Search Documents

By L. J. M. Smits

A theoretical equation is developed describing membrane potentials of shaly sands as a function of the cation-exchange capacity per unit pore volume of the rock and saturating water salinity. This equation is based on the same simple physical model as that employed earlier7 describing the electrical conductivity of shaly sands. Experiments conducted with NaCl solutions showed that the equation is obeyed, except in the case of saturated salt solutions where minor deviations were observed. A possible explanation is given for this discrepancy. As the clay content and the porosity of shales may vary appreciably, shale membrane potentials also vary. It was found that membrane potentials of shales can be calculated accurately with the aid of the same theory. Consequently, changes in membrane potentials can be accounted for by simple measurement of cation-exchange capacities per unit pore volume of both shales and shaly sands. Charts are given to facilitate interpretation of the electrochemical part of the SP in terms of cation-exchange capacities and the salinities of mud filtrate and formation water. INTRODUCTION A spontaneous potential (SP) log is a record of the way in which the electrical potential of a sonde varies as it passes down a borehole. Such variations frequently reflect rock texture, e.g., permeable beds intercalated in an impermeable series often are indicated by a sharp change in potential. Nowadays it is recognized that SP logs may be interpreted in terms of formation-water salinity and formation shaliness. The four sources of the SP are illustrated in Fig. 1. El and E4 represent streaming potentials generated by the flow of mud filtrate through mud cake opposite permeable formations and through shale, respectively. An extensive review of the literature on the evaluation of these streaming potentials is given by Lynchl and will not be discussed here. The remaining part of the SP generally is called the electrochemical potential, which is divided into two parts: a membrane potential across the shale (E3, Fig. 1) and a membrane potential in the permeable sand at the diffusion boundary between formation water and mud filtrate (E2, Fig. 1). It was found by wyllie2 that the membrane potential across the shale, E3, is the most important contribution to the electrochemical potential, the shale acting as a semi permeable membrane. When the sand is clean it does not influence the diffusion process, so E2 equals the value of the so-called liquid-liquid junction potential observed when the two solutions diffuse freely into each other. When the sand contains clay, however, this interferes with the diffusion process and affects the diffusion potential generated. The greater the proportion of clay, the stronger this effect will be. Wyllie,3 Doll4 and Poupon et al.5 took this effect into account theoretically, starting from a physical

Jan 1, 1969

By F. S., Mc Nicholas

A practical discussion of the theory of A block caving is presented which applies particularly to the physical conditions of the Climax orebody although the conditions are sufficiently characteristic of caving ore-bodies to provide valuable information applicable elsewhere.

Jan 1, 1950

By H. J. Snyder

Both the room-temperature and 600°F (315°C) primary solid-solution phase boundaries for the silver comer of the Ag-Cd-In temary system have been determined using X-ray diffraction and metallo-graphic techniques. Solid solubility of indium in silver at room temperature and 600°F (315°C) is shown to be between 20.3 and 21.7 wt pct, and corrects the previously extrapolated value of 18 wt pct appearing in the literature. The solid solubility of cadmium in silver at room temperature, not previously established, is shown to be between 34.9 and 41.3 wt pct. The solid solubility of cadmium in silver at 600°F (315°C) is confirmed as 43.2 wt pct. The shape of the primary phase boundary line for the subject temary system appears straight at room temperature and curves con-vexly towards the solvent (silver) comer at 600°F (315°C). THIS investigation was undertaken to initiate development of the Ag-Cd-In ternary diagram by establishing the primary solid-solution phase boundary in the silver corner of the diagram. At the present time, a diagram for this ternary system is not available, while this system appears to offer potential for a variety of uses. One alloy in the system has already proven to be useful as a control rod material in nuclear reactors.1"3 To encourage additional exploration of the potential of the system an understanding of its ternary diagram would be beneficial. It is towards this end that the present study is directed. LITERATURE SURVEY In undertaking this study, a comprehensive literature survey was first conducted to find information that would be useful for guidance. Useful knowledge did result from investigating the respective solubilities of indium and cadmium in silver as indicated in the binary constitutional diagrams of the systems Ag-In and Ag-Cd and also reviewing possible shapes of ternary primary phase boundaries. Weibke and Eggers~ used metallographic techniques to establish the system In-Ag as illustrated in Fig. Is This diagram shows that silver in the solid state is capable of dissolving approximately 18 wt pct In. This solid solubility of indium in silver holds true from room temperature up to 1276°F (691°C), then decreases continuously up to 1'761°F (960.5"C), the melting point of the silver. The solid-solubility limit of indium in silver established by Weibke and Eggers has been confirmed by Hume-Rothery and Reyno1ds. G Durrant' used a method which consisted of microscopic examination of quenched specimens to establish the Cd-Ag system as displayed in Fig. 2.' The primary phase boundary of Fig. 2 proved to be in good agreement (ie., within 1 wt pct) with other studies*'1' of the Ag-Cd system made using X-rays and metallog-

Jan 1, 1968

By M. N. Dunlap

Tries article summarizes the successful incorporation of a flash-flooding stream into the tailing-disposal system at the St. Joseph Lead Company's Federal Division mill, in St. Francois County, Missouri. The mill was built in 1906, by the Federal Lead Co., as its No. 3 mill for the concentration of southeastern Missouri lead ores, and damming Davis Creek was first considered in 1908. Plans were made also in 1925 and in 1937. Dam layouts varied from a reinforced concrete structure to a barrier built of tailings alone. All were abandoned because of liability that would be incurred by flashflood rupturing of an incompleted dam. By 1942 mill capacity had reached 12,000 tons daily and increasing tailing-disposal costs again focused attention on the Davis Creek basin. This time the problem of riskless dam building was solved. Moreover, most of the items that appeared in the answer were materials that normally required wasting and the major portion of labor involved performed functions that it would normally have done, without constructive benefit, elsewhere. The new layout also made possible advantageous changes in mill-water supply pumping; static head being reduced from 514 ft to 95 ft, friction head from 4900 ft to 2860 ft, and pumping can be done now at periods of low power demand. The following facts about the Davis Creek watershed explain the 36-year reluctance to reach these, and other, benefits. Size: 3600 acres. Outline: roughly pear-shaped, 2 1/2 by 3 miles at the largest dimensions. Topography: mostly hill land with steep valleys. Relief : 760 minimum to 1153 maximum. Maximum rainfall: 3.36 in. per hour. Permanent water: none natural. Now 2200 gpm discharged through 16-in. drill hole from mine pumps underground. Geology: the 17 acres near dam centerline is Bonne Terre dolomite covered with sand and gravel eroded from Pleistocene beds that cap some of the hills. The remainder of the pond basin is on Davis shale. Soil cover: mostly second-growth timber with some abandoned fields; all subject to careless burning, which reduces water-retaining ability. Flood history: flash-flooding that had taken at least one life. Downstream values: two railroad bridges before creek intersection with Flat River. Immediately below confluence, a highway bridge, a low-water crossing, a few business establishments and several blocks of residences. In July 1942 the following segments of an ingenious plan were put into operation. A ditch 270 ft long, 16 ft wide and 5 1/2 ft deep was excavated to bedrock in the gravelly soil along the proposed dam's centerline. This excavation, which exposed many gravel-filled channels, was run full of slimes drawn from a riser set in the top of an adjacent tailings-disposal

Jan 1, 1947

Jan 1, 1940

The Ashanti mine is located in the Gold Coast region of West Africa in Ghana, where gold is found over a wide area of about 105,000 sq km (40,000 sq miles). Ashanti has been the most productive of all the lode mines and has been one of the world's notable gold producers for over 50 years. The mine is located at Obuasi, 113 km (70 miles) north and east of Tarkwa, which is 80 km (50 miles) inland from the coast. The Ashanti lode is worked on 300 m (1,000 ft) of strike length over a width of 12 m (40 ft), and by 1934 it had attained a depth of 700 m (2, 300 ft). The lode is in pre-Cambrian granite intruding a system- of shists, phyllites, etc., containing fragments of the wall rock with quartz, carbonates, sericite and small amounts of pyrite, arsenopyrite, sphalerite, galena, and gold. The shattered quartz fractures carry sulfides and gold, most of which are invisible. (William Harvey Emmons, "Gold Deposits of the World," McGraw -Hill, 1937.) Because the mill treats an ore composed of refractory sulfides - chiefly arsenopyrite and fine free gold - the flowsheet reflects the complex ore characteristics. Plane tables are used in the grinding, circuit for free gold recovery. After roasting the sulfide flotation concentrates, additional free gold is recovered from the calcines with a rotary belt concentrator and the two concentrates are combined for feed to the amalgamation pans, with the resulting gold amalgam being retorted. Following four-stage crushing to minus 9. 5 mm (318 in.) with two stages of grinding, the cyclone overflow is floated for sulfide recovery. The flotation concentrate is roasted with the calcine reground and roughly cyanided to scalp out the gold readily dissolved in one of two cyanidation circuits. The cyanide residue joins the thickened flotation tailing for cyanidation in a complete CCD circuit using filters. The gold precipitates are calcined before melting in pot-type furnaces. The tonnage to the mill of 3,175 mtpd (3,500 s tpd) with a content of over 14.7 g per mt (0.43 oz per st) places the Ashanti production as one of the top producers in the world; and with its past long life, the total production rates it as one of the world's great mines.

Jan 1, 1981

By L. J. Dijkstra

During the past several years an extensive study has been made of the internal friction of iron containing carbon or nitrogen in solid solution.1,2,3,4,5 It has been found that a sharp peak is observed in a plot of the internal friction vs. temperature of measurement. With a frequency of about one cycle per second, this peak occurs at 20°C for N and 36°C for C. The physical origin of this anomalous internal friction was traced by Snoekl to the local tetragonal symmetry of the interstitial positions in body centered cubic (bcc) iron. A change in stress induces a change in the equilibrium distribution of the interstitial atoms among the three types of interstitial positions, the three types corresponding to the three directions along which the tetragonal axis may lie. It is the continual striving of the interstitial atoms to maintain an equilibrium distribution that gives rise to a phase lag between strain and stress during oscillation, and hence, to internal friction. A similar type of internal friction has been observed in the bcc lattice of tantalum containing in interstitial solid solution C, N or 06. The theory of this anomalous internal friction leads to the prediction that its magnitude is strictly proportional to the concentration of either the carbon or the nitrogen in solid solution, provided the concentrations are small. This prediction has been verified3 for the range of solubilities ohtainable in alpha iron. This proportionality provides us with a new tool for the study of nitrogen and carbon in alpha iron. It thus enables one directly to follow the precipitation of either of these solute atoms from solid solution and also directly to measure their solubility as a function of temperature. A preliminary study of precipitation using this method has already been presented by the author.3 The purpose of this paper is to present more extensive observations upon the precipitation of N and C in alpha iron, as well as to present observations upon the solubility of N and C in alpha iron which, at least in the lower tempera- ture range, are believed more accurate than those previously obtained by other methods. The interpretation of the observations upon precipitation involves the use of the appropriate equilibrium diagrams. For ease of future reference in this paper the equilibriunl diagrams for the Fe-N and Fe-C systems are accordingly reproduced as Fig 1 and 2, respective]y. Experimental Procedure The specimens were made of West-inghouse Puron iron and consisted of wires 0.025 in. in diam and about 1 ft long. By a wet hydrogen treatment the specimens were purified of C and N. In

Jan 1, 1950

By ir. H. Eraly

At the Zolder mine a S/7 computer is used for two purposes : - to monitor production at the coal face - to monitor the distribution of mine cars. By using sensors attached to equipment at the coal face and at the loading points, the computer provides realtime information and also summarized reports, which help management to control production better. The computer will display this information to the control room, where two operators monitor all production events and the availability of the right numbers of mine cars at every production face. All benefits obtained from the system are described.

Jan 1, 1977

By William Sharp

Discovery of new ore in the Eureka district, Nevada, as a result of bold and persistent exploration based on a geologic interpretation of structure has recently aroused wide comment in mining circles. It may therefore be of interest to the profession to have a summary of the historical background and an account of the recent program of development. The mines of Eureka, discovered in the late 1860's, were the first important silver-lead mines in the United States. They have a production record of more than fifty-one million dollars.' After the ore bodies were apparently bottomed in the 1880's, repeated attempts to find new ore were unsuccessful until 1940, when a diamond-drill hole cut a 40-ft width of sulphide ore 1409 ft below the 841-ft level of the Locan shaft. The next hole cut 30 ft, of ore and three additional holes drilled in 1943 and 1944 showed the ore body to be continuous, Shaft sinking to reach and open up the ore body has been in progress since 1945. Geology Stratigraphy The ore in the Eureka district occurs in a series of Cambrian sediments which is exposed through a thickness of over 6000 ft. The stratigraphic column is as follows:2 Thickness. Ft Ordovician : Pogonip limestone (upper part). Thin bedded limestone with some chert. Upper Cambrian: Pogonip limestone (lower part). Thin-bedded limestone (with shaly limestone and chert).... 425 + Dunderberg shale. Shale (clay and calcareous shale) and thin-bedded limestone............. 34°+ Hamburg dolomite. Dolomite and limestone.................... 900+ Middle Cambrian: Secret Canyon shale. Shale and thin-bedded limestone........ 1,035 Geddes limestone. Carbonaceous, flaggy limestone with some shale partings................ 335 Middle (?) and LoweR Cambrian: Eldorado dolomite. Dolomite and limestone.................... 2,000 Lower Cambrian: Prospect Mountain quartzite. Quartzite with occasional intercalated conglomerate and shale 1,660+ The Prospect Mountain quartzite has been subdivided into two formations: Upper part, Pioche shale. Shale, quartzite with some intercalated limestone (Lower Cambrian fossils)-200 ft. Lower part, Prospect Mountain quartzite proper- 1,460Sft. Total thickness................ 6,695 + Much the most productive of these formations has been the Eldorado dolomite, which yielded more than $42,000,000 at Ruby Hill and an additional amount

Jan 1, 1949

By William Sharp

Discovery of new ore in the Eureka district, Nevada, as a result of bold and persistent exploration based on a geologic interpretation of structure has recently aroused wide comment in mining circles. It may therefore be of interest to the profession to have a summary of the historical background and an account of the recent program of development. The mines of Eureka, discovered in the late 1860's, were the first important silver-lead mines in the United States. They have a production record of more than fifty-one million dollars.' After the ore bodies were apparently bottomed in the 1880's, repeated attempts to find new ore were unsuccessful until 1940, when a diamond-drill hole cut a 40-ft width of sulphide ore 1409 ft below the 841-ft level of the Locan shaft. The next hole cut 30 ft, of ore and three additional holes drilled in 1943 and 1944 showed the ore body to be continuous, Shaft sinking to reach and open up the ore body has been in progress since 1945. Geology Stratigraphy The ore in the Eureka district occurs in a series of Cambrian sediments which is exposed through a thickness of over 6000 ft. The stratigraphic column is as follows:2 Thickness. Ft Ordovician : Pogonip limestone (upper part). Thin bedded limestone with some chert. Upper Cambrian: Pogonip limestone (lower part). Thin-bedded limestone (with shaly limestone and chert).... 425 + Dunderberg shale. Shale (clay and calcareous shale) and thin-bedded limestone............. 34°+ Hamburg dolomite. Dolomite and limestone.................... 900+ Middle Cambrian: Secret Canyon shale. Shale and thin-bedded limestone........ 1,035 Geddes limestone. Carbonaceous, flaggy limestone with some shale partings................ 335 Middle (?) and LoweR Cambrian: Eldorado dolomite. Dolomite and limestone.................... 2,000 Lower Cambrian: Prospect Mountain quartzite. Quartzite with occasional intercalated conglomerate and shale 1,660+ The Prospect Mountain quartzite has been subdivided into two formations: Upper part, Pioche shale. Shale, quartzite with some intercalated limestone (Lower Cambrian fossils)-200 ft. Lower part, Prospect Mountain quartzite proper- 1,460Sft. Total thickness................ 6,695 + Much the most productive of these formations has been the Eldorado dolomite, which yielded more than $42,000,000 at Ruby Hill and an additional amount

Jan 1, 1949

By J. H. Henderson, J. Naar

The displacement of a wetting fluid from a porous medium by a non-wetting fluid (drainage) is now reasonably well understood. A complete explanation has yet to be found for the analogous case of a wetting fluid being spontaneously imbibed and the non-wetting phase displaced (imbibition). During the displacement of oil or gas by water in a water-wet sand, the porous medium ordinarily imbibes water. The amount of oil recovered, the cost of recovery and the production history seem then to be controlled mainly by pore geometry. The influence of pore geometry is reflected in drainage and imbibition capillary-pressure curves and relative permeability curves. Relative permeability curves for a particular consolidated sand show that at any given saturation the permeability to oil during imbibition is smaller than during drainage. ' Low imbibition permeabilities suggest that the non-wetting phase, oil or gas, is gradually trapped by the advancing water. This paper describes a mathematical image (model) of consolidated porous rock based on the concept of the trapping of the non-wetting phase during the imbibition process. The following items have been derived from the model. 1. A direct relation between the relative permeability characteristics during imbibition and those observed during drainage. 2. A theoretical limit for the fractional amount of oil or gas recoverable by imbibition. 3. An expression for the resistivity index which can be used in connection with the formula for wetting-phase relative permeability to check the consistency of the model. 4. The Iimits of flow performance for a given rock dictated by complete wetting by either oil or water. 5. The factors controlling oil recovery by imbibition in the presence of free gas. The complexity of a porous medium is such that drastic simplifications must be introduced to obtain a model amenable to mathematical treatment. Many parameters have been introduced by others in Iprogressing" from the parallel-capillary model to the randomly interconnected capillary models independently proposed by Wyllie and Gardner3 and Marshall4. To these a further complication must be added since an imbibition model must trap part of the non-wetting phase during imbibition of the wetting phase. Like so many of the previously introduced complications, this fluid-block was introduced to make the model performance fit the observed imbibition flow behavior. THE IMBIBITION MODEL ASSUMPTIONS The following assumptions are common to many two-phase models previously described. 1. The wetting characteristics of the medium are clearly defined. 2. When two fluids co-exist in the medium, the wetting phase will fill the smaller pores and the non-wetting fluid the bigger ones. 3. The pores have a circular cross section. 4. Apparent pore radii are related to the capillary pressure (drainage) by

By Suresh P. Babu, Joseph W. Leonard

The ultimate objectives of comminution should be to reduce material to some specified size while producing a minimum of undersize or fines, with less power, higher throughputs, and with more compact machinery. Attempts to achieve these objectives have been only partially successful, since gains in some areas are achieved at the cost of concessions in other areas. An example of some of these trade-offs can be found in the closed circuit crushing operations of the anthracite and crushed stone industry where, in order to produce a minimum of unprofitable fines, unfavorable concessions must be made in the size of the crushing facility where 2 or more crushing stages are interphased by 2 or more screening operations. This paper discusses experiments with a new process which attempts to achieve some, if not all, of the comminution objectives in a single pass operation without undesirable concessions; or, at the very least, to achieve more than is possible with systems in use today. These objectives are sought by use of water-flushing to enhance comminution. The crushing of coal and other minerals is a mature technology that is long overdue for a careful re-examination. Crushing of coal is generally achieved through the use of rotary breakers and roll crushers. Water-flushing, as envisioned here, appears to have potential application in the following areas: 1) For primary raw coal crushing or for secondary crushing of rotary breaker products. 2) For use as a size reduction and/or concentrating step for crushing coal mine refuse from present production or from existing refuse dumps. 3) For possible future application in underground preparation interphased with continuous mining machinery. Size reduction with conventional methods is known to be an inefficient operation when the increase in surface energy of the material crushed is compared with the input energy. A simple breakdown of the energy consumption in size reduction, given by Orr, is shown in [Fig. 1]. It is believed that most of the energy supplied is lost in the form of interparticle friction.2 Hence, the removal of fines immediately after their formation or the implementation of steps to prevent their formation, based on reduced friction, will reduce the energy requirements of the communition operation.3 A detailed discussion of the mechanism of size reduction is available in other literature.3-5 Even though the closed circuit crushing operation is designed to carry the fines away from the crushing zone, it is still inadequate for instantaneous removal of fines. The present investigation advocates the use of a flowing liquid medium to remove the crushed product immediately after size reduction. Unlike the wet-grinding methods, no constraints are required for the liquid flow rate, and, also, the liquid medium can be used in primary crushers like jaw crushers, hammer mills,

Jan 1, 1978

By Z. F. Oszter, D. Vincent, W. K. Behrands

With the expansion of open pit operations, belt conveyors are going to be used in the 13 608 to 18 144 t/h (15,000 to 20,000 stph) capacity range, which calls for a review of some of the horsepower calculation methods. This paper presents methods (based on German research data, field tests and theoretical considerations) for the evaluation of the Ky factor in the CEMA formula for belt conveyors of large carrying capacity, which fall beyond the limits of the data given in tables in the CEMA book. (The CEMA limits are 407 N\\m (300 lb ft) and Tave = 7.3 Mg (16,000 lb). At these large loads, the impression resistance of the belting on the idlers plays a major role, which in turn influences the magnitude of the drive horse power required. An example will illustrate the order of magnitude difference of the horsepower values obtained by using a conventional calculation method and the suggested method, as well as the beneficcia1 influence of the 4-roll idler in comparison to the standard 3-roll unit for a large caving capacity belt conveyor. This paper concerns itself with the analysis of the resistance to motion of belt conveyors, emphasizing the evaluation of the frictional resistance to motion due to load and belt pressure on the idlers and the flexing resistance of the belt and material when passing over the idlers. In the case of long and heavily loaded belt conveyors, the aforementioned resistances reach extremely high values calling for close analysis of the phenomena, presently not calculable with normally used formulas. This paper establishes correlation between experimental and empirical data presenting practical formulas a tool for the designer of high-capacity belt conveyors. The application of the formula is illustrated in an example in the Appendix.

Jan 1, 1981

By J. J. Foster

MOST of us will, I think, agree that never before in the history of the coal industry has the human side of our business been so important as today. Since, even in wholly mechanized mining, labor cost is such a large percentage of out total cost we are all deeply concerned not only about the present attitude of our employees but particularly about the future, when the industry returns to a "survival of the fittest" basis. Many things could and should be done about our employee relations in the coal business. Failure to recognize these obligations and do something about them may lead to serious consequences, the least serious of which will be the loss not only of many of our better employees but a large portion of our potential employees, as they graduate from our schools to other in¬dustries. Some of these things should be handled by the industry as a whole whereas others should be done by individual companies. Due to varying conditions and size of organizations it would, at best, be necessary to vary a program to meet the individual needs of each operator.

Jan 1, 1945

THE progress in lead smelting practice in the United States during 1930 has been along previously defined lines. Since most of the material treated is high-grade concentrate relatively high in zinc, practically all the plants have been forced to adopt double sintering. This generally results in there being' no matte fall, and most of the copper in the charge is recovered in the furnace dross. The furnace dross is . smelted with. scrap iron and flux .in small reverberatories, giving a shipping matte or speiss high in copper and low in lead. Details of this reverberatory. furnace practice vary at the different plants. There is a decided tendency toward moreintensive filtration of blast- furnace and sinter fume. Bag capacity has been in- creased by using higher pressures and more frequent shaking.

Jan 1, 1931

By W. A. Mudge

This discussion will be limited to malleable, commercially pure nickel and some high-nickel alloys, containing more than 50 per cent of nickel, which are produced by The International Nickel Company, Inc. at its Huntington works, West Virginia, from electrolytic nickel or from a nickel-copper sulphide matte. The principal sources of nickel are sulphides of nickel, copper and iron, which are found in the large deposit of pyrrhotite-pentlandite-chalcopyrite ores in the Sudbury area of Ontario, Canada. Pentlandite, a complex nickel-iron sulphide, is the nickel carrier. These ores are concentrated, roasted, and smelted to remove considerable iron and sulphur and to produce a nickel-copper sulphide matte. Separation of the component sulphides of this matte, followed by electrolytic refining, results in the production of electrolytic nickel and electrolytic copper; direct refining of a selected portion of the matte gives the nickel-copper alloy, Monel. FUNDAMENTAL OPERATIONS Melting of the metallic materials is done in natural gas-fired, acid furnaces of the open-hearth, or reverberatory, type, having capacities of 6 to 20 tons; in three-phase, basic, electric-arc furnaces, having capacities of 7 to 20 tons; and in basic, high-frequency induction furnaces having capacities of ½ to 3 tons. Malleable, commercially pure nickel is melted in the acid open-hearth furnace. The charge is sulphur-free, electrolytic nickel, containing 99.9 per cent nickel* and clean mill scrap. Monel, containing approximately two thirds nickel and one third copper, is produced by roasting the nickel-copper sulphide matte to an oxide, smelting the oxide with charcoal in a 20-ton, acid open-hearth furnace, adding clean mill scrap, duplexing to a 20-ton, basic, electric-arc furnace, and refining in this furnace with a lime-fluorspar, carbide slag. Inconel, containing nickel, 80 per cent; chromium, 14 and iron, 6, is melted in the 7-ton electric-arc furnace or the 3-ton induction furnace. The charge is electrolytic nickel, ferrochromium and clean mill scrap. These are the fundamental operations. High-nickel alloys are produced from one of these three materials by additions of suitable amounts of manganese, aluminum, silicon or copper. For example, the age-hardenable alloy, K Monel, is produced from Monel by the addition of approximately 3 per cent of aluminum, and D nickel is produced from nickel by the addition of approximately 4.5 per cent of metallic manganese. For conversion to rods, bars, sheet, strip, tubing and wire forms, by hot-working and cold-working operations, the molten materials are teemed into ingots ranging in size from 14 by 14 by 60 in., 3300 lb., to 36 by 36 by 48 in., 18,000 lb. All ingots are overhauled mechanically before hot working.

Jan 1, 1946

By Sherwin F. Kelly

FRONTIERS of geological knowledge retreated further this past year before an ever-widening geophysical attack, as governments and endowed institutions continued to take an increasing practical interest in the geophysical line of approach to the study of earth phenomena. A year ago I opened this annual review with a brief account of the efforts to discover what formations lie concealed beneath the deep sediments which form the superficial portions of the Continental Shelf off the eastern United States. That work was but the beginning, and 1938 saw its continuation and expansion. With the assistance of a Guggenheim Fellowship, Maurice Ewing pushed his researches in the development of instruments and techniques for deep-sea seismic refraction studies. Ewing's early refraction profile from the Virginia Capes to the edge of the Continental Shelf has been followed by a similar traverse in Great Britain from the coast of Cornwall to the edge of the Continental Shelf southwest of England. This showed that the thickness of the sedimentary mantle and the rates of slope of the basement surfaces there are comparable to those in the Virginia Cape district.

Jan 1, 1939

By F. Weinberg

The relative concentration of 1" at grain boundaries in controlled orientation bicrystals has been examined by autoradiographic techniques, and by activity measurements of grain boundary surfaces exposed by preferential ,melting. The autoradio-graphs indicate that thallium is concentrated at grain boundaries in as-grown bicrystals, but not in zcell-annealed bicrystals. They also indicate that the solute concentration and the distribution on as-grown bicrystal surfaces are markedly different than that of the bulk material. The boundary surface measurements are in agreement with the autovadiographic evidence. On the basis of these measurements, as-grown bicrystals containing approximately 100 ppm of Tl, solidified at rates between 5 and 30 cm per hr and with tilt boundaries greater than 10 deg, exhibited grain boundary segregation equivalent to roughly 10 atomic planes of pure solute. Higher solute concentrations (equivalent to 140 atomic planes of pure solute) were obtained in bicrystals solidified slowly (0.6 cm per hr); slightly higher values were obtained in specimens containing a large angle nantilt boundary. Annealing for various times over a range of temperatures eliminated grain boundary segregation within the experimental uncertainty of the results (equivalent to 1 atomic Plane of pure thallium at the boundary). The results for the as-grown bicrystals can be qualitatively accounted for by assuming the presence of a groove on the solid-1iq;id interface, at the grain boundary. SOLUTE segregation at grain boundaries may be considered in two parts, namely, nonequilibrium segregation associated with the solidification process, and equilibrium segregation in fully annealed materials.' There is much indirect evidence for nonequilibrium segregation, based on preferential etching at grain boundaries and the mechanical properties of as-cast alloys. In addition, some direct observations have been reported in which radioactive tracers were used as solute additions and segregation detected at the grain boundaries by autoradiographic techniques. However, there is little detailed quantitative data on solute concentrations related to grain boundaries, particularly for different freezing conditions and grain boundary configurations. Equilibrium segregation at grain boundaries has been considered both theoretically and experimentally. cean' has made an estimate of the maximum equilibrium solute concentration that might be expected at a grain boundary, based on the lattice distortions in the boundary region. He arrived at a concentration which was equivalent t a monatomic layer of pure solute. A similar value, based on thermodynamic arguments, was calculated by Cahn and Hilliard for the segregation of phosphorus in iron. Experimentally, much higher values of solute concentration at grain boundaries have been reported recently by both Inman and iler' for phosphorus in iron, and Ainslie et 1.' for sulfur in iron. They observed concentrations equivalent to as much as 20 to 100 atomic layers of pure solute at the grain boundaries. However, in both cases it was shown that the observed segregation was not due solely to equilibrium segregation at the grain boundary. In the former case, precipitation effectss due to trace impurities in the material were believed to account for the large amount of solute present at the grain boundary. In the latter case it was shown that a high density of dislocations in the boundary region could provide a large number of additional sites for solute atoms, other than at the grain boundary. Thomas and chalmera have reported on the equilibrium segregation of po210 in grain boundaries of Pb-5 pct Bi alloys. Using autoradiographic techniques, they observed a concentration of polonium along the boundary trace on the surface of annealed bicrystal specimens grown from the melt. The concentration only appeared after annealing, and varied with boundary angle, increasing as the boundary angle increased. Their conclusions have been questioned by Ward," who pointed out that the segregation they observed along the boundary trace was much too wide to be compatible with the usual concepts of the thickness of a grain boundary of several lattice spacings. Also, Maroun et al.,l1 with specimens similar to those of Thomas and Chalmers, found that segregation could only be detected on the specimen surface, suggesting that Thomas and Chalmers' results were associated with an oxidation effect of polonium, and not equilibrium segregation. Thomas and Chalmers replied12 that they did observed segregation at the grain boundary in the bulk material and suggested further experiments were necessary to resolve the difference. The purpose of the present investigation was to examine both nonequilibrium and equilibrium grain boundary segregation in melt grown bicrystal specimens as a function of boundary angle, growth rate, and solute concentration, and to de-

Jan 1, 1963

By J. A. Retty

IN the Labrador iron fields two concessions, totaling nearly 24,000 square miles, have been staked out and commercial-grade deposits delineated. The Newfoundland-Labrador concession, owned by the Labrador Mining and Exploration Co. Ltd., is a 20,000-square-mile tract in the upper basins of the Hamilton and N askaupi Rivers which drain into Lake Melville. The New Quebec licensed area is 3900 square miles, owned by the Hollinger North Shore Exploration Co. Ltd., lying to the northwest of the northwestern part of the Labrador concession. It includes the upper basin of the Swampy Bay River and part of the upper basin of the Whale River, both of which drain into Ungava Bay. Both of the above-named companies are controlled by Hollinger Consolidated Gold Mines Ltd. with The M. A. Hanna Co., of Cleveland, holding a minority interest. When exploration was first undertaken in 1936, the only published map of the area was that prepared by A. P. Low in 1895. It showed only the main watercourses and gave only a rough, general idea of the geology. The numerous lakes of this vast area had to be first sketched and then mapped. Since then, extensive geological and topographical surveys have been conducted by the Labrador company, work which is normally done by Government branches. The object of the work was to examine the area and gradually eliminate unfavorable or less favorable prospecting ground. With this object in view, geological

Jan 1, 1948

By Arthur Glance

MINE safety is of the utmost importance to all operators and most operations have a safety organization, or safety inspector, whose job it is to be continually on the alert to detect and correct the hazards of mine operation. Reports from the Bureau of Mines show that next to roof falls, gas presents the greatest hazard in mining. The Bureau of Mines Information Circular 6680 shows that 162 explosions occurred in the United States during the five-year period ending June 30, 1932. Deaths resulting from these explosions amounted to 984, with a great many disabled and disfigured. A fatality rate of 6.07 persons shows the ex¬treme severity of this hazard to the industry. Various mine appliance companies have put on the market instruments for methane detection, which record in direct percentages the amount of methane present in the atmosphere. Unfortunately, few mining companies are using these instruments, however. Those available include the Burrell methane detector, the Wolf, the Martienssen, the Mine Safety Appliance detector, and the Union Carbide Company methane detector, which last I have used extensively in making mine inspections.

Jan 1, 1936