate quartz are the principal

Jan 1, 1983

By Josef Intrater

A dilatometric determination of the a + ß region temperature limits was performed on vacuum melted Zircaloy-2. The temperature of transformation for a-a+ß and a+ß — ß on heating and cooling as a function of rate of heating and heat treating history was studied. The limits were found to be 815° to 830°C to 975° to 995°C on heating and from 960° to 930°C to 785° to 770°C on cooling. A 5° to 15°C increase was observed for a- a + ß with increased rate of heating and a 20° to 30°C decrease for ß - a + ß with increased rate of cooling. 1 HE transformation temperature for pure zirconium has been determined by many investigators1-5 using metallography, electrical resistivity measurements, and dilatometry. The effect of the rate of cooling on the transformation temperature of zirconium has been studied by Hayes and Kaufmann6 and Duwez,7 and the effect of alloying elements by pfei18 and McGeary.13 Since the development of Zircaloy-2, the limits of the a + ß region for that alloy have been also determined. The first reported temperature for the a — a + a transformation in Zircaloy-2 was 900°C and for a + ß - ß 1000C Subsequent studies by Picklesimer and damson" indicated the beginning of the transformation at 810°C, and the metallographic study by the Technology Group of the Special Materials Section at the Westinghouse Bettis plant1' suggested that 820°to 830°C is the temperature of transformation. The dilatometric investigation by the latter group yielded 830°C for the beginning of the transformation. Thomas and Forscher12 set the beginning of the transformation at 900 °C on heating and the end of the transformation at 870°C on cooling. The above investigators stated in their paper that the dilatometric curve exhibits features caused by a eutectoid reac-

Jan 1, 1962

THE story of Miami really is two stories. First, that of an excellent Porphyry Copper mine, ably managed as a business enterprise, and always among the leaders in technical progress. Concentrating its first ore in 1911, it had by 1925 paid dividends totaling $30,000,000 or $40 per share on stock that had cost the public $5 per share in March, 1908. The ore, containing 2.5 per cent copper at the start, had become progressively leaner but the recovery had tended to improve. Production costs had gone up during the World War and the early post-war period; and had come down again. In all these respects it had followed the norm. If the mine had been abandoned as exhausted and the company had been liquidated late in 1925 (a program that had been given earnest consideration in 1924), Miami would have gone down into history a first-rate mining venture; as an active and progressive participant in the great Porphyry achievement. But Miami was not liquidated in 1925; instead it started to write the record of its second and really amazing story. Near the old mine was a large body of low-grade ore containing, in place, less than 20 lb. of copper to the ton, and without, incident- ally, any considerable sweetening of gold and silver. Any method of underground mining that was cheap enough would certainly entail some dilution, so that ore as sent to the concentrator necessarily would average much less than 20 lb. As a matter of record, the average for 1929 was 16.6 lb., from which 11.726 lb. was recovered as concentrate. As already said, the exhaustion of the older orebody during 1925 was foreseen; but in 1924 the decision was reached to enlarge the concentrator and develop a new mine. An expenditure of $2,500,000 was entailed in this program. By October, 1925, the

Jan 1, 1933

By Paul L. Russell

7.5-1. introduction. The possible engineering uses of nuclear explosives were recognized with the first nuclear detonation. Subsequent experiments have demonstrated the ability of nuclear explosives to move very large volumes of rock and earth efficiently and at costs below conventional earth-moving methods. The ability to package a quantity of energy equivalent to a few million tons of conventional explosive in a container approximately 20 ft long and 36 in. in diameter enables easy emplacement and thus provides the potential for excavation on scales heretofore impossible. Space does not permit detailed discussion of the many experiments with conventional high explosives and with nuclear explosives that were performed in developing the information presented here. A bibliography is included for those wishing detailed information. Material from those sources and from personal experience has been used freely. 7.5-2. Nuclear Explosives. An explosion, in general, results from the very rapid release of a large quantity of energy within a limited space. This is equally true for both conventional and nuclear explosions, although the energy is produced in quite different ways. In the case of a conventional explosive, this energy arises from chemical reactions. In a nuclear explosion, the energy is produced as a result of the formation of different atomic nuclei by the redistribution of the protons and neutrons within the interacting nuclei. Nuclear energy is of a much higher order of magnitude than chemical energy when equal masses are considered, and the release of this energy is a thousand times more rapid than the fastest chemical detonations. Explosions may be produced by fission or fusion reactions. FISSION. When a free (or unattached) neutron enters the nucleus of a fissionable atom, it can cause the nucleus to split into two smaller parts. This fission process is accompanied by the release of a large quantity of energy. The complete fission of 1 lb of uranium can produce as much energy as an explosion of 9,000 tons of TNT.

Jan 1, 1968

By H. Kahata, I. Iwasaki, Y. Takahasi

A combined process of segregation roasting-flota-tion or magnetic separation was developed to recover nickel from lateritic iron ores and oxidized nickel ores. An ore was mixed with a halide, such as sodium or calcium chloride, and a solid reductant, and roasted, whereby the nickel content was segregated out as discrete metallic particles. Either by magnetic separation, or by flotation using a sulfhydryl collector together with a heavy metal salt as an activator, the metallic nickel could be concentrated, Effects of such variables as the types and amounts of the halide and solid reductant addition and of the roasting conditions were extensively investigated. The concentration results on several types of ores from Japan, the Philippines, and New Caledonia are presented. Laterite is a residual product of rock decay in tropical and subtropical regions, and consists mainly of hydrated oxides of iron and alumina. Those derived from serpentine sometimes become enriched in nickel, cobalt, and chromium contents. Oxidized nickel ores are of the similar origin, but their nickel as well as silica contents are higher due to gamierite-type silicates. Apparently, nickel enrichment is more pronounced in the transition region between the surface layer of iron laterite and the underlying serpentine. Iron laterites often contain over 50% iron, and their reserve is reported to exceed 22 billion tons, corresponding approximately to 20% of the world iron ore reserve.1 It is readily apparent, therefore, why the iron laterites have attracted much attention of the steel industry as a potential source of iron ores. Numerous attempts to remove nickel and chromium as byproducts, have been reported in literature.' Worldwide discoveries of high-grade iron ore deposits in recent years have inevitably lessened the interests in iron laterites. However, in view of the tremendous potential for their gross value and supplies of nickel, cobalt, chromium, and alumina along with iron, the problem remains as a challenge. Much of the chromium in laterites is present in the form of relatively coarse particles of chromite, and various classification methods have successfully been applied for its removal.2,3 The nickel, however, is intimately associated with limonite, and ordinary concentration techniques are totally ineffective. Much attention has, therefore, been given to hydro-metallurgical or pyrometallurgical means. Yet, all the known processes appear to have limitations either economically or for the use of products as iron raw materials due to a high residual content of nickel. Some attempts have been made to pre-roast laterites or oxidized nickel ores, particularly with sulfidizing agents, and to remove nickel either by magnetic separation,' or by flotation.4 It is apparent that any such concentration process would require grain growth of nickel during roasting for effective separation. Oxidized copper ores are reported to be concentrated by the segregation roasting-flotation process,5 in which the ores are roasted with a chloridizing agent and a carbonaceous reductant in order to promote the growth of metallic copper through repeated cycles of copper chloride volatilization and its reduction on the solid reductant surfaces. Examination of a vapor pressure-temperature diagram of various metal chlorides indicates that a separation of nickel from iron may be effected by a similar process. In fact, the segregation roasting of laterites was reported to increase the extraction of nickel by the ammonia leach process, as compared to the ordinary reduction roasting.6 In the present article some of the preliminary experimental results of the segregation roasting, followed by either flotation or magnetic separation, on laterites and oxidized nickel ores are reported. The effects of various parameters in the roasting as well as in the concentration steps are discussed. MATERIALS AND METHODS An oxidized nickel ore from Thio, New Caledonia, and three laterites from Homonhon, the Philippines, Wakasa and Miyagawa, Japan, were selected for the

Jan 1, 1967

By C. D. Hunter, I. B. Browning, N. W. Shiarella

During the year 1936 improvement in the oil industry in Kentucky continued at about the same rate as shown by that of the year 1935 over the year 1934. The development of several new pools in western Kentucky and the increase in the application of repressuring methods to the old fields of eastern and to a lesser extent of western Kentucky increased the total production to 5,481,227 bbl., as compared to 5,175,054 produced in 1935. The principle sources of this increased production are the Livermore field and the new Bates Knob field in McLean County, in western Kentucky, and the result of repressuring operations in the " Corniferous" pools of Lee, Powell, Wolfe, Morgan and Estill Counties and the "Weir" sand (of Mississippian age) fields of Magoffin, Lawrence and Johnson Counties in northeastern Kentucky. The last named fields have a producing sand especially adaptable to these methods. Drilling No new fields were opened in eastern Kentucky during the year. All new drilling was codned to pressure wells and new oil wells to complete patterns around the intake wells. Owing to the relatively low "initial" or flush production of the wells in this section—even though the ultimate recovery per acre is as large—higher prices for crude will have to prevail before extensive search for new fields is begun; as in northwestern Kentucky, where active exploratory work has been carried on as in the several preceding years, resulting in numerous new and prolific, although comparatively small fields. In this section approximately 500 new oil wells drilled in the Owensboro field, embracing several pools in Ohio, Hancock, Daviess, McLean, Henderson, Webster and Nuhlenberg Counties in the northwestern part of the state. The total oil production for this field during 1936 exceeded by many thousand barrels the 2,821,722 bbl. produced in 1935. In these fields the producing sands range from the middle Missis-

Jan 1, 1937

By G. S. Cole, G. F. Bolling

ThIS note accompanies a study of grain structure changes in metal ingots produced by the alteration of fluid motion.1 Although the Prandtl Number of aqueous solutions is much higher than that for metals, it is quite instructive to see the simulation of freezing, as pointed out by Jackson and coworkers.2-4 Accordingly we have observed the effects of natural thermal convection, the changes induced by a steady-state rotation in one direction, and the changes under oscillation.' Temperature measurements were made under duplicate conditions whenever the visual observations appeared interesting. A solution of 15 pct NH4C1 in water was chosen. In each case the solution was preheated to 90°C in a 4-in.-diam Pyrex beaker filled to a level of about 5-in. depth and covered to prevent convective air cooling. The beaker was then placed in a container of iced brine, suitably arranged on a rotating table for movement about its cylindrical axis. Upon immersion in the brine under static conditions, fluid flow was observed near the wall of the beaker before the onset of crystallization, which generally commenced only after the temperature fell to 51.5"C. The region of flow extended about 1 mm from the wall and could not be observed elsewhere. The measured radial temperature increased sharply within 1 cm from the wall and thus over a distance considerably greater than that observed for the flow. However, we note that this difference of approximately one order of magnitude between hydrodynamic and thermal boundary layers should be expected for aqueous solutions, in contrast to metallic liquids. Beyond this layer the temperature was isothermal at a given height and in general nearly 10°C warmer than at the wall. The overall visual observation was therefore supported quite well by temperature measurement. There was also a vertical temperature gradient of nearly 2°C per cm throughout the liquid increasing from the colder bottom; this of course could not be observed visually. Eventually crystals precipitated from solution. (It

Jan 1, 1968

By WALTON H. HAMILTON

THE demand for "production control" has, like the poor, been with us always. With the development of the nation, the accumulation of business experience, and a maturing understanding of how our many and varied industries work, it is increasingly evident that an uncontrolled output is a source of great mischief and that order and performance demand a control of production. To see clearly the demand for "production control" we must look in detail at the ways in which industries operate. General pictures, grand aggregates, situations as "wholes," and smoothed curves are likely to be deceptive. An industry may seem to keep the even tenor of its ways, and yet the establishments which made it up may experience a great range of fortunes. A nice bundle of statistics may show in the aggregate a lovely regularity which is not shared by the firms which make up a trade. An industry may appear to be reasonably profitable, and yet the profits may be very unevenly distributed. The people in an industry, and dependent on it, are managers, laborers, stockholders, creatures of flesh and blood, such as you and I. General pictures and abstract statements must not blind us to what is happening to firms, corporations and individuals.

Jan 1, 1929

By Augustus Locke

WHY should I, a geologist, be coming before you to talk about finding ore? Certainly, the great discoveries of the past have not been made by geologists, but by men of very different tastes and training. If, in the year 1800, the course of ore discovery could have been foreseen, there would have been no reason to put it into the hands of geologists or other men of technical preparation. It was not geologists but explorers, Indian fighters, prospectors, manual laborers, and hardy financiers, who initiated the American mining industry. Then why this association of geological technique with ore finding? Why this feeling that the way to find ore is to apply to the problem what we call geo- logical principles? Well, to put it broadly, the old method has run out on us. It no longer works. Or, to put it another way, the cost of finding ore by the old method has mounted so high that one old district after another has become, practically speaking, dead, and various other old districts that are still going apparently at full strength are actually beginning to limp, and, with the cost of discovery mounting yearly, to fear, more than they will acknowledge, that the end is approaching.

Jan 1, 1926

By Faustino Roel

AMONG the problems confronting the mining engineer in Mexico in recent years, labor conflicts have come to occupy s prominent place. Each day they have become more serious and frequently have caused- the ruin of companies. It is therefore necessary for the engineer to understand the Federal Labor Law, the rights and obligations of companies and of their workmen, and the reasons for conflicts; to keep in mind the expense which may be caused companies; and to endeavor to avoid difficulties as far as possible. Our labor legislation is primarily to protect the workman and the constant tendency of the tribunals, including the Supreme Court of Justice, is to support the work- man in his demands against employer$, even at times granting him more than he asks, with no limit other than the economic capacity of the company to com-

Jan 1, 1937

By J. B. Cohen

EARLY investigators1-4 reported that additions of beryllium to silver caused embrittlement. The in-termetallic phases which are now known to exist5,' were not known at the time. Solidification appeared to occur by a simple eutectic reation.4,7 (The primary beryllium-rich phase appeared globular, when the liquidus temperature was near the melting point of pure beryllium, and angular when the liquidus was much lower; in discussion of Sloman's work,4 it was suggested that this difference was due to an intermetallic compound which was not revealed by the polishing technique.) In the investigation reported here, it was found that if the compounds now known to exist were avoided, certain beryllium-silver alloys containing large amounts of the primary beryllium phase possessed sufficient ductility to be cold formed. Alloys containing 14 and 20 at. pct Ag were prepared from vacuum-cast beryllium containing 1.0 to 1.2 pct impurities and silver, 99.99+ pct pure. The elements were melted together by induction in beryllia or alumina crucibles under argon at less than 1 atm pressure. The cooling rate was adjusted by regulating the temperature of the melt and by reducing the power to zero without stopping the water flow in the induction coils, which were in contact with the crucible. Ingots were about 0.75 in. in diam with a grain size of 0.12 to 0.25 in. Microscopic investigation of transverse or longitudinal sections of an ingot cast from a temperature well above its melting point showed that, in general, the compounds did not form, presumably because of rapid cooling; the alloys consisted of beryllium-rich particles in a silver-rich matrix as shown in Fig. 1. A eutectic structure was not observed, probably .due to the low beryllium concentration of the eutectic composition and eutectic divorcement. Within a given grain, the small globules of the primary phase were all oriented in the same direction, as indicated by examination under polarized light; the orientation varied from grain to grain. This suggested that the globules were branches of the same dendrites. If cooling was too slow, a third constituent was observed in the microstructure; because it formed around the primary beryllium-rich globules it was Fig. 1—Ag-Be alloy, 18.6 at. pct Ag, as-cast. Bright field illumination. Etched with an aqueous solution of NH,OH and H2O2. X500. Reduced approximately 21 pct for reproduction. probably the 6 compound. A thin ring around an ingot often contained this constituent. When this compound was present in large quantities, or the silver segregated so that large regions occurred with the beryllium-rich globules in contact, sections from the ingot were brittle. When the compound was initially absent, it was possible to carry out reductions in thickness of 50 pct by cold rolling with only limited edge cracking; failure did not occur until reductions of 80 pct. A typical cross section after cold rolling is shown in Fig. 2. After simple bend tests, microcracks were found; these apparently were difficult to propagate in the two-phase structure, as the specimens continued to behave in a ductile manner after the cracks appeared. Similar cracks would probably be closed during rolling. It is apparent in Fig. 2 however, that the primary beryllium particles undergo extensive plastic deformation. Hardness values of the alloys indicated that some work-hardening occurred during cold working. Fig. 2—Ag-Be alloy, 18.6 at. pct Ag, reduced 83 pct in thickness by cold rolling. Bright field illumination. Etched with an aqueous solution of NH,OH and H2O2. X500. Reduced approximately 21 pct for reproduction.

Jan 1, 1961

By Louis Moyd

In the preparation of illustrations to accompany reports of investigations concerning particle shapes of various natural and manufactured materials proposed for use as he aggretates in concrete structures, it was found that stereoscopic views of such materials presented the information much more effectively than the usual two-dimensional photographs. With the whole-hearted cooperation of the Photographic Section, a technique was developed in the petro-graphic laboratory of the Concrete Research Division, U.S. Corps of Engineers, at Clinton, Miss., for simple and rapid preparation of paired stereoscopic photographs and micrographs. The method requires only equipment which is usually part of the general stock of any laboratory, and it is adaptable for all purposes in which three-dimensional views would be found superior to ordinary photographs. Stereoscopic Photographs Where the subject or subjects to be photographed are small but not of microscopic size, an ordinary camera having a ground-glass focusing screen is set up vertically over the field. The material to be photographed is placed on a card, the surface of which is suitable as a background. The card is mounted so that it can be tilted about 5' above and below the horizontal plane, on an axis that coincides with the north-south diameter of the viewing screen. A simple way of achieving this is to mount the card on an object having a convex lower surface. In our laboratory, a watch-glass has been used, with plasticene as the mounting medium. The convex surface should be mounted on a support having a round opening on top and a flat bottom. A roll of tape, a petri dish, a beaker, or any other piece of equipment having the proper shape to give stability to the setup will be satisfactory. The arrangement of the required equipment is shown in Fig 1. For the best results, the subject to be photographed should be mounted in the plane of the axis of rotation. To achieve this effect, the depth of the mass of plasticene between the background and the watch-glass is varied so that when the watch-glass is tilted back and forth on the axis, the subject to be photographed does not appear to move back and forth across the viewing screen. A permanent piece of equipment, embodying an adjustable vertical screw, with lock-nuts, could be made for this purpose. The subject may be illuminated in any manner desired. It was found that the presence of shadows intensifies the effect of depth. In taking the photographs, the concave surface is mounted so that one side of the background card is about 5' below the horizontal, while the axis remains in the horizontal plane. The subject is focused carefully on the ground glass and a picture is taken. The card is then tilted so that the opposite side is about 5' below the horizontal, while the axis still remains in the horizontal plane. The subject is again put in focus and another picture is taken. After both pictures are developed and printed, they are placed side by side in the same orientation and examined with a stereoscopic viewer. If depressions appear where there ought

Jan 1, 1950

By J. E. Lawver, R. R. Beebe, J. L. Wright

This paper describes a separation coefficient Ks useful as a "measure of goodness" to be used in factorial and response surface methodology. The use and limitations of the separation coefficient is discussed, and a computer program for calculating the coefficient is presented (in Fortran). The application of the coefficient is illustrated in terms of electro-dynamic separation of Mesabi semitaconites. Present Mesabi wash ores and gravity concentrates with an iron to silica ratio of only 5 or 6 to 1 are no longer readily salable, for the steel industry now demands concentrates with an iron to silica ratio of at least 10 to 1 and a structure comparable to pellets. THE ELECTRODYNAMIC-FLOTATION PROCESS Wash ores and gravity concentrates consist largely of hematite, goethite, and quartz. Several methods of beneficiation are being tested at the University of Minnesota Mines Experiment Station with a view to improving the salability of these materials. A process that looks particularly promising from an economic view is the combination electrodynamic-flotation process shown in Fig. 1. This process is designed to upgrade gravity concentrates to a 5% silica content and to provide fines — from the flotation circuit —to permit agglomeration. Although electrodynamic concentration of specularite is an established and well-understood process, the electrodynamic concentration of Mesabi goethite-hematite gravity concentrates presents interesting and enigmatic problems. The gravity concentrates are by no means assemblages of clean, free mineral particles. Instead, the concentrates to be retreated consist of a great variety of middlings. More or less complete liberation would require grinding to minus 325 mesh, at which size only flotation could be expected to function, and even then grades and especially recoveries would not be satisfactory. A close examination of the gravity concentrates shows that grinding to 100% minus 48 mesh will produce a product which is approximately 70 weight % plus 325 mesh (see Fig. 1). The remaining 30 weight % can be deslimed and floated by conventional methods, but the resulting iron concentrate is

Jan 1, 1964

By W. Rostoker

A STUDY of the titanium-oxygen system' involved an associated series of measurements of the lattice parameters of the a and TiO phases. The results permit some interesting deductions which are herein reported. A comprehensive survey of the physical PI-operties of the phases in this alloy system has been made by Ehrlich.2 However, only impure titanium was available at that time, so that some revision of his measurements is to be expected. The lattice parameters were calculated from the high angle lines of Debye-Scherrer patterns taken in a 14 cm camera and using filtered CuKa radiation. The specimens were prepared largely by crushing and screening of lump samples which had been quenched from elevated temperatures. Only in the case of low oxygen contents was it necessary to resort to filing and annealing. The results of the lattice parameter studies are graphically presented in Figs. 1 and 2. It will be seen that oxygen produces a pronounced distortion of the c parameter of the a phase (hexagonal close-packed). The trend is in general agreement with Ehrlich's work, although the divergence of actual parameter values strongly suggests that his titanium was very impure. It will be noted that the a phase of titanium can tolerate the unusually high saturation solubility of about 34 atomic pct 0. By virtue of this unique effect, it is possible to make a calculation of the effective atomic diameter of oxygen when dissolved in a lattice with metallic bonding. This has not been possible before. Ehrlich's2 density measurements demonstrated that oxygen occupies interstitial positions in the a lattice and the trend of the lattice parameters would certainly support this. In a hexagonal close-packed unit cell the largest interstitial positions lie at (2/3, 1/3, 1/4) and (2/3, 1/3, 3/4). Accordingly, if both of these positions were occupied, the ratio of titanium to oxygen would be 1:1. The extrapolated c parameter may be taken as between 4.93 and 4.99?. The a parameter appears to reach a constant value of 2.955? at low oxygen contents. The distance of the center of a titanium atom site from the [vc2/16+a2/3-1.448] Then the atomic diameter of the oxygen atom is represented by the function: where the radius of the titanium atom is 1.448A,

Jan 1, 1953

By R. Rocca, M. B. Bever

THE adiabatic elastic deformation of a body is accompanied by a change in temperature. This phenomenon is known as the thermoelastic effect. Under adiabatic conditions the temperature of a metal bar is decreased by an elastic elongation and is increased by an elastic compression. All materials which elongate on heating behave in this manner. The sign of the thermoelastic temperature change is reversed for the few materials which have a negative coefficient of thermal expansion. The following equation for the thermoelastic effect can be derived from fundamental thermody-namic theorems, as shown in the Appendix: dT8 =-a1/cs T dss [1] Cs In this equation, T is the absolute temperature, S is the entropy, a, is the coefficient of linear thermal expansion, cs' is the heat capacity per unit volume at constant stress and s is the stress (positive in tension). Eq 1 can be applied to small, but finite changes in stress in the following form: ?Ts =- a1/cs T?ss [2] The sign of the temperature change AT is opposite to that of the change in stress s for materials which have a positive coefficient of thermal expansion. Eq 2 has been verified for many different materials and stresses at room temperature. No previous publication appears to have been devoted to an in- vestigation of the thermoelastic effect over a range of temperatures. Review of Literature Lord Kelvin (W. Thomson) presented a general theory of the thermoelastic effect in 1851' and later applied it to a solid, subject to an arbitrary system of stresses'. His analysis was based on a cycle of isothermal and constant-strain transformations and led to Eq 2 above. Even today, one of the clearest expositions of the thermoelastic effect is found in Lord Kelvin's article on elasticity in the Ninth Edition of the Encyclopedia Britannica (1878). R. ROCCA, Junior Member, and M. B. BEVER, Member AIME, are Research Assistant in Metallurgy and Associate Professor of Metallurgy, respectiuely, Massachusetts Institute of Technology, Cambridge, Mass. AIME New York Meeting, Feb. 1950. TP 2760 E. Discussion (2 copies) may be sent to Transactions AIME before APT. 1, 1950, and is scheduled for publication Nov. 1950. Manuscript received Oct. 15, 1949.

Jan 1, 1951

By M. L. Rudee, R. A. Huggins

Samples of iron containing nitrogen or carbon have been given treatments similar to those used in cold-work peak (CWP) measurements and examined by transmission electron microscopy. It was observed that the unusual and nonreproducible behavior of the carbon CWP can be explained by a strong tendency for carbon to form grain boundary precipitates at temperatures below those used for CWP measurements. These precipitates dissolved at the temperatures used in the CWP measurements. There was no evidence for nitrogen precipitation at grain boundaries. There was no indication of precipitation along dislocations in either carburized or nitrided samples given treatments similar to those of CWP measurements. Although it is possible that subelectron-microscopic clustering had occurred, this observation supports the theories of the CWP that are based on continuous atmospheres rather than on individual precipitates. In an earlier paper,' the present authors developed a new distribution function to predict the occupation of sites for interstitial impurity atoms around a dislocation. When this distribution was applied to the case of carbon and nitrogen in iron, it predicted that, if the temperature dependence of the concentration of solute atoms in the matrix was controlled by the presence of equilibrium carbide or nitride precipitates, the tendency for nitrogen to segregate to dislocations would be greater than that for carbon even though their binding energies to dislocations are identical. The cold-work internal-friction peak (CWP) is considered by most authors to be produced by the interaction of interstitial impurities with dislocations. Many investigators have studied the CWP in iron containing carbon and nitrogen and have observed a significant difference between its behavior in the two cases. In this paper a series of experiments will be reported that were initiated to determine whether the application of the new distribution function would explain the observed differences between the carbon and nitrogen CWP. Although it was found that the distribution function, pev se, did not explain the differences, the differences became clear, and some insight into the mechanism of the CWP was realized. Before reporting the present experiments, the literature pertaining to the differences between the carbon and nitrogen CWP in iron and the various mechanisms proposed for the CWP will be reviewed. LITERATURE REVIEW Snoek2 first observed the CWP in iron specimens containing nitrogen, but also reported a weak and unreliable peak in carburized samples. Later, Ke3 established that the CWP height was proportional to the degree of deformation. The presence of nitrogen alone would produce a peak of the same size as found in a sample containing both nitrogen and carbon, and KG concluded that the CWP was caused by nitrogen. In a discussion of G's paper it was reported that Dijkstra had investigated the CWP in samples that contained only carbon. He found it to be much smaller than the nitrogen peak and "unstable". KG et al.4 charged specimens of iron with both carbon and nitrogen. They observed that the carbon CWP was much smaller than that observed in nitrided samples, but that aging at 300°C caused the carbon peak to increase. A similar treatment produced no change in a nitrogen peak. Annealing at higher temperatures caused the height of the CWP in both the nitrogen and carbon samples to decrease. This behavior was also observed by Kamber et al. 5 who found that the activation energy for the annealing of the CWP was identical with the activation energy for the self-diffusion of iron. They concluded that the annihilation of dislocations by climb caused the reduction in the CWP height. Kamber et al. studied the "unstable" carbon peak in detail. They measured both the Snoek and CWP during various aging treatments. In carburized samples, aging at 100°C caused the Snoek peak to disappear, although the CWP peak remained small. However, a subsequent treatment for 5 hr at 240°C caused the CWP to reach a maximum. They proposed that an additional location for the carbon, other than whatever site produced the CWP, is present. In nitrided samples the CWP was completely developed as soon as a measurement was made; additional sites are not present. No explanation of either the additional site or the difference in the behavior of carbon and nitrogen was offered. petarra5 performed a systematic study of the effect of composition on the CWP. Using three kinds of "pure" iron, he showed that there was a residual CWP when the carbon and nitrogen concentrations had been reduced to less than that detectable by Snoek-peak measurements. He observed the same general annealing behavior and composition dependence as previous investigators, with the following exceptions. On first measuring the carbon CWP, it was found to be identical with the residual peak, and essentially independent of the carbon content. If the CWP was measured a second time in the same sample, it increased in size, but was still only about one-fourth the size of a CWP in a sample of the same iron nitrided to the same composition. On the other hand, a series of annealing experiments showed that the nitrogen CWP was not al-

Jan 1, 1967

By Charles W. Merrill

IF we follow the threads of the mining problems, upon which I have touched, we find them all leading to one great fundamental desideratum. The people of this State, of this Nation, and of this world must be brought to a better understanding of the basic nature of our industry-must be made more mineral-minded. It is my belief 'that there is not a man present among this earnest gathering of those interested in the mining industry, who has not a deep-seated and heartfelt desire that the existing unprecedented welfare and prosperity of the whole mass of American people be maintained not merely through our own generation but through the generations of our children and their children. In the decades to come there can be no question of the keenness of the foreign competition which we are doomed to meet, and in this great international contest that Nation which has the best balanced program of development and that broadness of vision in its governmental direction, which recognizes the necessity of a sympathetic attitude toward the upbuilding of such a broad pro- gram will be the Nation which will maintain and pre- serve that welfare of all of its people.

Jan 1, 1929

By James Aston

A PROPER consideration of this subject is not confined to the technical channels of production and metallurgy. It concerns an industry, and should cover economic aspects which are of material importance in any program of development. The discussion may logically be treated under three subdivisions, as follows: (1) manufacture, (2) characteristics related to quality of material; (3) adaptability and exploitation of product. MANUFACTURE OF WROUGHT IRON The manufacture of wrought iron is the most ancient art of the ferrous metal industry. The eighty years or less of existence of processes identified with our modern "Age of Steel" is a relatively brief interval compared with the several thousand years associated with the production of wrought iron by man. From the primitive early methods of production, manufacture for many centuries followed the line of direct reduction. There were developments as experience was gained through the years; but man's needs for a strong, ductile, forgeable product were met by reducing the ore to metallic iron in a single-stage operation. Following the development several centuries ago of what has become our modern blast-furnace operation, manufacture of wrought iron was gradually transformed into a two-stage method of first producing cast iron and then refining this to the desired degree of forgeability; the forerunner in principle of today's scheme of manufacture of steel. The product retained the essential characteristics of highly refined base metal with iron-silicate slag incorporation, which were associated with the material resulting from direct reduction methods. Cort's invention of the puddling process in 1784 is a landmark in wrought-iron manufacture. It consisted essentially in adapting a coal-fired reverberatory furnace to the refining operation; thus lifting the industry out of the slough of

Jan 1, 1935

By Joseph Fry, Ralph H. Espach

In the spring of 1943, when it was evident that the Tensleep bandstone in the Elk Basin Field, Wyoming and Montana, held a large reserve of petroleum, Bureau of Mines engineers obtained samples of oil from the bottom of nine wells and analyzed them for such physical characteristics as the volumes. of gas in solution. saturation pressures or bubble points, shrinkage in volume caused by the release of gas from solution, expansion of the oil with decrease in pressure, and other related properties. The composition of the gas in solution in the oil was studied. The pressures and temperatures existing in the reservoir and the productivity characteristics of the oil wells were determined. The data obtained indicate that the oil in the Tensleep Reservoir of the Elk Basin Field has unusually varying physiral characteristics, such as a saturation pressure of 1,250 psia and 490 cu ft of gas in solultion in a barrel of oil at the crest of the structure and a saturation pressure of 530 psia and 134 cu ft of gas in solution in a barrel of oil low on the flanks. The hydrogen sulfide content of the gas in solution in the oil varies from 18 per cent for oil on the crest to 5 per cent for oil low on the flanks of the structure. Of even greater significance is the fact that these and other variable characteristics of the reservoir oil are related to the position of the oil in the structure. Many geologists and petroleum engineers have considered that all the oil in a petroleum reservoir has rather uniform physical characteristics and that equilibrium conditions prevailed in all underground accumulations of oil and gas; that such is not always so is borne out by the results of the study by the writers. INTRODUCTION The Rocky Mountain region is one in which may be found striking examples of the unusual in oil and gas accumulations, as is evident from the following: The high helium content (7.6 per cent) of the gas in the Ouray-Leadville limestone sequence in the Rattlesnake Field, New Mexico, and gases of similar helium content in other fields; 50" to 55' API gravity distillate in solution in carbon dioxide gas and recoverable through retrograde condensation, in the North McCallum Field, Colorado; the occurrence of gas, oil, or both in closely related structures contrary to the usual concepts of gravimetric segregation: the accumulation of gas and/or oil in structures closely related to other structures that apparently are more favorable but do not contain oil or gas accumulations; the high hydrogen sulfide content (as high as 42 per cent) of the gas associated with oil in some fields in the Big Horn Basin, Wyoming; and the wide range of fluid chararteristics found in the Elk Basin reservoir. Elk Basin, an interesting old oil field that has been producing oil from the Frontier formation since 1915, is situated in a highly eroded basin resulting from the erosion of the crest of an anticline and some of the underlying softer shales. The field came back into national prominence during 1943 when it became known that it was the largest single reserve of new oil discovered in the United States that year. The Tensleep sandstone was found to contain oil in November. 1942, when a well drilled to a depth of 4,538 ft (44 ft into the Tensleep sandstone) flowed oil at the rate of 2,500 B/D. By the end of 1949, 137 oil-producing wells and five dry holes had been drilled, and approximately 32 million bbl of oil had been produced. Approximately 6,000 acres may be considered productive of oil in the Tensleep Reservoir, and estimates of the oil that will be produced average 200 million bbl. The Tensleep Reservoir has further interest because it ha-greater closure than any oil field in the Rocky Mountain region; the closure of the Elk Basin anticline is variously estimated at 5.000 to 10,000 ft. of which the top 2.00 ft of the structure contained oil. SUBSURFACE OIL SAMPLING Fig. 1 is a structural map of the Elk Basin Tensleep Reservoir, on which the nine wells used in this study and the numbers correvponding to the well designations hereafter referred to are shown. Wells 1. 2, 3, 4, and 8 were tested and sampled during October and November. 1943. and Wells 5, 6. 7, and 9 during June and July, 1944. An electromagnetic type sampler developed by the Bureau of Mines and described by Grandone and Cook' was used in obtaining the subsurface oil samples. As the wells were tubed nearly to bottom, the sampler was run as far as possible in the tubing hut never below the top perforations. The following procedure was used in testing and sampling the wells: A well was shut in for at least three days, after

Jan 1, 1951