Search Documents

By T. K. Prentice

The January-February number of the Journal of the Chemical Metallurgical and Mining Society of South Africa, 1943, is made up entirely of a discussion of Ball Wear in Cylindrical Mills. Following the principal paper by T. K. Prentice are several remarkably pertinent and carefully prepared discussions. Few persons in this country would be likely to see this publication, and since the information presented is new and of current interest, it seems desirable to abstract and review this publication for the benefit of the members of the A.I.M.E. The purpose of the investigation is stated in the first two paragraphs of Prentice's paper, as follows: Early in 1941, The Chamber of Mines Steel Products, Limited, initiated a series of tests under semi-working scale conditions to determine, if possible, those physical and chemical properties of a ball which make it resistant to wear when used in a cylindrical mill as a grinding medium, with the primary object of incorporating those beneficial qualities in the balls being produced at their works. This paper describes the tests carried out and discusses the results obtained. From these results it was possible to formulate a new theory relating to ball wear in cylindrical mills. This theory is presented in the second portion of this paper. Practical Ball-mill Tests in a Cylindrical Mill Part I of the paper begins with a discussion of the methods used for the manu- facture of grinding balls in South Africa. The following paragraph is of particular interest. The cast steel ingots, 4¼ in. square by 3 ft. 6 in. long, are re-heated in a gas-fired sloping stationary-hearth furnace and then rolled in a six-pass continuous mill into 25/8 in. round billets. Some of these billets are then removed and cut into suitable lengths for forging into 4 in., 3¼ in. , 3 in. or 2½ in. balls by means of three Drop and two Beche hammers, but the greater number, whilst still at about 1,000, pass directly into a set of scroll rolls which produce, in an ingenious manner, finished 3 in. balls direct from the 25/8 in. billets. Except in special cases, all balls are allowed to cool in the atmosphere and are not water quenched. Details of the Tests In order to enable the reader to evaluate properly the results and conclusions in the rest of the paper and in the discussions following the paper, most of the information presented by the author under this heading is quoted: The testing unit was a nominal 30 in. diameter and 18 in. long centre discharge Denver Ball Mill. The ore pulp to the ball mill comprised a small portion of the normal feed to one of the fourteen City Deep 5 ft. 6 in. X 22 ft. tube mills, and the grinding media consisted of the balls under test plus other balls to give the desired load. The running time of the test-mill was divided into approximately equal periods of five days 13½ hours each. The usual procedure was to examine and make up the load

Jan 1, 1947

By B. Lustman

IT has been known for a number of years that the addition of certain alkaline-earth and rare-earth metals to nickel-chromium base electric resistance alloys causes marked increase in their oxidation resistance as measured in an intermittent oxidation test similar to the ASTM—B 76-39 test. However, the mechanism whereby such additions confer protection is still unknown. On the basis of the experimental observation that the increase in life in intermittent tests of nickel-base alloys is proportional to the atomic radius of the added element, Hessen-bruchl has proposed that the added metal ions occupy holes in the oxide lattice which prevent diffusion of nickel ions in the oxide. Horn2 has postulated that the effect of such additions is to accelerate the rate of diffusion of chromium atoms in the metal and thus to favor the formation of Cr2O3 scales. Hickman and Gulbransen3 concluded from electron diffraction observation that the addition of the elements in question results in the formation of a barrier to the diffusion of nickel ions to the surface. In connection with some experiments conducted to develop a test for the resistance to oxidation of alloys in massive form under conditions of intermittent heating and cooling, some features of the oxidation of nickel-chromium base alloys were revealed which may serve to elucidate the mechanism of protection conferred by rare-earth and alkaline-earth elements. Specimens of cylindrical shape 0.360 in. diam x 0.37 in. long were placed in alumina thimbles and inserted into and withdrawn from a Globar-heated furnace operating at 2150°F at 7.5-min intervals. The weight of oxygen absorbed as well as the weight of oxide spalled were measured at intervals. With the particular experimental conditions used, the specimens in a 7.5-min cycle were at temperature for 2 min which corresponds to the heating time of the ASTM test. The weight changes of similar specimens under conditions of continuous heating in air at 2150°F were also measured. The specimens after oxidation were examined metal- lographically and samples of the spalled oxide collected for X-ray diffraction identification of the phases. The specimens used were from the same lot of material used by Hickman and Gulbransen3 and had the compositions shown in table 1. Included in table I are results of ASTM life tests on the materials in the form of wires. These materials, their composition and the ASTM life test data thereon were all supplied by F. E. Bash of the Driver-Harris Co. It may be noted that alloy 13246 of 80 pct nickel, 20 pct chromium nominal composition showed the shortest life in the ASTM test; alloy 12246 with the addition of small amounts of the elements zirconium, calcium, and aluminum, intermediate life; and alloy 12046 with the further addition of silicon, the longest life. In fig. 1 are shown the results of intermittent oxidation tests made on bulk specimens at 2150°F as well as continuous tests conducted at the same temperature. Duplicate tests were made on each specimen. The ordinate scale, inches of metal oxidized, was derived from the experimentally observed weight gain of oxygen by assuming the scale to be entirely Cr2O3. It may be noted that the metal-loss curves during intermittent oxidation show a constant or continuously increasing rate of weight

Jan 1, 1951

By W. C. Ellis, E. S. Greiner

METALLIC titanium has been prepared in small quantities since the beginning of the century. Hunter1 reported in 1910 that he obtained a malleable product of 99.9 pct purity by the reduction of the tetrachloride by sodium in a closed container. Later Van Arkel2 and Fast3 prepared small quantities of malleable titanium by thermal decomposition of titanium iodide. Another method for producing malleable titanium from tetrachloride was reported by Kroll4 who used magnesium as the reducing agent. More recently Dean, Long, Wartman, and Anderson5 working at the U.S. Bureau of Mines have reported the preparation of the metal on a pilot plant scale by the reduction of titanium tetrachloride by magnesium in an atmosphere of helium. Their product, which is malleable, was used in the present investigation. Early in 1948 after the work of this paper: was completed Campbell, Jaffee, Blocher, Gurland, and Gonser6 described the strength and working characteristics of pure titanium which was prepared by the iodide method on a scale producing 300 to 600 g per run, in the form of 0.3- to 0.4-in. diam rods. Their product is characterized by low hardness and large capacity for cold work which they attribute to a high degree of purity with respect to oxygen, nitrogen, and carbon. Titanium has a melting point of about 1725°C5 it may be classed as a light metal since the specific gravity is 4.5 g per cc-1. The crystal structure is close-packed hexagonal from room temperature t0 885°C. Above this temperature the structure is reported7 as body-centered cubic. The change in crystal structure has been associated with discontinuities in specific heat8 electric resistance9 and thermoelectric force10 at temperatures near 890°C. It is reported11 that annealed titanium has a tensile strength 0f 78,700 psi which can be increased by cold-work to 123,000 psi. In the present investigation, the lattice constants at room temperature, the thermal expansivity between 30 and 800°C, as well as the electrical resistivity and thermoelectric force against platinum between - 200 and 1000°C have been determined. MATERIALS For the measurements, two series of specimens were prepared from titanium furnished by the U. S. Bureau of Mines. The first was lade from an annealed sintered compact, 0.38 in. thick. Sections of the compact were cold-swaged with intermediate anneals in vacuum to the sizes used. Sizes over 0.25-in. diam were annealed at 1000°C and smaller sizes at 800°C. Specimens originating from the sintered compact are designated in this paper as A. The second series of specimens was lade from a rod of titanium, 0.19 in. in dial, which was cold-swaged with the necessary intermediate anneals to the required sizes. This series of specimens is designated B. The impurities in the specimens of titanium, determined by chemical analysis, are given in Table I. Oxygen and nitrogen which were not determined by analysis, are probably present although in small quantities in view of the ductility of the material.

Jan 1, 1948

By Henry M. Howe

(Cleveland Meeting, October, 1912.) Manuscript received Aug. 20, 1912. PROFESSOR RUFF'S most illuminating paper' describing his extremely valuable investigation of the carbon-iron equilibrium diagram assigns definite temperatures to certain very important lines in the diagram, viz.: the eutectic temperature EB (Fig. 1) and the " near-eutectic " temperature E'B', but without indicating clearly enough the reasoning which warrants these assignments. These temperatures are of such primary importance that it is well to indicate the apparent gaps in the reasoning, in the hope that they may be filled in. In his diagram, Fig. 1, the point X and the lines B'D'HI represent the experimental results reached by Ruff and Goecke; 2 AB, AEB, and SE represent the liquidus, the solidus, and the solubility of the carbon in solid austenite in the absence of graphite according to Gutowsky,3 AB being also in accordance with Spiecker's data;4 ,S'E' the solubility of carbon in solid austenite in the presence of graphite according to Ruer and Iljin; 5 GS the line A3 after Goerens and Meyer;6 I and EBC the true eutectic line as inferred by Prof. Ruff from Gutowsky's data. B'D' is the carbon content found in cast-iron which had apparently saturated itself with carbon in the presence of the graphite of the enclosing graphite crucibles in which the determinations were made. From its straightness and its sharp inflection near 6.67 per cent. of carbon, the carbon content of * Professor of Metallurgy in Columbia University. 1 Metallurgie, vol. viii., pp. 456 to 464 and 497 to 508 (1911). 2 Idem, vol. viii., pp. 417 to 421 (1911). 3 Idem, vol. vi., pp. 731 to 743 (1909). 4 Idem, vol. vi., p. 524 (Wüst) (1909). 5 Idem, vol. viii., pp. 97 to 101 (1911). 6 Idem, vol. vii., pp. 307 to 312 (1910).

Nov 1, 1912

By Richard H. Terhune

The use of water-cooled breast-jackets or cinder-tap blocks is a great convenience in lead-smelting, even when siliceous slags are made. If the charges are at all basic it is almost imperative. Jackets of riveted wrought-iron or steel are expensive; those of cast-iron are liable to crack; those of bronze are costly and not durable, being easily penetrated by tapping-bars or destroyed by streams of matte impinging against them. To overcome these objections I introduced at the Hanauer works, in April, 1886, castjackets of steel, which have been in constant use since that time and are to-day as good as new. These jackets were made for us by the Chester Steel Castings Company, of Chester, Pa., at a cost of ten cents a pound at the works of that company. The metal is 5/8-inch thick, and the jackets were cored and tapped for l1/2-inch bushings, affording two large holes for the removal of dirt and incrustations. The same holes are used for feed- and discharge-water through 3/4-inch pipe. I hope the successful introduction here of cast-jackets of steel will lead to their more extended use in all branches of metallurgy where water-cooled surfaces are severely taxed, and where the size and thickness of the castings are not unfavorable to the production of a sound article, impervious to water and of high tensile strength.

Jan 1, 1889

By M. N. Shetty

LARGE copper whiskers (-100 p) of 11111 orientation were tested in a floor-model Instron testing machine, at liquid nitrogen temperature. (Testing methods will appear elsewhere.) Whiskers deformed by twinning after some initial deformation. A load-elongation curve at the onset of twinning is reproduced in Fig. 1. Twinning was confirmed by taking a back-reflection Laue picture, using a slit colli-mator, which showed distinct splitting of reflections. The tensile stress reached just before twinning is about 1.4 x 107 g per sq cm (-7.0 x106 g per sq cm—resolved shear stress) which drops to 1.2 x107 g per sq cm (-6 x 106 g per sq cm—resolved). This twinning stress is about five to ten times larger than the value for bulk single crystals of copper deformed at 77°K (-106 g per sq cm—resolved). Twinning models based on Cottrell-Bilby's pole mechanism are discussed in detail by Venables.' In the present work a mechanism based on the idea of failure of a Lomer-Cottrell barrier by recombination will be proposed. An L-C barrier may fail either by recombination or by dissociation.3 Fig. 2 provides the necessary information. It shows that the stress necessary to break such a barrier is about 1.8 x 107 g per sq cm by recombination and 4 x 107 g per sq cm by dissociation at 77°K. The twinning stress reached by whiskers is comparable to the stress level required for failure of an L-C barrier by recombination. (Stroh himself points out that his calculations should not be taken too literally.) We consider a segment of the L-C dislocation which has recombined (AB in Fig. 3) over a length to form the total dislocation which then glides in the

Jan 1, 1965

By L. F. Pease, J. H. Brophy

A phase diagram for the Ta-Zr system is presented. The system is of the minimum-melting point type with the 0-zirconium phase decomposing monotectoidally at 785°C and 95.5 at. pct Zr. The minimum solidus temperature is 1875°C and the temperature of the top of the monotectoid loop is 1775°C. Techniques employed included X-ray diffraction and fluorescmce, electron microprobe analyses, diffusion couples, metallography, and melting-point measurements. Errors due to interstitial solutes and in melting observations are particularly common in this system, and their occurrence is discussed. SEVERAL versions of the Ta-Zr phase diagram have been reported in the literature.lm7 Williams et al.' report a diagram of the minimum-melting point type with a monotectoid reaction at 800°C and 12 wt pct Ta. The minimum in the solidus occurs at 1820°C and 25 wt pct Ta, while the top of the monotectoid gap is located at 1780°C and 80 wt pct Ta. The experimental techniques employed were metallography, electrical resistance variation with temperature, dilatometry, X-ray diffraction, and direct observation of melting by the technique of Pirani and ~lterthum.' Experience in the Nb-Zr phase diagram has shown that small changes in the interstitial content can cause large shifts in the positions of the phase boundaries. Small amounts of inter -stitials can cause similar changes in the Ta-Zr system and may be responsible for the wide variations in the phase diagrams previously reported.'-' The authors15 have found that alloys containing 0.75 wt pct 0 and 1.0 wt pct Ni with tantalum contents from 19 to 85 at. pct often contain a lamellar or cellular precipitate after annealing above 1400°C. This precipitate is very similar to that reported by pollack,12 Ralls," and Donlevy17 for the Ni-Zr system. In the present investigation, a wider variety of experimental techniques and improved alloy purity were applied to the resolution of errors in diagrams for this system as they now appear in the literature. New results have been obtained in the areas of alloy homogeneity and purity. Errors in the common techniques of direct melting observation in binary alloys have been demonstrated. In the commercially important high-tantalum region, the more accurate metallographic method of solidus determination has been employed. EXPERIMENTAL PROCEDURE Nominal analyses of the materials employed are given in Table I. The zirconium was low hafnium reactor grade iodide crystal bar, and the tantalum was in the form of high-purity sheet. Powders were impossible to use because of gas content. Alloys were melted on a water-cooled copper hearth, with a thoriated tungsten-tipped nonconsumable electrode in 2/3 atm of Zr "gettered" argon. Alloys were

Jan 1, 1963

Discussion of the paper of R. H. RICHARDS and BOYD DUDLEY, JR., presented at the New York meeting, February, 1915, and printed in Bulletin No. 97, January, 191.5, pp. 67 to 72. R. H. RICHARDS, Boston, Mass.-I believe that the manner of working for efficiency in almost all lines is to study the conditions of highest efficiency, and then to measure what is being clone. We can then see how near we have approached the highest efficiency. Spigots in practice often use many times the water theoretically needed. There are places where that is necessary for safety reasons. There are, however, places where it is unnecessary, and in these places it seems to me that this work of Mr. Dudley's will be a great help to the mill man to arrive at the greatest economy of water and highest efficiency. ALBERT R. LEDOUX, New York, N. Y.-A good many years ago I received a telegram from that distinguished engineer, Hamilton Smith, which simply said in substance: "I have discovered that liquids will flow faster from a square orifice than from a round orifice of the same area, under the same head." I wondered why he sent me the telegram, but some time afterward he told me that he had been making experiments along that line in Montana; that he thought the discovery was interesting

Jan 5, 1915

By Henry Howe

THIS paper is a discussion of the extremely valuable one of Mathewson and Phillips, The Recrystallization of Cold-Worked Alpha Brass on Annealing,1 which not only gives us a wealth of important data reached with great intelligence, but also shows both uncommon powers of imagination and a perfectly fair spirit. Let me try to analyze some of their results, and to enunciate some of the laws to which these results point. For brevity I refer to them as "The Authors." The page numbers in parentheses refer to their paper. 1. The Visible Aspects of Recrystallization.-Plastic deformation in a single direction, as in cold-rolling, draws the grains out in that direction, that is, inequiaxes them, without destroying their apparent individuality. Each grain seems to endure the drawing out without changing either its volume or its orientation materially, for the etching tint of each grain seems to be as uniform after as before the drawing out, save for the "etch bands,"2 shown in Figs. A to D of the Authors' Plate I. As the drawn-out metal is heated progressively, on reaching a certain "disintegration temperature" these old grains seem to break up, probably into submicroscopic fragments, and this apparent disintegration is followed by a coalescence of these fragments, so that their number decreases and their size increases, till they may become very much coarser than before the drawing out. Ruder3 coarsened the grains of silicon steel in this way till single grains reached an area of 50 cm. (7.75 sq. in.). The deformation itself probably breaks each grain up into many very small fragments, but the fact that each grain continues to have a uniform etching tint different from that of its neighbors indicates that these fragments retain the initial common orientation of the grain. The apparent disintegration which we observe, then, is rather an abandonment of community of orientation for individuality of orientation, by the fragments formed earlier during the deformation. Hence we

Jan 10, 1916

COUNCIL OF SECTION DELEGATES Jack A. Criehton. Chairman Allen T. Cole. Vice Chairman M I. Signer, Secretary EXECUTIVE COMMITTEE W. C. Leonard, North Pacific W. K. Beck, Cleveland W. W. Leonard, Southwest Texas

Jan 1, 1952

By R. E. Powers, E. H. Kinelski, H. A. Morrissey

A group of 17 American blast-furnace sinters, an American open-hearth sinter, an American iron ore, and a Swedish sinter were used to evaluate testing methods adapted to appraise sinter properties. Statistical calculations were performed on the data to determine correlation coefficients for several sets of sinter properties. Properties of strength and dusting were related to total porosity, slag ratio, and total slag. Reducibility was related to the degree of oxidation of the sinters. THIS report to the American iron and steel industry marks the completion of a 1949 survey of blast-furnace sinter practice sponsored by the Subcommittee on Agglomeration of Fines of the American Iron & Steel Institute. The use of sinter in blast furnaces, sinter properties, raw materials, and sinter plant operation have been reported recently.1,2 After preliminary research and study," test procedures were adapted to appraise the physical and chemical properties of sinter to determine what constitutes a good sinter. During the 1949 to 1950 plant survey each plant submitted a 400-lb grab sample to research personnel at Mellon Institute, Pittsburgh, Pa. A 400-lb sample was also submitted from Sweden. In addition, 2 tons of group 3 fines iron ore were obtained from a Pittsburgh steel plant. The following tests were performed on the iron ore sample and on the 19 sinter samples: chemical analysis; impact test for strength and dusting; reducibility test; surface area measurements, B.E.T. nitrogen adsorption method; S.K. porosity test; Davis tube magnetic analysis; X-ray diffraction analysis for magnetite and hematite; and microstructure. Results of these evaluations are discussed in this paper and supply a critical look at testing procedures used to determine sinter quality. Sinter Tests and Results Each 400-lb grab sample of sinter was secured at a time when it was believed to represent normal production practice at each plant. It was not possible to use the same sampling procedures throughout the survey; consequently samples were taken from blast-furnace bins, cooling tables, and railroad cars. These were very useful for evaluation of test methods, since they were obtained from plants with widely divergent operations. With the exception of Swedish sinter and sinter sample N, which were produced on the Greenawalt type of pans, all survey sinters were produced on the Dwight-Lloyd type of sintering machines. Sinters submitted for test were prepared in identical manner by crushing in a roll crusher (set at 1 in.), mixing, and quartering. To secure specific size fractions for tests, one quarter of the sample was crushed in a jaw crusher and hammer mill to obtain a —10 mesh size. The remainder was screened to obtain specific size fractions. The group 3 fines iron ore was dried and screened and samples were taken from selected screen sizes to be used for various tests. Prior to testing, each ore sample except the —100 mesh fraction was washed with water to remove all fine material and was then dried. This iron ore, a hematitic ore from the Lake Superior region, was used as a base line for comparing results of tests on sinters. The iron ore did not lend itself to impact testing, since it was compacted rather than crushed in the test, and no impact tests are reported. However, the iron ore was subjected to all remaining physical tests to be described. Chemical Analysis: Table I presents chemical analyses performed on the survey sinter samples. Included in this table are data obtained from determination of FeO and the slag relationships: CaO + MgO and total slag (CaO + MgO + SiO, SiO2 + Al2o3 + TiO2). The percentage of FeO was used as an indication of the percentage of magnetite in the sinter. It was believed that slag relationships could be correlated with sinter properties. During initial determination of FeO great disagreement arose among various laboratories, both as to the results and the methods of determining values. Table I lists the values of FeO resulting from the U. S. Steel Corp. method of chemical analysis,' which reports the total FeO soluble in hydrochloric and hydrofluoric acids (metallic iron not removed) with dry ice used to produce the protective atmosphere during digestion. Use of dry ice was a modification required to obtain reproducible results. In this method, the iron silicates and metallic iron are believed to go into solution and are therefore reported as FeO. This is important, for in the study of the microstructure of sinters, glassy constituents suspected of containing FeO as well as crystallized phases of undetermined identity which may also contain FeO have been observed. Strength Test by Impact: In evaluating sinter quality, one of the properties stressed most by blastfurnace operators is strength. This strength may be described as the resistance to breakage during handling of sinter between the sinter plant and the blast-furnace bins. It is also the strength necessary to withstand the burden in the blast-furnace. After

Jan 1, 1955

By W. M. Baldwin, J. T. Brown

The effect of hydrogen on the ductility, c, of SAE 1020 steel at strain rates, i, from 0.05 in. per in. per rnin to 19,000 in. per in. per rnin and at temperature, T, from +150° to —320°F was determined. The ductility surface of the embrittled steel reveals two domains: one in which and the other in which The usual "explanations" of hydrogen embrittlement are in accord with the first of these domains only. THE purpose of this investigation was a fuller A characterization of this of the investigation effects of varying temperature and strain rate on the fracture strain of hydrogen-charged steel. To be sure, it is known that low and high temperatures remove the embrittlement that hydrogen confers upon steels at room temperature,1 * see Fig. la and b, and that high strain rates have a similar effect,'-' see Fig. 2a, b, and c. However, the general effect of these two testing conditions on the fracture ductility of hydrogen-charged steels is not known, i.e., the three-dimensional graphical representation of fracture ductility as a function of temperature and strain rate is not known—only two traverses of the graph are available. The need for such a graph is not pedantic. To demonstrate this point, Fig. 3a, b, and c shows three of many three-dimensional graphs, all possible on the basis of the two traverses at hand. The important point (as will be developed in the Discussion) is that each of them would indicate a different basic mechanism for hydrogen embrittlement. It will be noted that the four types of ductility surfaces in Fig. 3a, b, and c may be characterized as follows: Material and Procedure Tensile tests were made at various temperatures and strain rates on a commercial grade of % in. round SAE 1020 steel in both a virgin state and as charged with hydrogen. The steel was spheroidized at 1250°F for 168 hr to give the unembrittled steel the lowest possible transition temperature. The steel was charged cathodically with hydrogen as follows: The specimen was attached to a 6 in. steel wire, degreased for 5 min in trichlorethylene, rinsed with water, and fixed in a plastic top in the center of a cylindrical platinum mesh anode. The assembly was placed in a 1000 milliliter beaker containing an electrolyte of 900 milliliters of 4 pct sulphuric acid and 10 milliliters of poison (2 grams of yellow phosphorous dissolved in 40 milliliters of carbon disulphide). A current density of 1 amp per sq in. was used which developed a 4 v drop across the two electrodes. All electrolysis was carried on at room temperature. Temperatures for tensile tests were obtained by immersing the specimens in baths of water (+70° to + 150°F), mixtures of liquid nitrogen and isopen-tane (+70° to —24O°F), and boiling nitrogen (-240" to-320°F). Specimens were tested in tension at strain rates of 0.05, 10, 100, 5000, and 19,000 in. per in. per min. The 0.05 and 10 in. per in. per rnin strain rates were obtained on a 10,000 lb Riehle tensile testing machine, the 100 in. per in. per rnin rate on a hydraulic-type draw bench with a special fixture, and the 500 and 19,000 in. per in. per rnin rates on a drop hammer. The fracture ductility of hydrogen-charged steel at room temperature and normal testing strain rates (-0.05 in. per in. per min) is a function of electro-lyzing time, dropping to a value that remains constant after a critical time.'* Under the conditions of • The hydrogen content of the steel continues to increase with charging time even after the ductility has leveled off to its saturated value.' this research the saturated loss in ductility occurred at approximately 30 min, see Fig. 4, and a 60 min charging time was taken as standard for all subsequent tests. After charging the steel with hydrogen, the surface was covered with blisters. These have been described by Seabrook, Grant, and Carney.' The original diameter of the specimen was not reduced by acid attack, even after 91 hr. Results The ductility of both uncharged and charged specimens is given as a function of strain rate in Fig. 5, and as a function of temperature at four different strain rates in Fig. 6. These results are assembled into a three-dimensional graph in Fig. 7. It is seen that the locus of the minima in the ductility curves of the charged steels divides the ductility surface into two domains. At temperatures below the minima,

Jan 1, 1955

By K. Leutwyler, H. L. Bigelow

Jan 1, 1966

By C. C. Miller, A. R. Belyea, C. H. Herty, E. B. Burkart

The removal of sulfur from steel has been studied by many investigators, but the quantitative relationships between the factors involved have not been determined. This is undoubtedly due to the number of variables encountered in practice, an attempt to study any one reaction or relation being affected by other reactions the relative importance of which cannot be estimated. The factors that affect the extent of removal of sulfur in the basic open-hearth process are generally considered to be: 1. Basicity of the slag: (a) Iron oxides in the slag; (b) carbon in the metal or carbide in the slag; (c) temperature. These factors affect the reactions: FeS + CaO = CaS + FeO FeS + CaO + C = CaS + CO + Fe. 2. Amount of sulfur in the gas. 3. Amount of manganese in the metal. The factors which affect the rate of removal of sulfur include, in addition to these: 4. Fluidity of the slag: (a) Normal changes in fluidity with temperature; (b) changes in fluidity because of the addition of special reagents such as fluorspar. 5. Agitation of the bath. Within the past two years, two papers have been presented dealing with the influence of sulfur in the gas on slag and metal. Nead' has shown that if a gas high in sulfur be used for heating, the metal and slag will absorb sulfur. Whitely2 concluded from his experiments that if a

Jan 1, 1925

By H. T. Bowman

For more than 80 years the Bessemer process has depended upon the ability, skill, and judgment of the blower, although as early as the I860's it was recognized that the process would benefit by some type of instrumental contro1.l IIowever, instruments with sufficient recording speeds did not exist, so the end-point determination was always dependent upon the blower's eye. This placed an obstacle in the way of precise experimental work, because of the absence of the necessary records and reference points as reported by Work.2 The use of the photocell provided the instantaneous record of the blow that made this experimental work possible and provided more scientific control for the process as discussed by Graham,3 A brief description of the progress of the blow will illustrate the recording function of the instrument. The silicon in the iron is being oxidized during the first minutes of the blow, as pointed out by Henning4 in a table showing the order of metalloid elimination. The product of this oxidation is a solid that remains in the converter, so there is virtually no flame during this part of the blow. This low flame luminosity is illustrated by the flame recording shown in Fig. I, where the silicon blow is plainly marked. The dull flame of the silicon blow gradually gives way to the brilliant carbon flame as the increasing quantities of carbon monoxide formed inside the converter burn to dioxide upon contact with the atmosphere above the vessel. When the carbon reaches some low value under 0.20 per cent, there is insufficient menoxide formed to maintain the dioxide flame, so its intensity drops. Throughout the flame drop carbon continues to burn, until at some value around 0.05 per cent an arrest occurs in the recorded drop. This point has been designated as the end point. The period of time from this end point until the vessel is turned upon its side and blowing has stopped has been called the afterblow. This afterblow is used as a measure of the degree of metal oxidation, and uniformity demands that it be controlled within narrow limits. Iron and blowing conditions are likely to change several times during a turn, necessitating corresponding changes in end-point control. It is the purpose of this paper to discuss these changes, the factors that make them necessary, and their bearing upon the quality of steel. Carbon-FeO Relationship In the Bessemer process oxidation relationships are precise. Fig. 2 shows a graph of the carbon-FeO relationship. The familiar "bomb-test" method, described by Mccutcheon and Rautio,5 was used for obtaining these and all other dissolved FeO values herein reported, all tests being taken from the converter before deoxidation unless otherwise noted. All tests of 0.10 per. cent carbon and above were obtained from metal blown for duplexing. McGinley and Woodworth6 reported iron oxide values for blown metal, but their tests were obtained by a . different method than were those

Jan 1, 1942

By H. T. Bowman

For more than 80 years the Bessemer process has depended upon the ability, skill, and judgment of the blower, although as early as the I860's it was recognized that the process would benefit by some type of instrumental contro1.l IIowever, instruments with sufficient recording speeds did not exist, so the end-point determination was always dependent upon the blower's eye. This placed an obstacle in the way of precise experimental work, because of the absence of the necessary records and reference points as reported by Work.2 The use of the photocell provided the instantaneous record of the blow that made this experimental work possible and provided more scientific control for the process as discussed by Graham,3 A brief description of the progress of the blow will illustrate the recording function of the instrument. The silicon in the iron is being oxidized during the first minutes of the blow, as pointed out by Henning4 in a table showing the order of metalloid elimination. The product of this oxidation is a solid that remains in the converter, so there is virtually no flame during this part of the blow. This low flame luminosity is illustrated by the flame recording shown in Fig. I, where the silicon blow is plainly marked. The dull flame of the silicon blow gradually gives way to the brilliant carbon flame as the increasing quantities of carbon monoxide formed inside the converter burn to dioxide upon contact with the atmosphere above the vessel. When the carbon reaches some low value under 0.20 per cent, there is insufficient menoxide formed to maintain the dioxide flame, so its intensity drops. Throughout the flame drop carbon continues to burn, until at some value around 0.05 per cent an arrest occurs in the recorded drop. This point has been designated as the end point. The period of time from this end point until the vessel is turned upon its side and blowing has stopped has been called the afterblow. This afterblow is used as a measure of the degree of metal oxidation, and uniformity demands that it be controlled within narrow limits. Iron and blowing conditions are likely to change several times during a turn, necessitating corresponding changes in end-point control. It is the purpose of this paper to discuss these changes, the factors that make them necessary, and their bearing upon the quality of steel. Carbon-FeO Relationship In the Bessemer process oxidation relationships are precise. Fig. 2 shows a graph of the carbon-FeO relationship. The familiar "bomb-test" method, described by Mccutcheon and Rautio,5 was used for obtaining these and all other dissolved FeO values herein reported, all tests being taken from the converter before deoxidation unless otherwise noted. All tests of 0.10 per. cent carbon and above were obtained from metal blown for duplexing. McGinley and Woodworth6 reported iron oxide values for blown metal, but their tests were obtained by a . different method than were those

Jan 1, 1942

By P. T. Allsman

INTRODUCTION The honor of being the recipient of the Mining Society's Daniel C. Jackling Award for 1966 imposes on me the responsibility to search for the subject that I would be best qualified to discuss. It seems that my experience in the mineral industry — nearly 15 years in private and 30 years in public employment — should uniquely qualify me to comment upon the relationships between the mining industry, mineral engineering as a profession, and government, and the changing economic, technologic, political and social changes that dictate their relationships. Such conditions, the increasing knowledge of the world mineral resource base, the greater demands of an expanding population with a rising standard of living, shall be evaluated with respect to our profession — mineral engineering. In all of these forty or so years, I have been in close touch with many phases of the mineral and energy resource industries, especially those of the United States. Particularly during the past 10 years, I have had a ringside seat at the "goings on" in Washington. During all of this period I have observed and analyzed many of the problems of the industry and its relations with the government. During the past few years, I have had increased opportunity for doing research and have found a need to learn something about the mathematical techniques that are undergoing such a revival since electronic computers were developed. One of these techniques is multivariate analysis, which is a system for correlating a large number of complex variables. By applying this technique to the seemingly chaotic present-day situation, there emerges a course of steady improvement in the minerals resource industries that wars, depressions, and political strife have failed to obstruct for long. In short, I advocate a need for new concepts in mineral engineering to cope with the changes, pos- sibly adding many more specialized areas on one end of the spectrum, and broad engineer-generalist approaches at the other. The meeting place shall be where the intricate mineral resource problems at the frontier of knowledge merge into the socio-techno-logical problems of the world. HISTORICAL INVOLVEMENT OF GOVERNMENT IN MINERAL RESOURCE PROBLEMS Involvement of government in mineral resource problems undoubtedly is as old as government itself. But passage of the Mining Act of 1866, superseded by the Act of 1872, was the first major entry of our Federal Government into the problems of mining. Passage of the law was necessary to resolve many conflicting claims and disputes in mining. The General Mining Law of 1872 and the Mineral Leasing Laws of 1920 apply to millions of acres of public lands and to certain privately owned land on which the mineral rights have been reserved to the Federal Government. The extensive involvement of government in the mineral industry business today often comes as a shock to the mineral engineer who has begun to climb the ladder to the top in his company. He is often poorly prepared to cope with the situation and becomes frustrated and even hostile. Better knowledge of the role of government perhaps would ease his situation. In our political system, private industry is responsible for producing minerals. To make certain that the production is adequate for a peace-time economy, and to guarantee the Nation's security in an emergency, the Federal Government finds it expedient to develop policy and engage in regulatory, educational, and research activities. A few examples will illustrate the varied role of government in relation to mineral problems. In varying degrees many agencies of the Executive Branch of Government have responsibilities that influence the functioning of the mineral and energy industries. In addition, of course, Congress, the Judiciary, and State and local governments exercise great influence. The Department of the Interior is primarily responsible for activities to promote the development and conservation of mineral and fuel resources, and the

Jan 1, 1967

By W. L. Fink, L. A. Willey

During the war there was introduced a new higher strength aircraft alloy designated 75S.1,2,3 The properties of this alloy assure extensive applications in both military and commercial aircraft. It is therefore important to understand its limitations as well as advantages. The properties of 75.5 alloy in the heat-treated tempers, like those of many other aluminum alloys, are affected by the rate of quenching. In general, low quenching rates tend to cause low strengths and to adversely affect the resistance to corrosion. Commercial quenching procedures are usually sufficiently rapid to permit the development of maximum properties. However, in the center of heavy sections, such as large rolled and extruded shapes, the quenching rates may not be rapid enough to develop maximum strength or resistance to corrosion. The investigations of 75s alloy described herein reveal the most critical range of temperature and the effects of quenching sheet and extrusions at different rates through that temperature range, on the tensile properties and resistance to corrosion. Procedure Preparation of Specimens Sheet specimens (3 in. by 9 in.) were prepared from a commercial lot of 75s "as rolled" sheet (0.064 in. thick). The composition4 was as follows: Weight Percentage Cu Mn Mg Zn Cr A1 with Normal Impurities 1.64 0.16 2.58 5.66 0.27 Remainder The specimens employed for the determination of the time-temperature relations during quenching of sheet were prepared by the following procedure: the hot junction of a 28-ga. iron-constantan thermoelement (asbestos insulated) was brazed to a thin strip of aluminum which was in turn brazed into the end of a 3/16-in. id by %-in. od by 30 in. long aluminum protection tube. Before brazing, the tube was flattened to 0.064-in. thickness over the junction and adjacent lead wires for a distance of I 1/2 in. The flattened end of the tube was fitted into a slot cut from one edge to the center of the 3-in. by 9-in. by 0.064-in. sheet and brazed into place. The brazed joint was dressed to the thickness of the sheet and the entire specimen buffed to approximately the brightness of "as rolled" material. Because of the brazing operations required, these specimens were prepared using 3S alloy. For the investigation of quenching rates in heavy sections, there were used 75s extrusions which had compositions similar to that of the sheet. The specimens consisted of 14 in. lengths of 3i-in., 2-in., 3-in, and 4-in. diam cylindrical rods and a roughly rectangular extruded section which was approximately 4 in. by 7 1/2 in. Thcrmocouple~ were peened into the bottoms Of .1/8-in. diam wells drilled into one end and parallel to the axis to a depth of

Jan 1, 1949

By G. D. Gemmell

Effects of solid-sdutidn alloying with titanium, molybdenum, and tungsten at concentrations up to 10 pct on the strength of pure columbium at elevated temperatures (mainly 2000°F) have been investigated by means of creep-rupture, hot-tensile, and hot-hardness testing and recrystallization studies. ThIS paper presents some results from the initial part of a study of the effects of alloying on the high-temperature strength properties of columbium. The elevated-temperature strength characteristics of pure columbium were first studied. Binary alloys of columbium with titanium, molybdenum, and tungsten containing 1, 5, and 10 pct of the solute elements were chosen on the basis of their high melting points, their known solid solubility in columbium, and results of separate oxidation-resistance studies of columbium alloys. EXPERIMENTAL PROCEDURE All the materials used were of highest purity. A typical analysis of the columbium is shown in Table I. Compositions of the alloys are also given in Table I. To evaluate the strength properties of pure co-lumbium and the alloys at elevated temperatures, creep-rupture, hot-tensile, and hot-hardness testing was done on recrystallized material. To prepare the pure metal and the alloys for these tests, 1- 1b buttons were made in a water-cooled copper crucible, inert atmosphere, tungsten arc furnace. Tapered ingots, 3 in. long, were made from these buttons by a skull-casting technique and these were machined to 1/2 in. diam, swaged to 50 pct reduction (pure columbium at room temperature, alloys at lowest temperature possible without cracking, generally in range 1100" to 1800°F) and heated in vacuum (lo-' mm Hg) for 16 hr at 2550°F for re-crystallization and homogenization. The resulting grain diameter was 0.1 to 0.3 mm. The 10 pct Mo alloy casting was not successfully swaged at temperatures up to 1800°F without cracking and was not included in the test program. Creep-rupture testing was done at constant load in vacuum on cylindrical specimens of 0.16 in. diam, using Instron capsules. The pressure at test temperatures was less than 10-1 mm Hg. Hardneas readings taken on the test specimen before and after testing were used as a check on possible gaseous contamination. Hot tensile tests in vacuum on cylindrical specimens of 0.125 in. diam were also made with Instron equipment at a strain rate of 0.067 min.-l. Hot-hardness measurements were taken with a unit constructed at the Du Pont Experimental Station. The test piece, supported on an alumina anvil, and the molybdenum indenter shaft with sapphire tip is heated in a platinum-wound furnace. The load applied to the pyramid indenter is measured by strain gages attached to a proving ring located outside the hot zone. In the measurements reported here the load was I kg. The tester operates in a vacuum of about 10"5 mm Hg and is capable of temperatures up to 1400°C.

Jan 1, 1960

By N. Jaffee, J. E. Dorn

An activation energy of 27,400 5 1000 cal per mole was obtained for the creep of poly crystaLline aluminum over the temperature range of 273° to 350°K, at strains varying from 0.003 to 0.230. Stresses varied fronz 2250 to 6000 psi, strain rates from 0.1145 x 10-5 to 29.5 x 10~s min.-1. A strain temperature-compensated time correlatzon was oblained indicating that the structure was depedent solely upon the strain at a given stress; X-ray diffraction analyses and tensile tests on precrept specimens verified this. PREVIOUS investigations1 have revealed that the apparent activation energies for creep of high-purity polycrystalline aluminum are insensitive to the applied stress, strain, and strain rate. On the other hand, the apparent activation energy is dependent on the temperature1,2 as shown by the data reproduced in Fig. 1. Each plateau of this curve is associated with a unique rate-controlling dislocation mechanism for thermally activated creep. It is now very well-established that over the high-temperature range, where the activation energy is about 35,500 cal per mole, the creep rate is controlled by the dislocation climb mechanism. 3 Over the intermediate range of temperatures, from about 260° to 370°K, another unique activation energy, namely 28,000 cal per mole, is obtained. Current evidence strongly supports the contention that cross slip is the rate controlling mechanism for creep in this case: 1) Crystal recovery can occur by a number of mechanisms prominent among which are climb and cross slip. Astrom,4 using the Borelius micro-calorimeter, reported rapid crystal recovery of cold-worked polycrystalline A1 at 340° to 370°K giving an activation energy of 28,000 cal per mole and additional recovery at 455° to 478°K giving an activation energy of 3 6,000 cal per mole. Whereas the latter recovery process was clearly associated with the dislocation climb mechanism, the former, 28,000 cal per mole process could have arisen as a result of the cross-slip mechanism. 2) Single crystals of high-purity A1 favorably oriented for octahedral glide exhibit an activation energy for creep of about 3400 cal per mole over the range from 0° to 400°K and that of about 28,O:O cal per mole over the range from 600° to 775°K . Whereas the lower activation energy process is accompanied by the development of sharp slip-band traces, the 28,000 cal per mole process was uniquely characterized by extensive cross slip. 3) Theoretical calculations by Seeger and schoeck6 suggest an apparent activation energy for cross slip in A1 of about 24,000 cal per mole and another theoretical estimate by Friedel 7 gives the observed 28,000 cal per mole as the theoretical activation energy. It is therefore consistent with this evidence to, at least tentatively, ascribe the 28,000 cal per mole creep process in A1 to the operation of cross slip as the rate controlling mechanism. Although creep has been rather well-explored in the dislocation climb range, very little, excepting perhaps the activation energy, is known about creep in the cross slip range. This investigation was undertaken, therefore, to reconfirm the activation energy for creep in polycrystalline A1 in the intermediate temperature range and to study the strain-time relationship for creep at a constant stress in the cross slip region. EXPERIMENTAL PROCEDURE AND TECHNIQUE The three types of high-purity A1 alloy specimens described in Table I were used in this investigation. Specimens were milled from 0.100 in. thick cold-rolled sheets with their tensile axes in the rolling direction following which they were given a recrys-tallization and grain growth heat treatment at temperatures well above those which were subsequently employed in the creep tests.

Jan 1, 1962