Search Documents

By H. L. James

THIS paper presents the results and analysis of field trials of various magnetic instruments over anomalies ranging from 20 to 5000 gammas of vertical intensity. The following instruments were used: Askania vertical magnetometer, Wolfson vertical magnetometer (model M-I), Hotchkiss Superdips (used both parallel to and normal to the magnetic meridian, with several settings of the "sigma" angle), Lake Superior dip needle, and the dipping circle for measurements of inclination. The change in inclination over the measured anomalies ranged up to 4°; this caused pronounced changes in sensitivity of the Hotchkiss Superdip oriented parallel to the magnetic meridian. The variable sensitivity not only gives apparent displacement of crests of anomalies, particularly at high sensitivities, but also makes the data difficult or impossible to use in preparation of iso-anomaly maps. This weakness in field performance of the Superdip is shown to be eliminated by orienting the instrument normal to the magnetic meridian and measuring vertical intensity only, which in the latitude of upper Michigan is equal to 97 pct of the total intensity. The dip needle is seen to be relatively ineffectual for location of anomalies of less than 400 gammas.

Jan 1, 1947

By Daniel L. Murphy

The iron ore province of Quebec and Baffin Island trends from the southern shore of Baffin Island northeasterly through the Labrador Trough to Matonipi Lake, approximately 185 miles northwest of Seven Islands, but future geologic field studies will very likely extend the limits of the province to include the ferruginous and associated rocks of the Lake Mistassini area. Recent improvements in the beneficiation of low-grade iron ore have stimulated widespread exploration for deposits amenable to concentration, particularly along the southwest extension of the Trough. GENERAL LITHOLOGY Pleistocene and recent deposits of clay, sand, gravel and erratic boulders cover roughly 60% of the land surface. All of the bedrock is of Precambrian age (Table I). Paragneisses and paraschists together with metasedimentary iron-formation, marble and quartzite are abundant and, for the most part, appear to be metamorphic equivalents of the relatively unmetamorphosed rocks of the Labrador Trough to the north beyond the "Grenville Front." Bodies of amphibolite are widely scattered. A large portion of the metamorphic rock shows some degree of permeation by granite material as well as alteration by hydrothermal solutions. The youngest bedrock consists of a complex containing slightly altered ultramafic to monozonitic intrusives.

Jan 9, 1962

By V. C. Allison

Large-scale testing of the explosibility of coal dust as conducted by the Bureau of Mines in its Experimental Mine involves a large initial investment, and a high charge for maintenance and conduct of the test; in addition the work is necessarily slow because of the time required for the preparntion of the tests and the cleaning and repairing of the mine after each test. These tests have been made along practical mining lines that admit of a range of mixtures of dust varying from 5 to 10 per cent. and with gas as low as 0.5 per cent. increments. Because of the time and expense involved, efforts have been made to devise a type of gallery for laboratory use in which the results obtained in the Experimental Mine may be correlated as an aid in a study of dusts, the explosibility of which might be approximately determined quickly and at a minimum of expense. The explosibility of coal dust has been studied by a number of European investors, using small laboratory devices; among these may be mentioned the experiments conducted by Galloway, Vital, Hall and Clark, Abel, Mallard and Chatelier, Thorpe, Bedson and Widdas, Engler, Holwartz and Meyer, and Taffanel, results of whose experiments have becn reviewed by the Bureau of Mines.' The Bureau has conducted many tests with the Frazer-Cle1ncnt5 apparattus, which gives the pressures set up when the dust cloud within is ignited with a platinum coil or tube, heated to different temperatures, but for these tests the sample must be especially prepared as to size (200 mesh) and must be dry. Need for a Dust-testing Apparatus An attempt has been made to design an apparatus that may be used for checking and correlating the expcrimental tests. The first design was a wooden gallery, 8 by 10 in., inside cross section, and 12 ft. long, and having a number of strips along each side for creation of turbulence. The wooden gallery did not get beyond its period of calibration; it mas difficult to make the gallery sufficiently tight, for it was necessary that the top be removable in order that the gallery could be cleaned. In the use of the wooden gallery, however, sufficient operating data were obtained to be a guide in the design of a steel gallery having a circular cross-section. One of the features was a flap valve, at the closed end of the gallery, that would open inwardly thus preventing a reduced pressure within, caused by the cooling of the gases of combustion, and the explosions propagated much better than when the valve was not used; another feature was the determining of the best method for getting a cloud of dust simultaneously in all parts of the gallery, which was accomplished by the use of the concussion wave of a small quantity of powder or by the use of compressed air.

Jan 1, 1927

By G. W. Ostroot, S. Shryock

Cementing deep, high-temperature oil wells where static temperatures range from 350 to 400F has become routine in the part decade. In the United States there were 271 wells drilled deeper than 15,000 ft during 1963. Many of these wells had static temperatures higher than 400F. Bottom-hole static temperatures near 700F are now realities in the geother-mal (steam producing) wells of California's Salton Sea area. The detailed planning initiated prior to drilling the wells is discussed together with the methods, materials and equipment used in solving the cementing problems which are encountered. Data are also presented that lead to development of cementing compositions that provide adequate thickening time, do not retrogress in strength, and maintain low permeability under these extreme temperature conditions. Field data include the cementing programs used on eight relatively trouble-free geothermal steam wells in the Salton Sea area. INTRODUCTION Not too many years ago cementing oil wells with temperatures in the range of 300F caused considerable anxiety. In some areas of the United States it is now fairly common to cement wells having bottom-hole static temperatures in excess of 400F. We are now confronted with the problem of cementing wells with temperatures ranging from 500 to 700F. Temperatures in this order of magnitude are often found in geothermal steam wells. From where does this extreme heat emanate? There are many theories as to the source of this steam flow. The most widely held views are: (1) heat- ing of ground water fairly close to the surface by an intrusive mass of hot rock; (2) steam generation from a reservoir of metamorphic rock, normally found below 25,000 ft and not at the shallower depths of the Salton Sea reservoir; and (3) high-temperature gases (water vapor) escaping and migrating from molten or semi-molten rock (magma) at a considerable depth. Of these. No. 3 seems to be the most generally acceptable explanation. Heat from springs and fumaroles has been used for years as a means of heating and cooking; however, significant progress in harnessing the vast power of underground steam reservoirs has been relatively slow. The first large-scale attempt to use the heat generated by steam from wells was made in Italy around the beginning of the 20th century. In excess of 250,000 kw of electrical power is now being produced from holes around Larde-rello, Italy. Another very active drilling program was initiated in the volcanic area of New Zealand in 1949.' Natural steam for power projects in the United States began in the early 1920's. An early commercial steam field is located at the Geysers, approximately 75 miles north of San Francisco, an area discovered in 1847 and used for many years as a health resort. Steam originates from 15 wells that have been drilled since 1957. The present output from this project is 25,000 kw. Success of the Geysers operation has been responsible for several companies taking a careful look at the feasibility of producing steam for power generation in the Salton Sea area of Southern California's Imperial Valley. Geothermal steam activity in this latter area began in 1961 when O'Neill, Ashmun and Hilliard completed Sportsman No. 1, at that time the hottest wellbore in the world.' Since its References given at end of paver. completion seven additional wells have been successfully completed in this area. Many problems encountered in drilling steam wells had to be overcome to make the ventures successful. Formation temperatures encountered in the Salton Sea seemed to be a straight-line function (a gradient of 13F per 100 ft of depth).' This imposed severe conditions on all aspects of drilling and completion. This varied, to some extent, from gradients in the older geothermal areas. Not to be overlooked is the effect of these temperatures on casing creep or elongation by thermal expansion (Table I), because standard API flanged wellhead equipment makes no provision for this kind of performance. Floating equipment was redesigned, and changes in types of downhole equipment were made in an effort to eliminate anticipated problems. In the later completed wells, standard oil-well cementing equipment has been used. During the early development of geothermal steam wells there were some problems resulting from blowouts. However, these were eliminated in the deeper Salton Sea wells and no problems were encountered with the drilling mud. A sodium surfactant mud was used on the Sportsman No. 1 to drill from 2,690 to total depth. Nevertheless, it was necessary that a cooling system be added and the mud cooled before circulating it back into the well. The difficulty in evaluating the size of the steam area and its potential in terms of pounds of steam and years of productivity still has not been resolved. Economic complexities have also entered into the steam play in the Salton Sea. The wells at the Geysers were drilled at a cost of $15,000 to $20,-000, whereas the Salton Sea wells will cost more than $150,000. This cost differential has to some extent been accounted for because of the heavily

Jan 1, 1965

By E. D. Gardner

IN 1947 the metal-mining industry . passed through a year of readjustment; catching up on development work has caused production to suffer. Skilled labor has been short in most mining districts, notwithstanding the highest wage rate paid in the history of the industry. The trend has continued toward increased mechanization and refinements in practices and methods to increase the tons produced per man-shift. Improvements in procedures, however, have not kept pace with rising labor rates; and, in general, labor costs per ton mined have steadily increased since the war years. Prices of base metals have been the highest in a generation, but most producing companies can afford to pay the high wages. Capital expenditures have been approved for improvements to increase the output per man, both to reduce unit labor costs and to increase output. Surveys indicate a continuing

Jan 1, 1948

By J. C. Irvine

Meramec Mining Co., a joint venture by Bethlehem Steel Corp. and St. Joe Minerals Corp., is engaged in the mining, concentrating, and pelletizing of iron ore from the Pea Ridge mine near Sullivan, Mo., about 70 mi southwest of St. Louis. The orebody lies under about 1300 ft of sediments. It is tabular, about 2600 ft long and up to 600 ft thick, and lies in an approximate east-west delineation. The orebody dips about 80"s and is of unknown depth. The ore is primarily high grade magnetite with smaller zones of specular hematite. The Precambrian wall rock is rhyolite porphyry. The mine is serviced through two concrete-lined shafts, 19 ft 1 in. diam and 2500 ft deep. No. 1 shaft, equipped with an "A" type head-frame and conventional cylindrical drums, hoists men, materials, and waste rock; it is also the downcast air shaft. No. 2 shaft utilizes tower-mounted friction hoists to handle the two production skips, each with 24-ton counterweights, and a small man cage. The mine exhaust passes through this shaft. Ore is principally mined by sublevel stoping,

Jan 9, 1972

By George A. Connell

BORAX, a sodium borate and the principal sodium salt of boric acid, has been surrounded with romance and with a certain amount of mystery. Its early history is not entirely known but it has been contended that Marco Polo in his travels in the Orient introduced this material to the West during the Middle Ages. Without doubt its first source was from Central or Eastern Asia and perhaps from Tibet. The well-known fluxing properties of borax probably introduced its earliest use that of a soldering flux in the manufacture of jewelry. This use, as well as the remote location of most borate deposits, added greatly to the romance associated with the thought of borax. COMPOSITION The common element in all borates is boron but this element has never been discovered as such in any deposit, because of its great affinity for oxygen. Incidentally, this makes its manufacture extremely difficult and expensive. Elemental boron undoubtedly has many properties that make it quite valuable but the extreme cost involved in producing it from its oxidized form prevents its general use or manufacture. The common element in all borates is boron but this element has never been discovered as such in any deposit, because of its great affinity for oxygen. Incidentally, this makes its manufacture extremely difficult and expensive. Elemental boron undoubtedly has many properties that make it quite valuable but the extreme cost involved in producing it from its oxidized form prevents its general use or manufacture. The common element in all borates is boron but this element has never been discovered as such in any deposit, because of its great affinity for oxygen. Incidentally, this makes its manufacture extremely difficult and expensive. Elemental boron undoubtedly has many properties that make it quite valuable but the extreme cost involved in producing it from its oxidized form prevents its general use or manufacture of disodium tetraborate (Na2B4O7.10H2O), and, further, can be considered as the acid salt of monosodium metaborate. However, the term "acid salt" might imply that borax gives an acid reaction in solution, which is not true, since solutions of borax are decidedly alkaline, giving a pH of 9.2. Boric acid, also known as boracic acid, has the chemical formula H3BO3; it occurs in nature as the mineral sassolite. Sassolite has been

Jan 1, 1949

THE papers presented by the Institute of Metals at the Detroit meeting in September, 1926, and the New York meeting, February, 1927, will be issued soon in one volume and mailed to all members of the Institute of Metals Divi-sion of this Institute. The, annual lecture given by Cecil H. Desch will begin the volume and the discussion occurring at the sessions, as well as subsequent written discussions, will be appended to each paper. The volume will contain about 600 pages, and will be sent without charge on request to any member of the Institute. The pre-subscription price to non-members is $5.

Jan 4, 1927

By Harmon E. Keyes

Harmon E. Keyes (Chemical & Metallurgical Engineer, Eagar, Ariz.)-Chemical dissolution of chalcocite by acidic ferric sulfate is well known. Resulting elemental sulfur may be oxidized to sulfuric acid by heated ferric sulfate. Laboratory tests at Southwest Experiment Station, USBM, Tucson, generally confirmed stoichiometric relations of 1 part Cu dissolved to 1.750 parts ferric iron reduced, using CP chemicals, dried ore samples, and apparatus cleaned with potable water. Recirculation with open-drainage percolation to increase copper in leaching solvent was followed successfully when appropriate, both in laboratory and Pinto Valley pilot tests. Before 1924 attempts to produce ferric sulfate by aerating ferrous sulfate solution were known. Initial oxidation was satisfactory, but rate slowed below practicality as oxidation progressed and acidity increased. Also, due to hydrolysis of ferric sulfate, a ferric precipitate of hydroxide and basic sulfate resulted. Both laboratory and pilot plant tests gave similar results, regardless of whether CP ferrous sulfate or scrap iron cementation discard solution was used. Rapid oxidation of ferrous hydroxide by air alone is well known to analytical chemists. I demonstrated a process to produce acidic ferric sulfate solutions by precipitating ferrous hydroxide with milk of lime, aerat-

Jan 1, 1973

By Walter A. Backofen, Donald H. Avery

Intense primary and cross-slip traces were observed in easy glide on Cu: 6 pct-A1 single crystals deformed in tension. A mechanism of cooperative source operation is developed which recognizes that both the applied stress and that resolved from dislocation arrays contribute to the stress on a source. By considering the stress from arrays, the activation of secondary systems in easy glide and the difference in appearance of slip markings on pure and solid-solution crystals are explained. Furthermore the cross-slip system is predicted to be second favored during easy glide for a large range of orientations. FROM many studies of easy glide in fcc metal crystals, a pattern of observations has developed which still requires full explanation. In pure copper, aluminum, and silver, the easy-glide, slip traces are fine and uniform with steps 50 to 100A on the primary* system.1-4 Yet it has not been at all clear why slip in the pure materials should occur in this way. On the contrary, one might expect, with simple slip and a low hardening rate, that the weakest sources on the primary system would operate extensively to produce strong slip traces. In a brass, however, intense slip steps up to 0.5 are found on both primary and cross-slip system4,6-9 seeger10 has pointed out that in a material of low stacking-fault energy such as a brass, extensive easy-glide cross-slip could not be thermally activated, but rather must originate on the cross-slip plane. In further explanation, the wilsdorfs4 and seeger10 noted that only the cross-slip system would not harden differently than the primary, whatever the latent hardening tendencies of other systems; therefore, in brass, which exhibits high latent hardening, the cross-slip is the only secondary system which could be expected to operate extensively, once it became active. The explanation of how the cross-slip system, on which the applied stress is low, becomes activated has been related, in a nonspecific way, to pileups by Hirsch11 and Honeycombe.l2 In the work to be described, deformation traces on solid-solution Cu: 6 pct A1 single crvstals were studied with conventional light microscopy and a mechanism proposed to explain both the observed activation of secondary systems in easy glide and the difference in appearance of slip markings on pure and solid-solution crystals. EXPERIMENTAL In preparing the Cu-A1 single crystals, rectangular bars approximately 0.4 in. by 0.4 in. by 6 in. were first machined from ingots made by vacuum melting copper of 99.999 pct and aluminum of 99.99 pct purity. They were then packed in powdered graphite and the crystals grown in a modified Bridgman apparatus at a rate of 5 mm per hr under an atmosphere of purified nitrogen. Crystal perfection as indicated by Laue back-reflection spots was good except for the last inch to freeze, which was discarded. Orientations so determined are shown in Fig. 1. Tensile specimens with a reduced gage section were obtained by masking the ends with electrical tape and chemically polishing in a solution of 20 pct HNO3, 24 pct HAc, 52 pct H3PO4, 2 pct Hcl, and 2 pct H20 at room temperature.13 Finally, the specimens were electropolished in a 30 pct ortho-phosphoric acid bath at 12 v. Tensile deformation was performed in an Instron testing machine at a strain rate of approximately 1 pct per min. During easy glide, extensive cross-slip was observed with all crystals, in spite of the low Schmid factor on this system, and in no case was any other secondary trace encountered. A certain sequence of slip-line development was associated with the extension. At yielding, intense primary traces passing completely through the crystal developed at some point on the gage section, generally near the grips; weak cross-slip traces also appeared, extending from the primary traces into the adjacent undeformed crystal, Fig. 2. Further extension led to primary traces adjacent to the first-formed and connecting with those of the cross-

Jan 1, 1963

By J. V. W. REYNDERS

THE principal manganese deposit of Russia, I one of the four principal sources of the world's supply, lies on the southern slope of the Caucasus Mountains, in what is now the Republic of Georgia, district of Sharopan. Tchiatouri, the principal town, is midway between Tiflis, the capital of Georgia, and Poti, the shipping port on the Black Sea, about 130 " miles distant. The deposit can be most easily visualized by thinking of a nearly horizontal coal seam about 6 ft. thick, outcropping on the slopes about 600 ft. above the Kvirila River. One of the accompanying illustrations shows the river, which nearly bi- sects the district, of approximately 50 sq. miles in area, and with its tributary streams makes the topography rugged, while in the background are the snow-capped peaks of the Caucasus range. Another of the illustrations gives a closer view of the outcrop. The roof and floor of the deposit are good, so the methods of working are quite similar to working a coal seam, especially as most of the mineral is soft enough to be mined with a pick. Little machinery is used, except small cars for underground transportation.

Jan 1, 1926

By J. C. Purcupile, R. L. Morris

Present methods of roof support require that first a hole must be drilled, and then a toggle belt or grouted resin bolt be set. Automating this system is very difficult. Therefore, we decided to develop a system which would insert pins into the roof in one step. We think that this type of system can be automated much easier. It would then speed up the roof bolting operation and eliminate the need for a man to work under unsupported roof, making roof bolting a much safer job. There are two ways that a pin can be inserted in a mine roof without drilling a hole. It can either be pushed in, using a very high, constant axial force; or it can be hammered in like a nail. The former method involves very high compressive stresses in the pin, and requires complicated machinery to prevent buckling. Since hammering the pin does not require high axial forces buckling is not as likely. Also, experiments have shown that there are no problems associated with getting the pin to go in straight. We chose to develop the second method. While investigating methods for hammering a pin into a mine roof, we learned that piles were being driven 10 times faster than by conventional methods with a method called "orboresonance." We decided to turn the pile driver upside down, and drive pins up into the mine roof. Sonic Pin Setting Machine The machine consists of a steel bar supported at the nodal points of its first mode of transverse vibration (Fig. 1). A mechanical oscillator, driven by a hydraulic motor, is attached to one end of the bar. This provides the forcing function for the vibrations in the bar. The hydraulic power is supplied by a portable unit. When the forcing function is near the natural frequency of the bar, large amplitudes of vibration occur and require little power input. An anvil is attached to the bar at a point of maximum deflection, providing a means for striking the pin. Since the bar is being driven near its natural frequency, it takes little energy to accelerate the bar back and forth between each hit. This means that most of the power being put into the bar is going into driving the pin. This is unlike conventional pile drivers which use most of their power to accelerate the hammer back and forth between hits. The resonant frequency of the bar we used is about 250 Hz, which is in the audible range, hence the term "sonic pin setting machine." The system benefits are: (1) elimination of the two-step drilling and pin-setting roof bolt operation, (2) increased speed, (3) more intimate contact between the formation and bolts, (4) less expensive roof bolts, (5) higher integrity, (6) potential for automatic operation. Modifications During the months from Oct. to Dec. 12, 1974, under U.S. Bureau of Mines grant No. 00144104, "Projects on Coal Extraction," six members of the senior class at Carnegie Mellon University designed and built the experimental machine. They drove three pins into the Safety Research coal mine at Bruceton, Pa., and determined that the project was worth continuing. In January 1975 we began making modifications and repairs in preparation for a more extensive program of testing at Bruceton. The major items were: 1) Design and build a collapsible pin guide to keep the pin parallel with the line of travel of the lift table. 2) Move the anvil to the center of the bar. 3) Refinish the nodal holes and install new node pins and bushings. 4) Realign the bar in its frame. 5) Install a relief valve on the lift unit to control the upward force. The upward force that we exert on the pin is relatively small, so there is no tendency for it to buckle. This means that all we need to do is hold the pin straight during its initial penetration. This allows the bushing to travel up and down in a straight line. At the beginning of penetration, the bushing

Jan 1, 1977

Organization Place Date 1917 American Electro-Chemical Society Detroit; Mich. May 2-5 American Waterworks Association Richmond, Va. May 7-11 American Institute of Electrical Engineers New York City May 18 America' Society of, Mechanical Engineers Cincinnati, Ohio May 22-25 American Iron and Steel Institute New York City May 25-26 ' Interstate Oil Mill Superintendents Association. Augusta, Ga. May (last wk.) Electric Power Club Hot Springs, Va. June 11-14 Society for the Promotion of Engineering Education .... Evansville, Ind. June 19-22. American Institute of Electrical Engineers Hot Springs, Va. June 25 American Society for Testing Materials Atlantic City, N. J. June 26-30

Jan 5, 1917

By Bailey Willis, George Otis Smith

I. Summary of General Features. Location.—The Clealum iron-ore deposits occur on Clealum river, a tributary of the Yakima river; in the eastern spurs of the Cascade range, Washington.† Mount Stuart, 9470 feet in altitude, is a dominant peak of the district, which will therefore be referred to as the Mount Stuart district. By way of the valley and cañon of the Clealum, the ores are 18 miles from Roslyn, the colliery-town, which is reached by a short branch from the Northern Pacific Railroad. Where they occur the valley has an elevation of 2900 to 8000 feet above sea; that of the end of the branch railroad at Ronald is 2345 feet. The grade of the valley from near Ronald to the junction of the Clealum and Salmon Lasac rivers, 144 miles, is 20 feet per mile; thence to the iron-ores it is 130 feet per mile, through a cañon 241/2 miles long. Abreast of the deposits the western wall of the valley is formed by precipices of sandstone; the eastern slope is comparatively gentle, being cut in easily eroded

Jan 1, 1901

Edward A. UehlinG, New York City (communication to the Secretary*):—Mr. Baker's paper is one that brings up a subject of great importance, and if full statistics could be collectecl of the number of furnace-linings ruined by reason of bad distribution by skip-hoists, it would be found an astonishing array. Unfortunately a universal remedy has not yet been found. The fact that Mr. Baker has apparently succeeded in overcoming the trouble at Sydney, is no guarantee that the same remedy applied at another plant, where very different or even slightly different conditions prevail, mould cure the trouble. That it requires but a slight continuous difference of penetrability in the column of the descending stock of one section, over another, to produce channeling, is clearly demonstrated by Mr. Baker's experiments, by which he reversed the channeling from front to rear instead of remedying the trouble. Every change in the physical make-up of the charge necessarily requires a specific adjustment; even supposing this feasible, the regular working of the furnace is by no means assured, because with the high pressures now customary, the tendency of the ascending gases to plow their way through in a direct course, prevails, and having once opened up a passage, they will persist and cause trouble. Homogeneous filling-, hard driving and regularity of working are incompatible. The higher the furnace, the greater the

Jan 1, 1905

By E. T. Turkdogan, L. E. Leake

A number of measurements have been made on the vapor pressure of pure iron at 1600°C. Experiments were carried out by the transportation method in which a sample of iron is exposed in a furnace to a stream of pure argon, metered at a predetermined flow rate for a specified period of time. The vapor pressure was obtained from the weight loss of the sample. A detailed diagram of the apparatus used for the experiments is given in Fig. 1. It consisted of a horizontal molybdenum-wire-wound furnace fitted with a recrystallized alumina tube 1 1/8 in. internal diam. The boats, 1 by 3/16 by 1/8 in., were fired in argon at 1600°C to constant weight before use. After this treatment, subsequent heating of the boats to 1600°C gave little or no further change in weight, e.g. ±0.05 mg in 24 hr. The furnace and reaction tube were separately fed with argon from two independent flowmeters. These were connected to a common supply source via an argon purification furnace containing metallic titanium sponge at 700°C, and an anhydrone drying-tower. A rotary displacement-type meter was included in the gas train to provide a direct means of measuring the total volume of gas passed through the reaction tube. The material used was vacuum melted high-purity iron in the form of wire 2mm in diam. The following impurities were present in the iron: 0.008 pct C, 0.002 pct Si, 0.005 pct Mn, 0.008 pct S, 0.001 pct P, 0.01 pct Ni, 0.001 pct Cr, 0.006 pct Cu, and 0.001 pct Al. Samples consisting of three small pieces of this wire were laid end to end in a recrystallized alumina-combustion boat, and were separated by small fragments of alumina. The wire samples were then melted in argon to form spherical beads 2 to 3 mm in diam. After weighing, the boat with its contents was placed on the boat carrier and introduced into the cool end of the reaction tube. The entire furnace system was then flushed with argon for 30 min. At the end of this period, the flow of argon to both furnace and reaction tubes was adjusted to the desired level; then the boat was slid rapidly into the hot-zone of the reaction tube. After a known volume of gas had passed through the reaction tube, the boat was withdrawn quickly to the cool end of the furnace. When quite cool, the boat was removed from the fur-mace and placed in a desiccator for subsequent re-weighing. The semi-micro balance used in these experiments had a sensitivity of 0.005 mg. The above procedure was repeated at several flow rates within the range of 25 to 300 ml per min. The flow of argon in the annular space between the two tubes was at a rate of 300 ml per min in all experiments. During all the experiments the furnace temperature was maintained at 1600° ± 5°C by means of a temperature controller. The temperature of the reaction zone was measured with a Tinsley high precision disappearing filament pyrometer which was initially calibrated against a Pt-13 pct Rh/Pt thermocouple; the errors due to temperature measurements were within * 5°C. RESULTS Assuming that the iron vapor is in the monatomic state, the vapor pressure can be calculated from the weight loss of the sample and the volume of the carrier gas. The results obtained are plotted in Fig. 2 against the rate of flow of argon through the chamber containing liquid iron beads. At low flow rates, the thermal diffusion of iron gives an apparent high vapor pressure, but at high gas flow rates, the carrier gas is not saturated with the vapor, and therefore, low vapor-pressure values are obtained. This is now a well-known phenomenon. There is a distinct inflexion of the curve at about 120 to 160 ml per min rate of argon flow and the vapor pressure of iron within this

Jan 1, 1961

By Charles E. Hall

The Crimora mine, operated by the American Manganese Company, Limited, is located 21/2 miles east of Crimora station, 011 the Shenandoah Valley railroad, in Augusta county, Virginia. It is situated in a basin at the western base of the range of mountains which flanks the Shenandoah Valley on the east. This range is composed of the Potsdam sandstone (No. I. of the Pennsylvania survey), and extends in a northeasterly-southwesterly direction the entire length of the valley. The general dip of the measures is westward. The massive sandstone of the mountain is geologically overlaid with shales or slates, which belong to the Potsdam, or lie between it and the Lower Silurian limestone. Throughout this region these shales are decomposed, and form more or less extensive clay deposits, which are found along the base of the range and often underlie a considerable area to the westward of the abrupt slope of the range. Sand and fragments of quartzite occur in considerable quantities on the surface, and often conceal the true character of the underlying formation. The area containing this ore-deposit extends northeast and south-

Jan 1, 1892

By James A. Todd

Use of AN-FO in underground operations has greatly reduced the cost of primary explosives. AN-FO is also less sensitive than conventional dynamites, and when properly used, is safer. Maximum safety in the use of AN-FO, however, requires an understanding of potential hazards from toxic fumes as well as static electricity developed in pneumatic loading. Safe limits and guides have been established to permit most operations to pneumatically load holes that are bottom primed with electric blasting caps, but the toxic fume hazard is less widely understood. During 1959-1960 Du Pont cooperated with the U.S. Bureau of Mines to study the toxic fumes produced by prilled ammonium nitrate-NO. 2 fuel oil mixtures. The conclusions from this work were that oxygen balanced AN-FO, when thoroughly mixed, well primed and well confined in dry holes, produces no greater amounts of toxic fumes than conventional dynamites rated Class I by the Institute of Makers of Explosives. The study also showed, however, that any deviation from these guides tends to increase significantly the quantity of toxic fumes produced. This work was reported by the Bureau of International Symposium on Mining Research at Rolla, Mo., in February 1961.'

Jan 4, 1963

By Hugh J. Leach, J. C. Van de Water

In open pit mining, as in other industries, it has I become necessary to improve operating efficiency in order to combat higher labor and supply costs. Moreover, orebodies are becoming leaner, pits are getting deeper, stripping ratios are increasing, and hauls are getting longer. There has been a steady increase in size, speed of operation, and reliability of the various machines involved in breaking, loading, and hauling ore. Changes have seldom been radical but are rather the result of steady improvement. Drilling: Notable advances have been made in the use of rotary drills and air powered percussion drills for blasthole drilling. Several hundred of these machines are now in use as replacements for churn drills in softer rocks such as limestone and shale. Their application to hard rocks such as iron ore and taconite is under current investigation, but in the Lake Superior iron mining district, open pit blast-hole drilling in ore has been accomplished almost exclusively by standard churn drilling. The only recent advance has been the use of larger machines drilling 9-in. holes. This has increased drilling speed somewhat and allowed wider hole spacing, with consequent cost reduction.

Feb 1, 1956

By L. H. Ketchum, T. L. Theis, W. H. Engelmann

The use of a suspended growth system of Thiobacillus ferrooxidans attached in a film to individual particles of bentonite and operated as a sequencing batch reactor is shown to be a practical way of oxidizing ferrous iron in acid mine drainage. This component, followed by limestone neutralization, is both a technically and economically feasible approach to treating these waste waters, compared to existing and other proposed methods. The advantages, in addition to less expense, are greater safety, acceptable treatment at a lower pH, lower solids buildup, less danger of overtreatment, and greater flexibility in operational characteristics. In this paper, data on the continuous bench scale operation of the system under a variety of conditions shows sustained levels of oxidation in excess of 98%. Capital and operating costs are projected to be $80/1000 m3 ($80 per 35, 000 cu ft) of waste water.

Jan 1, 1985