Search Documents

By CHARLERS R. FETTEE

A slight decrease in drilling activity occurred in the oil fields of western Pennsylvania during 1945 and a considerable decrease in the shallow-gas territory (Upper Devonian or higher). The number of deep tests (Middle Devonian or deeper) completed was two less than in 1944 and these did not open any new reserves of natural gas. Thus far, no commercial oil has been encountered in sands below the Upper Devonian in Pennsylvania. Oil production declined 8 per cent.

Jan 1, 1946

Jan 1, 1885

AS provided in Article VIII, Section 4 of the By- laws, the Papers and Publications Committee has formulated the following, rules of pro-cedure and submitted them to the Board of Directors for consideration and approval. In preparing these rules the committee, and an active subcommittee con-sisting of Messrs. Norris, Sharpless; Fohs and Wither-ell, have kept in mind the desirability of codifying the practice that has grown up through the now sev-eral years of experience of the committtee, without casting them in a mold so rigid as to be hampering. The problems of the Institute change from year to year and the methods of publication must change also to meet each new situation as it arises. "The estab-lishment of divisions and special volumes devoted to the papers. read before each required certain changes from former practice. These rules have been framed with this in view. The committee suggested, however, in its letter of transmittal, that the system will be made all the more workable if the Board will, as far as practicable, in making appointments to this committee, arrange for representation from each of the professional divisions and technical committees. It is understood that the chairman of the committee will be named by the Board. The rules regarding spe-cial volumes have been framed, keeping in mind the present policy of distribution, as already approved by the Directors under which the special volumes go only to the special. groups except on request. The committee has not attempted to provide rules governing consideration of any appeal made to the Board from one of its decisions, but its services and files will necessarily be at the full service of the Board in any such event. The rules which were ap-proved by the Board at its meeting on March 30, 1928, are as follows: Signed by C. S. Witherell, Chairman. (A) The authority of. the Committee on Papers and Pub-lications, hereinafter called the Committee, is defined in Art. VIII, Sec. 4 of the By-laws of the Institute, which reads as follows: "Papers and Publications: The Committee on Papers and Publications shall consist of the Secretary of the Institute, and at least twelve members of the Institute, to assist in passing on all papers offered for publication. They shall be appointed annually by the Board of Direc-tors, on recommendation of the President, and shall have authority, subject to appeal to the Board, to accept or reject papers for publication in the Transactions and Technical Publications of the Institute. The Commit-tee shall formulate a set of rules of procedure which, when approved by the Board, shall have the force of By-laws until revoked or amended." The policy of the Committee will be to uphold the ob-jects of -the Institute as set forth in the Constitution (Arti-cle 1, Sec. 2).

Jan 5, 1928

By F. J. Zuiderweg, G. G. Bemer

Results of a study aimed at assessing kinetics and mechanisms of the batch agglomeration process in suspension are discussed. A recently developed light backscatter technique which enables the increase of average particle size from 1 to 5000 µm to be followed, was used to determine agglomeration kinetics. Growth curves and agglomerate size distributions were obtained in a stirred vessel for various model systems and operating conditions. Four distinct growth regimes were identified, i. e. the flocculation regime, the zero-growth regime, the fast growth regime, and the equilibrium regime. Further, it was observed that large differences in the occurrence and duration of these regimes resulted from small variations in parameters, such as size distribution of the initial particles and the binding-liquid to solid ratio. Mechanisms that determine the occurrence of the relevant regimes are discussed. The growth process was described in terms of population balance equations. In this way, the growth rate, the equilibrium agglomerate size distribution, and the evolution of the agglomerate size distribution were generated. The agreement with experimental results is satisfactory.

Jan 1, 1980

By E. T. Hayes, A. H. Roberson, M. H. Davies

ZIRCONIUM has been produced on a pilot-plant scale for only a few years, but the potential uses have led a large number of research establishments to engage in a thorough study of the metal and its alloys. The work described in this paper is part of a cooperative project between the Bureau of Mines and the Air Materiel Command. The Zr-Cr system was one of the first investigated because of the possibilities of improving the properties at elevated temperatures, the chemical corrosion resistance, and the mechanical properties of zirconium in a manner similar to the enhancement of the properties of titanium by additions of chromium. There is no published work on the Zr-Cr system but from the similarity of the metals involved it was expected that it would be similar to the Zr-Fe' and Ti-Cr' systems. The materials used in this investigation were prepared in the Bureau of Mines laboratory at Albany, Ore. Zirconium was produced by magnesium reduction of zirconium tetrachloride, and a typical analysis is as follows: Fe, 0.06 pct; Ox, 0.08; N?, 0.01; C, 0.02; and other impurities such as Al, Pb, Ni, Ti, and Si less than 0.01 pct each. High purity chromium was prepared by treating crushed electrolytic chromium in a stream of dried and purified hydrogen." The resulting powder contained about 0.01 pct 0 and about 0.1 pct total metallic impurities. All alloys were prepared by arc-melting 50 g briquetted compacts of the desired composition in a Kroll-type" arc furnace using an inert atmosphere. The furnace was evacuated twice and backfilled with helium, which was gettered by melting a center zirconium button immediately before the alloys were melted. Alloys were remelted at least once to insure greater uniformity of composition and subsequently were annealed in vacuum at 1250°C for 48 hr. Fairly homogeneous alloys were obtained by this means; a slight loss of chromium from the surface by evaporation during the high temperature homogenization was noted. All alloys were analyzed for chromium and gave results in good agreement with the nominal composition. Spot checks on tungsten and nitrogen showed pick-up of these elements to be negligible. Over 70 alloys were prepared for use in this investigation; only the critical ones are shown in Table I. Alloys containing up to 10 pct Cr were amenable to hot working at 850°C and a number of these were sheath rolled to 1/16 in. thickness. Specimens were cut from the sheet for use as metallographic samples. For the thermal analysis a differential couple was used in conjunction with an X-Y recorder, the temperature of the specimen and the difference in ternperature between it and the standard nickel body were recorded simultaneously. Heating and cooling rates of 5°C per min were used. The sensitivity of the instrument was such that a difference in temperature between the specimen and standard equivalent to 0.1 mv produced a deflection of 1 in. on the recording chart. The chromel-alumel thermocouples were checked against a Bureau of Standards calibrated thermocouple. Melting-point determinations were made in a high vacuum induction furnace using an optical pyrometer. The pyrometer, calibrated against nickel, copper, and zirconium (iodide process) under near black body conditions, was focused on the base of a hole drilled in cylindrical samples. A North American Philips Geiger counter X-ray spectrometer was used for all diffraction studies. This instrument, in addition to supplying precise intensity measurements of planar reflections, has an added advantage in that metallographic specimens mounted in bakelite can be used directly, and this

Jan 1, 1953

By H. S. Drinker

I. The Mines THE first discovery of zinc on the property now worked by this company was made by the celebrated mineralogist, Prof. William Theodore Röpper, in 1845. Different claimants kept the property in continual litigation till 1861, when everything was satisfactorily settled by the purchase of the land by the company, who have worked it ever since. The mines are situated in a valley, four miles south of Bethlehem, Pa., in Lehigh County. The valley is from two to three miles broad, and is bounded on the north and south by syenitic hills. Syenite underlies the valley, and upon this is deposited the Potsdam sandstone, then a layer of slate, and, finally, a dolomitic limestone, belonging to the Chazy or Black River formation, in which the zinc deposits are inclosed. The rocks occur in folds, and have evidently been subjected to tremendous pressure from below, the zinc deposit being found in an anticlinal axis, in nearly vertical veins. It is supposed that the zinc was originally disseminated through the

Jan 1, 1873

By Michel L. Bilodeau

The objective of delineation drilling is to provide a data base for the tonnage and grade estimates required to evaluate the economics of mine development. As drilling information is accumulated, geological risk is reduced and more reliable estimates of tonnage and grade are obtained. Investment in drilling is justified by the benefits which result from improving the reliability of the economic criteria evaluated. These benefits are subject to diminishing returns, i.e. as drilling information is accumulated the reliability of the economic criteria evaluated is improved but at a decreasing rate. At the same time, costs are incurred -- the direct investment cost associated with additional drilling and the time cost of delaying possible production revenues. The economic sampling limit is de- fined by the point at which the marginal benefits from drilling investment just balance the marginal costs. The paper describes the formulation of an economic model to optimize investment in delineation drilling. The model is applied to a simulated mineral deposit to illustrate the economic effects of a sequential drilling program.

Jan 1, 1977

By G. A. Koenig, Moritz Stockder

Locality and Geological Occurrence. The Alpine region of Southwest Colorado, comprising the San Juan and Uncompaghre Mountains, is composed of a deeply eroded sheet of acid eruptive rocks, overlying in part gneissic sehists, and in part limestones and sandstones, including portions of the Silurian, Devonian, and Carboniferous systems. The section is clearly and beautifully exposed along the Uncompaghre River from its headwaters to its exit from the mountains. The river's course from the town of Ouray towards the Los Pinos agency is due north, and four miles from Ouray, in this direction, the Uncompaghre receives from the east the Red Cafion Creek. Following up the narrow caftan we find the section through white.. sandstone in strata dipping to the north and west, and belonging either to the lower or middle Devonian system. Presently the steep cafion-liko character of the ravine gives place to more gentle slopes, and we have entered crystalline rock-porphyry. The contact is well marked, for the sandstone, to a depth of from six to ten feet, resembles quartzite, i. e., is semifused. Ascending still higher, a small

Jan 1, 1881

By H. W. Morse

THE CHAIRMAN (H. W. MORSE).-Gentlemen, for the first time in the history of the American Institute of Mining Engineers, we have a full session on the subject of leaching-especially on the leaching of copper ores.. This branch of metallurgy is rather in its infancy. We have had one big plant running for a year or more, and pretty successfully; and another one which will be started in February or March, the New Cornelia. We have another one at Garfield for the Utah company, which is just designed and construction begun; and from several other points come reports of interesting test work. The first paper on the program this evening is one of some of the test work on the New Cornelia ore by myself and Mr. H. A. Tobelmann. LAWRENCE ADDICKS, New York, N. Y. (written discussion).-The Ajo proposition has had, as I understand it, two great advantages: it has not been obliged to measure leaching against flotation or some other metallurgical process, and it deals with a copper content high enough

Jan 12, 1916

F. W. Gordon, Philadelphia, Pa.: There can be no objection to the use of cross-compound blowing-engines; and when they are condensing they are susceptible of great range of duty with slight loss in efficiency. By those who have use for the full heat of the waste gases, this type of engine is advantageous; but many furnaces are not so located. The pig-iron is their finished product, and the gases are to be employed only for furnace-use. In this case simple engines are preferable, being less expensive and having less parts to take care of. These reasons determined the introduction of the engines, a sketch of which is distributed at this session. There are three of these engines to furnish blast for two furnaces, for a make of abont 250 tons per day, using 75 per cent. anthracite and 85 per cent. magnetic ores; and they are expected to blow up to twenty pounds pressure per square inch. For blast-furnaces I prefer the single to the coupled engine, except

Jan 1, 1894

By William G. Kranz

Discussion of the paper of WILLIAM G. KRANZ, presented at the San Francisco meeting, September, 1915, and printed in Bulletin. No. 101, May, 1915, pp. 927 to 930. M. PETINOT, Niagara Falls, N. Y. (communication to the Secretary*). -I have read this paper with considerable interest and agree perfectly with Mr. Kranz that steel for castings made in an electric furnace is not necessarily, because of that fact, all good steel, and also that the qualities which he mentions, such as absence of segregation, elimination of `sulphur, great tenacity, etc., can be obtained in an electric furnace if operated under proper metallurgical conditions. An unusually low content of sulphur in steel for castings is not, of course, an absolute necessity and the range of this element usually obtained in steel made in basic open-hearth furnaces is sufficiently low to meet all physical requirements. The main factor in making steel for castings, regardless of the process, is the complete deoxidation of the bath to prevent the formation of

Jan 12, 1915

By Cyril Stanley Smith

BeTa brass (consisting of approximately equal atomic proportions of copper and zinc) exists as a random solid solution at high temperatures, hut at low temperature< an ordered structure is stable, with the copper and zinc atoms occupying alternate sites on the body-centered-cubic lattice. On cooling, ordering commences at a temperature of 450° to 470°C., depending on the composition. The degree of ordering progressively increases at lower temperatures until it becomes virtually complete at about 100°C. The electrical resistivity of the alloy illustrates the changes clearly (Fig. I). This type of reaction has been a favored subject for study by physicists. An excellent summary of the theory is to be found in a paper by F. C. Nix and W. Shock1ey.l All published data on electrical conductivity, specific heat and other properties agree in indicating that the ordering reaction in beta brass takes place so rapidly that it cannot be prevented or even retarded by quenching&apos; With most ordered alloys, cold-working induces disorder and

Jan 1, 1943

By Cyril Stanley Smith

BeTa brass (consisting of approximately equal atomic proportions of copper and zinc) exists as a random solid solution at high temperatures, hut at low temperature< an ordered structure is stable, with the copper and zinc atoms occupying alternate sites on the body-centered-cubic lattice. On cooling, ordering commences at a temperature of 450° to 470°C., depending on the composition. The degree of ordering progressively increases at lower temperatures until it becomes virtually complete at about 100°C. The electrical resistivity of the alloy illustrates the changes clearly (Fig. I). This type of reaction has been a favored subject for study by physicists. An excellent summary of the theory is to be found in a paper by F. C. Nix and W. Shock1ey.l All published data on electrical conductivity, specific heat and other properties agree in indicating that the ordering reaction in beta brass takes place so rapidly that it cannot be prevented or even retarded by quenching&apos; With most ordered alloys, cold-working induces disorder and

Jan 1, 1943

By Joseph Newton

MUCH the same story can be told about the copper industry for the year 1944 as for the three preceding years. Operators report few or no technical changes at their plants and the main endeavor has been to maintain high production with existing equipment. No large new installations have been made to increase plant capacities and apparently over-all copper production has passed its maximum. The present decline in copper production results partly from the severe labor shortage. As is true of most industries; the outstanding fact about the copper industry during the past few years has been its tremendous and sustained production which has been maintained in spite of serious shortages in material. labor, and technical personnel. The figures in Table I give a concrete example of how production has been increased at one large smelter in the United States-the Garfield plant of the American Smelting and Refining Co. at Garfield. Utah. These figures, reported by W. G. Rouillard. superintendent. give the production of the Garfield plant for the five years 1940-44 inclusive. The total blister production

Jan 1, 1945

By J. C. Bayles

An obstacle to the more careful and satisfactory study of metals has been the difficulty in harmonizing the results of chemical and physical tests. These give us records of observations made from different and often widely separate points of view, and while it is true that they furnish bases for more or less accurate triangulations into the realm of speculation, it is doubtful if, with only the laboratory and the testing machine, our investigations would not move in parallel lines, leaving between them an unexplored field in which must probably be sought the information which shall connect the results of chemical and physical tests, and give to both a practical value which neither has yet been found to possess. The use of the microscope in the study of metals is not a new thing, but it is only lately that it has begun to attract the attention it merits or to show results of tangible value to the metallurgist. Among recent valuable contributions to the literature of this subject, I have been especially interested in the work of Mr. A. Martens, of

Jan 1, 1883

By J. G. Bradley

On February 1, 1971, United States Steel Corporation, Lorain Works began operation of its first BOP facility equipped with a partial combustion gas cleaning system.- This shop consists of two 220 ton vessels. Figure I schematically describes this partial combustion gas cleaning system and highlights the necessary features for it-s safe and efficient operation. Waste gases are drawn into the membrane hood by a 2250 H.P. induced draft fan and are first quenched by the six inch bull nozzle at the top of the hood. Larger solid particles are separated from the gas in the quencher venturi and final scrubbing takes place in the P-A high energy venturi scrubber before the cleaned waste gas is burned in the flare stack. Scrubbing water is routed through a cyclone separator and then cycled into one of two 100&apos; diameter thickeners. Underflow sludge which averages 20% solids is dewatered by 100 H.P. centrifuges. The clear overflow from the thickeners is recycled first to the P-A venturi and then to the quencher before returning to the thickeners.

Jan 1, 1972

By A. H. Roberson, L. H. Banning

DURING the past few years, a considerable tonnage of ilmenite has been produced as a byproduct of a monazite dredging operation and stockpiled near Boise, Idaho. This ilmenite has not been marketed because of the long distance from ilmenite-consuming areas and its comparatively low TiO2 content. Production of monazite from the alluvial sand deposits of Idaho is a mar- ginal venture when it is the only marketable product, and it will be necessary to establish a byproduct market before the operation becomes economically stable. Early in 1954, the Bureau of Mines Northwest Electrodevelopment Laboratory at Albany, Ore., conducted a series of tests which demonstrated that arc furnace smelting could be utilized to produce commercial quality pig iron and a high titanium content slag from these ilmenites. Additional studies showed that the slag chlorinated readily to produce a satisfactory yield of TiCl4. The investigation was carried out by two research teams. The Ferrous Metals Branch, with adequate

Jan 1, 1956

By Gerhard Derge

METALLURGISTS have used borax as a fluxing agent traditionally, but until recently elemental boron has played an insignificant role as an alloying element. Neither the metal nor its compounds have been regarded as important metallurgical materials and there is a surprising lack of knowledge concerning their metallurgical behavior. The new applications to steelmaking of both boron and borates, which arose in part from wartime incentives and restrictions, have been seriously handicapped by this lack of data. For example, rasorite, a naturally occurring sodium borate, has been shown to be an effective substitute for aluminum as a ladle deoxidizer in rimming steels.1 Likewise, the effectiveness of boron as an alloying agent has been demonstrated, 2,3 giving deep hardening when used in restricted amounts. The exploitation of both of these uses has been retarded by the difficulty of attaining suitable metallurgical control. Recognizing that the most important information required was a knowledge of the equilibrium between boron and oxygen dissolved in liquid iron, Gurry4 calculated this relation from the best thermal data available. However, estimates of the entropy of melting of boron, the activity coefficient of boron in liquid iron and the activity coefficient of B203 in slag were involved, and experimental work on this problem was obviously desirable. The experiments to be described were planned to establish the boron-oxygen relations in liquid iron and to demonstrate at the same time the ferroborate slag compositions in equilibrium with various amounts of oxygen in liquid iron. Accordingly, slags containing varying proportions of iron and boron oxides were held in contact with molten iron, and samples of both slag and metal were analyzed. The limitations upon the accuracy of the data will be considered, but in a practical sense the oxygen levels that can be attained in iron by iron borate slags, and the amounts of boron in iron at these oxygen levels were established. EXPERIMENTAL PROCEDURE No entirely suitable refractory was found for the mixtures of iron oxide and boron oxide used as slags. Crucibles of silica, magnesia, Ramix, beryllia, and zirconia were all tried unsuccessfully. The most satisfactory method discovered for handling them was the rotating-crucible technique, which creates a parabolic crucible of liquid iron 5,6 Even this was not entirely successful, for at steelmaking temperatures (1600°C.) the slags had such a low surface tension that they crept up to the refractory and slowly dissolved it. These difficulties made it impossible to maintain a constant slag composition for an unlimited period of time. However, by using the rotating

Jan 1, 1946

By Paul T. Allsman

Passage of the Mining Act of 1866, superseded by the Act of 1872, was the first major entry of the Federal Government into the problems of mining. Such a law was necessary simply to help re- solve a number of disputes in mining. Now, however, a hundred years later, the extent of government involvement in the mineral industry often comes as a shock to the mining engineer who has reached management level. In fact, he has been poorly prepared for an understanding of the role of government in the industry and he becomes frustrated, even hostile. In our political system, private industry is responsible for producing minerals and the Government sees to it that production will be adequate for a peace-time economy and for any emergency. There have been great social and political changes since World War I1 with the result that the Government&apos;s participation in our society has steadily increased. A new dimension in business and government relations has been introduced which should be examined more closely.

Jan 5, 1966

By Francis L. Vinton

THE eccentric theodolite I exhibit is one constructed by the Stack-poles of New York, from drawings, considerably modified, of Combes&apos;s theodolite. The telescope is on one side of the horizontal limb, and the vertical circle is opposite to the telescope; thus they nearly balance each other, making already the construction lighter than in the instrument of Combes, where the telescope and vertical circle are together on the same side, and are both balanced by a considerable weight. The instrument stands upon three levelling screws or feet, an improvement upon the old or general style of mounting a transit on four feet-for indeed the instrument is easier levelled, and, more-over, stands more stable on three than on four points of support. The general advantage of an eccentric theodolite is evident, namely, that it can measure any and all vertical angles, from 0 to 360, without being interfered with by the horizontal limb as is the transit; besides this advantage, it needs no preparatory adjustment or correction for eccentricity ; on the other hand, however, that correction

Jan 1, 1873