Search Documents

By AIME AIME

ON May 5, the Washington, D. C., Section, A.I.M.E., devoted its meeting to the many-sided and perplexing question of mineral stock-piling for peace. Opening the symposium, Harry J. Wolf, of the War Production Board, outlined the problem under six heads: (1) Technical. Mechanical, chemical, or metallurgical importance of specified materials, emergencies that might arise, relative scarcity, and critical value of stock piles during emergencies. (2) Economic. Cost to Government, influence of Government stocks on commercial relationships and markets, effect of availability of items as a con¬structive influence on industry, Administration policies now and during postwar period. (3) Legislative. Need for immediate legislative action, need for legislation on postwar conditions as well as on current requirements, a constructive basic policy to prevent political manipulation. (4) Military. Consideration of re¬quirements and supplies bearing on national safety and needed for manufacture of equipment, and adequate reserves of scarce materials for research or experimentation by military agencies. (5) International. Interests of the United Nations in contradistinction to those of the United States; effects of nonisolation policy on nature, location, and administration of stock piles. (6) Negative stock-piling. Question of United Nations' legislation to prevent stock-piling by Axis nations after the war and who shall purchase stock-pile materials and during what periods.

Jan 1, 1943

By L. W. Rowe, S. S. Cole

A laboratory bench scale unit is described whereby finely divided chlorinatable residues are held for a short period by a restraining bed of a coarse-grained ore of comparable composition to permit 'flash' chlorination of the high surface area powder. Results on chlorinating a finely divicled titania residue using rutile sand as the restraining bed showed that 92 pct utilization of chlorine and equivalent conversion of TiO2 in the fine residue to Ticl4 were attained with a dust loss of about 3 to 4 pct and an equivalent amount of ch1om'nation of the titanium values in the restraining bed. THE chlorination of coarse grain titaniferous ores; i.e., 20 to 150 mesh sizes in fluidized beds is practiced commercially.' One effective method found for the chlorination of a very fine material in a fluidized bed is the "flash" chlorination technique.' By charging the finely divided charge material into the bottom of an established bed of optimum sized rutile, ilmenite, titanium beneficiate, or even an inert material such as sand, chlorination occurs before the dust can pass through the bed. The major requirement is that the bed be less chlorinatable than the charge. In this process, the charge consists of a finely divided (between one and 50 µ) titania residue obtained from a titaniferous ore beneficiation process. The charge is blended with a 20 pct wt basis addition of 20 to 60 .mesh size low volatile coke (to minimize hydrogen chloride formation) and fed to the bottom of the bed with the chlorine gas stream. A ball check device is used to permit entry of the charge and prevent the bed from discharging when the gas flow is cut off. The coarse pieces of coke serve to reduce compaction in the charge mixture and permit sat]sfactory feeding without plugging or jamming. Feed and gas rates are adjusted to provide for complete reaction of the charge material, with 90 to 95 pct chlorine efficiency, and maintain a gas flow in the range of 0.4 to 0.6 ft per sec. The equipment consisted of a 3-in. diam mullite tube enclosed in an electric furnace. A bow-shaped 3/4 in. Saran tube fed the charge from an air lock type of feed hopper (to prevent the escape of the chlorine gas into feed bin) to the bottom of the bed. The charge rate was set by providing a small awiliary hopper below the feed hopper where a weighed portion of the charge could be discharged in a specified time interval into the main chlorine stream. The chlorine rate was measured by a flowmeter. The reaction tube was filled with a bed of Australian rutile ore, this restraining bed serving two purposes; i.e., it rapidly heated the fresh charge to the reaction temperature and retained the particles in the bed for a sufficient time for selective chlorination to proceed. Due to the fine particle size and open, porous structure of the charge, this reaction was almost instantaneous, and, with proper adjustment of feed and gas rates, very little fine material passed through the bed without reacting and only a very small fraction of the restraining bed was chlorinated. A typical reaction procedure was to fill the bench scale fluidized bed unit with a 1 kg charge of Australian rutile ore analyzing 95.5 pct TiO2, 0.6 pct FeO, a beach sand deposit 40 to 150 mesh size. When fluidized, the bed was approximately 2 ft in depth. The ore was fluidized with a 1:l mixture of chlorine and nitrogen at a rate of 0.40 ft per sec. This gas mixture was necessitated by the comparatively short bed depth; a larger unit, with a deeper bed, could be fluidized with chlorine alone without significant free chlorine loss. Feed rate was 8.0 g per min of beneficiated ilmenite analyzing 85.0 pct TiO2, 2.6 pct FeO plus 1.6 g per min of 20 to 60 mesh petroleum coke. The

Jan 1, 1962

By A. A. Smith, J. S. Smart

THE controlled amounts of phosphorus, arsenic, sulphur or selenium found in commercial coppers perform a variety of highly useful functions. Indeed, a large segment of modem copper technology is essentially dependent upon the presence of one or more of these elements. Consequently, the literature contains many references to their effects but the scope is broad and has been only partly covered. New data are presented herewith directed toward a better understanding of the basic behavior of these elements in copper, with particular emphasis on the composition range 0 to 0.05 per cent. These data are a part of a general program of research on the effects of impurities on the properties of oxygen-bearing and oxygen-free copper, other portions of which have been reported previously.1-2-3 Schematically, the behavior of individual elements is determined from measurements of conductivity and softening temperature,1, 2 and the binary alloys employed are synthesized from high-purity copper in order to eliminate interference from the effects of extraneous impurities. Alloys of selected composition were first prepared in the oxygen-free form by continuously casting the melts in the form of 3/8-in. diameter rod. Oxygen was added subsequently to portions of the alloys, either by remelting or by diffusion at 850°C. from a surface scale. Test wires were drawn one B. and S. number per pass, using four 30-min. 600°C. anneals at o.3125, 0.257, o.204 and o.162 in., and a final cold reduction of 95 per cent t0 0.081 in. Oxygen-bearing slugs made by remelting were hot-rolled to 5/16 in., drawn to 0.162 in., annealed for 30 min. at 600°C. and cold-drawn 95 per cent to 0.081inch. The alloys containing phosphorus, having been compounded very early in the program, were prepared in the form of 5/16-in. rod, and processed to wire with only the last three intermediate anneals listed above, all of these having been conducted in commercial nitrogen. In addition, the conductivity anneals on these alloys were also performed in the same atmosphere, and the small amount of oxygen present as an impurity in the gas resulted in some loss of accuracy at temperatures of 700° to 800°C., as will be shown later. Subsequently, the anneals for all oxygen-free alloys were conducted in hydrogen to prevent oxidation, and purified nitrogen was employed only for oxygen-bearing samples. All conductivity anneals were of one hour duration followed by a rapid quench in 10 per cent H2SO4. EFFECT OF PHOSPHORUS The widespread use of phosphorus as a deoxidant has resulted in universal appreci-

Jan 1, 1945

By Karl A. Bauer, Cornelis Bezemer

The deposition of calcium carbonate scale on surface and subsurface production equipment creates an operation problem in many oil fields. The formation water in which the carbonate-scale-forming components are initially dissolved becomes supersaturated with calcium carbonate as a result of the drop in pressure during production. The continuous flow of a supersaturated solution through the production equipment results in the growth of a dense layer of calcium-carbonate crystals. For a scale layer to be built up, the supersaturated formation water should contact the walls of the production equipment. The tendency for scale to be deposited, therefore, will be low, if the crude has a low water cut and if the water is finely dispersed in the oil. A scale problem will occur, if at a high water cut part of the water is present as free water. The rate of scale deposition will then be approximately proportional to the rate of free water production. Depending upon where the formation water becomes supersaturated, scale may be deposited in the flow line only, in both flow line and tubing, and in some cases even in the perforations and in the formation near the wellbore. In the South Sumatran fields (Indonesia) the main difficulties encountered due to the deposition of calcium-carbonate scale have been restriction of flow through tubings and flow lines, wear and abrasion of plungers and liners, and stuck plungers or wellhead valves. So far, the only methods of combating the *Presently associated with Brunei Shell Petroleum Co., Ltd.. Seria. scale problem have been routine acidizing and additional well pulling. As for the pumping wells, it was estimated that some 50 percent of the total well-pulling effort was directly attributable to scale deposition. The most promising alternative was to prevent the deposition of calcium carbonate scale by means of chemicals. Inorganic polyphosphates such as sodium hexametaphosphate and trisodium polyphosphate are known to retard the formation of scale by the "threshold action". They are adsorbed on specific faces of the crystal nuclei and thus prevent crystal growth, thereby stabilizing supersaturation. Polyphosphates are effective at very low concentrations ( a few ppm), and far less than stoichiometric quantities are required to keep the scaling ions in solution. Recent investigations on barium sulfate scale1 have confirmed this mechanism. The types of polyphosphate mentioned can be applied as concentrated aqueous solutions either squeezed into the formation, lubricated down the annulus or injected via macaroni string. Several squeeze jobs with polyphosphate solutions have been carried out in the South Sumatran fields, however, with disappointing results. Lubrication down the annulus and injection through a macaroni string were not considered attractive in this area because of the kind of equipment and the degree of supervision these techniques require. Polyphosphates are also available in a granular, glassy form, which, in contrast with the readily soluble types already mentioned, show an extremely low

Jan 1, 1970

By B. F. Oliver, F. Garofalo

Gas-metal heterogeneous reactions and zone-lrelting were sinultarneously employed to produce several high-purity irons with low interstitial contents in a levitating- zone melter. Successive zone-tneltitzg pusses were made in carious sequences of atmospheves which included prepuvified tank hy-drogeta, water vapor hydrogen, palladiuril-purified hydrogen, and vacuunm of 2 x 10-6 Torr. Different irons ranging in purity from 99.89 to 99.996 pct with residual curbon contents of 17, 8 to 10, and 3 to 5 ppm have been Drepared. No measuvable gradient in the residual carbon content was observed along the entire zone-melted length (6-10 in.) in I-ilz.-diameter bars. The absence of a carbon-concentration gradient in the solid indicates an apparent distvihution coefficient of 1, an unusual condition. Internal friction, solid-state extraction, and hot-hardness results indicate that the level of mobile carbon in a iron depends on the gas-metal heterogeneous reactions employed. Purification under an oxidizing atmosphere resulted in the immobilization of nearly all of the carbon present at leuels of 10 ppm or less. Continuation of purification in a reducing atmosphere veturued the carbon to a state of mobility which was aguin reversed by further purification in all oxidizing atmosphere. The immobilization of curbon at "vesidual levels " is believed to be associated with a strong interaction between carbon and oxygen atoms. frons with low carbon and nitrogen contetzts which did not exhibit a hot-hardness peak were produced after zone ynelting in vacuum. CARBON, nitrogen, and oxygen have strong and well-known effects on many properties of iron. These effects persist even at concentrations of 5 to 20 ppm. The intent of the present investigation was to establish procedures for the preparation of high-purity iron with concentrations of these elements in the range of 5 to 20 ppm and lower. The results reported here deal with the procedures employed to prepare high-purity iron, and with observations on the behavior of certain elements at "residual levels": particularly carbon. The details of the (levitating) zone melter in which the final purification steps are performed and the necessary control of the pertinent solidification variables have been described previously.1,2 MATERIALS AND PROCEDURES Commercial electrolytic iron was induction vacuum-melted and cast into 30-lb ingots. Melt additions and ingot analyses for carbon, oxygen, and nitrogen are noted in Table I. All ingots were melted in stabilized zirconia crucibles conditioned with one iron wash heat. Middle sections of the ingots were forged to 1-1/4-in. rounds, machined to 1-in.-diameter bars, then cut to 36-in. lengths. The zone-melting operations were performed on six iron bars (A to F) at a freezing velocity of 2 in. per hr with the freezing interface rotating2 at 200, 300, or 400 rpm. Liquid zones were passed through the bars in various sequences of atmospheres, Table 11, including prepurified tank H2, palladium-purified Hz, wet H2, and system vacuum of 2 x 1018 Torr. Wet-Hz atmospheres were obtained by bubbling palladium-purified Hz through water exhibiting a resistance of 3 megohms. This water was heated with a platinum-immersion heater and was degassed prior to use. Zone melting in a wet-HZ atmosphere resulted in oxidation of the elements which are oxi-dizable with respect to iron. Fine oxide particles were observed on the surface of the liquid zone, and were encased in the bar surface with the passage of the molten zone. Between each zone pass, the surface of the bar was removed by filing and deep etching; this was continued until the oxide formation ceased. The filings were magnetically separated and the residues analyzed by optical spectroscopy. These were especially high in silicon and manganese. Samples were removed from the iron bars, with few exceptions, following each zone-melting operation. A 0.08-in.-thick disc was cut with an Al2O3 cut-off wheel at a point 1/2 in. above the beginning of freezing. Material from each disc was used for hot-hardness measurements, resistivity-ratio measurements, and carbon, nitrogen, and oxygen analyses. Analyses for most other elements were

Jan 1, 1965

By A. C. Fieldner, W. A. Selvig

For purposes of coal classification it is desirable to know the composition and calorific value of the pure coal substance; that is, of the coal free from its ash-forming minerals. Two methods suggest themselves: (1) To free the coal from most of the ash-forming material previous to the analysis; and (2) to analyze the coal as received and calculate the analysis, with certain more or less arbitrary corrections, to the pure-coal basis. Calculation methods are obviously more apt to give correct results with low-ash than high-ash coals. With coals of unusually high ash it would appear preferable to remove, previous to the analysis, as much of the inorganic matter as possible, by float-and-sink or acid-treating methods. Effect of Ignition on Inorganic Constituents of Coal The need of corrections in calculating analysis to the pure-coal basis is due to the fact that the ash, as determined by ignition, is not the same, in either weight or composition, as the inorganic mineral matter in the coal. On ignition a number of changes occur in the coal such as loss of water of hydration of the shaly material, conversion of pyrite (FeS2) to ferric oxide (Fe203) with evolution of the sulfur as sulfur dioxide or possible fixation of more or less of the sulfur in the ash as calcium sulfate (CaSO4), and decomposition of calcite (CaC03) to calcium oxide (CaO). The amount of sulfur from pyrite which remains in the ash as calcium sulfate depends on the amount of calcite and pyrite in the coal. Certain coals high in both calcite and pyrite show relatively large amounts of sulfate sulfur in the coal ash. The determination of total carbon and hydrogen in coal includes, besides the organic carbon and hydrogen, the carbon of inorganic carbonates such as calcite, and the hydrogen of the water of composition of some of the ash-forming minerals. For detailed discussion of corrections proposed for calculations of coal analyses to the " pure "

Jan 1, 1930

By J. P. Carson

The works of the Tula Iron Company are in the Republic of Mexico, State of Jalisco, twenty-eight leagues southwest of Guadalajara, ten leagues northwest of the town of Sayula, through which passes the projected line of the Mexican National Railroad. Its geographical position would be about: latitude, 20' 10' N., longitude, 40 35' w. of Mexico City. The surrounding country is a rolling plateau, 6000 feet above the sea, enjoying the most magnificent climate in the world, the average temperature being about '70'. The works were commenced in 1850 by a company with very small capital, having not the least idea of the undertaking. They soon fell into the hands of the money-lenders, and after changing

Jan 1, 1879

By D. E. Stephenson. Discussion by R. G. K. Morrison, L. Obert

R. G. K. Morrison (Chairman, Dept. of Mining Engineering and Applied Geophysics, McGill University, Montreal, Que., Canada) - The discing of drill core has been a recognized pressure phenomenon for many years but only recently has an interest been taken in the mechanism involved. The work of Jaeger and Cook is referred to in the text. The authors have now advanced the study to establish, within certain loading limitations, a direct relationship between axial and radial stress at failure. This is an important contribution. In mines generally, where pressure conditions result in the spalling of openings, the faces of drifts and crosscuts, on scaling, usually show a concavity with respect to the opening very similar to the face of the drill hole after the separation of the stub. The same holds for shaft sinks. This suggests a similarity between the mechanism of the discing of core and that of the spalling of an opening, under pressure, to develop a more stable outline. The latter, commonly regarded as shear, is the most conspicuous type of failure observed in

Jan 1, 1967

By Otto H. Henry, Edward L. Badwick

Up to the present time, according to Hansen1 and Haughton,2 the constitution of the bismuth-indium system has not yet been published. The generally accepted value for the melting point of indium, as listed in most scientific journals and textbooks, is 155°C. Recently, however, H. M. Davis3 has determined a new melting point for indium of 257.3°C ± 0.1°C. Since bismuth has been used in preponderance as an alloying element in the majority of low-melting alloys, and indium has been used with considerable success in lowering the melting points of low-melting alloys,4,5 an interest has been developed in the application of these two metals, making a complete knowledge of the constitution of its alloys desirable. In this investigation, the melting point of indium reported by H. M. Davis has been found to be substantially correct. A value of 157.2°C ± 0.5°C was determined. The two eutectic compositions have been placed at 34 and 50 pct bismuth with their respective eutectic temperatures as 72.4'C ± 0.5°C and 90°C ± 0.5°C. The bismuth-indium phase diagram has been determined by thermal and microscopic analysis and is shown in Fig I. THERMAL ANALYSIS Granulated bismuth and indium shot, having a guaranteed purity of 99.99 and 99.95 pct, respectively, were melted in a carbon crucible by means of a laboratory heater. To minimize oxidation of the alloys, a heavy mineral oil (Nujol) having a high flash point was used. A platinum-platinum rhodium thermocouple 0f fine wire encased in a thin-walled Pyrex glass tube, about 1/8 in. in diameter, was connected to a type K potentiometer for temperature measurements. The thermo-couple was calibrated against the melting points of tin, bismuth, and the silver-copper eutectic and the boiling point of water. Since the temperature readings could be reproduced to 0.2°C, and the accuracy of the temperature standards in this range is slightly better than 0.5°C, it seems reasonable to assume that the temperature readings are reliable to approximately 0.5°C. The cooling rate could be controlled by varying the amount of insulation surrounding the crucible. Three or four layers of asbestos paper, 1/16r, in. thick, sufficed to give a cooling rate of from 1° to 2°C per minute. Undercooling was slightly noticeable. This condition was minimized by vigorous stirring, since the advantage of using slower rates was too small to justify the greater expenditure

Jan 1, 1947

By A. B. Parsons

Jan 1, 1971

By Robert Thomas

DURING the past 20 years the advantages of reinforced concrete as a substitute for timbering in so-called permanent mine openings have been fully recognized, and its use has become almost general practice in the larger mines. The term "permanent mine openings" is used advisedly and is assumed to embrace such openings as ventilation shafts, material shafts and main hoisting shafts, with their adjacent stations, ore pockets, etc. In the concreting of such openings, the actual cost as compared with that of timbering has been of secondary consideration, the support of large openings, elimination of fire hazards, and prevention of inter-ruptions to production being the primary objectives. The ultimate economy, however, of lining such openings with concrete when they are to remain in use during the entire life of the mine, and especially when they are in bad ground, will seldom be questioned. During this 20-year period there have appeared in engineering publi-cations a number of interesting articles on the use of concrete in mines, nearly always describing some specific project of major proportions, such as the concreting of ore pockets, large stations or main hoisting shafts. Such articles are unquestionably of interest, since the projects require considerable engineering thought, not only in the method of excavating large openings, but in their engineering design as well. Concreting of main hoisting shafts, particularly when this is done with the least possible interruption to production, provides some interesting problems. The concreting of haulage drifts of the dimensions commonly found in mines, on the other hand, soon develops into a routine operation, there-fore it is with some hesitancy that the author attempts to prepare an article on this subject. The writer can recall only one article on the concreting of mine haulageways, although several articles have been written concerning the concreting of tunnels considerably larger in dimensions than those required in general mine practice.

Jan 1, 1936

By H. E. Criner, M. G. Driessen

THE cyclone thickener has two important applications in wet washing plants: (1) water clarification, and (2) fine coal recovery. The thickener consists of a conical chamber into which the fluid is injected through a tangential nozzle at the periphery of the large end. The solids of the slurry are concentrated and removed from the apex of the cone while the "thinner" portion is discharged from a central tube in a flat head at the large end, fig. 1. The advantages of the cyclone thickener are that large volumes of slurry may be treated with small space requirements and that the underflow concentration may be controlled easily and readily to meet varying feed conditions. Control of Washery Water Solids Concentration: The first requirement, in the process of controlling solids concentration, is that the solids be removed from the body of circulating water at the rate at which they are introduced. If this condition is satisfied the concentration will remain at a fixed value and will not increase to uncontrollable levels. The second requirement is that the solids concentration

Jan 1, 1951

By M. G. Driessen, H. E. Criner

THE cyclone thickener has two important applications in wet washing plants: (1) water clarification, and (2) fine coal recovery. The thickener consists of a conical chamber into which the fluid is injected through a tangential nozzle at the periphery of the large end. The solids of the slurry are concentrated and removed from the apex of the cone while the "thinner" portion is discharged from a central tube in a flat head at the large end, fig. 1. The advantages of the cyclone thickener are that large volumes of slurry may be treated with small space requirements and that the underflow concentration may be controlled easily and readily to meet varying feed conditions. Control of Washery Water Solids Concentration: The first requirement, in the process of controlling solids concentration, is that the solids be removed from the body of circulating water at the rate at which they are introduced. If this condition is satisfied the concentration will remain at a fixed value and will not increase to uncontrollable levels. The second requirement is that the solids concentration

Jan 1, 1951

By V. B. Kurfman

The temperature, strain rate, and orientation deDendence of defbrnzation of single-crystal MgAg has been examined. The crystals exhibit a tendency to single glide and little or no hardening at 25°C for many orientations. A much higher hardening rate is observed when multiple glide occurs, such as can be initiated by surface defects. The tendency for easy glide becomes less dependent on surface preparation and orientation as T — 100°C and bars so tested often fail after one-dimensional necking-. At T > 200°C (transition temperature for single-crystal notch sensitivity and poly crystalline ductility) single glide diminishes and two-dirnensionul necking begins. The crystals do not strictly obey a critical resolved shear stress law, but show the influence of {loo) cracks in determining the slip mode. The results are correlated with the difficulty of sciperdzslocation intersection and semibrittle behavior of this compound in single-crystal and poly crystalline form. Comparisons are made with the slip selection mode observed in tungsten, with the reported observations of easy glide in bee metals. and with the mechanical behavior of poly crystalline MgAg. PREVIOUS work on tensile deformation of polycrys-talline MgAgl and bending deformation of single-crystal MgAg2 has shown that the compound is semi-brittle (i.e., notch and grain boundary brittle). If this semibrittleness is supposed to result from the difficulty of multiple glide (associated with the problems of superdislocation intersection) one might expect single crystals deformed in tension to show pronounced single glide and strong orientation dependence of hardening rate. These experiments were done to examine this supposition and to study the tensile deformation of a highly ordered system which may be considered bcc if the difference between the two kinds of atoms is ignored (actual structure: CsC1). EXPERIMENTAL Single-crystal ingots were grown by directional freezing as previously described.' These ingots were sliced into a by a by 2 in, rectangular bars by electric discharge machining, then round tensile bars were conventionally machined to 1/8-in.-diam by 1-in.-long reduced section. The bars were typically tested without an anneal because of the problem of magnesium vapor loss and they were typically tested as mechanically polished. The analyses are within the same limits as those reported earlier; i.e., the average composition for each specimen is within 0.5 at. pct of stoichiometry, while the total range from end to end in a given specimen varies from 0.7 to 1.4 at, pct. There has been no indication in the results of any variation in slip or fracture mode attributable to the composition fluctuations. The slip systems were determined by two-surface analysis of the bars after testing to failure at room temperature. Single glide was so dominant that there was little difficulty in identification of the dominant slip system even though the tensile elongation to failure often approached 7 to 8 pct in room-tempera- ture tests. Elevated-temperature testing was done in a silicone oil bath and low-temperature testing was done in liquid Np or a dry-ice bath. All stress measurements are reported as engineering stress unless otherwise specified, and crosshead travel is used as the strain measurement. RESULTS The tendency toward single glide is best seen in the pictures, Figs. 1, 2, and 3, which depict deformation at fracture as a function of test temperature. While it is possible to find regions of secondary slip by careful microscopy, such regions are very small. The development of a ribbon-shaped configuration from an initially round section bar pulled at 100°C is typical, occurred by single glide, and illustrates the degree to which such glide continues. At temperatures =100°C the bars typically show elongation of 20 to 50 pct by predominently single glide. Despite the large elongation, fracture even at 150°C occurs in a brittle mode, Fig. 2, in the sense that it is an abrupt failure which shows no discernible necking in the second dimension of the bar's cross section (i.e., there is no appreciable action of any slip modes which would decrease the broad dimension of the cross section). Near 200°C the fracture mode changes slightly. Although most of the sample extension is by single glide, after the bar develops the characteristic ribbon shape it begins to neck in the second (i.e., broad) cross-sectional dimension. The bar becomes very thin in the "necked down" region, Fig. 3, and the reduction in area approaches 100 pct. Often there oc-

Jan 1, 1967

By H. I. Aaronson, W. L. Winterbottom, G. M. Pound

On the basis of a statistical thermodynamic treatment of the data of smithz2 on the activity of carbon in austenite, a Darken and smith23 deduced that the interaction energy, wy, between carbon atoms occupying nearest-neighboring interstitial sites is repulsive. Aaronson, Domian, and pound 24 (ADP) have applied two different statistical thermodynamic analyses to the same data. One analysis, a composite of the treatments of Darken and Smith,23 Speiser and Spret-nak," and Kaufman, Radcliffe, and Cohen,26 primarily takes account of the positional entropic effects of wy in dilute solutions. The other, due to Lacher 27 and Fowler and Guggenheim," is also applicable to more concentrated solid solutions. The equations which both analyses produce for a,, can be rearranged so that, when In a,, is plotted against the appropriate function of the carbon content of the austenite, the plot will have a slope of unity when the correct value of wy is employed. Since no other constant need be simultaneously evaluated in order to make this determination, ascertaining the most probable value of wy from Smith's data on the bases of these analyses was an elementary problem in least-squares statistics. ADP demonstrated that the wy's obtained from both analyses vary with temperature in a statistically significant manner. McLellan, Gerrard, Horowitz, and sprague 29 (MGHS), on the other hand, have recently made a new statistical thermodynamic study of a,, and have concluded from this study that wy is independent of temperature. The equation which they derived for a,, is: where 0 = ratio of the mole fraction of carbon atoms to that of iron atoms, z = number of sites from which occupancy is excluded by the presence of a carbon atom and the repulsive character of its interaction with nearest-neighboring carbon atoms (z = zb in Ref. 24), and x = a geometric parameter taking account of overlapping of the exclusion shells of nearby carbon atoms. z is 1 when wy = 0 and 13 when wy = Q. For a given value of z there is a definite value of X . In the absence of an equation connecting z and X, MGHS computed geometrically the value of x at several integral values of z; x increases from 0.47 to 8.67 as z is increased from 2 to 5. MGHS fitted Eq. [I] to the a,, data of Ellis, Davidson, and Bodsworth30 at 925° and 1050°C and to the data of smithz2 at 1000°C. Confining z to integral values in the range 4 to 6, and also somewhat restricting AG, the values of z, X, and AG were sought which would minimize the average root mean square percent deviation, D, of the calculated a,, values from those obtained experimentally. Finding that D was almost always smallest when z = 5, they concluded that z is independent of temperature. Since:23, 26 where R = gas constant and T = absolute temperature, and w,, was considered to be similarly invariant, this statement cannot be strictly true. The temperature range employed, however, was small and the interval between the values of z tested was sufficiently large so that the results could still be consistent with a constant The statistical treatment of the a,, data applied by MGHS is clearly quite approximate. Since more than three values of a,, are available at each temperature, z, and X, and AG have actually been over deter mined, rather than underdetermined as their treatment implies. In order to make more complete and exact use of the a,, data, we shall employ the Legendre Method of Least Squares, as described by Whittaker and Robinson. This technique permits conversion of the overdetermined system of equations produced by the substitution into Eq. [I] of the available pairs of a,, and 0 data at a given temperature into an even determined system. Solution of the latter system yields the most probable value of each of the three constants. This procedure will allow a statistically rigorous test to be made of the conclusion drawn by MGHS in respect of the temperature dependence of In order to obtain linear iiequations of conditions" from Eq. [I], the exact values of the three unknown constants are replaced by G/RT = =/RT + y, where z, i, and aG are estimated values of the constants. This allows the conditional equations to be written in the form:'l where fi -f6, i, =/RT) = the right-hand side of Eq. [I] for a given pair of ayi and values. When applied to Eq. [I], these relationships become: The i equations of condition are reduced to three "normal equations" in the manner discussed by Whittaker and Robinson. The normal equations are then solved for a, ß, and y. Both of these operations are most conveniently performed by means of the computer technique of Winterbottom and Gjostein.32 This technique was used iteratively until the value of 0 (the most sensitive of the three correction factors) became 10.01. (Until they became small, a, 8, and y

Jan 1, 1969

By W. C. McClain

The amount of vertical subsidence occurring over a longwall operation is a function of the thickness of material removed, the quantity and quality of any fill material, the width of the extraction, and the depth. The relationship between these variables is empirically determined, and subsidence can be predicted using only a few easily established constants which are subject to local conditions, such as the angle of draw. Associated with the vertical subsidence are both tensional and compressional horizontal strains. The component of strain in the direction of face advance is temporary, while the component perpendicular to the direction of working is permanently retained by the ground. It is these horizontal strains and the vertical strain (tilt) which result in damage to surface structures. It is possible to ameliorate the consequences of mining subsidence by utilizing the well-proved techniques described in this paper in the underground operations and on the surface. INTRODUCTION In the past, American mining practice in stratified deposits has been mostly restricted to production by the room-and-pillar system where a sizable percentage of the salable product is left in place as pillars. These pillars are usually regularly spaced and provide a permanent support for the roof of the mine and the surface above. The longwall system employs an advancing face which may be as much as several hundred yards long and some sort of breaking and loading machine which moves back and forth along the length of the face. The roof is supported behind the face only to a distance required to provide working space for the production machine. The supports are then withdrawn and the roof is allowed to cave. The longwall system therefore possesses the various advantages of complete extraction, thus effectively increasing reserves, while at the same time eliminating the necessity and cost of installing artificial supports such as roof bolts and heavy steel girders over large areas. Longwall mining has long been practiced in Europe, where it has undergone an involved development, culminating in the recent perfection of powered-loading machines and automatic self-propelled supports, offering high productivity. With ever-in creasing

Jan 1, 1967

By H. S. Fleming

My original intention was to give a full account of Southern furnaces, ores and cokes; but, owing to the difficulty of getting reliable information, I confine this paper to a general description of the ores used in, and immediately around, Chattanooga. Mr. L. S. Colyar, Manager of the Rising Fawn furnace, wrote me in answer to an inquiry as to what ores they were using, " Below I give you analyses of the mixture of ore we have been using for the past seven or eight years. We haven't a complete analysis of any ores, but I will give them to you as I have them. Attalla Soft Rising Fawn Hard Rising Fawn Red Ore. Red Ore. Soft Ore. Iron,.... 50.60 38.48 46.82 Silica,. .. 11.69 7.32 22.69 Phosphorus,. .. 1.06 .319 .350 This is a fair average of all the ores we get in this section." The following analyses of Birmingham soft ore were received from the Morris Mining Co., of that place. No. 1. NO. 2. No. 3. No. 4. Iron.....51.60 54.88 51.04 51.20 Silica,. .. 19.32 10.60 17.32 17.08 Alumina,....19 .88 1.18 Phosphorus,. ..129 .287 .116 .464 Mine No. 1, second vein, shows: iron, 46.40; alumina, 4.92; phosphorus,.212; silica, 19.60. Mine No. 1, by analyses obtained from the Mary Pratt Furnace CO., shows: Iron. Silica. Fine red ore,.49.00 18.38 Lump red ore,...54.42 17.10 Bottom vein,.50.00 21.38 Bottom vein,.41.24 13.52 A lot of this ore delivered in Chattanooga gave : iron, 53.32; alumina, 2.10; phosphorus,.529; silica, 18.03.

Jan 1, 1887

By H. Fechtig, R. H. Buck, A. G. Guy

MULTIPHASE diffusion has been studied for many years in two-component systems1,2 and many of the experimental aspects are now fairly well understood.314 Although by no means all of the problems connected with the two-component case have been solved,' attention has recently been directed to the more complex situation involving three components. The pioneer work of Clark and Rhines6 yielded a qualitative picture of the types of behavior that can occur, and Clark7 has suggested conventions for describing the various phenomena. Kirkaldy and co-workers8,9 have made quantitative studies in several ternary systems and have offered explanations of the occurrence of isolated and nonisolated precipitates. At present, however, there is no comprehensive theory for the variety of phenomena observed in ternary, multiphase diffusion. By analogy with several studies that have been made of multiphase diffusion in the binary Cu-Zn system,2'10'11 a similar exploratory study was made of Cu-Zn-Ni alloys lying along the line in the ternary diagram from the point 80 Cu-20 Ni to the zinc corner of the diagram, Fig. 1. A principal question to be answered was whether initially plane interfaces would remain plane during the course of one-dimensional diffusion. The diffusion specimens studied are described in Table I. The five separate alloys from which they were made were melted in evacuated Vycor capsules from 99.9 pct purity copper, zinc, and nickel. Since some of the alloys were too brittle to be swaged, all of the alloys were used in the cast condition. To facilitate later homogenization, the molten alloys were solidified by plunging the capsule in water. Homogenization heat treatment was done at 720°C for 20 hr. The five nominal compositions in weight percent zinc and nickel, respectively, were: 37.5, 12.5; 44.0, 11.2; 50.0, 10.0; 55.0, 9.0; 65.0, 7.0. Ln Table I the alloys are identified only by their zinc content. Sandwich-type diffusion specimens were prepared by pressure welding disk specimens, each about 3 mm high by 10 mm in diameter. Welding was done in a special threaded vise which was heated at 500°C for about an hour in an atmosphere of flowing hydrogen. A measurement of the separation of the phase interfaces was made on a polished flat on the welded specimen, and then the specimen was sealed in an evacuated capsule and given the diffusion treatment shown in Table I. The diffused specimen was sectioned longitudinally

Jan 1, 1965

Map

Jan 1, 1941

By Clarence Zener

THE internal friction of nonferrous metals vibrating at low stress amplitudes has so far always been successfully interpreted in terms of inhomogeneities of one sort or another. Examples are the fluctuation of stress across a specimen vibrating transversely,1,2,3 the stress inhomogeneities due to the elastic anisotropy and partial random orientation of the individual crystallites,4,5 localized weak regions introduced by cold-working,6,7 grain boundaries and possibly twinning planes.8,9 Perfect single crystals are, by definition, homogeneous. Actual single crystals usually, perhaps always, contains some imperfections. The present investigation. was undertaken to determine whether the internal friction of single crystals may likewise be attributed to inhomogeneities. This study was made possible through the gift of a large single crystal of 70-30 alpha brass by H. L. Burghoff, of the Chase Brass and Copper Co. The specimen, ½ in. in diameter and 10 in. long, was similar to samples previously described by Mr. Burghoff.10 EXPERIMENTAL METHOD The experimental method used has previously been described in Institute papers.5,6,9 The measure of internal friction adopted here, 1/Q, is (1/p) X the logarithmic decrement, a measure used by some writers, and is also (1/2p) X the specific damping capacity, a measure used by other writers. In all measurements the stress level was kept so low that the measurements were independent of stress level. In all measurements in which the temperature was varied, observations were made as the specimen slowly cooled from its highest temperature. The specimen was vibrated transversely. Observations were made at the funda¬mental frequency and at the first overtone, of about 620 and 1710 cycles per second, respectively. No attempt was made to avoid acoustical losses. EXPERIMENTAL RESULTS The specimen was annealed for several hours at 450°C. The temperature dependence of the internal friction was then determined from room temperature to 400°C. As shown in Fig. 1, the internal friction increased by only a factor of 2 from room temperature to 300°C., then by a factor of l00 during the next 100° interval. These measurements are consistent with the view that the observed internal friction is the superposition of two distinct parts. One, dominant at room temperature, is nearly independent of temperature. This part may be accounted for by acoustical losses and by transverse thermal currents. It was not further investigated. The second part, when plotted in the manner of Fig. I, lies upon a straight line. Therefore it has a heat of activation H; i.e., it varies with temperature as Internal friction e~H/RT [I]

Jan 1, 1942